Molecular weight changes and scission and crosslinking in poly(dimethyl siloxane) on gamma radiolysis

The molecular weight changes which occur on the gamma -radiolysis of poly(dimethyl siloxane) under vacuum between 77 and 373 K and in air at 303 K have been investigated using triple detection GPC to obtain the complete molecular weight distributions for the irradiated samples and to determine the number and weight average molecular weights. The results have been interpreted in terms of the relative yields of scission and crosslinking. The total yields for crosslinking predominate over those for scission at all the temperatures investigated for radiolysis under vacuum. Based on a solid-state Si-29 NMR analysis of PDMS irradiated under vacuum at 303 K, which yielded a value of G(Y) of 1.70, the values of G(S) = 1.15 +/-0.2 and G(H) = 1.45 +/-0.2 were obtained for radiolysis under vacuum at 303 K. For radiolysis in air at 303 K, crosslinking was also predominant, but the nett yield of crosslinking was much less than that observed for radiolysis under vacuum. Under the conditions of the radiolysis in air at 303 K, because of the low solubility of oxygen in PDMS, it is likely that the radiation chemistry is limited by oxygen diffusion. (C) 2001 Elsevier Science Ltd. All rights reserved.

Modeling the molecular weight distribution of block copolymer formation in a reversible addition-fragmentation chain transfer mediated living radical polymerization

Block copolymers have become an integral part of the preparation of complex architectures through self-assembly. The use of reversible addition-fragmentation chain transfer (RAFT) allows blocks ranging from functional to nonfunctional polymers to be made with predictable molecular weight distributions. This article models block formation by varying many of the kinetic parameters. The simulations provide insight into the overall polydispersities (PDIs) that will be obtained when the chain-transfer constants in the main equilibrium steps are varied from 100 to 0.5. When the first dormant block [polymer-S-C(Z)=S] has a PDI of 1 and the second propagating radical has a low reactivity to the RAFT moiety, the overall PDI will be greater than 1 and dependent on the weight fraction of each block. When the first block has a PDI of 2 and the second propagating radical has a low reactivity to the RAFT moiety, the PDI will decrease to around 1.5 because of random coupling of two broad distributions. It is also shown how we can in principle use only one RAFT agent to obtain block copolymers with any desired molecular weight distribution. We can accomplish this by maintaining the monomer concentration at a constant level in the reactor over the course of the reaction. (c) 2005 Wiley Periodicals, Inc.

Design strategies for controlling the molecular weight and rate using reversible addition-fragmentation chain transfer mediated living radical polymerization

Living radical polymerization has allowed complex polymer architectures to be synthesized in bulk, solution, and water. The most versatile of these techniques is reversible addition-fragmentation chain transfer (RAFT), which allows a wide range of functional and nonfunctional polymers to be made with predictable molecular weight distributions (MWDs), ranging from very narrow to quite broad. The great complexity of the RAFT mechanism and how the kinetic parameters affect the rate of polymerization and MWD are not obvious. Therefore, the aim of this article is to provide useful insights into the important kinetic parameters that control the rate of polymerization and the evolution of the MWD with conversion. We discuss how a change in the chain-transfer constant can affect the evolution of the MWD. It is shown how we can, in principle, use only one RAFT agent to obtain a poly-mer with any MWD. Retardation and inhibition are discussed in terms of (1) the leaving R group reactivity and (2) the intermediate radical termination model versus the slow fragmentation model. (c) 2005 Wiley Periodicals, Inc.

On the Weight Distribution of the Coset Leaders of Constacyclic Codes

Constacyclic codes with one and the same generator polynomial and distinct length are considered. We give a generalization of the previous result of the first author [4] for constacyclic codes. Suitable maps between vector spaces determined by the lengths of the codes are applied. It is proven that the weight distributions of the coset leaders don’t depend on the word length, but on generator polynomials only. In particular, we prove that every constacyclic code has the same weight distribution of the coset leaders as a suitable cyclic code.

Calix[4]arene-carbazole-containing polymers: synthesis and properties

New highly fluorescent calix[4]arene-containing phenylene-alt-ethynylene-3,6- and 2,7-carbazolylene polymers (CALIX-PPE-CBZs) have been synthesized for the first time and their photophysical properties evaluated. Both polymers were obtained in good isolated yields (70-84%), having M-w ranging from 7660-26,700 g mol(-1). It was found that the diethynyl substitution (3,6- or 2,7-) pattern on the carbazole monomers markedly influences the degree of polymerization. The amorphous yellow polymers are freely soluble in several nonprotic organic solvents and have excellent film forming abilities. TG/DSC analysis evidences similar thermal behaviors for both polymers despite their quite different molecular weight distributions and main-chain connectivities (T-g, in the range 83-95 degrees C and decomposition onsets around 270 degrees C). The different conjugation lengths attained by the two polymers dictates much of their photophysical properties. Thus, whereas the fully conjugated CALIX-PPE-2,7-CBZ has its emission maximum at 430 nm (E-g = 2.84 eV; Phi(F) = 0.62, CHCl3), the 3,6-linked counterpart (CALIX-PPE-3,6-CBZ) fluoresces at 403 nm with a significant lower quantum yield (E-g = 3.06 eV; Phi(F) = 0.31, CHCl3). The optical properties of both polymers are predominantly governed by the intrachain electronic properties of the conjugated backbones owing to the presence of calix[4]arenes along the polymer chain which disfavor significant interchain interactions, either in fluid- or solid-state.

Modification d'acides biliaires à l'aide de polymères pour en moduler les propriétés d'agrégation

Les polymères amphiphiles sont largement utilisés pour les applications biomédicales et pharmaceutiques. Afin d’améliorer les chances de biocompatibilité des nouveaux polymères que nous voulons développer, nous avons utilisé des composés naturels, les acides biliaires, comme produits de départ dans la synthèse de ces polymères. De nouveaux polymères anioniques amphiphiles dérivés de l’acide cholique ont été préparés par polymérisation radicalaire par transfert d’atomes. Par un contrôle rigoureux des conditions de polymérisation, des bras de poly(acide acrylique) de différentes longueurs ont été greffés sur le squelette de l’acide cholique. L’architecture moléculaire des polymères a été étudiée par spectroscopie 1H RMN et par spectrométrie de masse. Ces polymères en étoile formés par l’acide biliaire modifié sont capables de s’agréger dans l’eau même si les groupements hydroxyles ont été remplacés par des segments plus volumineux. Il a été observé que les liaisons ester entre le polymère et le cœur d’acide cholique sont sensibles à l’hydrolyse en solution aqueuse. Pour remédier au problème de stabilité en solution aqueuse et pour avoir, en même temps, des bras hydrophiles non ioniques et biocompatibles, de l’oxyde d’éthylène a été polymérisé sur l’acide cholique par polymérisation anionique. Les liaisons éther formées entre le polymère et les groupements hydroxyles de l’acide biliaire sont plus stables que les liaisons ester sur le polymère de poly(acide acrylique). Les conditions de réaction de la polymérisation anionique ont été optimisées et ont donné des polymères aux architectures et aux masses molaires contrôlées. Les nouveaux polymères forment des agrégats sphériques tel qu’observé par microscopie électronique à transmission avec des échantillons préparés par la méthode de fracture à froid. Leur morphologie est différente de celle des agrégats cylindriques formés par les acides biliaires. Avec la méthode optimisée pour la polymérisation anionique, l’éther d’allyle et glycidyle a été polymérisé sur un dérivé d’acide cholique, suivi par une thiolation des liaisons doubles pour introduire l’amine ou l’acide sur la chaîne polymère. Cette addition radicalaire est efficace à plus de 90%. Les polymères qui en résultent sont solubles dans l’eau et s’agrègent à une certaine concentration critique. Il est particulièrement intéressant d’observer la thermosensibilité des polymères ayant des groupements amine, laquelle peut être modulée en acétylant partiellement les amines, donnant des points nuages entre 15 et 48°C.

The development of organized structures in polyethylene crystallized from a sheared melt, analyzed by WAXS and TEM

The development of global orientation and morphological features in linear polyethylene crystallizing from a sheared melt are studied using in-situ time-resolving wide angle X-ray scattering (WAXS) and ex-situ transmission electron microscopy. It is found that samples subjected to a shear rate above a critical value of ~1s-1 result in macroscopically oriented structures in the crystallized sample. This critical shear rate appears to be independent of the differences in molecular weight distribution of the samples studied although the morphologies which develop are sensitive to quite small differences in molecular weight distributions. The presence of shish kebabs in the morphology is shown to differ markedly according to variations in the upper molecular weight fraction of the molecular weight distribution, even though the resulting global orientation does not. The WAXS also reveals that areas which evidence no row nucleated structures still realize high degrees of molecular orientation. It is proposed that the formation of shish kebab or lamellar morphologies in these samples is dependent on the critical density of contiguous elongated crystallization nuclei rather than any specific global criteria.

Some structural and physicochemical characteristics of tuber and root starches

Starches from six different species (cassava, arrowroot, sweet potato, yam, canna and ginger) were isolated and some structural and physicochemical characteristics analysed and correlated. Phosphorous and amylose contents were determined using a colorimetric method and measuring iodine affinity, respectively. Molecular weight distributions of starches were analysed by Sepharose CL 2B. Granular shape and size distribution were performed using an image analyser system attached to a light microscope. Swelling power was determined at 60, 70, 80 and 90 degrees C. Pasting and thermal properties were measured using a rapid viscoanalyser, and a differential scanning calorimeter, respectively. Phosphorous content varied from 0.007 to 0.031% for cassava and canna starches, respectively. Yam, canna and ginger starches displayed higher amylose contents (32.6, 31.7 and 26.5%, respectively) than cassava, arrowroot and sweet potato starches (19.8, 20.8 and 22.6%, respectively). These last three starches displayed amylose molecules of higher molecular weight than those shown for yam, canna and ginger starches. Canna starch showed higher proportions of longer branch chains of amylopectin than others starches. The size and shape of granules were quite variable among all starches and the average size of granules varied from 13.9 to 42.3 mu m for sweet potato and canna, respectively. Swelling power, pasting, and thermal properties were affected by structural characteristics of the starches.

Plataforma para medição de forças na região plantar de pacientes normais e hemiplégicos

This work describes an electronic system implementation with two force plates, 24 load cells with strain gages, signal conditioning circuit, interfacing circuit and data acquisition system, designed for measuring plantar force distribution in patients. The system presented linear response, low hysteresis, with determination coefficient of 0.9997, precision better than 0,84% and resolution less than 0.5 N. The Measurements are presented on a computer screen and easier visualization to specialists, mainly physicians, physiotherapists and occupational therapists. Using the system, the distribution of weight in the plantar region of 100 normal subjects and 10 hemiplegic patients was investigated. There were determined the relationship between weight distribution on the right and left forefoot, hemiplegic patients and normal patients, with the implemented system. © 2013 Springer.

Medição da descarga de peso de indivíduos hemiplégicos e não hemiplégicos utilizando uma nova plataforma de força

Pós-graduação em Engenharia Elétrica - FEIS

Características estruturais e físico-químicas de amidos obtidos de diferentes fontes botânicas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Enhanced Polymer Grafting from Multiwalled Carbon Nanotubes through Living Anionic Surface-Initiated Polymerization

Anionic surface-initiated polymerization of ethylene oxide and styrene has been performed using multiwalled carbon nanotubes (MWNTs) functionalized with anionic initiators. The surface of MWNTs was modified via covalent attachment of precursor anions such as 4-hydroxyethyl benzocyclobutene (BCBEO) and 1-benzocyclobutene-1′-phenylethylene (BCB-PE) through Diels-Alder cycloaddition at 235 °C. Surface-functionalized MWNTs-g-(BCB-EO) n and MWNTs-g-(BCB-PE) n with 23 and 54 wt % precursor initiators, respectively, were used for the polymerizations. Alkoxide anion on the surface of MWNTs-g-(BCB-EO) n was generated through reaction with potassium triphenylmethane for the polymerization of ethylene oxide in tetrahydrofuran and phenyl substituted alkyllithium was generated from the surface of MWNTs-g-(BCB-PE) n using sec-butyllithium for the polymerization of styrene in benzene. In both cases, the initiation was found to be very slow because of the heterogeneous reaction medium. However, the MWNTs gradually dispersed in the reaction medium during the polymerization. A pale green color was noticed in the case of ethylene oxide polymerization and the color of initiator as well as the propagating anions was not discernible visually in styrene polymerization. Polymer grafted nanocomposites, MWNTs-g-(BCB-PEO) n and MWNTs-g-(BCB-PS) n containing a very high percentage of hairy polymer with a small fraction of MWNTs (<1 wt %) were obtained. The conversion of ethylene oxide and the weight percent of PEO on the surface of the MWNTs increased with increasing reaction time indicating a controlled polymerization. The polymer-grafted MWNTs were characterized using FTIR, 1H NMR, Raman spectroscopy, differential scanning calorimetry, thermogravimetric analysis, and transmission electron microscopy (TEM). Size exclusion chromatography of the polymer grafted MWNTs revealed broad molecular weight distributions (1.3 < Mw/Mn < 1.8) indicating the presence of different sizes of polymer nanocomposites. The TEM images showed the presence of thick layers of polymer up to 30 nm around the MWNTs. The living nature of the growing polystyryllithium was used to produce diblock copolymer grafts using sequential polymerization of isoprene on the surface of MWNTs.

Matrix-Assisted Laser Desorption/Ionization Time-of-Flight Mass Spectrometry Characterization of Primary Amine End-Functionalized Polystyrene and Poly(methyl methacrylate) Synthesized by Living Anionic Polymerization Techniques

The reaction of living anionic polymers with 2,2,5,5-tetramethyl-1-(3-bromopropyl)-1-aza-2,5- disilacyclopentane (1) was investigated using coupled thin layer chromatography and matrix-assisted laser desorption/ionization time-of-flight mass spectrometry. Structures of byproducts as well as the major product were determined. The anionic initiator having a protected primary amine functional group, 2,2,5,5-tetramethyl- 1-(3-lithiopropyl)-1-aza-2,5-disilacyclopentane (2), was synthesized using all-glass high-vacuum techniques, which allows the long-term stability of this initiator to be maintained. The use of 2 in the preparation of well-defined aliphatic primary amine R-end-functionalized polystyrene and poly(methyl methacrylate) was investigated. Primary amino R-end-functionalized poly(methyl methacrylate) can be obtained near-quantitatively by reacting 2 with 1,1-diphenylethylene in tetrahydrofuran at room temperature prior to polymerizing methyl methacrylate at -78 °C. When 2 is used to initiate styrene at room temperature in benzene, an additive such as N,N,N',N'- tetramethylethylenediamine is necessary to activate the polymerization. However, although the resulting polymers have narrow molecular weight distributions and well-controlled molecular weights, our mass spectra data suggest that the yield of primary amine α-end-functionalized polystyrene from these syntheses is very low. The majority of the products are methyl α-end-functionalized polystyrene.

Well-Defined Poly(4-vinylbenzocyclobutene): Synthesis by Living Anionic Polymerization and Characterization

Living anionic polymerization of 4-vinylbenzocylobutene was performed in benzene at room temperature using sec-butyllithium as the initiator. Results of the kinetic studies indicated the termination- and transfer-free nature of the polymerization. Homopolymers with predictable molecular weights and narrow molecular weight distributions were produced, excluding the interference of the cyclobutene rings during initiation and propagation. Thermogravimetric analysis of poly(4-vinylbenzocyclobutene) in air showed a small weight gain at ~200 °C, a rapid decomposition at ~455 °C, and a gradual decomposition at ~566 °C. This behavior was attributed to the formation of radicals from the pendent benzocyclobutene functionality through o-quinodimethane intermediates and simultaneous decomposition/cross-linking reactions at high temperature. The living nature of the polymerization was also examined via sequential copolymerization with butadiene to form diblock copolymers.

Überkritisches Kohlendioxid als Reaktionsmedium für die Dispersionspolymerisation

Überkritisches Kohlendioxid (CO2) ist für die Polymerisation von besonderem Interesse. Die Dispersionspolymerisation von N-Vinylpyrrolidon (VP) wurde mit Polystyrol-Polydimethylsiloxan Diblockcopolymeren (PS-b-PDMS) in diesem Medium durchgeführt. Hierfür wurde ein neues Hochdrucklabor eingerichtet, eine Sichtzelle und eine neuartige Lichtstreuzelle konstruiert. Für die Durchführung von Lichtstreuexperimenten wurde der Brechungs-index von CO2 bis zu hohen Dichten an einer Reflexionsapparatur bestimmt. Mittels dynamischen Lichtstreumessungen an Polydimethylsiloxan (PDMS) in überkritischem CO2 wurden unter den untersuchten Bedingungen ein Radius bestimmt, wie er für ungestörte Knäueldimensionen erwartet wurde. Das PS-b-PDMS wurde mittels anionischer Polymerisation mit verschiedenen Blocklängen und sehr engen Molekulargewichtsverteilungen synthetisiert. Das Phasenverhalten von PS-b-PDMS wurde in überkritischem CO2 visuell und in einer VP/CO2-Mischung mittels Turbidimetrie untersucht. Das Monomer wirkt als Co-Solvens für den PDMS-Block des Stabilisators. Bei einer Konzentration von ca. 1 Gew.-% PS-b-PDMS (pro Monomer) in CO2 bei 38 MPa und 80°C wurden sphärische ca. 1µm große PVP-Partikeln synthetisiert. PS-b-PDMS ist unter diesen Bedingungen ein geeigneter Stabilisator für die Polymerisation von VP in überkritischem CO2. Bei Konzentrationen von mehr als ca. 5 Gew.-% PS-b-PDMS wurden agglomerierte Partikeln beobachtet. Die Kinetik der Partikelentstehung wurde turbidimetrisch untersucht. Bereits in der frühen Phase der Polymerisation wurde eine anwachsende Partikelgröße gefunden.