Characterization of superfine wool powder/poly(propylene) blend film

Superfine wool powder was blended and extruded with poly(propylene) (PP) to produce blend pellets, and the extruded pellets were hot-pressed into a blend film. SEM photographs show that the powder could be uniformly incorporated with PP after extrusion. FT-IR spectra shows that no substantial changes occurred in the chemical structure of both PP and wool powder in the blend film. X-Ray diffraction analysis indicates that crystallinity of the blend film was much higher than that of the wool powder and little lower than that of PP. TG-tested results indicate that the thermal stability of the blend film declined with an increase in the powder content. Endothermic peaks of the wool powder in the blend film become more obvious as the powder content increases. Mechanical properties decline greatly with an increase in the wool powder content in the blend film.

Characterization of hot-pressed films from superfine wool powder

In this study, superfine wool powder was plasticized with glycerol and hot-pressed into a film. Scanning electron microscopy photos showed that the superfine wool powder could be molded into a smooth film and that the wool powder was distributed evenly in the cross section of the film. Fourier transform infrared analysis revealed no substantial changes in the chemical structure of the wool powder after hot pressing, but the absorbing peaks of glycerol were found in the spectrum. X-ray diffraction analysis showed that the overall crystallinity increased after the wool powder was hot-pressed into film. Thermogravimetry (TG) analysis indicated that the thermal stability of the hot-pressed film decreased. A transition point appeared in the TG curve of the wool hot-pressed film as glycerol was added. The differential thermal analysis curve of the film showed sharp absorbing peaks similar to that of wool powder. With increasing glycerol content, the film showed increasing ductility and softness.

Bleaching and dyeing of superfine wool powder/polypropylene blend film

Fibers based regenerated protein draw much attention for recycling discarded protein resources and can produce biodegradable and environmental friendly polymers. In this study, superfine wool powder is blended with polypropylene (PP) to produce wool powder/PP blend film through extrusion and hot-pressing. Hydrogen peroxide is used to bleach the black colored surface of the blend films. The effects of peroxide concentration, bleaching time and powder content on the final whiteness and mechanical properties of the blend films are investigated.

The bleached films are dyed with acid red dyes and the dyed color is evaluated using a Computer Color Matching System. Color characters of dyed films, such as L*, a*, b*, ΔE*ab, C*ab and K/S values are measured and analyzed. The study not only reuses discarded wool resources into organic powder, widens the application of superfine wool powder on polymers, but also improves the dyeing properties of PP through the addition of protein content.

Thermoplastic film from superfine wool powder

In this paper a research work is described in which superfine wool powder was plasticised by glycerol and hot-pressed into a kind of thermoplastic film. SEM photos show that the powder is moulded into a smooth surface and is conglutinated into a continuous phase in the cross-section of the film. The glycerol content, moulding pressure, temperature and moulding time were changed in the moulding process. The sizes and thickness aw well as tensile strength, modulus, breaking elongation and breaking energy of the films were also tested to investigate the thermoplasticity and mechanical properties of the films. The best moulding techniques included a glycerol content of 30%, a moulding pressure of 5 MPa, a temperature of 160 °C and a moulding time of 5 minutes.

Characterization and sorption ability of wool powder

This work focused on the characterisation of wool powders and their sorption capacity for dyes and metal ions. It provides new information to the field of wool and the potential use of wool to sorb contaminants from wastewater. It also suggests a new use for inferior and waste wool.

Study on the antibacterial properties of superfine wool powder part I : experiment

The superfine wool-powder was prepared by ball and jet milling. According to FZ/T 01021-92 method the bacteriostatic property of the wool-powder was tested. The results showed that wool-powder had excellent antibacterial activity against Escherichia coli (E. coli) and Staphylococcus (MRSA), and the antibacterial rate of E. coli could reach 85% and the MRSA could exceed 70%. The IR spectroscopy and X-ray diffraction analysis were used to discuss the antibacterial properties of superfine wool-powder.

Dyeing properties of PVA/superfine wool powder blend filaments

Polyvinyl alcohol/superfine wool powder blend filaments were prepared to improve teh dyeing properties of polyvinyl alcohol (PVA) filaments. The average size of superfine wool powder was 2.01 um. SEM microphotgraphs showed good compatibility between superfine wool powder and PVA matrix. The PVA/superfine wool powder blend solution showed good spinningability. With the incerease in superfine wool powder content, the dye uptake, a* value and K/S value of PVA/superfine wool powder blend filaments increased steadily. It was worth noting that the dyeing properties of blend filaments were almost similar with that of superfine wool powder when powder content was 33.3%

Thermal and chemical properties of wool powders

Wool powders with different particle sizes were examined in terms of their crystal structures, thermal properties, surface chemical compositions and moisture regains. It was found that the crystallinity of wool powders was increased, and the moisture regains were decreased as the particle sizes of wool powders were reduced. For comparison, the properties of activated charcoal were also investigated. The higher dye uptake of activated charcoal at pH 10. compared to that of wool powder, could be due to its greater surface area and porous structure.

Wool powders used as sorbents to remove Co2+ ions from aqueous solution

The Co2+ sorption of two wool powders was investigated using its radioisotope 57Co (T1/2=271.8 days and γ=122.1 and 136.5 keV) as a tracer. The effects of the type of buffer, the pH value, the contact time and the initial concentration of Co2+ on the sorption behaviour of wool powders were studied. The Co2+ releasing ability of wool powders and the re-use of wool powders to sorb Co2+ were also examined. The optimum sorption of Co2+ by the powders occurred at pH 8 in phosphate buffer and pH 10 in ammonium sulphate buffer. Fourier-transform infrared spectroscopy (FTIR) was used to study the changes in chemical structure of the wool after exposure to both buffer solutions. Compared to the untreated wool fibre, the fine wool powders showed rapid sorption rates and high sorption capacities for Co2+. Co2+ ions were recovered after exposing the Co2+ loaded wool to HCl (0.1 M) and buffer at pH 3 (glycine/sodium chloride). After releasing Co2+ ions from wool powders, the efficiency of wool powders re-used to sorb Co2+ was 80% of that of the fresh wool powders. It is concluded from this study that wool powder can be used as an efficient sorbent to remove and release Co2+ from solution.

A morphology-related study on photodegradation of protein fibres

The wool fibre has a complex morphology, consisting of an outer layer of cuticle scales surrounding an inner cortex. These two components are hard to separate effectively except by using harsh chemical treatments, making it difficult to determine the susceptibility of the different components of the fibre to photoyellowing. An approach to this problem based on mechanical fibre modification is described. To expose the inner cortex of wool to different degrees, clean wool fibres were converted into ‘powders’ of various fineness via mechanical chopping, air-jet milling, ball milling or their combination. Four types of powdered wool (samples A, B, C and D) were produced with reducing particle size distributions and an increasing level of surface damage as observed using SEM. Sample A contained essentially intact short fibre snippets and sample D contained a large amount of exposed cortical materials. Samples B and C contained a mixture of short fibre snippets and cortical materials. Solid wool discs were then compressed from the corresponding powder samples in a polished stainless steel die to enable colour measurement and UV irradiation studies. ATR-FTIR studies on powder discs demonstrated a small shift in the amide I band from 1644 cm−1 for disc A to 1654 cm−1 for disc D due to the different structures of the wool cuticle and cortex, in agreement with previous studies. Similarly an increase in the intensity ratio of the amide I to amide II band (1540 cm−1) was observed for disc D, which contains a higher fraction of cortical material at the surface of the disc.

Discs prepared from sample D appeared the lightest in colour before exposure and had the slowest photoyellowing rate, whereas discs made from powders A–C with a higher level of cuticle coverage were more yellow before exposure and experienced a faster rate of photoyellowing. This suggests that the yellow chromophores of wool may be more prevalent in cuticle scales, and that wool photoyellowing occurs to a greater extent in the cuticle than in the cortex. Photo-induced chemiluminescence measurements showed that sample D had a higher chemiluminescence intensity after exposure to UVA radiation and a faster decay rate than samples A and B. Thus one of the roles of the wool cuticle may be to protect the cortex by quenching of free radical oxidation during exposure to the UV wavelengths present in sunlight.

Review on fabrication and applications of ultrafine particles from animal protein fibres

Protein fibre wastes from animal hairs, feathers and insect secreted filaments can be aptly utilized by converting them into ultra-fine particles. Particles from animal protein fibres present large surface-to-weight ratio and significantly enhanced surface reactivity, that have opened up novel applications in both textile and non-textile fields. This review article summarizes the state-of-the-art routes to fabricate ultrafine particles from animal protein fibres, including direct route of mechanical milling of fibres and indirect route from fibre proteins. Ongoing research trends in novel applications of protein fibre particles in various fields, such as biomedical science, environmental protection and composite structures are presented. © 2014 The Korean Fiber Society and Springer Science+Business Media Dordrecht.

The characterization and chemical reactivity of powdered wool

Wool powders with various particle sizes have been produced using different milling techniques. Scanning electron microscopy (SEM) showed gradual breakdown of the fibre as it was progressively converted into powder form. Chlorination enhanced the effectiveness of subsequent air-jet milling. X-ray photoelectron spectroscopy (XPS) revealed an increase in the surface concentrations of oxygen and nitrogen, and a decrease in carbon and sulphur on conversion of the fibres into powders, as the cortex became exposed on the powder surface. An increased surface concentration of cysteic acid was observed for the chlorinated powder. Rapid uptake of dye by wool powders was observed in situations where there was virtually no uptake by the original fibre. Hydrophobic dyes were more readily sorbed than were hydrophilic dyes. The chlorination treatment led to a decrease in the sorption of acid dyes. Confocal microscopy, used in conjunction with a fluorescent stain, showed that chemicals were able to penetrate wool particles, even at room temperature. The rate and extent of uptake of dye by the finer powders were comparable to that obtained with activated charcoal, even though the surface area of the charcoal was 100 times greater.

Protein fibre powder and new applications

Protein fibers such as silk and wool have been used as textile fibers for centuries. It is only in recent years that these fibers have been converted into fine powder forms for non-textile applications. This presentation will cover our recent research in protein fiber powders. Ultra-fine powders from different protein fibers have been produced using a combination of media and non media milling techniques. New application examples of these fine powders are discussed. These applications include hybrid fibers combining the advantages of natural and synthetic polymer fibers, tissue engineering composite scaffolds with enhanced biomechanical properties, and metal ion absorption.