Trends in bus transit operations 1960-1974. Final report.

Transportation Department, Office of the Assistant Secretary for Policy and International Affairs, Washington, D.C.

La qualità erogata da un'azienda di trasporto collettivo in ambito urbano: calcolo del livello di servizio delle principali linee di ATC (BO)

Oggetto di questa tesi è lo studio della qualità del servizio di trasporto erogato che condiziona la qualità percepita dall’utente, poiché spesso proprio a causa di un errato processo di pianificazione e gestione della rete, molte aziende non sono in grado di consolidare un alto livello di efficienza che permetta loro di attrarre e servire la crescente domanda. Per questo motivo, si è deciso di indagare sugli aspetti che determinano la qualità erogata e sui fattori che la influenzano, anche attraverso la definizione di alcuni indicatori rappresentativi del servizio erogato. L’area di studio considerata è stata quella urbana di Bologna, e sono state prese in esame due linee di ATC, la 19 e la 27, caratterizzate entrambe da una domanda di trasporto molto elevata. L’interesse è ricaduto in modo particolare sugli aspetti legati alla regolarità del servizio, ovvero al rispetto della cadenza programmata delle corse e alla puntualità, ossia il rispetto dell’orario programmato delle stesse. Proprio da questi due aspetti, infatti, dipende in larga misura la percezione della qualità che gli utenti hanno del servizio di trasporto collettivo. Lo studio è stato condotto sulla base di dati raccolti attraverso due campagne di rilevamento, una effettuata nel mese di maggio dell’anno 2008 e l’altra nel mese di settembre dello stesso anno. La scelta del periodo, della zona e delle modalità di rilevamento è strettamente connessa all’obiettivo prefissato. Il servizio è influenzato dalle caratteristiche del sistema di trasporto: sia da quelle legate alla domanda che da quelle legate all’offerta. Nel caso della domanda di trasporto si considera l’influenza sul servizio del numero di passeggeri saliti e del tempo di sosta alle fermate. Nel caso dell’offerta di trasporto si osservano soprattutto gli aspetti legati alla rete di trasporto su cui si muovono gli autobus, analizzando quindi i tempi di movimento e le velocità dei mezzi, per vedere come le caratteristiche dell’infrastruttura possano condizionare il servizio. A tale proposito è opportuno dire che, mentre i dati della prima analisi ci sono utili per lo studio dell’influenza del tempo di sosta sull’intertempo, nella seconda analisi si vuole cercare di effettuare ulteriori osservazioni sull’influenza del tempo di movimento sulla cadenza, prendendo in esame altri elementi, come ad esempio tratti di linea differenti rispetto al caso precedente. Un’attenzione particolare, inoltre, verrà riservata alla verifica del rispetto della cadenza, dalla quale scaturisce la definizione del livello di servizio per ciò che riguarda la regolarità. Per quest’ultima verrà, inoltre, determinato anche il LOS relativo alla puntualità. Collegato al problema del rispetto della cadenza è il fenomeno dell’accodamento: questo si verifica quando i mezzi di una stessa linea arrivano contemporaneamente ad una fermata uno dietro l’altro. L’accodamento ha, infatti, origine dal mancato rispetto della cadenza programmata tra i mezzi ed è un’evidente manifestazione del mal funzionamento di un servizio di trasporto. Verrà infine condotta un’analisi dei fattori che possono influenzare le prestazioni del servizio di trasporto pubblico, così da collocare i dati ottenuti dalle operazioni di rilevamento in un quadro più preciso, capace di sottolineare alcuni elementi di criticità e possibili rapporti di causalità.

Summary Report: Stray Current Corrosion Control Evaluation

Report on various facilities at the Texas Medical Center that are impacted by metro light rail transit operations

Lot production size problem and simulation of urban transport

OBJECTIVES AND STUDY METHOD: There are two subjects in this thesis: “Lot production size for a parallel machine scheduling problem with auxiliary equipment” and “Bus holding for a simulated traffic network”. Although these two themes seem unrelated, the main idea is the optimization of complex systems. The “Lot production size for a parallel machine scheduling problem with auxiliary equipment” deals with a manufacturing setting where sets of pieces form finished products. The aim is to maximize the profit of the finished products. Each piece may be processed in more than one mold. Molds must be mounted on machines with their corresponding installation setup times. The key point of our methodology is to solve the single period lot-sizing decisions for the finished products together with the piece-mold and the mold-machine assignments, relaxing the constraint that a single mold may not be used in two machines at the same time. For the “Bus holding for a simulated traffic network” we deal with One of the most annoying problems in urban bus operations is bus bunching, which happens when two or more buses arrive at a stop nose to tail. Bus bunching reflects an unreliable service that affects transit operations by increasing passenger-waiting times. This work proposes a linear mathematical programming model that establishes bus holding times at certain stops along a transit corridor to avoid bus bunching. Our approach needs real-time input, so we simulate a transit corridor and apply our mathematical model to the data generated. Thus, the inherent variability of a transit system is considered by the simulation, while the optimization model takes into account the key variables and constraints of the bus operation. CONTRIBUTIONS AND CONCLUSIONS: For the “Lot production size for a parallel machine scheduling problem with auxiliary equipment” the relaxation we propose able to find solutions more efficiently, moreover our experimental results show that most of the solutions verify that molds are non-overlapping even if they are installed on several machines. We propose an exact integer linear programming, a Relax&Fix heuristic, and a multistart greedy algorithm to solve this problem. Experimental results on instances based on real-world data show the efficiency of our approaches. The mathematical model and the algorithm for the lot production size problem, showed in this research, can be used for production planners to help in the scheduling of the manufacturing. For the “Bus holding for a simulated traffic network” most of the literature considers quadratic models that minimize passenger-waiting times, but they are harder to solve and therefore difficult to operate by real-time systems. On the other hand, our methodology reduces passenger-waiting times efficiently given our linear programming model, with the characteristic of applying control intervals just every 5 minutes.

Towards a GIS-T database design and implementation for public transit planning: the case study of Dar-Es-salaam metropolitan city, Tanzania.

Dissertation submitted in partial fulfilment of the requirements for the Degree of Master of Science in Geospatial Technologies

Transit Assistance Program for Iowa, 1975

This inventory of transit services in Iowa covers urban transit, intercity passenger bus carriers and charter operators, taxicab operations, rural transit services and special services, and includes the results of questionnaire and interview surveys, and the resulting recommendations. The recommendations urge a centralized source of data and expertise, a public information program, the utilization of federal aid, the continuance of existing transit services with no dimunition of service level, the establishment of new services in communities of over 20,000 population, the sponsorship of demonstrations in communities with populations of 10,000 to 20,000, and the development and improvement of rural transit service. Based on state and local community experience, recommendations are made concerning revenue sources to support transit in Iowa, and four alternative state transit assistance programs are presented.

Robust rolling stock in rapid transit network

This paper focuses on the railway rolling stock circulation problem in rapid transit networks, in which frequencies are high and distances are relatively short. Although the distances are not very large, service times are high due to the large number of intermediate stops required to allow proper passenger flow. The main complicating issue is the fact that the available capacity at depot stations is very low, and both capacity and rolling stock are shared between different train lines. This forces the introduction of empty train movements and rotation maneuvers, to ensure sufficient station capacity and rolling stock availability. However, these shunting operations may sometimes be difficult to perform and can easily malfunction, causing localized incidents that could propagate throughout the entire network due to cascading effects. This type of operation will be penalized with the goal of selectively avoiding them and ameliorating their high malfunction probabilities. Critic trains, defined as train services that come through stations that have a large number of passengers arriving at the platform during rush hours, are also introduced. We illustrate our model using computational experiments drawn from RENFE (the main Spanish operator of suburban passenger trains) in Madrid, Spain. The results of the model, achieved in approximately 1 min, have been received positively by RENFE planners

Integration of Timetable Planning and Rolling Stock in Rapid Transit Networks

The aim of this paper is to propose an integrated planning model to adequate the offered capacity and system frequencies to attend the increased passenger demand and traffic congestion around urban and suburban areas. The railway capacity is studied in line planning, however, these planned frequencies were obtained without accounting for rolling stock flows through the rapid transit network. In order to provide the problem more freedom to decide rolling stock flows and therefore better adjusting these flows to passenger demand, a new integrated model is proposed, where frequencies are readjusted. Then, the railway timetable and rolling stock assignment are also calculated, where shunting operations are taken into account. These operations may sometimes malfunction, causing localized incidents that could propagate throughout the entire network due to cascading effects. This type of operations will be penalized with the goal of selectively avoiding them and ameliorating their high malfunction probabilities. Swapping operations will also be ensured using homogeneous rolling stock material and ensuring parkings in strategic stations. We illustrate our model using computational experiments drawn from RENFE (the main Spanish operator of suburban passenger trains) in Madrid, Spain. The results show that through this integrated approach a greater robustness degree can be obtained

Mass transit management : a handbook for small cities /

"DOT-T-88-11"--Pt. 3.

Advanced vehicle monitoring and communication systems for bus transit: benefits and economic feasibility. Final report.

Federal Transit Administration, Washington, D.C.

Capacity-based cost modeling for light rail and bus rapid transit systems

Choosing between Light Rail Transit (LRT) and Bus Rapid Transit (BRT) systems is often controversial and not an easy task for transportation planners who are contemplating the upgrade of their public transportation services. These two transit systems provide comparable services for medium-sized cities from the suburban neighborhood to the Central Business District (CBD) and utilize similar right-of-way (ROW) categories. The research is aimed at developing a method to assist transportation planners and decision makers in determining the most feasible system between LRT and BRT. ^ Cost estimation is a major factor when evaluating a transit system. Typically, LRT is more expensive to build and implement than BRT, but has significantly lower Operating and Maintenance (OM) costs than BRT. This dissertation examines the factors impacting capacity and costs, and develops cost models, which are a capacity-based cost estimate for the LRT and BRT systems. Various ROW categories and alignment configurations of the systems are also considered in the developed cost models. Kikuchi's fleet size model (1985) and cost allocation method are used to develop the cost models to estimate the capacity and costs. ^ The comparison between LRT and BRT are complicated due to many possible transportation planning and operation scenarios. In the end, a user-friendly computer interface integrated with the established capacity-based cost models, the LRT and BRT Cost Estimator (LBCostor), was developed by using Microsoft Visual Basic language to facilitate the process and will guide the users throughout the comparison operations. The cost models and the LBCostor can be used to analyze transit volumes, alignments, ROW configurations, number of stops and stations, headway, size of vehicle, and traffic signal timing at the intersections. The planners can make the necessary changes and adjustments depending on their operating practices. ^

Spatial-temporal mining of archived automatic vehicle location (AVL) data for transit service planning applications

An Automatic Vehicle Location (AVL) system is a computer-based vehicle tracking system that is capable of determining a vehicle's location in real time. As a major technology of the Advanced Public Transportation System (APTS), AVL systems have been widely deployed by transit agencies for purposes such as real-time operation monitoring, computer-aided dispatching, and arrival time prediction. AVL systems make a large amount of transit performance data available that are valuable for transit performance management and planning purposes. However, the difficulties of extracting useful information from the huge spatial-temporal database have hindered off-line applications of the AVL data. ^ In this study, a data mining process, including data integration, cluster analysis, and multiple regression, is proposed. The AVL-generated data are first integrated into a Geographic Information System (GIS) platform. The model-based cluster method is employed to investigate the spatial and temporal patterns of transit travel speeds, which may be easily translated into travel time. The transit speed variations along the route segments are identified. Transit service periods such as morning peak, mid-day, afternoon peak, and evening periods are determined based on analyses of transit travel speed variations for different times of day. The seasonal patterns of transit performance are investigated by using the analysis of variance (ANOVA). Travel speed models based on the clustered time-of-day intervals are developed using important factors identified as having significant effects on speed for different time-of-day periods. ^ It has been found that transit performance varied from different seasons and different time-of-day periods. The geographic location of a transit route segment also plays a role in the variation of the transit performance. The results of this research indicate that advanced data mining techniques have good potential in providing automated techniques of assisting transit agencies in service planning, scheduling, and operations control. ^

Improving robustness of rolling stock circulations in rapid transit networks

The rolling stock circulation depends on two different problems: the rolling stock assignment and the train routing problems, which up to now have been solved sequentially. We propose a new approach to obtain better and more robust circulations of the rolling stock train units, solving the rolling stock assignment while accounting for the train routing problem. Here robustness means that difficult shunting operations are selectively penalized and propagated delays together with the need for human resources are minimized. This new integrated approach provides a huge model. Then, we solve the integrated model using Benders decomposition, where the main decision is the rolling stock assignment and the train routing is in the second level. For computational reasons we propose a heuristic based on Benders decomposition. Computational experiments show how the current solution operated by RENFE (the main Spanish train operator) can be improved: more robust and efficient solutions are obtained

Robust infraestructure design in rapid transit rail systems

Incidents and rolling stock breakdowns are commonplace in rapid transit rail systems and may disrupt the system performance imposing deviations from planned operations. A network design model is proposed for reducing the effect of disruptions less likely to occur. Failure probabilities are considered functions of the amount of services and the rolling stock’s routing on the designed network so that they cannot be calculated a priori but result from the design process itself. A two recourse stochastic programming model is formulated where the failure probabilities are an implicit function of the number of services and routing of the transit lines.

Guided Bus Rapid Transit

Electrical Bus Rapid Transit (eBRT) is a charging electrical public transport which brings a clean, high performance, and affordable cost alternative from the conventional traffic vehicles which work with combustion and hybrid technology. These buses charge the battery in every bus stop to arrive at the next station. But, this charging system needs an appropriate infrastructure called pantograph, and it requires a high precision bus location to maintain battery lifetime, energy saving and charging time. To overcome this issue Vicomtech and Datik has planned a project based on computer vision to help to the driver to locate the vehicle in the correct place. In this document, we present a mono camera bus driver guided fast algorithm because these vehicles embedded computers do not support high computation and precision operations. In addition to the frequent lane sign, there are more accurate geometric beacons painted on the road to bring metric information to the vision system. This method uses segmentation to binarize the image discriminating the background space. Besides it detects, tracks and counts different lane mark contours in addition to classify each special painted mark. Besides it does not need any calibration task to calculate longitudinal and cross distances because we know the lane mark sizes.