Twist distribution in staple fibre yarns

Staple fibre yarns vary quite markedly in linear density (tex) along their length and the degree to which twist redistributes from thick to thin places will affect the strength, torque and extension behaviour of the yarn. Theory suggests that twist along worsted yarns should vary as 1/(tex)2 if fibres were locked in the structure, whereas themean torque of worsted yarns reported in the literature implies that twist should be proportional to 1/tex. This article examines twist distribution in ring-spun marl yarns, down to 5 mm resolution, as a function of linear density measured using a high-resolution capacitive sensor. It is found for moderate twist-level worsted yarns that twist is approximately proportional to 1/(tex)1.6. The results and theory provide a guide as to the effect the observed large variations in linear density will have on yarn properties such as tenacity and torque.

The combined tensile and torsional behavior of irregular fibers

Most fibers are irregular, and they are often subjected to combined loading conditions during processing and end-use. In this paper, polyester and wool fibers under the combined tensile and torsional loads have been studied for the first time, using the finite element method (FEM). The dimensional irregularities of these fibers are simulated with sine waves of different magnitude and frequency. The breaking load and breaking extension of the fibers at different twist or torsion levels are then calculated from the finite element model. The results indicate that twist and level of fiber irregularity have a major impact on the mechanical properties of the fiber and the effect of the frequency of irregularity is relatively small.

Comparing the hairiness of solospun and ring spun worsted yarns

This paper compares the hairiness of Solospun yarns with conventional ring spun worsted yams of the same specifications. A 24-spindles worsted ring spinning frame is used to spin the Solospun and conventional ring spun yarns at the same time, and yarn hairiness is measured. The total hairiness number (Tp), the number of hairs longer than or equal to 3mm (S3), the percentage of longer hairs in total hairs (100S3/Tp), and the total hair length per unit yarn length (K' ) are used to compare the hairiness of these yams. The results indicate that the Solospun yarn exhibits less hairiness in each of the hair length groups and has lower variations in yarn hairiness. The hair-length distribution of the Solospun yarn follows an exponential law just like conventional ring spun yams. There is a statistically significant difference between the Solospun and conventional ring spun yams for T p, S3, and K', but the difference in 1 00S 3/Tp is not statistically significant for these yams. In addition, the Tp, S3, and K' values of the Solospun yarn decrease with twist increase and increase with spindle speed increase, but the 100S3/Tp values of the Solospun and conventional ring spun yarns in this study behave differently in that they are affected by twist level and spindle speed.

Investigation of yarn hairiness

Yarn hairiness affects not only the quality of products, but also the productivity in spinning and weaving. Too much yarn hairiness is undesirable for many end uses as well as the spinning and post spinning processes. The main aims of this project are to examine the hairiness features of various yarns and to reduce yarn hairiness. The thesis covers five related areas – hairiness assessment, factors affecting yarn hairiness, the hairiness of newly developed yarns, yarn hairiness reduction, and effect of yarn hairiness on the energy consumption in ring spinning. The worsted cashmere, pure wool and wool/cashmere blend yarns were employed to investigate the effect of some fibre parameters on the yarn hairiness. A single exponential distribution of the hair-length was confirmed first, using the data from the Zweigle G565 Hairiness Meter. A linear relationship was observed between the blend ratio and the hairiness indexes. In particular, the effect of fibre crimp or curvature on yarn hairiness is examined. The theory of yarn hairiness composition was also developed further. The effect of draft ratio and spindle speed on the hairiness of worsted wool yarn was examined next with a factorial experiment design. Several new hairiness indexes, namely the relative hairiness indexes, have been used to explain the results obtained. In the investigation of the hairiness of newly developed yarns, the hairiness of the Compact Spun and Roller-Jet-Spun yarns was examined first. The composition of the yarn hairiness, the hair-length distribution, and the effect of test speed on yarn hairiness were then studied. An important finding is that for both yarns, the predominant hairiness feature is the looped hairs. A comparison of the hairiness of Solospun yarns and the equivalent ring spun wool yarns was undertaken. The hair-length distribution of the Solospun yarn was examined first. The Solospun yarns used had fewer hairs in most hair-length groups and lower variations in hairiness. In addition, the effect of twist level and spindle speed on the hairiness of Solospun and conventional ring spun yarns has also been discussed. A novel approach of reducing yarn hairiness – spinning with a ‘Diagonal’ yarn path was examined next. Both ‘Left Diagonal’ and ‘Right Diagonal’ yarn arrangements were studied. A new finding is that the ‘Right Diagonal’ yarn path leads to reduced hairiness for the Z-twist yarn, while yarn evenness and tenacity are not as sensitive to the modified yarn path. The mechanism of hairiness reduction with the ‘Diagonal’ yarn path has been discussed. The spinning performance of “Right Diagonal” yarn arrangement has also been evaluated. Finally, the effect of yarn hairiness on the energy consumption in ring spinning has been investigated theoretically and experimentally. A theoretical model has been developed, which represents the first attempt at theoretically investigating the influence of yarn hairiness on energy consumption during the winding stage of ring spinning. The experimental results have generally confirmed predictions of this model. Recommendations for further research in this area have also been made in the concluding chapter of this thesis.

Strip twisted electrospun nanofiber yarns: Structural effects on tensile properties

Nanofiber yarns with controlled twist levels were prepared by twisting a narrow fibrous strip cut directly from electrospun nanofiber mats. The effects of fiber morphology, diameter and orientation, as well as the yarn twist level on the yarn tensile properties were examined. For the yarns made from randomly oriented fine uniform nanofibers (e.g., diameter 359 nm) and beaded nanofibers, the tensile strength increased with increasing the yarn twist level. Higher fiber diameter (e.g., 634 nm) led to the tensile strength having an initial increase and then decrease trend. The modulus increased with the twist level for all the yarns studied. However, the elongation at break increased initially with the twist level and subsequently decreased. The orientation of aligned fibers within the fiber strip greatly influenced the yarn tensile properties. When the fibers were oriented along the fiber length direction, both tensile strength and modulus were the largest.

Highly-twisted, continuous nanofibre yarns prepared by a hybrid needle-needleless electrospinning technique

Nanofibres prepared by electrospinning have shown enormous potential for various applications. They are obtained predominantly in the form of nonwoven fibre webs. The 2-dimensional nonwoven feature and fragility have considerably confined their further processing into fabrics through knitting or weaving. Nanofibre yarns, which are nanofibre bundles with continuous length and a twist feature, show improved tensile strength, offering opportunities for making 3-dimensional fibrous materials with precisely controlled fibrous architecture, porous features and fabric dimensions. Despite a few techniques having been developed for electrospinning nanofibre yarns, they are chiefly based on the needle electrospinning technique, which often has low nanofibre productivity. In this study, we for the first time report a nanofibre yarn electrospinning technique which combines both needle and needleless electrospinning. A rotating intermediate ring collector was employed to directly collect freshly-electrospun nanofibres into a fibrous cone, which was further drawn and twisted into a nanofibre yarn. This novel system was able to produce high tenacity yarn (tensile strength 128.9 MPa and max strain 222.1%) at a production rate of 240 m h^-1, with a twist level up to 4700 twists per metre. The effects of various parameters, e.g. position of the electrospinning units, operating conditions and polymer concentration, on nanofibre and yarn production were examined.

Effects of grain size on the mosaic tilt and twist in InN films grown on GaN by metal-organic chemical vapor deposition

The structural property of InN films grown on Ga-face GaN layers by metal-organic chemical vapor deposition has been studied by high-resolution x-ray diffraction. The mosaic tilt and twist are found to be strongly dependent on the surface lateral grain size. The twist decreases with increasing grain size and finally approaches to a constant level. On the other hand, the mosaic tilt increases substantially when the grain size becomes large enough and exceeds the width of step terraces on the GaN surface, showing an important mechanism for the defect generation in the InN/GaN system with large out-of-plane lattice mismatch. (c) 2006 American Institute of Physics.

Consistency of superspace low energy equations of motion of 4D Type II superstring with Type II sigma model at tree-level

We derive the torsion constraints and show the consistency of equations of motion of four-dimensional Type II supergravity in superspace. with Type II sigma model. This is achieved by coupling the four-dimensional compactified Type II Berkovits' superstring to an N = 2 curved background and requiring that the sigma-model has superconformal invariance at tree-level. We compute this in a manifestly 4D N = 2 supersymmetric way. The constraints break the target conformal and SU(2) invariances and the dilaton will be a conformal, SU(2) x U(1) compensator. For Type II superstring in four dimensions, worldsheet supersymmetry requires two different compensators. One type is described by chiral and anti-chiral superfields. This compensator can be identified with a vector multiplet. The other Type II compensator is described by twist-chiral and twist-anti-chiral superfields and can be identified with a tensor hypermultiplet. Also, the superconformal invariance at tree-level selects a particular gauge, where the matter is fixed, but not the compensators. After imposing the reality conditions, we show that the Type II sigma model at tree-level is consistent with the equations of motion for Type II supergravity in the string gauge. (C) 2003 Elsevier B.V All rights reserved.

Reducing the global burden of depression : population level analysis of intervention cost-effectiveness in 14 world regions

International evidence on the cost and effects of interventions for reducing the global burden of depression remain scarce. Aims: To estimate the population-level cost-effectiveness of evidence-based depression interventions and their contribution towards reducing current burden. Method: Primary-care-based depression interventions were modelled at the level of whole populations in 14 epidemiological subregions of the world. Total population-level costs (in international dollars or I$) and effectiveness (disability adjusted life years (DALYs) averted) were combined to form average and incremental cost-effectiveness ratios. Results: Evaluated interventions have the potential to reduce the current burden of depression by 10–30%. Pharmacotherapy with older antidepressant drugs, with or without proactive collaborative care, are currently more cost-effective strategies than those using newer antidepressants, particularly in lower-income subregions. Conclusions: Even in resource-poor regions, each DALYaverted by efficient depression treatments in primary care costs less than 1 year of average per capita income, making such interventions a cost-effective use of health resources. However, current levels of burden can only be reduced significantlyif there is a substantialincrease substantial increase intreatment coverage.