Isolamento do tungstênio da volframita da mina de Igarapé Manteiga (Rondônia - Brasil) por lixiviação ácida

We report results of the efficiency of tungsten extraction from wolframite concentrate (containing 61.5 wt % WO3) from the Igarapé Manteiga mine (state of Rondônia, Brazil) through acid leaching with strong mineral acids at 100 ºC and 400 rpm for 2-4 h. HCl yielded insoluble matter containing the highest WO3 content (90 wt %). This solid was dissolved in concentrated NH3(aq) at 25 ºC and the insoluble matter filtrated. The filtrate was slowly evaporated. 70 wt % of the tungsten present in the starting concentrate material was recovered as ammonium paratungstate (APT).

Geology of the Sand Creek porphyry molybdenum prospect /

The Sand Creek Prospect is located within the eastern exposed margin of the Coast Plutonic Complex. The occurrence is a plug and dyke porphyry molybdenum deposit. The rock types, listed in decreasing age: 1) metamorphlc schists and gneisses; 2) diorite suite rocks - diorite, quartz diorite, tonalite; 3) rocks of andesitic composition; 4) granodiorites, coarse porphyritic granodiorite, quartzfeldspar porphyry, feldspar porphyry; and 5) lamprophyre. Hydrothermal alteration is known to have resulted from emplacement of the hornblende-feldspar porphyry through to the quartz-feldspar porphyry. Molybdenum mineralization is chiefly associated with the quartz-feldspar porphyry. Ore mineralogy is dominated by pyrite with subordinate molybdenite, chalcopyrite, covelline, sphalerite, galena, scheelite, cassiterite and wolframite. Molybdenite exhibits a textural gradation outward from the quartz-feldspar porphyry. That is, disseminated rosettes and rosettes in quartz veins to fine-grained molybdenite in quartz veins and potassic altered fractures to fine-grained molybdenite paint or 6mears in the peripheral zones. The quartz-feldspar porphyry dykes were emplaced in an inhomogeneous stress field. The trend of dykes, faults and shear zones is 0^1° to 063° and dips between 58° NW and 86* SE. Joint Pole distribution reflects this fault orientation. These late deformatior maxima are probably superimposed upon annuli representing diapiric emplacement of the plutons. A model of emplacement involving two magmatic pulses is given in the following sequence: Diorite pulse (i) dioritequartz diorite, (ii) tonalites; granodiorite pulse (iii) hornblende-fildspar microporphyry, hornblende/biotite porphyry, (iv) coarse grained granodiorite, (v) quartz-feldspar porphyry, (vi) feldspar porphyry, and (vii) lamprophyre. The combination of plutonic and coarse porphyritic textures, extensive propylitic overprinting of potassic alteration assemblages suggests that the. prospect represents the lower reaches of a porphyry system.

Sn-polymetallic greisen-type deposits associated with late-stage rapakivi granites, Brazil: fluid inclusion and stable isotope characteristics

Tin-polymetallic greisen-type deposits in the Itu Rapakivi Province and Rondonia Tin Province, Brazil are associated with late-stage rapakivi fluorine-rich peraluminous alkali-feldspar granites. These granites contain topaz and/or muscovite or zinnwaldite and have geochemical characteristics comparable to the low-P sub-type topaz-bearing granites. Stockworks and veins are common in Oriente Novo (Rondonia Tin Province) and Correas (Itu Rapakivi Province) deposits, but in the Santa Barbara deposit (Rondonia Tin Province) a preserved cupola with associated bed-like greisen is predominant. The contrasting mineralization styles reflect different depths of formation, spatial relationship to tin granites, and different wall rock/fluid proportions. The deposits contain a similar rare-metal suite that includes Sri (+/-W, +/-Ta, +/-Nb), and base-metal suite (Zn-Cu-Pb) is present only in Correas deposit. The early fluid inclusions of the Correas and Oriente Novo deposits are (1) low to moderate-salinity (0-19 wt.% NaCl eq.) CO2-bearing aqueous fluids homogenizing at 245-450 degreesC, and (2) aqueous solutions with low CO2, low to moderate salinity (0-14 wt.% NaCl eq.), which homogenize between 100 and 340 T. In the Santa Barbara deposit, the early inclusions are represented by (1) low-salinity (5-12 wt.% NaCl eq.) aqueous fluids with variable CO2 contents, homogenizing at 340 to 390 T, and (2) low-salinity (0-3 wt.% NaCl eq.) aqueous fluid inclusions, which homogenize at 320380 degreesC. Cassiterite, wolframite, columbite-tantalite, scheelite, and sulfide assemblages accompany these fluids. The late fluid in the Oriente Novo and Correas deposit was a low-salinity (0-6 wt.% NaCl eq.) CO2-free aqueous solution, which homogenizes at (100-260 degreesC) and characterizes the sulfide fluorite-sericite association in the Correas deposit. The late fluid in the Santa Barbara deposit has lower salinity (0-3 wt.% NaCl eq.) and characterizes the late-barren-quartz, muscovite and kaolinite veins. Oxygen isotope thermometry coupled with fluid inclusion data suggest hydrothermal activity at 240-450 degreesC, and 1,0-2.6 kbar fluid pressure at Correas and Oriente Novo. The hydrogen isotope composition of breccia-greisen, stockwork, and vein fluids (delta(18)O quartz from 9.9parts per thousand to 10.9parts per thousand, deltaDH(2)O from 4.13parts per thousand to 6.95parts per thousand) is consistent with a fluid that was in equilibrium with granite at temperatures from 450 to 240 degreesC. In the Santa Barbara deposit, the inferred temperatures for quartz-pods and bed-like greisens are much higher (570 and 500 degreesC, respectively), and that for the cassiterite-quartz-veins is 415 degreesC. The oxygen and hydrogen isotope composition of greisen and quartz-pods fluids (delta(18)O(qtz-H2O)=5.5-6.1parts per thousand) indicate that the fluid equilibrated with the albite granite, consistent with a magmatic origin. The values for mica (delta(18)O(mica-H2O)=33-9.8parts per thousand) suggest mixing with meteoric water. Late muscovite veins (delta(18)O(qtz-H2O)=-6.4parts per thousand) and late quartz (delta(18)O(mica-H2O)=-3.8parts per thousand) indicate involvement of a meteoric fluid. Overall, the stable isotope and fluid inclusion data imply three fluid types: (1) an early orthomagmatic fluid, which equilibrated with granite; (2) a mixed orthomagmatic-meteoric fluid; and (3) a late hydrothermal meteoric fluid. The first two were responsible for cassiterite, wolframite, and minor coluChange in the redox conditions related to mixing-of magmatic and meteoric fluids favored important sulfide mineralization in the Correas deposit. (C) 2004 Elsevier B.V. All rights reserved.

beta-ZnMoO4 microcrystals synthesized by the surfactant-assisted hydrothermal method: Growth process and photoluminescence properties

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Structural Refinement and Photoluminescence Properties of MnWO4 Nanorods Obtained by Microwave-Hydrothermal Synthesis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of partial preferential orientation and distortions in octahedral clusters on the photoluminescence properties of FeWO4 nanocrystals

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influence of the thermal treatment in the crystallization of NiWO4 and ZnWO4

NiWO4 and ZnWO4 were synthesized by the polymeric precursor method at low temperatures with zinc or nickel carbonate as secondary phase. The materials were characterized by thermal analysis (TG/DTA), infrared spectroscopy, UV-Vis spectroscopy and X-ray diffraction. NiWO4 was crystalline after calcination at 350 A degrees C/12 h while ZnWO4 only crystallized after calcination at 400 A degrees C for 2 h. Thermal decomposition of the powder precursor of NiWO4 heat treated for 12 h had one exothermic transition, while the precursor heat treated for 24 h had one more step between 600 and 800 A degrees C with a small mass gain. Powder precursor of ZnWO4 presented three exothermic transitions, with peak temperatures and mass losses higher than NiWO4 has indicating that nickel made carbon elimination easier.

Yellow ZnxNi1-xWO4 pigments obtained using a polymeric precursor method

New tungstate-based ceramic pigments, displaying ZnxNi1-xWO4 stoichiometry, were obtained at low temperature using a polymeric precursor method. The powder precursors were milled in an attritor mill in an alcoholic rnedium and heat treated for 12 h. yielding homogeneous and crystalline powder pigments. Characterization (TG/DTA, XRD, IR and colorimetry) showed that mass loss increased with increasing Zn contents. Despite the presence of secondary phases and impurities, the wolframite phase was present in all samples. IR analysis revealed bands related to Me-O and [WO6](6-) group stretching was observed. The intensity of the yellow color of the pigments increased with increasing amount of nickel. (c) 2007 Elsevier Ltd. All fights reserved.

A combined theoretical and experimental study of electronic structure and optical properties of β-ZnMoO4 microcrystals

In this paper, a combined theoretical and experimental study on the electronic structure and photoluminescence (PL) properties of beta zinc molybdate (β-ZnMoO4) microcrystals synthesized by the hydrothermal method has been employed. These crystals were structurally characterized by X-ray diffraction (XRD), Rietveld refinement, Fourier transform Raman (FT-Raman) and Fourier transform infrared (FT-IR) spectroscopies. Their optical properties were investigated by ultraviolet-visible (UV-Vis) absorption spectroscopy and PL measurements. First-principles quantum mechanical calculations based on the density functional theory at the B3LYP level have been carried out. XRD patterns, Rietveld refinement, FT-Raman and FT-IR spectra showed that these crystals have a wolframite-type monoclinic structure. The Raman and IR frequencies experimental results are in reasonable agreement with theoretically calculated results. UV-Vis absorption measurements shows an optical band gap value of 3.17 eV, while the calculated band structure has a value of 3.22 eV. The density of states indicate that the main orbitals involved in the electronic structure of β-ZnMoO4 crystals are (O 2p-valence band and Mo 4d-conduction band). Finally, PL properties of β-ZnMoO4 crystals are explained by means of distortions effects in octahedral [ZnO6] and [MoO6] clusters and inhomogeneous electronic distribution into the lattice with the electron density map. © 2013 Elsevier Ltd. All rights reserved.

Effect of partial preferential orientation and distortions in octahedral clusters on the photoluminescence properties of FeWO4 nanocrystals

This communication is a report of our initial research to obtain iron tungstate (FeWO4) nanocrystals by the microwave-hydrothermal method at 170 degrees C for 45 min. X-ray diffraction patterns showed that the FeWO4 nanocrystals prepared with polyethylene glycol-200 have a partial preferential orientation in the (011) plane in relation to other nanocrystals prepared with sodium bis(2-ethylhexyl) sulfosuccinate and water. Rietveld refinement data indicates that all nanocrystals are monophasic with wolframite-type monoclinic structures and exhibit different distortions on octahedral [FeO6]/[WO6] clusters. High resolution transmission electron microcopy revealed an oriented attachment mechanism for the growth of aggregated FeWO4 nanocrystals. Finally, we observed that the photoluminescence properties of these nanocrystals are affected by partial preferential orientation in the (011) plane and distortions on [FeO6]/[WO6] clusters.

Structural Refinement and Photoluminescence Properties of MnWO4 Nanorods Obtained by Microwave-Hydrothermal Synthesis

Manganese tungstate (MnWO4) nanorods were prepared at room temperature by the co-precipitation method and synthesized after processing in a microwave-hydrothermal (MH) system at 140 degrees C for 6-96 min. These nanorods were structurally characterized by X-ray diffraction (XRD), Rietveld refinements and Fourier transform (FT)-Raman spectroscopy. The growth direction, shape and average size distribution of nanorods were observed by means of transmission electron microscopy (TEM) and high resolution TEM (HR-TEM). The optical properties of the nanorods were investigated by ultraviolet visible (UV-vis) absorption and photoluminescence (PL) measurements. XRD patterns, Rietveld refinement data and FT-Raman spectroscopy indicate that the MnWO4 precipitate is not a single phase structure while the nanorods synthesized by MH processing have a wolframite-type monoclinic structure without deleterious phases. FT-Raman spectra exhibited the presence of 17 Raman-active modes from 50 to 1,000 cm(-1). TEM and HR-TEM micrographs indicated that the nanorods are aggregated due to surface energy by Van der Waals forces and grow along the [100] direction. UV-vis absorption measurements confirmed non-linear values for the optical band gap (from 3.2 to 2.72 eV), which increased as the MH processing time increased. The structural characterizations indicated that the presence of defects in the MnWO4 precipitate promotes a significant contribution to maximum PL emission, while MnWO4 nanorods obtained by MH processing decrease the PL emission due to the reduction of defects in the lattice.

beta-ZnMoO4 microcrystals synthesized by the surfactant-assisted hydrothermal method: Growth process and photoluminescence properties

In this communication, we investigate the effect of different surfactants: cetyltrimethylammonium bromide (CTAB), sodium dodecyl sulfate (SDS) and polyvinylpyrrolidone (PVP-K40) on the growth process of zinc molybdate (beta-ZnMoO4) microcrystals synthesized under hydrothermal conditions at 140 degrees C for 8 h. These microcrystals were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and photoluminescence (PL) measurements. XRD patterns proved that these crystals are monophasic and present a wolframite-type monoclinic structure. FE-SEM images revealed that the surfactants modified the crystal shapes, suggesting the occurrence of distinct crystal growth processes. The CTAB cationic surfactant promotes the hindrance of small nuclei that leads to the formation of rectangle-like crystals, SDS anionic surfactant induces a growth of irregular hexagons with several porous due to considerable size effect of counter-ions on the crystal facets, PVP-K40 non-ionic surfactant allows a reduction in size and thickness of plate-like crystals, while without surfactants have the formation of irregular plate-like crystals. Finally, the PL properties of beta-ZnMoO4 microcrystals were explained by means of different shape/size, surface defects and order-disorder into lattice. (C) 2011 Elsevier B.V. All rights reserved.

Minerale der Molybdänitlagerstätte am Alpjuhorn im Baltschiedertal (VS)

Im Zuge einer Masterarbeit an der Universität Bern und am Naturhistorischen Museum der Burger- gemeinde Bern wurde das Molybdänitvorkommen am Alpjuhorn im Baltschiedertal untersucht. Neben Molybdänit wurden auch Scheelit, Ilmenit, Galenit, Ferberit und die Sekundärmineralien Ferrimolybdit und Powellit gefunden. Speziell am Galenit des Alpjuhorns ist, dass er eine oktaedrische Spaltbar- keit aufweist. Das Auftreten von Ferberit ist insofern erwähnenswert, da aus der Schweiz nur wenige Funde von Mineralien der Wolframit-Reihe (Ferberit- Hübnerit) bekannt sind.

Microtermometría, direcciones de flujo hidrotermal y metalogenia del yacimiento de tungsteno de Pasto Bueno (Ancash, Perú)

El yacimiento de Pasto Bueno se localiza en el extremo nordeste del Batolito de la Cordillera Blanca, comprende diversas vetas, generalmente subverticales, asociadas al stock cuarzomonzonitico de Consuzo, datado como Terciario Superior, que intruye a las pizarras de la fm. Chicama y cuarcitas de la fm. Chimu. Las principales vetas discurren con direccion N-S cortando al stock, aunque tambien existen sistemas NE-SW asi como NW-SE encajados sobre las rocas metamorficas. La mineralogia de mena reconocida comprende wolframita (hubnerita), tetraedrita/tenantita, esfalerita y galena, en una ganga de cuarzo, fluorita, sericita, pirita y carbonatos, ademas de molibdenita, calcopirita, bornita, arsenopirita, enargita (luzonita), stolzita, scheelita, zinnwaldita, topacio, tungstita y arsenico nativo. Estudios previos han caracterizado Pasto Bueno como un yacimiento con una gran componente de greisen, con una evolucion de las vetas desde un episodio temprano esteril de 400 oC, depositando la mineralizacion economica en torno a los 220-250 oC y con un evento postumo de 175-220 oC rico en CO2. La precipitacion de la wolframita se produjo a partir de un fluido netamente hidrotermal, sin embargo, dicha precipitacion estuvo controlada por el aporte al sistema de aguas externas meteoricas y/o metamorficas. El trabajo llevado a cabo ha consistido en la realizacion de un estudio microtermometrico de las 3 principales estructuras del distrito: Consuelo, Alonso-Fenix y Chabuca, para caracterizar la evolucion del fluido mineralizador desde el stock (veta Consuelo) hacia las rocas metasedimentarias de las fm. Chicama y Chimu (manto Alonso-Fenix y veta Chabuca). Para ello se realizo un muestreo sobre el evento principal de mineralizacion. Dichas muestras se sometieron a un estudio petrografico de lamina gruesa para seleccionar las muestras optimas para el posterior estudio microtermometrico. Previamente a la obtencion de las medidas de temperatura de fusion del hielo (criotermometria) y de homogenizacion del fluido; se realizo un estudio de petrografia de inclusiones fluidas para caracterizarlas y seleccionar las representativas. La interpretacion de los resultados ha permitido confirmar la existencia de un episodio previo de alta temperatura, superior a 282 oC y un evento mineralizador con temperaturas en torno a los 200-240 oC. Sin embargo, las salinidades obtenidas son mucho menores que las previamente publicadas, en torno al 5 % peso eq. NaCl, frente a 11-17 % peso eq. NaCl. Tambien se ha observado un fluido postumo rico en CO2, pero de temperatura superior, en torno a los 270 oC. Los gradientes isotermicos muestran dos focos para dichos fluidos hidrotermales: el primero asociado al stock en la veta Consuelo, y el segundo en la veta Chabuca, asociado a la zona de cabalgamiento de las pizarras de la fm. Chicama sobre las cuarcitas de la fm. Chimu. Este segundo foco puede corresponder con los aportes externos de aguas metamorficas. Para finalizar, se dan una serie de pautas para guiar las futuras exploraciones en el yacimiento. ABSTRACT The Pasto Bueno deposit is located at the northeastern end of the Cordillera Blanca Batholith. It comprises several veins, generally subvertical, associated with the quartz-monzonite stock of Consuzo, dated as Tertiary, which intrudes the Chicama fm. slates and the Chimu fm. quartzites. The main veins trend N-S cutting the stock, although there are also NE-SW and NWSE systems, hosted by the metamorphic rocks. The ore mineralogy comprises wolframite (hubnerite), tetrahedrite/tennantite, sphalerite and galena in a gangue of quartz, fluorite, sericite, pyrite and carbonates, and minor molybdenite, chalcopyrite, bornite, arsenopyrite, enargite (luzonite), stolzite, scheelite, zinnwaldite, topaz, tungstite and native arsenic. Previous studies have characterized Pasto Bueno as a deposit with a large component of greisen, with an evolution of the veins from an early barren 400 oC event , followed by economic mineralization of about 220-250 °C and a late event of 175 -220 oC rich in CO2. Wolframite precipitation occurred from a purely hydrothermal fluid; however, this precipitation was controlled by an external flux of meteoric and/or metamorphic waters. Microthermometric studies of the 3 main structures of the district (Consuelo, Alonso-Fenix and Chabuca veins) have been carried out to depict the evolution of the mineralizing fluid coming from the stock (Consuelo vein) into the metasedimentary rocks of the Chimu and Chicama fm. (Alonso-Fenix and Chabuca veins). The sampling was performed over the main event of mineralization. These samples were subject to a quick plate petrography study in order to select the optimal samples for further microthermometry studies. Before the freezing/heating measures, a fluid inclusion petrography study was done to characterize and select the representative F.I. Interpretation of results has confirmed the existence of a previous episode of higher temperature, over 282 °C, and a mineralizing event with temperatures of about 200-240 °C. However, obtained salinities, about 5 wt% NaCl equivalents, are much lower than those previously reported, about 11-17 wt% NaCl equivalents. A last fluid, rich in CO2, but of higher temperature, about 270 oC, has been characterized. Isothermal gradients show two foci for the hydrothermal fluids: the first one associated to the Consuzo stock as shown in the Consuelo vein, and the second one related to the thrust fault which places the Chicama fm. slates over the Chimu fm. quartzites in the Chabuca vein area. This second focus may correspond to an external input of metamorphic waters. Finally, some guidelines have been given to guide future explorations.