Crystallographic variant selection in α–β brass

The transformation texture of α/β brass with a diffusional Widmanstätten α growth morphology has been investigated. Electron micrographs and electron backscattered diffraction was used to determine that the orientation relationship between the β phase and the α associated with nucleation at β grain boundaries was (44.3°) left angle bracket1 1 6right-pointing angle bracket. Crystallographic variant selection was observed across those prior β/β grain boundaries, but this has little effect on the transformation texture due to the crystal symmetry. The effect of the crystallographic variant selection on texture is further weakened by nucleation of diffusional transformed α in the grain interior.

Crystallographic variant selection in Ti-6Al-4V

Transformation textures in the two-phase alloy Ti–6Al–4V have been studied. Samples were heated into the fully β phase condition and then slow cooled to allow diffusional transformation to α. This produced a microstructure of grain boundary α encircling colonies of Widmanstätten α. Electron backscattered diffraction (EBSD) texture measurements showed that the α texture was markedly sharper than that calculated on a basis of equal variant probability, indicating that significant variant selection was occurring during diffusional transformation. Investigation of the α variants produced across prior β grain boundaries has shown that the selection of variants during transformation is highly dependant on the crystallography of those boundaries. The effect of this crystallographic variant selection on the transformation texture has been modelled.

Variant selection during the c-to-ab phase transformation in hot-rolled bainitic TRIP-aided steels

The variant selection phenomenon during the austenite to bainite phase transformation in hot-rolled TRIP-aided steels was quantitatively characterized at the level of individual austenite grains. The reconstruction of the electron backscatter diffraction maps provided evidence that bainite grows by packets of laths sharing a common {1 1 1}_y plane in the austenite. The affect of hot deformation is to reduce the number of packets that form. It is suggested that slip activity is important in understanding this effect.

Variant selection and intervariant crystallographic planes distribution in martensite in a Ti-6Al-4V alloy

The transformation texture was studied in a Ti-6Al-4V alloy for two microstructures produced through different phase transformation mechanisms (i.e. diffusional vs. displacive). Both microstructures revealed qualitatively similar crystallographic texture characteristics, having two main texture components with Euler angles of (90°, 90°, 0°) and (90°, 30°, 0°). However, the overall α texture strength was considerably weaker in the martensitic structure (i.e. displacive mechanism) compared with the α + β microstructure produced through slow cooling (i.e. diffusional mechanism). The intervariant boundary distribution in martensite mostly revealed five misorientations associated with the Burgers orientation relationship. The five-parameter boundary analysis also showed a very strong interface plane orientation texture, with interfaces terminated mostly on the prismatic planes {hki0}, when misorientation was ignored. The highest intervariant boundary populations belonged to the 63.26°/[10 553 ] and 60°/[112 0] misorientations, with length fractions of 0.38 and 0.3, respectively. The former was terminated on (41 3 0), and the latter was a symmetric tilt boundary, terminated on (1 011). The intervariant plane distribution in martensite was determined more by the constraints of the phase transformation than by the relative interface energies.

Experiment and theoretical prediction of martensitic transformation crystallography in a Ni–Mn–Ga ferromagnetic shape memory alloy

A detailed study of martensitic transformation crystallography and microstructural characteristics in the Ni53Mn25Ga22 ferromagnetic shape memory alloy (FSMA) was performed by both experimental observation and theoretical calculation. It is revealed that there are two microscopically twin-related martensitic variants with a misorientation of ∼82° around the 〈1 1 0〉_M axis in each initial austenite grain. The twin interface plane was determined to be {0.399 0.383 0.833}_M (1.79° away from {1 1 2}_M). The ratio of the amounts of the two variants inherited from one single austenite grain is about 1.70. The prevalent orientation relationship between austenite and martensite was found to be Kurdjumov–Sachs (K–S) relationship with (1 1 1)_A//(1 0 1)_M, [110]A//[111]_M. A successful explanation of the crystallographic features during martensitic transformation will shed light on the development of FSMAs with optimal performance.

Study of texture evolution in metastable beta-Ti alloy as a function of strain path and its effect on alpha transformation texture

Texture evolution in a low cost beta titanium alloy was studied for different modes of rolling and heat treatments. The alloy was cold rolled by unidirectional and multi-step cross rolling. The cold rolled material was either aged directly or recrystallized and then aged. The evolution of texture in alpha and beta phases were studied. The rolling texture of beta phase that is characterized by the gamma fiber is stronger for MSCR than UDR; while the trend is reversed on recrystallization. The mode of rolling affects alpha transformation texture on aging with smaller alpha lath size and stronger alpha texture in UDR than in MSCR. The defect structure in beta phase influences the evolution of a texture on aging. A stronger defect structure in beta phase leads to variant selection with the rolled samples showing fewer variants than the recrystallized samples.

Texture Evolution in Boron Modified Ti-6Al-4V Alloy

Owing to their high strength-to-weight ratio, excellent mechanical properties and corrosion resistance, titanium (Ti) and its alloys, especially (alpha+beta) alloys like Ti-6Al-4V is the backbone materials for aerospace, energy, and chemical industries. Trace boron addition (similar to 0.1 wt. %) to the alloy Ti-6Al-4V produces a reduction in as-cast grain size by roughly an order of magnitude resulting in enhanced ductility, higher stiffness, strength and good fracture resistance. Boron addition could also affect the evolution of texture and microstructure in the material. The solidification microstructures of Boron free as well as Boron containing Ti-6Al-4V are found to be almost homogeneous from periphery towards the center of as-cast ingot in terms of both alpha-colony size and distribution. Boron addition substantially reduces alpha-colony size (similar to 50-80 mu m). A gradual change in alpha texture from periphery towards the center has been observed with orientations close to specific texture components suggesting the formation of texture zones. The mechanism of texture evolution can be visualized as a result of variant selection during solidification through (alpha+beta) phase field.

Evolution of microstructure and texture in Ni49.4Ti38.6Hf12 shape memory alloy during hot rolling

This paper deals with the evolution of microstructure and texture during hot rolling of hafnium containing NiTi based shape memory alloy Ni49.4Ti38.6Hf12. The formation of the R-phase has been associated with the precipitation of (Ti,Hf)(2)Ni phase. The crystallographic texture of the parent phase B2 as well as the product phases R and B19' have been determined. It has been found that the variant selection during the B2 -> R phase transformation is quite strong compared to the case of the B2 -> B19' transformation. During deformation, the texture of the austenite phase evolves with strong Goss and Bs components. After transformation to martensitic structure, it gives rise to a 011]parallel to RD fiber. Microstructure and texture studies reveal the occurrence of partial dynamic recrystallization during hot rolling. Large strain heterogeneities that occur surrounding (Ti,Hf)(2)Ni precipitates are relieved through extended dynamic recovery instead of particle stimulated nucleation.

Crystallographic analysis of nano-structured bainitic steels

A 0.79C-1.5Si-1.98Mn-0.98Cr-0.24Mo-1.06Al-1.58Co (wt%) steel was isothermally heat treated at 200 and 350°C bainitic transformation temperatures. The microstructure was consisted of bainitic ferrite lath and retained austenite for both heat treatment conditions. The crystallographic analysis revealed that the bainitic ferrite laths are close to the Nishiyama-Wassermann orientation relationship with their parent austenite. The isothermal bainite transformation temperature has a significant effect on the retained austenite characteristics and the variant selection of the bainitic ferrite laths. In general, a decrease in the isothennal bainite transformation temperature refined the bainitic structure and weakened the variant selection.

Crystallographic analysis of nanobainitic steels

Electron back-scattered diffraction in conjunction with transmission electron microscopy was employed to investigate the crystallographic nature of bainitic laths formed at relatively low transformation temperatures where a nanostructured bainite forms. It was revealed that the bainitic ferrite laths are close to the Nishiyama–Wasserman orientation relationship with the parent austenite. Furthermore, the temperature showed a significant effect on the retained austenite characteristics and the variant selection of the bainitic ferrite laths. A decrease in temperature generally refined the bainitic structure and weakened the variant selection.

The martensitic transformation texture in Ti-6Al-4V

The transformation texture associated with martensite formation in the titanium alloy Ti- 6Al-4V has been investigated. Samples were heated into the fully b phase and quenched to form a microstructure of very fine a' martensite with no evidence of diffusional transformation at the prior b grain boundaries. EBSD texture measurements on the martensite showed that within each prior b grain, although typically all 12 variants of a’ were formed, the fractions of variants was far from uniform. The a’ texture was markedly different from values calculated using equal variant probability, also indicating that significant variant selection was occurring during martensitic transformation. This effect was modelled on the basis of elastic interaction between martensite events.

Enhanced mechanical response of an ultrafine grained Ti-6Al-4V alloy produced through warm symmetric and asymmetric rolling

An equiaxed ultrafine-grained (UFG) microstructure was successfully produced in a Ti-6Al-4V alloy with an average grain size of 110-230. nm through symmetric and asymmetric warm rolling of a martensitic starting microstructure. The UFG material displayed a combination of ultrahigh strength and ductility at room temperature. Compared with the conventional symmetric rolling, the asymmetric rolling process led to a more pronounced effect of microstructure refinement and a higher tensile ductility. The optimum mechanical response was obtained though the asymmetric rolling at 70% reduction, offering an ultimate tensile strength of 1365. MPa and a total elongation of ~23%. Apart from the magnitude of grain refinement, the inclination of basal texture component from the normal towards the rolling direction during asymmetric rolling and possible strain induced β to martensite transformation may concurrently contribute to a remarkable tensile strength-ductility balance.

Avaliação de variante somaclonal de porte baixo de bananeira 'Nanicão Jangada' (Musa sp) em duas densidades

Avaliou-se, sob duas densidades de plantio, um variante somaclonal de porte baixo de bananeira, comparando-o com a variedade Nanicão Jangada que lhe deu origem. Os materiais genéticos 'Nanicão Jangada'(controle) e o variante somaclonal representado pelas seleções 224 e 225 de um ensaio anterior, foram avaliados nos espaçamentos 2,0m X 2,0m (densidade 2500 plantas ha-1) e 3,0m X 2,0m (1666plantas ha-1), na Fazenda de Ensino e Pesquisa da Faculdade de Engenharia - UNESP, Campus de Ilha Solteira-SP. O ensaio foi conduzido em blocos ao acaso com cinco repetições, com utilização de mudas micropropagadas, sob irrigação por gotejamento, no período de dezembro de 1998 a março de 2001, com avaliação dos dois primeiros ciclos de produção. Constatou-se efeito da densidade e do ciclo sobre a produção estimada de frutos sendo que no cultivo mais denso, a média foi de 81,25 t.ha-1 no primeiro ciclo de produção e 67,93 t.ha-1 no segundo ciclo. No cultivo de menor densidade a produção estimada no primeiro ciclo foi de 51,35 t.ha-1 e 44,08 t.ha-1 no segundo. As seleções do variante de porte baixo apresentaram menor altura da planta e mostraram-se relativamente mais precoces e com produção semelhante a cv. Nanicão Jangada no primeiro ciclo. No segundo ciclo houve uma queda na produção do bananal, com maior intensidade para a seleção 225 do variante.

Replication of the association of common rs9939609 variant of FTO with increased BMI in an Australian adult twin population but no evidence for gene by environment (G x E) interaction

OBJECTIVE: To further investigate a common variant (rs9939609) in the fat mass- and obesity-associated gene (FTO), which recent genome-wide association studies have shown to be associated with body mass index (BMI) and obesity. DESIGN: We examined the effect of this FTO variant on BMI in 3353 Australian adult male and female twins. RESULTS: The minor A allele of rs9939609 was associated with an increased BMI (P=0.0007). Each additional copy of the A allele was associated with a mean BMI increase of approximately 1.04 kg/m(2) (approximately 3.71 kg). Using variance components decomposition, we estimate that this single-nucleotide polymorphism accounts for approximately 3% of the genetic variance in BMI in our sample (approximately 2% of the total variance). By comparing intrapair variances of monozygotic twins of different genotypes we were able to perform a direct test of gene by environment (G x E) interaction in both sexes and gene by parity (G x P) interaction in women, but no evidence was found for either. CONCLUSIONS: In addition to supporting earlier findings that the rs9939609 variant in the FTO gene is associated with an increased BMI, our results indicate that the associated genetic effect does not interact with environment or parity.

Direct Link-Aware Optimal Relay Selection and a Low Feedback Variant for Underlay CR

Cooperative relaying combined with selection has been extensively studied in the literature to improve the performance of interference-constrained secondary users in underlay cognitive radio (CR). We present a novel symbol error probability (SEP)-optimal amplify-and-forward relay selection rule for an average interference-constrained underlay CR system. A fundamental principle, which is unique to average interference-constrained underlay CR, that the proposed rule brings out is that the choice of the optimal relay is affected not just by the source-to-relay, relay-to-destination, and relay-to-primary receiver links, which are local to the relay, but also by the direct source-to-destination (SD) link, even though it is not local to any relay. We also propose a simpler, practically amenable variant of the optimal rule called the 1-bit rule, which requires just one bit of feedback about the SD link gain to the relays, and incurs a marginal performance loss relative to the optimal rule. We analyze its SEP and develop an insightful asymptotic SEP analysis. The proposed rules markedly outperform several ad hoc SD link-unaware rules proposed in the literature. They also generalize the interference-unconstrained and SD link-unaware optimal rules considered in the literature.