Hydraulic Conductivity of Model Soil-Bentonite Backfills Subjected to Wet-Dry Cycling

The potential for changes in hydraulic conductivity, k, of two model soil-bentonite (SB) backfills subjected to wet-dry cycling was investigated. The backfills were prepared with the same base soil (clean, fine sand) but different bentonite contents (2.7 and 5.6 dry wt %). Saturation (S), volume change, and k of consolidated backfill specimens (effective stress = 24 kPa) were evaluated over three to seven cycles in which the matric suction, Ym, in the drying stage ranged from 50 to 700 kPa. Both backfills exhibited susceptibility to degradation in k caused by wet-dry cycling. Mean values of k for specimens dried at Ym = 50 kPa (S = 30-60 % after drying) remained low after two cycles, but increased by 5- to 300-fold after three or more cycles. Specimens dried at Ym ≥ 150 kPa (S < 30 % after drying) were less resilient and exhibited 500- to 10 000-fold increases in k after three or more cycles. The greater increases in k for these specimens correlated with greater vertical shrinkage upon drying. The findings suggest that increases in hydraulic conductivity due to wet-dry cycling may be a concern for SB vertical barriers located within the zone of a fluctuating groundwater table.

Multiple-edge noise barriers

A numerical model using boundary element techniques is discussed which enables the insertion loss for various noise barriers of complex profile and surface cover to be calculated. The model is applied to single-foundation noise barriers to which additional side-panels are added to create fork-like profiles. Spectra of insertion loss and mean insertion loss results over a range of receiver positions for a broadband source are presented. It is concluded that ‘multiple-edged’ barriers show a significant increase in acoustic-efficiency over a simple vertical screen. Adding lightweight side-panels would be a relatively inexpensive measure, and one which could be applied to barriers already in existence. This type of barrier would also allow the height of the construction to be kept to a minimum.

Barriers to entry in monopoly markets: automobile distribution in Brazil

O Objetivo deste Trabalho é Analisar os Efeitos da Entrada de uma Segunda Concessionária de Automóveis em Mercados Previamente Monopolizados. para Tanto, Construiu-Se um Banco de Dados com a Localização de Concessionárias de Automóveis em Microrregiões e Características Demográficas e Econômicas Destas Microrregiões. a Partir Desse Banco de Dados e de Modelos de Escolha Binária, Foram Identificadas Variáveis que Condicionam a Existência e o Número de Concessionárias em Microrregiões. Utilizando-Se de um Modelo Adaptado de Bresnahan e Reiss (1990), Foram Estimados os Custos Fixos de Entrada de Concessionárias em Mercados Monopolizados. os Resultados Obtidos Sugerem que as Barreiras À Entrada não são Significativas, o que Aumenta a Probabilidade de que a Cláusula de Exclusividade nos Contratos de Concessão não Cause Danos À Concorrência no Mercado Brasileiro de Distribuição de Automóveis

Vertical Bone Augmentation Using a Polytetrafluoroethylene Nonporous Barrier for Osseointegrated Implants Partially Inserted in Tibiae of Rabbits

Purpose: The aim of this study was to evaluate the possibility of obtaining guided bone regeneration using a poly-tetrafluoroethylene (PTFE) nonporous barrier for 2 endosseous implants, partially inserted in tibiae of rabbits.Materials and Methods: Histologic characteristics of the interface between titanium implants (one group with titanium plasma-coated implants and the other group with acid-treated surfaces) and of the regenerated bone were also studied. Twenty screw-vent implants were placed in tibiae of 5 male New Zealand rabbits, 2 at the right side and 2 at the left side, protruding 3 mm from the bone level, to create a horizontal bone defect. At the experimental group the implants were with a PTFE nonporous barrier, whereas no barriers were used in contralateral implants. Animals were sacrificed 3 months after surgery and biopsy specimens were evaluated histologically and histomorphometrically under light microscopy. Student's t test was used for statistical analysis.Results: The histologic measurements showed a mean gain in bone height of 2.15 and 2.42 mm for the barrier group and 1.95 and 0.43 mm for the control group, for the titanium plasma-spray and acid-treated implant surfaces, respectively.Conclusion: The results of the investigation revealed that the placement of implants protruding 3 nun from crestal bone defects may result in vertical bone augmentation using a nonporous PTFE barrier. (Implant Dent 2009;18:182-191)

Influence of anatomical barriers on maxillary incisor root resorption after orthodontic treatment with premolar extractions

INTRODUCTION: Apical root resorption is a frequent and occasionally critical problem in orthodontic patients undergoing induced tooth movement. One of the factors that might influence prognosis, especially in maxillary incisors, which most frequently present resorptions, are the so-called the anatomical barriers; that is, proximity of the buccal and palatal cortical bones to the maxillary incisor roots. OBJECTIVE: The purpose of this research was to investigate whether patients with excessive vertical growth really present a small distance between the alveolar cortical bones and the maxillary incisor roots, and whether there is a correlation between this distance and the root resorption index in comparison with patients presenting horizontal growth. METHODS: The sample comprised orthodontic records of 18 patients with extraction planning of first maxillary premolars and treatment by the standard and/or preadjusted edgewise brackets. Their initial and final periapical radiographs were evaluated to determine the amount of root resorption that occurred. RESULTS: On the palatal side, patients with excessive vertical growth (Group 2 - SN-GoGn > 43º) showed a narrower alveolar bone than the horizontal growth patients (Group 1 - SN-GoGn < 29º). However, the distance between the buccal cortical bone and the central incisor root apex showed no significant difference between Groups 1 and 2; CONCLUSIONS: It was concluded that there are no correlations between the proximity of buccal cortical bone, maxillary incisor roots and the root resorption index.

Desintegración vertical en la industria del automóvil en España: un caso de estudio = Vertical disintegration in the automotive industry in Spain: a case study

En los años recientes se ha producido un rápido crecimiento del comercio internacional en productos semielaborados que son diseñados, producidos y ensamblados en diferentes localizaciones a lo largo de diferentes países, debido principalmente a los siguientes motivos: el desarrollo de las tecnologías de la información, la reducción de los costes de transporte, la liberalización de los mercados de capitales, la armonización de factores institucionales, la integración económica regional que implica la reducción y la eliminación de las barreras al comercio, el desarrollo económico de los países emergentes, el uso de economías de escala, así como una desregulación del comercio internacional. Todo ello ha incrementado la competencia a nivel mundial en los mercados y ha posibilitado a las compañías tener más facilidad de acceso a potenciales mercados, así como a la adquisición de capacidades y conocimientos en otros países y a la realización de alianzas estratégicas internacionales con terceros, creando un entorno con mayor incertidumbre y más exigente para las compañías que componen una industria, y que tiene consecuencias directas en las operaciones de las compañías y en la organización de su producción. Las compañías, para adaptarse, ser competitivas y beneficiarse de este nuevo escenario globalizado y más competitivo, han externalizado partes del proceso productivo hacia proveedores especializados, creando un nuevo mercado intermedio que divide el proceso productivo, anteriormente integrado en las compañías que conforman una industria, entre dos conjuntos de empresas especializadas en esa industria. Dicho proceso suele ocurrir conservando la industria en que tiene lugar, los mismos servicios y productos, la tecnología empleada y las compañías originales que la conformaban previamente a la desintegración vertical. Todo ello es así debido a que es beneficioso tanto para las compañías originales de la industria como para las nuevas compañías de este mercado intermedio por diversos motivos. La desintegración vertical en una industria tiene unas consecuencias que la transforman completamente, así como la forma de operar de las compañías que la integran, incluso para aquellas que permanecen verticalmente integradas. Una de las características más importantes de esta desintegración vertical en una industria es la posibilidad que tiene una compañía de adquirir a una tercera la primera parte del proceso productivo o un bien semielaborado, que posteriormente será finalizado por la compañía adquiriente con la práctica del outsourcing; así mismo, una compañía puede realizar la primera parte del proceso productivo o un bien semielaborado, que posteriormente será finalizado por una tercera compañía con la práctica de la fragmentación. El principal objetivo de la presente investigación es el estudio de los motivos, los facilitadores, los efectos, las consecuencias y los principales factores significativos, microeconómicos y macroeconómicos, que desencadenan o incrementan la práctica de la desintegración vertical en una industria; para ello, la investigación se divide en dos líneas completamente diferenciadas: el estudio de la práctica del outsourcing y, por otro lado, el estudio de la fragmentación por parte de las compañías que componen la industria del automóvil en España, puesto que se trata de una de las industrias más desintegradas verticalmente y fragmentadas, y este sector posee una gran importancia en la economía del país. En primer lugar, se hace una revisión de la literatura existente relativa a los siguientes aspectos: desintegración vertical, outsourcing, fragmentación, teoría del comercio internacional, historia de la industria del automóvil en España y el uso de las aglomeraciones geográficas y las tecnologías de la información en el sector del automóvil. La metodología empleada en cada uno de ellos ha sido diferente en función de la disponibilidad de los datos y del enfoque de investigación: los factores microeconómicos, utilizando el outsourcing, y los factores macroeconómicos, empleando la fragmentación. En el estudio del outsourcing, se usa un índice basado en las compras externas sobre el valor total de la producción. Así mismo, se estudia su correlación y significación con las variables económicas más importantes que definen a una compañía del sector del automóvil, utilizando la técnica estadística de regresión lineal. Aquellas variables relacionadas con la competencia en el mercado, la externalización de las actividades de menor valor añadido y el incremento de la modularización de las actividades de la cadena de valor, han resultado significativas con la práctica del outsourcing. En el estudio de la fragmentación se seleccionan un conjunto de factores macroeconómicos, comúnmente usados en este tipo de investigaciones, relacionados con las principales magnitudes económicas de un país, y un conjunto de factores macroeconómicos, no comúnmente usados en este tipo de investigaciones, relacionados con la libertad económica y el comercio internacional de un país. Se emplea un modelo de regresión logística para identificar qué factores son significativos en la práctica de la fragmentación. De entre todos los factores usados en el modelo, los relacionados con las economías de escala y los costes de servicio han resultado significativos. Los resultados obtenidos de los test estadísticos realizados en el modelo de regresión logística han resultado satisfactorios; por ello, el modelo propuesto de regresión logística puede ser considerado sólido, fiable y versátil; además, acorde con la realidad. De los resultados obtenidos en el estudio del outsourcing y de la fragmentación, combinados conjuntamente con el estado del arte, se concluye que el principal factor que desencadena la desintegración vertical en la industria del automóvil es la competencia en el mercado de vehículos. Cuanto mayor es la demanda de vehículos, más se reducen los beneficios y la rentabilidad para sus fabricantes. Estos, para ser competitivos, diferencian sus productos de la competencia centrándose en las actividades que mayor valor añadido aportan al producto final, externalizando las actividades de menor valor añadido a proveedores especializados, e incrementando la modularidad de las actividades de la cadena de valor. Las compañías de la industria del automóvil se especializan en alguna o varias de estas actividades modularizadas que, combinadas con el uso de factores facilitadores como las economías de escala, las tecnologías de la información, las ventajas de la globalización económica y la aglomeración geográfica de una industria, incrementan y motivan la desintegración vertical en la industria del automóvil, desencadenando la coespecialización en dos sectores claramente diferenciados: el sector de fabricantes de vehículos y el sector de proveedores especializados. Cada uno de ellos se especializa en unas actividades y en unos productos o servicios específicos de la cadena de valor, lo cual genera las siguientes consecuencias en la industria del automóvil: se reducen los costes de transacción en los productos o servicios intercambiados; se incrementan la relación de dependencia entre fabricantes de vehículos y proveedores especializados, provocando un aumento en la cooperación y la coordinación, acelerando el proceso de aprendizaje, posibilitando a ambos adquirir nuevas capacidades, conocimientos y recursos, y creando nuevas ventajas competitivas para ambos; por último, las barreras de entrada a la industria del automóvil y el número de compañías se ven alteradas cambiando su estructura. Como futura línea de investigación, los fabricantes de vehículos tenderán a centrarse en investigar, diseñar y comercializar el producto o servicio, delegando el ensamblaje en manos de nuevos especialistas en la materia, el contract manufacturer; por ello, sería conveniente investigar qué factores motivantes o facilitadores existen y qué consecuencias tendría la implantación de los contract manufacturer en la industria del automóvil. 1.1. ABSTRACT In recent years there has been a rapid growth of international trade in semi-finished products designed, produced and assembled in different locations across different countries, mainly due to the following reasons: development of information technologies, reduction of transportation costs, liberalisation of capital markets, harmonisation of institutional factors, regional economic integration, which involves the reduction and elimination of trade barriers, economic development of emerging countries, use of economies of scale and deregulation of international trade. All these factors have increased competition in markets at a global level and have allowed companies to gain easier access to potential markets and to the acquisition of skills and knowledge in other countries, as well as to the completion of international strategic alliances with third parties, thus creating a more demanding and uncertain environment for these companies constituting an industry, which has a direct impact on the companies' operations and the organization of their production. In order to adapt, be competitive and benefit from this new and more competitive global scenario, companies have outsourced some parts of their production process to specialist suppliers, generating a new intermediate market which divides the production process, previously integrated in the companies that made up the industry, into two sets of companies specialized in that industry. This process often occurs while preserving the industry where it takes place, its same services and products, the technology used and the original companies that formed it prior to vertical disintegration. This is because it is beneficial for both the industry's original companies and the companies belonging to this new intermediate market, for various reasons. Vertical disintegration has consequences which completely transform the industry where it takes place as well as the modus operandi of the companies that are part of it, even of those who remain vertically integrated. One of the most important features of vertical disintegration of an industry is the possibility for a company to acquire from a third one the first part of the production process or a semi-finished product, which will then be finished by the acquiring company through the practice of outsourcing; also, a company can perform the first part of the production process or a semi-finish product, which will then be completed by a third company through the practice of fragmentation. The main objective of this research is to study the motives, facilitators, effects, consequences and major significant microeconomic and macroeconomic factors that trigger or increase the practice of vertical disintegration in a certain industry; in order to do so, research is divided into two completely differentiated lines: on the one hand, the study of the practise of outsourcing and, on the other, the study of fragmentation by companies constituting the automotive industry in Spain, since this is one of the most vertically disintegrated and fragmented industries and this particular sector is of major significance in this country's economy. First, a review is made of the existing literature, on the following aspects: vertical disintegration, outsourcing, fragmentation, international trade theory, history of the automobile industry in Spain and the use of geographical agglomeration and information technologies in the automotive sector. The methodology used for each of these aspects has been different depending on the availability of data and the research approach: the microeconomic factors, using outsourcing, and the macroeconomic factors, using fragmentation. In the study on outsourcing, an index is used based on external purchases in relation to the total value of production. Likewise, their significance and correlation with the major economic variables that define an automotive company are studied, using the statistical technique of linear regression. Variables related to market competition, outsourcing of lowest value-added activities and increased modularisation of the activities of the value chain have turned out to be significant with the practice of outsourcing. In the study of fragmentation, a set of macroeconomic factors commonly used for this type of research, is selected, related to the main economic indicators of a country, as well as a set of macroeconomic factors, not commonly used for this type of research, which are related to economic freedom and the international trade of a certain country. A logistic regression model is used to identify which factors are significant in the practice of fragmentation. Amongst all factors used in the model, those related to economies of scale and service costs have turned out to be significant. The results obtained from the statistical tests performed on the logistic regression model have been successful; hence, the suggested logistic regression model can be considered to be solid, reliable and versatile; likewise, it is in line with reality. From the results obtained in the study of outsourcing and fragmentation, combined with the state of the art, it is concluded that the main factor that triggers vertical disintegration in the automotive industry is competition within the vehicle market. The greater the vehicle demand, the lower the earnings and profitability for manufacturers. These, in order to be competitive, differentiate their products from the competition by focusing on those activities that contribute with the highest added value to the final product, outsourcing the lower valueadded activities to specialist suppliers, and increasing the modularity of the activities of the value chain. Companies in the automotive industry specialize in one or more of these modularised activities which, combined with the use of enabling factors such as economies of scale, information technologies, the advantages of economic globalisation and the geographical agglomeration of an industry, increase and encourage vertical disintegration in the automotive industry, triggering co-specialization in two clearly distinct sectors: the sector of vehicle manufacturers and the specialist suppliers sector. Each of them specializes in certain activities and specific products or services of the value chain, generating the following consequences in the automotive industry: reduction of transaction costs of the goods or services exchanged; growth of the relationship of dependency between vehicle manufacturers and specialist suppliers, which causes an increase in cooperation and coordination, accelerates the learning process, enables both to acquire new skills, knowledge and resources, and creates new competitive advantages for both; finally, barriers to entry the automotive industry and the number of companies are altered, changing their structure. As a future line of research, vehicle manufacturers will tend to focus on researching, designing and marketing the product or service, delegating the assembly in the hands of new specialists in the field, the contract manufacturer; for this reason, it would be useful to investigate what motivating or facilitating factors exist in this respect and what consequences would the implementation of contract manufacturers have in the automotive industry.

The Inadequacy Of The Y-axis Of Growth (sngn) For The Vertical Pattern Assessment In Patients With Sagittal Discrepancies.

The aim of this cephalometric study was to evaluate the influence of the sagittal skeletal pattern on the 'Y-axis of growth' measurement in patients with different malocclusions. Lateral head films from 59 patients (mean age 16y 7m, ranging from 11 to 25 years) were selected after a subjective analysis of 1630 cases. Sample was grouped as follows: Group 1 - class I facial pattern; group 2 - class II facial pattern; and Group 3 - class III facial pattern. Two angular measurements, SNGoGn and SNGn, were taken in order to determine skeletal vertical facial pattern. A logistic regression with errors distributed according to a binomial distribution was used to test the influence of the sagittal relationship (Class I, II, III facial patterns) on vertical diagnostic measurement congruence (SNGoGn and SNGn). RESULTS show that the probability of congruence between the patterns SNGn and SNGoGn was relatively high (70%) for group 1, but for groups II (46%) and III (37%) this congruence was relatively low. The use of SNGn appears to be inappropriate to determine the vertical facial skeletal pattern of patients, due to Gn point shifting throughout sagittal discrepancies. Clinical Significance: Facial pattern determined by SNGn must be considered carefully, especially when severe sagittal discrepancies are present.

Vertical Bone Measurements From Cone Beam Computed Tomography Images Using Different Software Packages.

This article aimed at comparing the accuracy of linear measurement tools of different commercial software packages. Eight fully edentulous dry mandibles were selected for this study. Incisor, canine, premolar, first molar and second molar regions were selected. Cone beam computed tomography (CBCT) images were obtained with i-CAT Next Generation. Linear bone measurements were performed by one observer on the cross-sectional images using three different software packages: XoranCat®, OnDemand3D® and KDIS3D®, all able to assess DICOM images. In addition, 25% of the sample was reevaluated for the purpose of reproducibility. The mandibles were sectioned to obtain the gold standard for each region. Intraclass coefficients (ICC) were calculated to examine the agreement between the two periods of evaluation; the one-way analysis of variance performed with the post-hoc Dunnett test was used to compare each of the software-derived measurements with the gold standard. The ICC values were excellent for all software packages. The least difference between the software-derived measurements and the gold standard was obtained with the OnDemand3D and KDIS3D (-0.11 and -0.14 mm, respectively), and the greatest, with the XoranCAT (+0.25 mm). However, there was no statistical significant difference between the measurements obtained with the different software packages and the gold standard (p> 0.05). In conclusion, linear bone measurements were not influenced by the software package used to reconstruct the image from CBCT DICOM data.

Sistema de análise de movimento para avaliação da postura vertical durante a corrida no teste de esforço máximo incremental

Universidade Estadual de Campinas . Faculdade de Educação Física

Atividade fisica e aptidão fisica de adolescentes : similaridades e contrastes em uma decada

Universidade Estadual de Campinas . Faculdade de Educação Física

Performance da resistencia muscular de membros inferiores em praticantes da modalidade esportiva voleibol, atraves do salto vertical

Universidade Estadual de Campinas. Faculdade de Educação Física

Estudo do salto vertical : uma analise da relação de forças aplicadas

Universidade Estadual de Campinas. Faculdade de Educação Física

Effect of cyclic load on vertical misfit of prefabricated and cast implant single abutment

OBJECTIVES: The purpose of this in vitro study was to evaluate misfit alterations at the implant/abutment interface of external and internal connection implant systems when subjected to cyclic loading. MATERIAL AND METHODS: Standard metal crowns were fabricated for 5 groups (n=10) of implant/abutment assemblies: Group 1, external hexagon implant and UCLA cast-on premachined abutment; Group 2, internal hexagon implant and premachined abutment; Group 3, internal octagon implant and prefabricated abutment; Group 4, external hexagon implant and UCLA cast-on premachined abutment; and Group 5, external hexagon implant and Ceraone abutment. For groups 1, 2, 3 and 5, the crowns were cemented on the abutments and in group 4 crowns were screwed directly on the implant. The specimens were subjected to 500,000 cycles at 19.1 Hz of frequency and non-axial load of 133 N in a MTS 810 machine. The vertical misfit (μm) at the implant/abutment interface was evaluated before (B) and after (A) application of the cyclic loading. Data were analyzed statistically by using two-away ANOVA and Tukey's post-hoc test (p<0.05). RESULTS: Before loading values showed no difference among groups 2 (4.33±3.13), 3 (4.79±3.43) and 5 (3.86±4.60); between groups 1 (12.88±6.43) and 4 (9.67±3.08), and among groups 2, 3 and 4. However, groups 1 and 4 were significantly different from groups 2, 3 and 5. After loading values of groups 1 (17.28±8.77) and 4 (17.78±10.99) were significantly different from those of groups 2 (4.83±4.50), 3 (8.07±4.31) and 5 (3.81±4.84). There was a significant increase in misfit values of groups 1, 3 and 4 after cyclic loading, but not for groups 2 and 5. CONCLUSIONS: The cyclic loading and type of implant/abutment connection may develop a role on the vertical misfit at the implant/abutment interface.

Vertical alveolar crest bone maintenance around implants in two-stage surgery: an in situ study in dogs

The aim of this study was to evaluate in situ changes in the alveolar crest bone height around immediate implant-supported crowns in comparison to tooth-supported crowns (control) with the cervical margins located at the bone crest level, without occlusal load. In Group I, after extraction of 12 mandibular premolars from 4 adult dogs, implants from Branemark System (MK III TiU RP 4.0 x 11.5 mm) were placed to retain complete acrylic crowns. In Group II, premolars were prepared to receive complete metal crowns. Sixteen weeks after placement of the crowns (38 weeks after tooth extraction), the height of the alveolar bone crest was measured with a digital caliper. Data were analyzed statistically by the Mann-Whitney test at 5% significance level. The in situ analysis showed no statistically significant difference (p=0.880) between the implant-supported and the tooth-supported groups (1.528 + 0.459 mm and 1.570 + 0.263 mm, respectively). Based on the findings of the present study, it may be concluded that initial peri-implant bone loss may result from the remodeling process necessary to establish the biological space, similar to which occurs with tooth-supported crowns.

Relation between implant/abutment vertical misfit and torque loss of abutment screws

This study investigated whether there is a direct correlation between the level of vertical misfit at the abutment/implant interface and torque losses (detorque) in abutment screws. A work model was obtained from a metal matrix with five 3.75 x 9 mm external hex implants with standard platform (4.1 mm). Four frameworks were waxed using UCLA type abutments and one-piece cast in commercially pure titanium. The misfit was analyzed with a comparator microscope after 20 Ncm torque. The highest value of misfit observed per abutment was used. The torque required to loose the screw was evaluated using a digital torque meter. The torque loss values, measured by the torque meter, were assumed as percentage of initial torque (100%) given to abutment screws. Pearson's correlation (α=0.05) between the misfit values (29.08 ± 8.78 µm) and the percentage of detorque (50.71 ± 11.37%) showed no statistically significant correlation (p=0.295). Within the limitations of this study, it may be concluded that great vertical misfits dot not necessarily implies in higher detorque values.