Development and improvement of warm-mix asphalt technology

Traditionally, asphalt mixtures were produced at high temperatures (between 150°C to 180°C) and therefore often referred to as Hot Mix Asphalt (HMA). Recently, a new technology named Warm Mix Asphalt (WMA) was developed in Europe that allows HMA to be produced at a lower temperature. Over years of research efforts, a few WMA technologies were introduced including the foaming method using Aspha-min® and Advera® WMA; organic additives such as Sasobit® and Asphaltan B®; and chemical packages such as Evotherm® and Cecabase RT®. Benefits were found when lower temperatures were used to produce asphalt mixtures, especially when it comes to environmental and energy savings. Even though WMA has shown promising results in energy savings and emission reduction, however, only limited studies and laboratory tests have been conducted to date. The objectives of this project are to 1) develop a mix design framework for WMA by evaluating its mechanical properties; 2) evaluate performance of WMA containing high percentages of recycled asphalt material; and 3) evaluate the moisture sensitivity in WMA. The test results show that most of the WMA has higher fatigue life and TSR which indicated WMA has better fatigue cracking and moisture damage resistant; however, the rutting potential of most of the WMA tested were higher than the control HMA. A recommended WMA mix design framework was developed as well. The WMA design framework was presented in this study to provide contractors, and government agencies successfully design WMA. Mixtures containing high RAP and RAS were studied as well and the overall results show that WMA technology allows the mixture containing high RAP content and RAS to be produced at lower temperature (up to 35°C lower) without significantly affect the performance of asphalt mixture in terms of rutting, fatigue and moisture susceptibility. Lastly, the study also found that by introducing the hydrated lime in the WMA, all mixtures modified by the hydrated lime passed the minimum requirement of 0.80. This indicated that, the moisture susceptibility of the WMA can be improved by adding the hydrated lime.

Study of the effect of four warm mix asphalt additives on bitumen modified with 15% crumb rubber

Due to a growing concern over global warming, the bituminous mixture industry is making a constant effort to diminish its emissions by reducing manufacturing and installation temperatures without compromising the mechanical properties of the bituminous mixtures. The use of mixtures with tyre rubber has demonstrated that these mixtures can be economical and ecological and that they improve the behaviour of the pavements. However, bituminous mixtures with a high rubber content present one major drawback: they require higher mixing and installation temperatures due to the elevated viscosity caused by the high rubber content and thus they produce larger amounts of greenhouse gas emissions than conventional bituminous mixtures. This article presents a study of the effect of four viscosity-reducing additives (Sasobit®, Asphaltan A®, Asphaltan B® and Licomont BS 100®) on a bitumen modified with 15% rubber. The results of this study indicate that these additives successfully reduce viscosity, increase the softening temperature and reduce penetration. However, they do not have a clear effect on the test for elastic recovery and ductility at 25 °C.

Asphalt rubber mixtures with warm mix asphalt additives

En los últimos años, debido a la creciente preocupación por el calentamiento global y el cambio climático, uno de los retos más importantes a los que se enfrenta nuestra sociedad es el uso eficiente y económico de energía así como la necesidad correspondiente de reducir los gases de efecto invernadero (GEI). Las tecnologías de mezclas semicalientes se han convertido en un nuevo e importante tema de investigación en el campo de los materiales para pavimentos ya que ofrece una solución potencial para la reducción del consumo energético y las emisiones de GEI durante la producción y puesta en obra de las mezclas bituminosas. Por otro lado, los pavimentos que contienen polvo de caucho procedente de neumático fuera de uso, al hacer uso productos de desecho, ahorran energía y recursos naturales. Estos pavimentos ofrecen una resistencia mejorada a la formación de roderas, a la fatiga y a la fisuración térmica, reducen los costes de mantenimiento y el ruido del tráfico así como prolongan la vida útil del pavimento. Sin embargo, estas mezclas presentan un importante inconveniente: la temperatura de fabricación se debe aumentar en comparación con las mezclas asfálticas convencionales, ya que la incorporación de caucho aumenta la viscosidad del ligante y, por lo tanto, se producen mayores cantidades de emisiones de GEI. En la presente Tesis, la tecnología de mezclas semicalientes con aditivos orgánicos (Sasobit, Asphaltan A, Asphaltan B, Licomont) se incorporó a la de betunes de alta viscosidad modificados con caucho (15% y 20% de caucho) con la finalidad de dar una solución a los inconvenientes de mezclas con caucho gracias a la utilización de aditivos reductores de la viscosidad. Para este fin, se estudió si sería posible obtener una producción más sostenible de mezclas con betunes de alto contenido en caucho sin afectar significativamente su nivel de rendimiento mecánico. La metodología aplicada para evaluar y comparar las características de las mezclas consistió en la realización de una serie de ensayos de laboratorio para betunes y mezclas con caucho y con aditivos de mezclas semicalientes y de un análisis del ciclo de vida híbrido de la producción de mezclas semicalientes teniendo en cuenta la papel del aditivo en la cadena de suministro con el fin de cuantificar con precisión los beneficios de esta tecnología. Los resultados del estudio indicaron que la incorporación de los aditivos permite reducir la viscosidad de los ligantes y, en consecuencia, las temperaturas de producción y de compactación de las mezclas. Por otro lado, aunque la adición de caucho mejoró significativamente el comportamiento mecánico de los ligantes a baja temperatura reduciendo la susceptibilidad al fenómeno de fisuración térmica, la adición de las ceras aumentó ligeramente la rigidez. Los resultados del estudio reológico mostraron que la adición de porcentajes crecientes de caucho mejoraban la resistencia del pavimento con respecto a la resistencia a la deformación permanente a altas temperaturas y a la fisuración térmica a bajas temperaturas. Además, se observó que los aditivos mejoran la resistencia a roderas y la elasticidad del pavimento al aumentar el módulo complejo a altas temperaturas y al disminuir del ángulo de fase. Por otra parte, el estudio reológico confirmó que los aditivos estudiados aumentan ligeramente la rigidez a bajas temperaturas. Los ensayos de fluencia llevados a cabo con el reómetro demostraron una vez más la mejora en la elasticidad y en la resistencia a la deformación permanente dada por la adición de las ceras. El estudio de mezclas con caucho y aditivos de mezclas semicalientes llevado a cabo demostró que las temperaturas de producción/compactación se pueden disminuir, que las mezclas no experimentarían escurrimiento, que los aditivos no cambian significativamente la resistencia conservada y que cumplen la sensibilidad al agua exigida. Además, los aditivos aumentaron el módulo de rigidez en algunos casos y mejoraron significativamente la resistencia a la deformación permanente. Asimismo, a excepción de uno de los aditivos, las mezclas con ceras tenían la misma o mayor resistencia a la fatiga en comparación con la mezcla control. Los resultados del análisis de ciclo de vida híbrido mostraron que la tecnología de mezclas semicalientes es capaz de ahorrar significativamente energía y reducir las emisiones de GEI, hasta un 18% y 20% respectivamente, en comparación con las mezclas de control. Sin embargo, en algunos de los casos estudiados, debido a la presencia de la cera, la temperatura de fabricación debe reducirse en un promedio de 8 ºC antes de que los beneficios de la reducción de emisiones y el consumo de combustible puedan ser obtenidos. Los principales sectores contribuyentes a los impactos ambientales generados en la fabricación de mezclas semicalientes fueron el sector de los combustibles, el de la minería y el de la construcción. Due to growing concerns over global warming and climate change in recent years, one of the most important challenges facing our society is the efficient and economic use of energy, and with it, the corresponding need to reduce greenhouse gas (GHG) emissions. The Warm Mix Asphalt (WMA) technology has become an important new research topic in the field of pavement materials as it offers a potential solution for the reduction of energy consumption and GHG emissions during the production and placement of asphalt mixtures. On the other hand, pavements containing crumb-rubber modified (CRM) binders save energy and natural resources by making use of waste products. These pavements offer an improved resistance to rutting, fatigue and thermal cracking; reduce traffic noise and maintenance costs and prolong pavement life. These mixtures, however, present one major drawback: the manufacturing temperature is higher compared to conventional asphalt mixtures as the rubber lends greater viscosity to the binder and, therefore, larger amounts of GHG emissions are produced. In this dissertation the WMA technology with organic additives (Sasobit, Asphaltan A, Asphaltan B and Licomont) was applied to CRM binders (15% and 20% of rubber) in order to offer a solution to the drawbacks of asphalt rubber (AR) mixtures thanks to the use of fluidifying additives. For this purpose, this study sought to determine if a more sustainable production of AR mixtures could be obtained without significantly affecting their level of mechanical performance. The methodology applied in order to evaluate and compare the performance of the mixtures consisted of carrying out several laboratory tests for the CRM binders and AR mixtures with WMA additives (AR-WMA mixtures) and a hybrid input-output-based life cycle assessment (hLCA) of the production of WMA. The results of the study indicated that the incorporation of the organic additives were able to reduce the viscosity of the binders and, consequently, the production and compaction temperatures. On the other hand, although the addition of rubber significantly improved the mechanical behaviour of the binders at low temperatures reducing the susceptibility to thermal cracking phenomena, the addition of the waxes slightly increased the stiffness. Master curves showed that the addition of increasing percentages of rubber improved the resistance of the pavement regarding both resistance to permanent deformation at high temperatures and thermal cracking at low temperatures. In addition, the waxes improved the rutting resistance and the elasticity as they increased the complex modulus at high temperatures and decreased the phase angle. Moreover, master curves also attest that the WMA additives studied increase the stiffness at low temperatures. The creep tests carried out proved once again the improvement in the elasticity and in the resistance to permanent deformation given by the addition of the waxes. The AR-WMA mixtures studied have shown that the production/compaction temperatures can be decreased, that the mixtures would not experience binder drainage, that the additives did not significantly change the retained resistance and fulfilled the water sensitivity required. Furthermore, the additives increased the stiffness modulus in some cases and significantly improved the permanent deformation resistance. Except for one of the additives, the waxes had the same or higher fatigue resistance compared to the control mixture. The results of the hLCA demonstrated that the WMA technology is able to significantly save energy and reduce GHG emissions, up to 18% and 20%, respectively, compared to the control mixtures. However, in some of the case studies, due to the presence of wax, the manufacturing temperature at the asphalt plant must be reduced by an average of 8ºC before the benefits of reduced emissions and fuel usage can be obtained. The results regarding the overall impacts generated using a detailed production layer decomposition indicated that fuel, mining and construction sectors are the main contributors to the environmental impacts of manufacturing WMA mixtures.

Improved methodology to evaluate fracture properties of warm-mix asphalt using overlay test

This study developed a reliable and repeatable methodology to evaluate the fracture properties of asphalt mixtures with an overlay test (OT). In the proposed methodology, first, a two-step OT protocol was used to characterize the undamaged and damaged behaviors of asphalt mixtures. Second, a new methodology combining the mechanical analysis of viscoelastic force equilibrium in the OT specimen and finite element simulations was used to determine the undamaged properties and crack growth function of asphalt mixtures. Third, a modified Paris's law replacing the stress intensity factor by the pseudo J-integral was employed to characterize the fracture behavior of asphalt mixtures. Theoretical equations were derived to calculate the parameters A and n (defined as the fracture properties) in the modified Paris's law. The study used a detailed example to calculate A and n from the OT data. The proposed methodology was successfully applied to evaluate the impact of warm-mix asphalt (WMA) technologies on fracture properties. The results of the tested specimens showed that Evotherm WMA technology slightly improved the cracking resistance of asphalt mixtures, while foaming WMA technology provided comparable fracture properties. In addition, the study found that A decreased with the increase in n in general. A linear relationship between 2log(A) and n was established.

Comparison of the n-Alkanes and Polycyclic Aromatic Hydrocarbons Concentrations in the Atmosphere during the Preparation of Warm and Hot Mixtures Asphalt for Pavements

Asphalt binder is used in the production of hot mixes asphalt (HMA) for paving and, due to the high temperatures used, generates fumes thatcontainn-alkanes and polycyclic aromatic hydrocarbons (PAH). Asphalt mixes prepared at lower temperatures, such as warm mixes asphalt (WMA), may contribute to reduce the emissions of those compounds and save energy. This paper investigatesn-alkanes and PAH in the total suspended particles during the preparation of WMA, in comparison with HMA, in laboratory. The results showed that the n-alkanes of the WMA and HMA presented C-max at n-C-26 and n-C-28, respectively; also, the total content of n-alkanes was higher for the HMA than forthe WMA. Besides, benzo[b]fluoranthene and benzo[a]anthracene were the major PAH in the WMA, while the higher temperatures of the HMA were observed to volatilize all larger PAH, demonstrating higher potential of inhalation exposure.

Comparison of the n-alkanes and polycyclic aromatic hydrocarbons concentrations in the atmosphere during the preparation of warm and hot mixtures asphalt for pavements

O asfalto é utilizado na produção de misturas asfálticas a quente (HMA) para a pavimentação e, devido às altas temperaturas empregadas, gera fumos que contêm n-alcanos e hidrocarbonetos policíclicos aromáticos (HPAs). As misturas asfálticas preparadas em temperaturas mais baixas, como as misturas asfálticas mornas (WMA), podem contribuir na redução das emissões daqueles compostos e economizar energia. Este trabalho investiga os n-alcanos e os HPAs nas partículas totais em suspensão durante a preparação de uma WMA, em comparação com uma HMA, em laboratório. Os resultados mostraram que os n-alcanos da WMA e da HMA apresentaram Cmáx no n-C26 e n-C28, respectivamente, e o teor de n-alcanos total foi maior na HMA do que na WMA. Ademais, verificou-se que o benzo[b]fluoranteno e benzo[a]antraceno constituíam os maiores HPAs na WMA, enquanto as temperaturas mais altas da HMA volatilizaram todos seus grandes HPAs, demonstrando maior potencial de exposição por inalação.

Performance evaluation of asphalt pavements using the Incremental-Recursive procedure of the Mechanistic-Empirical design software CalME

Il concetto di “sostenibilità” si riferisce allo sviluppo dei sistemi umani attraverso il più piccolo impatto possibile sul sistema ambientale. Le opere che si inseriscono bene nel contesto ambientale circostante e le pratiche che rispettano le risorse in maniera tale da permettere una crescita e uno sviluppo a lungo termine senza impattare sull’ambiente sono indispensabili in una società moderna. I progressi passati, presenti e futuri che hanno reso i conglomerati bituminosi materiali sostenibili dal punto di vista ambientale sono particolarmente importanti data la grande quantità di conglomerato usato annualmente in Europa e negli Stati Uniti. I produttori di bitume e di conglomerato bituminoso stanno sviluppando tecniche innovative per ridurre l’impatto ambientale senza compromettere le prestazioni meccaniche finali. Un conglomerato bituminoso ad “alta lavorabilità” (WMA), pur sviluppando le stesse caratteristiche meccaniche, richiede un temperatura di produzione minore rispetto a quella di un tradizionale conglomerato bituminoso a caldo (HMA). L’abbassamento della temperature di produzione riduce le emissioni nocive. Questo migliora le condizioni dei lavoratori ed è orientato verso uno sviluppo sostenibile. L’obbiettivo principale di questa tesi di laurea è quello di dimostrare il duplice valore sia dal punto di vista dell’eco-compatibilità sia dal punto di vista meccanico di questi conglomerati bituminosi ad “alta lavorabilità”. In particolare in questa tesi di laurea è stato studiato uno SMA ad “alta lavorabilità” (PGGWMA). L’uso di materiali a basso impatto ambientale è la prima fase verso un progetto ecocompatibile ma non può che essere il punto di partenza. L’approccio ecocompatibile deve essere esteso anche ai metodi di progetto e alla caratterizzazione di laboratorio dei materiali perché solo in questo modo è possibile ricavare le massime potenzialità dai materiali usati. Un’appropriata caratterizzazione del conglomerato bituminoso è fondamentale e necessaria per una realistica previsione delle performance di una pavimentazione stradale. La caratterizzazione volumetrica (Mix Design) e meccanica (Deformazioni Permanenti e Comportamento a fatica) di un conglomerato bituminoso è una fase importante. Inoltre, al fine di utilizzare correttamente i materiali, un metodo di progetto avanzato ed efficiente, come quello rappresentato da un approccio Empirico-Meccanicistico (ME), deve essere utilizzato. Una procedura di progetto Empirico-Meccanicistica consiste di un modello strutturale capace di prevedere gli stati di tensione e deformazione all’interno della pavimentazione sotto l’azione del traffico e in funzione delle condizioni atmosferiche e di modelli empirici, calibrati sul comportamento dei materiali, che collegano la risposta strutturale alle performance della pavimentazione. Nel 1996 in California, per poter effettivamente sfruttare i benefici dei continui progressi nel campo delle pavimentazioni stradali, fu iniziato un estensivo progetto di ricerca mirato allo sviluppo dei metodi di progetto Empirico - Meccanicistici per le pavimentazioni stradali. Il risultato finale fu la prima versione del software CalME che fornisce all’utente tre approcci diversi di l’analisi e progetto: un approccio Empirico, uno Empirico - Meccanicistico classico e un approccio Empirico - Meccanicistico Incrementale - Ricorsivo. Questo tesi di laurea si concentra sulla procedura Incrementale - Ricorsiva del software CalME, basata su modelli di danno per quanto riguarda la fatica e l’accumulo di deformazioni di taglio dai quali dipendono rispettivamente la fessurazione superficiale e le deformazioni permanenti nella pavimentazione. Tale procedura funziona per incrementi temporali successivi e, usando i risultati di ogni incremento temporale, ricorsivamente, come input dell’incremento temporale successivo, prevede le condizioni di una pavimentazione stradale per quanto riguarda il modulo complesso dei diversi strati, le fessurazioni superficiali dovute alla fatica, le deformazioni permanenti e la rugosità superficiale. Al fine di verificare le propreità meccaniche del PGGWMA e le reciproche relazioni in termini di danno a fatica e deformazioni permanenti tra strato superficiale e struttura della pavimentazione per fissate condizioni ambientali e di traffico, è stata usata la procedura Incrementale – Ricorsiva del software CalME. Il conglomerato bituminoso studiato (PGGWMA) è stato usato in una pavimentazione stradale come strato superficiale di 60 mm di spessore. Le performance della pavimentazione sono state confrontate a quelle della stessa pavimentazione in cui altri tipi di conglomerato bituminoso sono stati usati come strato superficiale. I tre tipi di conglomerato bituminoso usati come termini di paragone sono stati: un conglomerato bituminoso ad “alta lavorabilità” con granulometria “chiusa” non modificato (DGWMA), un conglomerato bituminoso modificato con polverino di gomma con granulometria “aperta” (GGRAC) e un conglomerato bituminoso non modificato con granulometria “chiusa” (DGAC). Nel Capitolo I è stato introdotto il problema del progetto ecocompatibile delle pavimentazioni stradali. I materiali a basso impatto ambientale come i conglomerati bituminosi ad “alta lavorabilità” e i conglomerati bituminosi modificati con polverino di gomma sono stati descritti in dettaglio. Inoltre è stata discussa l’importanza della caratterizzazione di laboratorio dei materiali e il valore di un metodo razionale di progetto delle pavimentazioni stradali. Nel Capitolo II sono stati descritti i diversi approcci progettuali utilizzabili con il CalME e in particolare è stata spiegata la procedura Incrementale – Ricorsiva. Nel Capitolo III sono state studiate le proprietà volumetriche e meccaniche del PGGWMA. Test di Fatica e di Deformazioni Permanenti, eseguiti rispettivamente con la macchina a fatica per flessione su quattro punti e il Simple Shear Test device (macchina di taglio semplice), sono stati effettuati su provini di conglomerato bituminoso e i risultati dei test sono stati riassunti. Attraverso questi dati di laboratorio, i parametri dei modelli della Master Curve, del danno a fatica e dell’accumulo di deformazioni di taglio usati nella procedura Incrementale – Ricorsiva del CalME sono stati valutati. Infine, nel Capitolo IV, sono stati presentati i risultati delle simulazioni di pavimentazioni stradali con diversi strati superficiali. Per ogni pavimentazione sono stati analizzati la fessurazione superficiale complessiva, le deformazioni permanenti complessive, il danno a fatica e la profondità delle deformazioni in ognuno degli stati legati.

Performance evaluation of low environmental impact asphalt concretes using the mechanistic empirical design method based on laboratory fatigue and permanent deformation models

The "sustainability" concept relates to the prolonging of human economic systems with as little detrimental impact on ecological systems as possible. Construction that exhibits good environmental stewardship and practices that conserve resources in a manner that allow growth and development to be sustained for the long-term without degrading the environment are indispensable in a developed society. Past, current and future advancements in asphalt as an environmentally sustainable paving material are especially important because the quantities of asphalt used annually in Europe as well as in the U.S. are large. The asphalt industry is still developing technological improvements that will reduce the environmental impact without affecting the final mechanical performance. Warm mix asphalt (WMA) is a type of asphalt mix requiring lower production temperatures compared to hot mix asphalt (HMA), while aiming to maintain the desired post construction properties of traditional HMA. Lowering the production temperature reduce the fuel usage and the production of emissions therefore and that improve conditions for workers and supports the sustainable development. Even the crumb-rubber modifier (CRM), with shredded automobile tires and used in the United States since the mid 1980s, has proven to be an environmentally friendly alternative to conventional asphalt pavement. Furthermore, the use of waste tires is not only relevant in an environmental aspect but also for the engineering properties of asphalt [Pennisi E., 1992]. This research project is aimed to demonstrate the dual value of these Asphalt Mixes in regards to the environmental and mechanical performance and to suggest a low environmental impact design procedure. In fact, the use of eco-friendly materials is the first phase towards an eco-compatible design but it cannot be the only step. The eco-compatible approach should be extended also to the design method and material characterization because only with these phases is it possible to exploit the maximum potential properties of the used materials. Appropriate asphalt concrete characterization is essential and vital for realistic performance prediction of asphalt concrete pavements. Volumetric (Mix design) and mechanical (Permanent deformation and Fatigue performance) properties are important factors to consider. Moreover, an advanced and efficient design method is necessary in order to correctly use the material. A design method such as a Mechanistic-Empirical approach, consisting of a structural model capable of predicting the state of stresses and strains within the pavement structure under the different traffic and environmental conditions, was the application of choice. In particular this study focus on the CalME and its Incremental-Recursive (I-R) procedure, based on damage models for fatigue and permanent shear strain related to the surface cracking and to the rutting respectively. It works in increments of time and, using the output from one increment, recursively, as input to the next increment, predicts the pavement conditions in terms of layer moduli, fatigue cracking, rutting and roughness. This software procedure was adopted in order to verify the mechanical properties of the study mixes and the reciprocal relationship between surface layer and pavement structure in terms of fatigue and permanent deformation with defined traffic and environmental conditions. The asphalt mixes studied were used in a pavement structure as surface layer of 60 mm thickness. The performance of the pavement was compared to the performance of the same pavement structure where different kinds of asphalt concrete were used as surface layer. In comparison to a conventional asphalt concrete, three eco-friendly materials, two warm mix asphalt and a rubberized asphalt concrete, were analyzed. The First Two Chapters summarize the necessary steps aimed to satisfy the sustainable pavement design procedure. In Chapter I the problem of asphalt pavement eco-compatible design was introduced. The low environmental impact materials such as the Warm Mix Asphalt and the Rubberized Asphalt Concrete were described in detail. In addition the value of a rational asphalt pavement design method was discussed. Chapter II underlines the importance of a deep laboratory characterization based on appropriate materials selection and performance evaluation. In Chapter III, CalME is introduced trough a specific explanation of the different equipped design approaches and specifically explaining the I-R procedure. In Chapter IV, the experimental program is presented with a explanation of test laboratory devices adopted. The Fatigue and Rutting performances of the study mixes are shown respectively in Chapter V and VI. Through these laboratory test data the CalME I-R models parameters for Master Curve, fatigue damage and permanent shear strain were evaluated. Lastly, in Chapter VII, the results of the asphalt pavement structures simulations with different surface layers were reported. For each pavement structure, the total surface cracking, the total rutting, the fatigue damage and the rutting depth in each bound layer were analyzed.

Investigation on performance characteristics of dense graded hot mix asphalt with RAP and Crumb Rubber

The use of recycled materials in asphalt mixtures such as reclaimed asphalt pavements (RAP) have become widely accepted as a replacement for virgin asphalt binder or virgin aggregates. In this study, the RAP content was 30%, and CR additives were blended with the soft unmodified binder by using dry processes. The objective of this study was to investigate and evaluate the engineering properties of dry method application of crumb rubber influences on reclaimed asphalt pavement (RAP) mixtures. To evaluate the effect of rubber-bitumen interaction on the mixture’s mechanical properties, a laboratory investigation has been conducted on a range of dense graded and 30% RAP by dry process crumb rubber modified (CRM) asphalt mixtures containing 0% (control), 1% crumb rubber by the total aggregate mass. The experimental program in this research include the binder extraction for estimating the amount of aged binder in the both fine and coarse RAP material. Before extracting the binder the RAP sieve analysis, have been done to provide the Black grading curve. In continue after the binder extraction the material sieved again to providing the white curve. The comparison of Black and White curve indicated that there is a remarkable difference between the aggregate grading even for the fine RAP. The experimental program was continued by fabricating 12 specimens in different 4 types of mixtures. For the first group no RAP, no rejuvenator and no crumb rubber were used. For the second group 30% of virgin aggregates substituted by RAP material and the third group was similar to the second group just with 0.01% rejuvenator. the forth group was the group, which in that the specimens contain RAP, rejuvenator and crumb rubber. Finally the specimens were tested for Indirect tensile strength. The results indicated that the addition of crumb rubber increased the optimum amount of binder in the mixture with 30% RAP.

Specifications for bituminous surface, open-graded aggregate type, subclass C-4 (Machine mix-asphalt and tar) : effective May 15, 1939 ...

Cover-title.

Using overlay test to evaluate fracture properties of field-aged asphalt concrete

Field material testing provides firsthand information on pavement conditions which are most helpful in evaluating performance and identifying preventive maintenance or overlay strategies. High variability of field asphalt concrete due to construction raises the demand for accuracy of the test. Accordingly, the objective of this study is to propose a reliable and repeatable methodology to evaluate the fracture properties of field-aged asphalt concrete using the overlay test (OT). The OT is selected because of its efficiency and feasibility for asphalt field cores with diverse dimensions. The fracture properties refer to the Paris’ law parameters based on the pseudo J-integral (A and n) because of the sound physical significance of the pseudo J-integral with respect to characterizing the cracking process. In order to determine A and n, a two-step OT protocol is designed to characterize the undamaged and damaged behaviors of asphalt field cores. To ensure the accuracy of determined undamaged and fracture properties, a new analysis method is then developed for data processing, which combines the finite element simulations and mechanical analysis of viscoelastic force equilibrium and evolution of pseudo displacement work in the OT specimen. Finally, theoretical equations are derived to calculate A and n directly from the OT test data. The accuracy of the determined fracture properties is verified. The proposed methodology is applied to a total of 27 asphalt field cores obtained from a field project in Texas, including the control Hot Mix Asphalt (HMA) and two types of warm mix asphalt (WMA). The results demonstrate a high linear correlation between n and −log A for all the tested field cores. Investigations of the effect of field aging on the fracture properties confirm that n is a good indicator to quantify the cracking resistance of asphalt concrete. It is also indicated that summer climatic condition clearly accelerates the rate of aging. The impact of the WMA technologies on fracture properties of asphalt concrete is visualized by comparing the n-values. It shows that the Evotherm WMA technology slightly improves the cracking resistance, while the foaming WMA technology provides the comparable fracture properties with the HMA. After 15 months aging in the field, the cracking resistance does not exhibit significant difference between HMA and WMAs, which is confirmed by the observations of field distresses.

Investigation on performance characteristics of dense graded hot mix asphalt with RAP and crumb rubber

The objective of this study was to fundamentally characterize the laboratory performance of traditional hot mix asphalt (HMA) mixtures incorporating high RAP content and waste tire crumb rubber through their fundamental engineering properties. The nominal maximum aggregates size was chosen for this research was 12mm (considering the limitation of aggregate size for surface layer) and both coarse and fine aggregates are commonly used in Italy that were examined and analyzed in this study. On the other hand, the RAP plays an important role in reducing production costs and enhancing the environmentally sustainable pavements instead of using virgin materials in HMA. Particularly, this study has aimed to use 30% of RAP content (25% fine aggregate RAP and 5% coarse aggregate RAP) and 1% of CR additives by the total weight of aggregates for mix design. The mixture of aggregates, RAP and CR were blended with different amount of unmodified binder through dry processes. Generally, the main purposes of this study were investigating on capability of using RAP and CR in dense graded HMA and comparing the performance of rejuvenator in RAP with CR. In addition, based on the engineering analyses during the study, we were able compare the fundamental Indirect Tensile Strength (ITS) value of dense graded HMA and also mechanical characteristics in terms of Indirect Tensile Stiffness Modulus (ITSM). In order to get an extended comparable data, four groups of different mixtures such as conventional mixture with only virgin aggregates (DV), mixture with RAP (DR), mixture with RAP and rejuvenator (DRR), and mixture with RAP, rejuvenator, CR (DRRCr) were investigated in this research experimentally. Finally, the results of those tests indicated that the mixtures with RAP and CR had the high stiffness and less thermal sensitivity, while the mixture with virgin aggregates only had very low values in comparison.

Le reologia dei leganti bituminosi stradali: studio delle proprietà meccaniche a seguito di processi di “aging” in laboratorio

Lo studio effettuato pone le sue basi sulla ricerca di materiali stradali che combinino ad elevati standard prestazionali, la riduzione dell’impatto ambientale in fase realizzativa e manutentiva. In particolare il seguente lavoro si occupa dello studio di 7 leganti modificati con polimeri ed additivati con cere. I primi infatti conferiscono alla miscela maggiore elastoplasticità, incrementandone la durabilità e la resistenza a fatica. Nei secondi la presenza del materiale paraffinico contribuisce a ridurre la viscosità del bitume, consentendo un notevole abbassamento della temperatura di produzione e stesa della miscela. Numerosi studi hanno dimostrato che le caratteristiche meccaniche della pavimentazione sono fortemente influenzate dal grado di ossidazione delle componenti organiche del bitume, ovvero dal fenomeno dell’invecchiamento o aging. Pertanto allo studio reologico del bitume, si sono affiancate prove di simulazione dell’ invecchiamento nel breve e lungo termine. In fase di ricerca sperimentale si sono analizzati i leganti modificati ed additivati secondo la teoria della viscoelasticità, simulando le reali condizioni di carico ed invecchiamento alle quali il bitume è sottoposto. Tutte le prove di caratterizzazione reologica avanzata sono state effettuate mediante l’utilizzo del DSR (Dynamic Shear Rheometer - UNI EN 14770 ) in varie configurazioni di prova e l’invecchiamento a breve termine è stato simulato mediante RTFOT (Rolling thin film oven test -UNI EN 12607-1). Si è proposto inoltre una nuova procedura di aging invecchiando il bitume alla temperatura di Twork, ovvero a quel valore della temperatura tale per cui, in fase di messa in opera, si avrà una distribuzione molecolare omogenea del modificante all’interno del bitume.

PERFORMANCE EVALUATION OF LLDPE/CaCO3 MODIFIERS WITH AND WITHOUT TITANATE COUPLING AGENT ON ASPHALT BINDER AND MIXTURE

The complexity and challenge created by asphalt material motivates researchers and engineers to investigate the behavior of this material to develop a better understanding, and improve the performance of asphalt pavement. Over decades, a wide range of modification at macro, meso, micro and nano scales have been conducted to improve the performance of asphalt pavement. This study was initiated to utilize the newly developed asphalt modifier pellets. These pellets consisted of different combinations of calcium carbonate (CaCO3), linear low-density polyethylene (LLDPE) and titanate coupling agent (CA) to improve the asphalt binder as well as pavement performance across a wide range of temperature and loading pace. These materials were used due to their unique characteristics and promising findings from various industries, especially as modifiers in pavement material. The challenge is to make sure the CaCO3 disperses very well in the mixture. The rheological properties of neat asphalt binder PG58-28 and modified asphalt binder (PG58-28/LLDPE, PG58-28/CaCO3, PG58-28/CaCO3/LLDPE, and PG58-28/CaCO3/LLDPE/CA), were determined using rotational viscometer (RV) test, dynamic shear rheometer (DSR) test and bending beam rheometer test. In the DSR test, the specimens were evaluated using frequency sweep and multiple shear creep recovery (MSCR). The asphalt mixtures (aggregate/PG58-28, aggregate/ PG58-28/LLDPE, aggregate/PG58-28/CaCO3, aggregate/PG58-28/LLDPE/CaCO3 and aggregate/PG58-28/LLDPE/CaCO3/CA) were evaluated using the four point beam fatigue test, the dynamic modulus (E*) test, and tensile strength test (to determines tensile strength ratio, TSR). The RV test results show that all modified asphalt binders have a higher viscosity compared to the neat asphalt binder (PG58-28). Based on the Jnr results (using MSCR test), all the modified asphalt binders have a better resistance to rutting compared to the neat asphalt binder. A higher modifier contents have resulted in a better recovery percentage of asphalt binder (higher resistance to rutting), except the specimens prepared using PECC’s modified asphalt binder (PG58-28/CaCO3/LLDPE). The BBR test results show that all the modified asphalt binders have shown comparable performance in term of resistance to low temperature cracking, except the specimen prepared using the LLDPE modifier. Overall, 5 wt% LLDPE modified asphalt binder was found to be the best asphalt binder in terms of resistance to rutting. Meanwhile, 3 wt% PECC-1CA’s modified asphalt binder can be considered as the best (in terms of resistance to thermal cracking) with the lowest mean critical cracking temperature. The appearance of CaCO3 was found useful merely in improving the resistance to fatigue cracking of asphalt mixture. However, application of LLDPE has undermined the fatigue life of asphalt mixtures. Adding LLDPE and coupling agent throughout this study does not sufficiently help in terms of elastic behavior which essential to enhance the resistance to fatigue cracking. In contrast, application of LLDPE has increased the indirect tensile strength values and TSR of asphalt mixtures, indicates a better resistance to moisture damage. The usage of the coupling agent does not change the behavior of the asphalt mixture, which could be due to imbalance effects resulted by combination of LLDPE and CaCO3 in asphalt binder. Further investigations without incorporating CaCO3 should be conducted further. To investigate the feasibility of using LLDPE and coupling agent as modifiers in asphalt pavements, more research should be conducted on different percentages of LLDPE (less than 3 wt%), and at the higher and w wider range of coupling agent content, from 3 wt% to 7 wt% based on the polymer mass.