An ultrafiltration membrane, prepared with MSU-type mesoporous silica: Preparation and specific filtration behavior

We report preparation and the singular filtration properties of an ultrafiltration membrane made with MSU-type mesoporous silica that exhibits cylindrical pores aligned mostly normal to the support. This membrane supported on tubular commercial macroporous alumina supports was prepared by the interfacial growth mechanism between stable silica-surfactant hybrid micelles made of the association of silica oligomers with polyethyleneoxide-based (PEO) surfactants and sodium fluoride, a well-known silica condensation catalyst. It appears that the combined effect of the silica nature of the membrane, whose surface charge can be easily adjusted by changing the pH and the non-connected cylindrical shape of the pores provides a new behavior in the retention properties, as proved by the filtration of polyoxyethylene polymers (PEO) with different molecular weights. Depending on the filtration conditions, a rejection rate of 80 % and a steep cut-off at 2,000 Da can be obtained or, on the reverse, polymers three times bigger than the pore diameter can diffuse through the membrane. This new filtration mechanism, which opens up new modes of separation modes, is explained in the light of both topology of the porous network and pH-dependent interactions between PEO polymers and silica porous media. © 2005 Elsevier B.V. All rights reserved.

Development of a LCST membrane forming system for cellulose acetate ultrafiltration hollow fiber

A novel lower critical solution temperature (LCST) membrane forming system containing cellulose acetate (CA)/poly (vinyl pyrrolidone) (PVP 3 60K)/N-methyl-2-pyrrolidone (NMP)/1,2-propanediol with a weight ratio of 24.0:5.0:62.6:8.4 had been developed. CA hollow fiber ultrafiltration (UF) membranes were fabricated using the dry-wet spinning technique. The fibers were post-treated with a 200 mg/L hypochlorite solution over a period of 6 It at pH 7. The experimental results showed that water flux of a membrane decreased while retention increased with increasing CA concentration in a dope. It was concluded that the membrane pore size decreased with increasing CA concentration. The membrane fouling tendency for BSA was 3 times higher than that for PVP 24K. (C) 2004 Elsevier B.V. All rights reserved.

Synthesis of isomaltooligosaccharides and oligodextrans in a recycle membrane bioreactor by the combined use of dextransucrase and dextranase

A recycle ultrafiltration membrane reactor was used to develop a continuous synthesis process for the production of isomaltooligosaccharides (IMO) from sucrose, using the enzymes dextransucrase and dextranase. A variety of membranes were tested and the parameters affecting reactor stability, productivity, and product molecular weight distribution were investigated. Enzyme inactivation in the reactor was reduced with the use of a non-ionic surfactant but its use had severe adverse effects on the membrane pore size and porosity. During continuous isomaltooligosaccharide synthesis, dextransucrase inactivation was shown to occur as a result of the dextranase activity and it was dependent mainly on the substrate availability in the reactor and the hydrolytic activity of dextranase. Substrate and dextranase concentrations (50-200 mg/mL(-1) and 10-30 U/mL(-1), respectively) affected permeate fluxes, reactor productivity, and product average molecular weight. The oligodextrans and isomaltooligosaccharides formed had molecular weights lower than in batch synthesis reactions but they largely consisted of oligosaccharides with a degree of polymerization (DP) greater than 5, depending on the synthesis conditions. No significant rejection of the sugars formed was shown by the membranes and permeate flux was dependent on tangential flow velocity. (C) 2004 Wiley Periodicals, Inc.

On the specific filtration mechanism of a mesoporous silica membrane, prepared with non-connecting parallel pores

We report the singular filtration properties of an ultrafiltration membrane made with mesoporous silica that exhibits cylindrical pores aligned mostly normal to the support. This membrane supported on tubular commercial macroporous alumina supports was prepared by the interfacial growth mechanism between stable silica-surfactant hybrid micelles made of the association of silica oligomers with polyethyleneoxide-based (PEO) surfactants and sodium fluoride, a well-known silica condensation catalyst [Boissière et al., An ultrafiltration membrane made with mesoporous MSU-X silica, Chem. Mater. 15 (2003) 460-463]. It appears that the combined effect of the silica nature of the membrane, whose surface charge can be easily adjusted by changing the pH and the non-connected cylindrical shape of the pores provides a new behavior in the retention properties, as proved by the filtration of polyoxyethylene polymers (PEO) with different molecular weights. Depending on the filtration conditions, a rejection rate of 80% and a steep cut-off at 2000 Da can be obtained or, on the reverse, polymers three times bigger than the pore diameter can diffuse through the membrane. This new filtration mechanism, which opens up new modes of separation modes, is explained in the light of both topology of the porous network and pH-dependent interactions between PEO polymers and silica porous media. © 2004 Elsevier B.V. All rights reserved.

Binary metal oxides for composite ultrafiltration membranes

A new ultrafiltration membrane was developed by the incorporation of binary metal oxides inside polyethersulfone. Physico-chemical characterization of the binary metal oxides demonstrated that the presence of Ti in the TiO2?ZrO2 system results in an increase of the size of the oxides, and also their dispersity. The crystalline phases of the synthesized binary metal oxides were identified as srilankite and zirconium titanium oxide. The effect of the addition of ZrO2 can be expressed in terms of the inhibition of crystal growth of anocrystalline TiO2 during the synthesis process. For photocatalytic applications the band gap of the synthesized semiconductors was determined, confirming a gradual increase (blue shift) in the band gap as the amount of Zr loading increases. Distinct distributions of binary metal oxides were found along the permeation axis for the synthesized membranes. Particles with Ti are more uniformly dispersed throughout the membrane cross-section. The physico-chemical characterization of membranes showed a strong correlation between some key membrane properties and the spatial particle distribution in the membrane structure. The proximity of metal oxide fillers to the membrane surface determines the hydrophilicity and porosity of modified membranes. Membranes incorporating binary metal oxides were found to be promising candidates for wastewater treatment by ultrafiltration, considering the observed improvement influx and anti-fouling properties of doped membranes. Multi-run fouling tests of doped membranes confirmed the stability of permeation through membranes embedded with binary TiO2?ZrO2 particles.

Downstream processing of reverse osmosis brine: Characterisation of potential scaling compounds

Reverse osmosis (RO) brine produced at a full-scale coal seam gas (CSG) water treatment facility was characterized with spectroscopic and other analytical techniques. A number of potential scalants including silica, calcium, magnesium, sulphates and carbonates, all of which were present in dissolved and non-dissolved forms, were characterized. The presence of spherical particles with a size range of 10–1000 nm and aggregates of 1–10 microns was confirmed by transmission electron microscopy (TEM). Those particulates contained the following metals in decreasing order: K, Si, Sr, Ca, B, Ba, Mg, P, and S. Characterization showed that nearly one-third of the total silicon in the brine was present in the particulates. Further, analysis of the RO brine suggested supersaturation and precipitation of metal carbonates and sulphates during the RO process should take place and could be responsible for subsequently capturing silica in the solid phase. However, the precipitation of crystalline carbonates and sulphates are complex. X-ray diffraction analysis did not confirm the presence of common calcium carbonates or sulphates but instead showed the presence of a suite of complex minerals, to which amorphous silica and/or silica rich compounds could have adhered. A filtration study showed that majority of the siliceous particles were less than 220 nm in size, but could still be potentially captured using a low molecular weight ultrafiltration membrane.

Investigation of Extration Method for Paralytic Shellfish Poisoning Toxins in Shellfish

Me optimal conditions were established for the extraction of paralytic shellfish poisoning toxins from gonad of Chlamys nobills using acetic acid and hydrochloric acid in the concentration range of 0.04-1.0 mol/L. A 10-g portion of gonad of Chlamys nobilis was extracted by boiling for 5 min with 1.0 mL acetic acid and hydrochloric acid in a 50-mL beaker. Meanwhile, a portion of gonad of Chlamys nobilis was extracted by sonication in the solution of 0.3 mol/L HAc + 0.2 mol/L HCl for a total period of 5-30 min. The raw extract was centrifuged at 3500 r/min for 5 min and the pH of supernatant was adjusted from 2.0 to 4.0 by 0.1 mol/L NaOH or 5 mol/L HCL After passing through a Millipore ultrafiltration membrane (10000 MW cut-off), ultrafiltrate was then analyzed by HPLC. The results showed that hydrochloric acid in the concentration range of 0.25-1.0 mol/L caused a significant decrease of N-sulfocarbarnoyl-11-hydroxysulfate toxin C1 (C1), C2 and gonyautoxin 5 (GTX5) and the concomitant increase of GTX2,3. However, the amount of the three unstable toxins did not show any change using the extraction with acetic acid. Under the same concentration of acetic acid (0.3 mol/L) and hydrochloric acid (0.2 mol/L), the amount of C1 in the ultrasonic extraction was obviously lower than the boiling one, while C2 showed slightly higher than the latter.

Mesoporous spinel MgAl2O4 prepared by in situ modification of boehmite sol particle surface: I Synthesis and characterization of the unsupported membranes

Mesoporous spinel membranes as ultrafiltration membranes were prepared through a novel sol-gel technique. By in situ modification of the sol particle surface during the sol-gel process, control of the material structure on a nanometer scale from the earliest stages of processing was realized. Nano-particles with a chocolate-nut-like morphology, i.e. spinel MgAl2O4 as a shell and gamma -Al2O3 as a core, were first revealed by HRTEM results. The formation of the spinel phase was confirmed by X-ray diffraction (XRD). N-2 adsorption-desorption results showed that the mesoporous membranes had a narrow pore size distribution. (C) 2001 Elsevier Science B.V. All rights reserved.

Effets des nanoparticules d'argent sur les processus enzymatiques des sols

Les nanomatériaux sont de plus en plus présents dans les produits consommables du quotidien. L’argent est le métal le plus utilisé en nanotechnologie pour ses propriétés antimicrobiennes. Par différentes voies d’entrée, les nanoparticules d’argent (nAg) se retrouvent dans l’environnement en quantité significative, notamment dans les sols suite à la valorisation agricole des biosolides municipaux. Il est prévu qu’une interaction négative sur la communauté microbienne terrestre ait des répercussions sur la fertilité du sol et les processus biogéochimiques. Les mesures de l’activité enzymatique ont déjà montré leur efficacité et leur sensibilité dans la détection d’une perturbation physique et chimique du sol. Les effets potentiels des nAg sur l’écosystème terrestre ont été évalués en mesurant l’activité des enzymes β-D-glucosidase (EC 3.2.1.21), leucine-aminopeptidase (EC 3.4.11.1), phosphomonoesterase (EC 3.1.3) et arylsulfatase (EC 3.1.6.1) intervenant dans les cycles des éléments essentiels C, N, P et S, respectivement. L’activité enzymatique est mesurée à l’aide d’une technique basée sur la fluorescence qui requière des substrats synthétiques liés à un fluorophore. Un sol de type sableux a été échantillonné au Campus Macdonald de l’Université McGill (Sainte-Anne-de-Bellevue, Qc) puis exposé aux nAg (taille ~20 nm) ou à la forme ionique Ag+ (Ag-acetate) à des concentrations nominales de 1,25 × 10-3, 1,25 × 10-2, 0,125, 1,25, 6,25 et 31,25 mg Ag kg-1 sol. De plus, le rôle de la matière organique (MO) a été évalué en effectuant un amendement du sol avec un compost de feuilles. Pour mieux comprendre les effets observés, des analyses de spéciation de l’Ag ont été réalisées. Les concentrations en Ag dissous ont été déterminées après filtration à travers des membranes de 0,45 µm ou de 3 kDa (~1 nm, ultrafiltration) pour séparer la phase particulaire des ions dissous. De façon générale, une inhibition de l’activité enzymatique a été observée pour les 4 enzymes en fonction de l’augmentation de la concentration en Ag (totale et dissoute) mais elle est significativement moins importante avec l’ajout de la MO. Les résultats suggèrent que l’inhibition de l’activité des enzymes aux faibles expositions aux nAg est due aux nanoparticules puisqu’une très faible fraction des nAg est réellement dissoute et aucun effet significatif n’a été observé pour les sols traités à des concentrations similaires en Ag+. Par contre, les effets mesurés aux concentrations plus élevées en nAg sont semblables aux expositions à l’Ag+ et suggèrent un rôle de l’Ag colloïdale dans l’inhibition du processus enzymatique des sols.

Fractionation of oligosaccharides by nanofiltration

Two loose nanofiltration membranes (NF-CA-50 and NF-TFC-50) and one dense ultrafiltration membrane (UF-CA-1) were used to fractionate commercial oligosaccharide mixtures by applying diafiltration in a 'dead-end' filtration cell at 40bar constant pressure with a maximum volume concentration ratio (VCR) of 6 at each fractionation. The rejections of a monosaccharide (glucose) and a disaccharide (lactose) were determined for each membrane; the results indicated that fractionation between these two sugars was possible using the two nanofiltration membranes. During the nanofiltration purification of a commercial oligosaccharide mixture, yields of 19% (w/w) for monosaccharides and 88% (w/w) for di- and oligosaccharides were obtained with the NF-TFC-50 membrane after four filtration steps, indicating that removal of the monosaccharides is possible with only minor losses of the oligosaccharide content of the mixture. The ultrafiltration membrane, at the same time, gave purification levels similar to the NF-TFC-50 membrane with fewer diafiltration steps but with higher losses of di- and oligosaccharides (12% (w/w) for monosaccharides and 53% (w/w) for di- and oligosaccharides on the third run). (C) 2003 Society of Chemical Industry.

Separation of oligosaccharides from caprine milk whey, prior to prebiotic evaluation

Milk oligosaccharides are believed to have beneficial biological properties. Caprine milk has a relatively high concentration of oligosaccharides in comparison to other ruminant milks and has the closest oligosaccharide profile to human milk. The first stage in recovering oligosaccharides from caprine milk whey, a by-product of cheese making, was accomplished by ultrafiltration to remove proteins and fat globules, leaving more than 97% of the initial carbohydrates, mainly lactose, in the permeate. The ultrafiltered permeate was further processed using a 1 kDa ‘tight’ ultrafiltration membrane, which retained less than 7% of the remaining lactose. The final retentate was fractionated by preparative scale molecular size exclusion chromatography, to yield 28 fractions, of which oligosaccharide-rich fractions were detected somewhere between fractions 9/10 to 16/17, suitable for functionality and gut health promotion testing. All fractions were evaluated for their oligosaccharide and carbohydrate profiles using three complementary analytical methods.

Tratamento físico-químico de efluentes de curtume por meio de filtros de membrana seletiva

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Eficiência do processo de ultrafiltração seguido de biodigestão anaeróbia no tratamento de efluente de frigorífico de tilápia

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Substâncias húmicas: interações com nutrientes e contaminantes

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência da pressão e da vazão de concentrado sobre o desempenho de ultrafiltração no pós-tratamento de esgotos

Despite the numerous advantages resulting from the use of membrane filters technology, intrinsic limitations fouling process become relevant to its applicability. The control of operating conditions is an important tool to mitigate fouling and achieve good levels of efficiency. In this sense, the objective of this study was to investigate the effect of transmembrane pressure and concentrate flow in the performance of ultrafiltration, applied to the post-treatment of domestic sewage. The process was evaluated and optimized by varying the pressure (0.5 and 1.5 bar) and the concentrate flow (300 and 600 L/h), using a 22 factorial design, in order to investigate the effects on the permeate flow and quality of effluents generated at each operating condition. We evaluated the following quality indicators for permeate: pH, electrical conductivity, total suspended solids, turbidity, calcium and Chemical Oxygen Demand (COD). In all tests, we observed marked reduction in the permeate flux at the early stages, followed by a slow decline that lasted until it reaches a relatively constant level, around 120 minutes of filtration. The increased pressure resulted in a higher initial permeate flux, but the decrease of the flow with time is greater for tests at higher pressure, indicating a more pronounced fouling process. On the other hand, increasing the concentrate flow resulted in a slower decline in permeate flux with the filtration time. Regarding the quality of permeate, the transmembrane pressure of 0,5 bar was the one that allowed better results, and was statistically confirmed through the two-way ANOVA test with repeated measures, significant effect of pressure on the turbidity of the permeate. The concentrate flow, in turn, showed no significant influence on any of the quality parameters. Thus, we conclude that, from an economic and environmental point of view, it is more interesting to operate ultrafiltration membrane system with a lower concentrate flow associated with a low transmembrane pressure, since under these conditions will produce less waste, and the permeate will present lower concentrations of the analyzed constituent, especially lower turbidity.