Non-contact test set-up for aeroelasticity in a rotating turbomachine combining a novel acoustic excitation system with tip-timing

Due to trends in aero-design, aeroelasticity becomes increasingly important in modern turbomachines. Design requirements of turbomachines lead to the development of high aspect ratio blades and blade integral disc designs (blisks), which are especially prone to complex modes of vibration. Therefore, experimental investigations yielding high quality data are required for improving the understanding of aeroelastic effects in turbomachines. One possibility to achieve high quality data is to excite and measure blade vibrations in turbomachines. The major requirement for blade excitation and blade vibration measurements is to minimize interference with the aeroelastic effects to be investigated. Thus in this paper, a non-contact-and thus low interference-experimental set-up for exciting and measuring blade vibrations is proposed and shown to work. A novel acoustic system excites rotor blade vibrations, which are measured with an optical tip-timing system. By performing measurements in an axial compressor, the potential of the acoustic excitation method for investigating aeroelastic effects is explored. The basic principle of this method is described and proven through the analysis of blade responses at different acoustic excitation frequencies and at different rotational speeds. To verify the accuracy of the tip-timing system, amplitudes measured by tip-timing are compared with strain gage measurements. They are found to agree well. Two approaches to vary the nodal diameter (ND) of the excited vibration mode by controlling the acoustic excitation are presented. By combining the different excitable acoustic modes with a phase-lag control, each ND of the investigated 30 blade rotor can be excited individually. This feature of the present acoustic excitation system is of great benefit to aeroelastic investigations and represents one of the main advantages over other excitation methods proposed in the past. In future studies, the acoustic excitation method will be used to investigate aeroelastic effects in high-speed turbomachines in detail. The results of these investigations are to be used to improve the aeroelastic design of modern turbomachines.

Growth mechanisms and timing of emplacement of a vertically layered mafic intrusion in the feeder zone of an ocean island volcano (Fuerteventura, Canary islands)

Résumé pour le grand public L'île de Fuerteventura (Canaries) offre l'occasion rare d'observer les racines d'un volcan océanique édifié il y a 25 à 30 millions d'années et complètement érodé. On y voit de nombreux petits plutons de forme et composition variées, témoignant d'autant d'épisodes de l'activité magmatique. L'un de ces plutons, appelé PX1, présente une structure inhabituelle formée d'une alternance de bandes verticales d'épaisseur métrique à hectométrique de roches sombres de composition pyroxénilique ou gabbroïque. Les pyroxénites résultent clairement de l'accumulation de cristaux de pyroxènes et non de la simple solidification d'un magma? Se pose dès lors la question de la nature du processus qui a conduit à l'accumulation verticale de niveaux concentrés en pyroxènes. En effet, les litages pyroxénitiques classiques sont subhorizontaux, car ils résultent de l'accumulation gravitaire des cristaux séparés du magma dont ils cristalli¬sent par sédimentation. Cette étude vise à identifier et comprendre les mécanismes qui ont engendré ce Iitage minéralogique vertical et l'im¬portant volume de ces faciès cumulatifs. Nous nous sommes également intéressés aux conditions de pression et de température régnant au moment de la mise en place du pluton, ainsi qu'à sa durée de vie et à sa vitesse de refroidis¬sement. Enfin une approche géochimique nous a permis de préciser la nature de la source mantellique des magmas liés à cette activité magmatique. PX1 est en réalité un complexe filonien formé à des conditions de pression et de température de 1-2 kbar et 1050- 1100°C; sa construction a nécessité au moins 150 km3 de magma. L'alternance d'horizons gabbroïques et pyroxéniti¬ques représente des injections successives de magma sous la forme de filons verticaux, mis en place dans un contexte régional en extension. L'étude des orientations des minéraux dans ces faciès révèle que les horizons gabbroïques enregistrent l'extension régionale, alors que les pyroxénites sont générées par une compaction au sein du pluton. Ceci suggère que le régime des contraintes, qui était extensif lors de l'initiation de la mise en place de PX1, est pério¬diquement devenu compressif au sein même du pluton. Cette compression serait liée à des cycles de mise en place où la vitesse de croissance du pluton dépassait celle de l'extension régionale. La différenciation observée au sein de chaque horizon, depuis des pyroxénites riches en olivine jusqu'à des pyroxé¬nites à plagioclase interstitiel et des gabbros, ainsi que la composition géochimique des minéraux qui les constituent suggèrent que chaque filon vertical s'est mis en place à partir d'un magma de composition identique, puis a évolué indépendamment des autres en fonction du régime thermique et du régime des contraintes local. Lorsque le magma en train de cristalliser s'est trouvé en compression, le liquide résiduel a été séparé des cristaux déjà formés et extrait du système, laissant derrière lui une accumulation de cristaux dont la nature et les proportions dépendaient du stade de cristallisation atteint par le magma au moment de l'extraction. Ainsi, les niveaux de pyroxénites à olivine (premier minéral à cristalliser) ont été formés lorsque le magma correspondant était encore peu cristallisé; à l'inverse, les py¬roxénites riches en plagioclase (minéral plus tardif dans la séquence de cristallisation) et certains gabbros à caractère cumulatif résultent d'une compression tardive dans le processus de cristallisation du filon concerné. Les liquides résiduels extraits des niveaux pyroxénitiques sont rarement observés dans PX1, certaines poches et filonets de com¬position anorthositique pourraient en être les témoins. L'essentiel de ces liquides a probablement gagné des niveaux supérieurs du pluton, voire la surface du volcan. L'origine du régime compressif périodique affectant les filons en voie de cristallisation est attribuée aux injections suivantes de magma au sein du pluton, qui se sont succédées à un rythme plus rapide que la vitesse de consolidation des filons. Des datations U/Pb de haute précision sur des cristaux de zircon et de baddeleyite ainsi que40Ar/39Ar sur des cris¬taux d'amphibole révèlent une initiation de la mise en place de PX1 il y a 22.1 ± 0,7 Ma; celle-ci a duré quelque 0,48 ± 0,22 à 0,52 ± 0,29 Ma. Ce laps de temps est compatible avec celui nécessaire à la cristallisation des filons individuels, qui va de moins d'une année lors de l'initiation du magmatisme à 5 ans lors du maximum d'activité de PX1. La présence de cristaux résorbés enregistrant une cristallisation complexe suggère l'existence d'une chambre mag¬matique convective sous-jacente à PX1 et périodiquement rechargée. Les compositions isotopiques des roches étu¬diées révèlent une source mantellique profonde de type point chaud avec une contribution du manteau lithosphéri- que métasomatisé présent sous les îles Canaries. Résumé L'intrusion mafique Miocène PX1 fait partie du soubassement superficiel (0.15-0.2 GPa, 1100 °Q d'un volcan d'île océanique. La particularité de ce pluton est l'existence d'alternances d'unités de gabbros et de pyroxénites qui met¬tent en évidence un litage magmatique vertical (NNE-SSW). Les horizons gabbroiques et pyroxénitiques sont constitués d'unités de différenciation métriques qui suggèrent tine mise en place par injections périodiques de filons verticaux de magma formant un complexe filonien. Chaque filon vertical a subi une différenciation parallèle à un front de solidification sub-vertical parallèle aux bords du filon. Les pyroxénites résultent du fractionnement et de l'accumulation d'olivine ± clinopyroxene ± plagioclase à partir d'un magma basaltique faiblement alcalin et sont interprétées comme étant des imités de différenciation tronquées dont le liquide interstitiel a été extrait par compaction. L'orientation préférentielle des clinopyroxènes dans ces pyroxe- nites (obtenues par analyse EBSD et micro-tomographique) révèle une composante de cisaillement simple dans la genèse de ces roches, ce qui confirme cette interprétation. La compaction des pyroxénites est probablement causée par a mise en place de filons de magma suivants. Le liquide interstitiel expulsé est probablement par ces derniers. Les clinopyroxènes des gabbros, montrent une composante de cisaillement pure suggérant qu'ils sont affectés par une déformation syn-magmatique parallèle aux zones de cisaillement NNE-SSW observées autour de PX1 et liées au contexte tectonique Miocène d'extension régionale. Ceci suggère que les gabbros sont liés à des taux de mise en place faibles à la fin de cycles d'activité magmatique et sont peu ou pas affectés par la compaction. L'initiation et la géométrie de PX1 sont donc contrôlées par le contexte tectonique régional d'extension alors que les taux et les volumes de magma dépendent de facteurs liés à la source. Des taux d'injection élevés résultent probable¬ment en une croissance du pluton supérieure à la place crée par cette extension. Dans ce cas de figure, la propagation des nouveaux dykes et l'inaptitude du magma à circuler à travers les anciens dykes cristallisés pourrait causer une augmentation de la pression non-lithostatique sur ces derniers, exprimée par un cisaillement simple et l'expulsion du liquide interstitiel qu'ils contiennent (documenté par les zones de collecte anorthositiques). Les compositions en éléments majeurs et traces des gabbros et pyroxenites de PX1 sont globalement homogènes et dépendent de la nature cumulative des échantillons. Cependant, de petites variations des concentrations en éléments traces ainsi que les teneurs en éléments traces des bordures de clinopyroxenes suggèrent que ces derniers ont subi un processus de rééquilibrage et de cristallisation in situ. L'homogénéité des compositions chimiques des échantillons, ainsi que la présence de grains de clinopyroxene résorbés suggère que le complexe filonien PX1 s'est mis en place au dessus d'une chambre magmatique périodiquement rechargée dans laquelle la convection est efficace. Chaque filon est donc issu d'un même magma, mais a subi une différenciation par cristallisation in situ (jusqu'à 70% de fraction¬nement) indépendamment des autres. Dans ces filons cristallisés, les minéraux cumulatifs subissent un rééquilibrage partiel avec les liquide interstitiel avant que ce dernier ne soit expulsé lors de la compaction (mettant ainsi un terme à la différenciation). Ce modèle de mise en place signifie qu'un minimum de 150Km3 de magma est nécessaire à la genèse de PX1, une partie de ce volume ayant été émis par le 'Central Volcanic Complex' de Fuerteventura. Les rapports isotopiques radiogéniques mesurés révèlent la contribution de trois pôles mantelliques dans la genèse du magma formant PX1. Le mélange de ces pôles HIMU, DMM et EM1 refléterai l'interaction du point chaud Cana¬rien avec un manteau lithosphérique hétérogène métasomatisé. Les petites variations de ces rapports et des teneurs en éléments traces au sein des faciès pourrait refléter des taux de fusion partielle variable de la source, résultant en un échantillonnage variable du manteau lithosphérique métasomatisé lors de son interaction avec le point chaud. Des datations U/Pb de haute précision (TIMS) sur des cristaux de zircon et de baddeleyite extraits de gabbros de PX1 révèlent que l'initiation de la cristallisation du magma a eu lieu il y a 22.10±0.07 Ma et que l'activité magmatique a duré un minimum de 0.48 à 0.52 Ma. Des âges 40Ar/39Ar obtenus sur amphibole sont de 21.9 ± 0.6 à 21.8 ± 0.3 Ma, identiques aux âges U/Pb. La combinaison de ces méthodes de datations, suggère que le temps maximum nécessaire à PX1 pour se refroidir en dessous de la température de fermeture de l'amphibole est de 0.8Ma. Ceci signifie que la durée de vie de PX1 est de 520 000 à 800 000 ans. La coexistence de cristaux de baddeleyite et de zircon dans un gabbro est attribuée à son interaction avec un fluide riche en C02 relâché par les carbonatites encaissantes lors du métamorphisme de contact généré par la mise en place de PX1 environ 160 000 ans après le début de sa mise en place. Les durées de vie obtenue sont en accord avec le modèle de mise en place suggérant une durée de cristallisation poux chaque filon allant de 1 an à 5 ans. Abstract The Miocene PX1 gabbro-pyroxenite intrusion (Fuerteventura, Canary Islands), is interpreted as the shallow-level feeder-zone (0.15-0.2 GPa and 1100-1120°C), to an ocean island volcano. The particularity of PX1 is that it displays a NNE-SSW trending vertical magmatic banding expressed by alternating gabbro and pyroxeriite sequences. The gabbro and pyroxenite sequences consist of metre-thick differentiation units, which suggest emplacement by pe¬riodic injection of magma pulses as vertical dykes that amalgamated, similarly to a sub-volcanic sheeted dyke com¬plex. Individual dykes underwent internal differentiation following a solidification front (favoured by a significant lateral/horizontal thermal gradient) parallel to the dyke edges. Pyroxenitic layers result from the fractionation and accumulation of clinopyroxene ± olivine ± plagioclase crystals from a mildly alkaline basaltic liquid and are interpre¬ted as truncated differentiation sequences, from which residual melts were extracted by compaction. Clinopyroxene mineral orientation in pyroxenites (evidenced by EBSD and micro X-ray tomography analysis) display a marked pure shear component, supporting this interpretation. Compaction and squeezing of the crystal mush is ascribed to the incoming and inflating magma pulses. The resulting expelled interstitial liquid was likely collected and erupted along with the magma flowing through the newly injected dykes. Gabbro sequences represent crystallised coalesced magma batches, emplaced at lower rates at the end of eruptive cycles, and underwent minor melt extraction as evi¬denced by clinopyroxene orientations that record a simple shear component suggesting syn-magmatic deformation parallel to observed NNF.-SSW trending shear-zones induced by the regional tensional Miocene stress-field. The initiation and geometry of PX1 is controlled by the regional extensional tectonic regime whereas rates and vo¬lumes of magma depend on source-related factors. High injection rates are likely to induce intrusion growth rates larger than could be accommodated by the regional extension. In this case, dyke tip geometry and the inability of magma to circulate through previously emplaced and crystallised dykes could result in an increase of non-lithostatic pressure on previously emplaced mushy dyke walls; generating strong pure-shear compaction and interstitial melt expulsion within the feeder-zone as recorded by the cumulitic pyroxenite bands and anorthositic collection zones. The whole-rock major and trace-element chemistry of PX1 gabbros and pyroxenites is globally homogeneous and controlled by the cumulate nature of the samples (i.e. on the modal proportions of olivine, pyroxene, plagioclase and oxides). However, small variations of whole-rock trace-element contents as well as trace-element contents of clinopyroxene rims suggest that in-situ re-equilibration and crystallisation has occurred. Additionally, the global homogeneity and presence of complex zoning of rare resorbed clinopyroxene crystals suggest that the PX1 feeder- zone overlies a periodically replenished and efficiently mixed magma chamber. Each individual dyke of magma thus originated from a compositionally constant mildly alkaline magma and differentiated independently from the others reaching up to 70% fractionation. Following dyke arrest these are affected by interaction with the trapped interstitial liquid prior to its compaction-linked expulsion (thus stopping the differentiation process). This emplacement model implies that minimum amount of approximately 150 km3 of magma is needed to generate PX1, part of it having been erupted through the overlying Central Volcanic Complex of Fuerteventura. The radiogenic isotope ratios of PX1 samples reveal the contribution on three end-members during magma genesis. This mixing of the H1MU, EMI and DMM end-members could reflect the interaction of the deep-seated Canarian mantle plume with a heterogeneous metasomatic and sepentininsed lithospheric mantle. Additionally, the observed trace-element and isotopic variations within the same fades groups could reflect varying degrees of partial melting of the source region, thus tapping more or less large areas of the metasomatised lithospheric mantle during interac¬tion with the plume. High precision ID-TIMS U/Pb zircon and baddeleyite ages from the PX1 gabbro samples, indicate initiation of magma crystallisation at 22.10 ± 0.07 Ma. The magmatic activity lasted a minimum of 0.48 to 0.52 Ma. 40Ar/39Ar amphibole ages are of 21.9 ± 0.6 to 21.8 ± 0.3, identical within errors to the U/Pb ages. The combination of the 40Ar/39Ar and U/Pb datasets imply that the maximum amount of time PX1 took to cool below amphibole Tc is 0.8 Ma, suggesting PX1 lifetime of 520 000 to 800 000 years. On top of this, the coexistence of baddeleyite and zircon in a single sample is ascribed to the interaction of PX1 with C02-rich carbonatite-derived fluids released from the host-rock carbonatites during contact metamorphism 160 000 years after PX1 initiation. These ages are in agreement with the emplacement model, implying a crystallisation time of less than 1 to 5 years for individual dykes.

Timing, magnitude, and location of initial soluble aluminum injuries to mungbean roots

Despite a century's knowledge that soluble aluminum (Al) is associated with acid soils and poor plant growth, it is still uncertain how Al exerts its deleterious effects. Hypotheses include reactions of Al with components of the cell wall, plasmalemma, or cytoplasm of cells close to the root tip, thereby reducing cell expansion and root growth. Digital microscopy was used to determine the initial injuries of soluble Al to mungbean (Vigna radiata L.) roots. Roots of young seedlings were marked with activated carbon particles and grown in 1 mm CaCl2 solution at pH 6 for ca. 100 min (control period), and AlCl3 solution was added to ensure a final concentration of 50 muM Al (pH 4). Further studies were conducted on the effects of pH 4 with and without 50 muM Al. Four distinct, but possibly related, initial detrimental effects of soluble Al were noted. First, there was a 56-75% reduction in the root elongation rate, first evident 18-52 min after the addition of Al, root elongation continuing at a decreased rate for ca. 20 It. Decreasing solution pH from 6 to 4 increased the root elongation rate 4-fold after 5 min, which decreased to close to the original rate after 130 min. The addition of Al during the period of rapid growth at pH 4 reduced the root elongation rate by 71% 14 min after the addition of Al. The activated carbon marks on the roots showed that, during the control period, the zone of maximum root growth occurred at 2,200-5,100 mum from the root tip (i.e. the cell elongation zone). It was there that Al first exerted its detrimental effect and low pH increased root elongation. Second, soluble Al prevented the progress of cells from the transition to the elongation phase, resulting in a considerable reduction of root growth over the longer term. The third type of soluble Al injury occurred after exposure for ca. 4 h to 50 mum Al when a kink developed at 2,370 mum from the root tip. Fourth, ruptures of the root epidermal and cortical cells at 1,900-2,300 mum from the tip occurred greater than or equal to4.3 h after exposure to soluble Al. The timing and location of Al injuries support the contention that Al initially reduces cell elongation, thus decreasing root growth and causing damage to epidermal and cortical cells.

Syllable-timing in Brazilian Portuguese: uma crítica a Roy Major

This paper reintroduces the discussion about stress-timing in Brazilian Portuguese (BP). It begins by surveying some phonetic and phonological issues raised by the syllable- vs stress-timed dichotomy which culminated with the emergence of the p-center notion. Strict considerations of timing of V-V units and stress groups are taken into account to analyze the long term coupling of two basic oscillators (vowel and stress flow). This coupling allows a two-parameter characterization of language rhythms (coupling strength and speech rate) revealing that BP utterances present a high-degree of syllable-timing. A comparison with other languages, including European Portuguese, is also presented. The results analyzed indicate that Major's arguments for considering Portuguese (sic) as stress-timing are misleading.

Tempo de reação, tempo de movimento e aquisição de timing antecipatorio em idosos

Universidade Estadual de Campinas. Faculdade de Educação Física

Timing and sequence of primary tooth eruption in children with cleft lip and palate

OBJECTIVE: To determine the timing and sequence of eruption of primary teeth in children with complete bilateral cleft lip and palate. MATERIAL AND METHODS: This cross-sectional study was conducted at the Hospital for Rehabilitation of Craniofacial Anomalies of the University of São Paulo, Bauru, SP, Brazil, with a sample of 395 children (128 girls and 267 boys) aged 0 to 48 months, with complete bilateral cleft lip and palate. RESULTS: Children with complete bilateral clefts presented a higher mean age of eruption of all primary teeth for both arches and both genders, compared to children without clefts. This difference was statistically signifcant for all teeth, except for the maxillary first molar. Mean age of eruption of most teeth was lower for girls compared to boys. The greatest delay was found for the maxillary lateral incisor, which was the eighth tooth of children with clefts of both genders. Analyzing by gender, the maxillary lateral incisor was the eighth tooth to erupt in girls and the last in boys. CONCLUSION: The results suggest an interference of the cleft on the timing and sequence of eruption of primary teeth.

Evaluation of timing and responses to physiotherapeutic treatment

In several treatment regimens, the recognition of chronobiology contributes to the therapeutic process through the effective use of temporization protocols. The purpose of the present study was to evaluate the relationship between the tic treatment and the time of day when such treatment was performed, as well as the chronotype of orthopedic and rheumatologic patients in a clinical physiotherapy school. The population studied was treated in the morning and evening periods. The patients were divided into three groups of pathologies with similar treatments, which were as follows: syndrome of shoulder impact (n=33), knee artrosis (n=17), and lombalgia (n=23). At the end of ten treatment sessions, data concerning pain, percentage of subjective improvement, chronotype and age were compared. At the end of the study, it was observed that the time of day when treatment was performed influenced the results of individuals treated in the evenings but had no influence on the individuals treated in the morning. In addition, the evening schedule was the most well suited for intermediate individuals.

Analysis of the tip roundness effects on the micro- and macroindentation response of elastic-plastic materials

In this work, the effects of indenter tip roundness oil the load-depth indentation curves were analyzed using finite element modeling. The tip roundness level was Studied based on the ratio between tip radius and maximum penetration depth (R/h(max)), which varied from 0.02 to 1. The proportional Curvature constant (C), the exponent of depth during loading (alpha), the initial unloading slope (S), the correction factor (beta), the level of piling-up or sinking-in (h(c)/h(max)), and the ratio h(max)/h(f) are shown to be strongly influenced by the ratio R/h(max). The hardness (H) was found to be independent of R/h(max) in the range studied. The Oliver and Pharr method was successful in following the variation of h(c)/h(max) with the ratio R/h(max) through the variation of S with the ratio R/h(max). However, this work confirmed the differences between the hardness values calculated using the Oliver-Pharr method and those obtained directly from finite element calculations; differences which derive from the error in area calculation that Occurs when given combinations of indented material properties are present. The ratio of plastic work to total work (W(p)/W(t)) was found to be independent of the ratio R/h(max), which demonstrates that the methods for the Calculation of mechanical properties based on the *indentation energy are potentially not Susceptible to errors caused by tip roundness.

Cell Therapy Attenuates Cardiac Dysfunction Post Myocardial Infarction: Effect of Timing, Routes of Injection and a Fibrin Scaffold

Background: Cell therapy approaches for biologic cardiac repair hold great promises, although basic fundamental issues remain poorly understood. In the present study we examined the effects of timing and routes of administration of bone marrow cells (BMC) post-myocardial infarction (MI) and the efficacy of an injectable biopolymer scaffold to improve cardiac cell retention and function. Methodology/Principal Findings: (99m)Tc-labeled BMC (6x10(6) cells) were injected by 4 different routes in adult rats: intravenous (IV), left ventricular cavity (LV), left ventricular cavity with temporal aorta occlusion (LV(+)) to mimic coronary injection, and intramyocardial (IM). The injections were performed 1, 2, 3, or 7 days post-MI and cell retention was estimated by gamma-emission counting of the organs excised 24 hs after cell injection. IM injection improved cell retention and attenuated cardiac dysfunction, whereas IV, LV or LV* routes were somewhat inefficient (< 1%). Cardiac BMC retention was not influenced by timing except for the IM injection that showed greater cell retention at 7 (16%) vs. 1, 2 or 3 (average of 7%) days post-MI. Cardiac cell retention was further improved by an injectable fibrin scaffold at day 3 post-MI (17 vs. 7%), even though morphometric and function parameters evaluated 4 weeks later displayed similar improvements. Conclusions/Significance: These results show that cells injected post-MI display comparable tissue distribution profile regardless of the route of injection and that there is no time effect for cardiac cell accumulation for injections performed 1 to 3 days post-MI. As expected the IM injection is the most efficient for cardiac cell retention, it can be further improved by co-injection with a fibrin scaffold and it significantly attenuates cardiac dysfunction evaluated 4 weeks post myocardial infarction. These pharmacokinetic data obtained under similar experimental conditions are essential for further development of these novel approaches.

Tidal-amplitude rhythms of larval release: variable departure from presumed optimal timing among populations of the mottled shore crab

It is widely assumed that optimal timing of larval release is of major importance to offspring survival, but the extent to which environmental factors entrain synchronous reproductive rhythms in natural populations is not well known. We sampled the broods of ovigerous females of the common shore crab Pachygrapsus transversus at both sheltered and exposed rocky shores interspersed along a so-km coastline, during four different periods, to better assess inter-population differences of larval release timing and to test for the effect of wave action. Shore-specific patterns were consistent through time. Maximum release fell within 1 day around syzygies on all shores, which matched dates of maximum tidal amplitude. Within this very narrow range, populations at exposed shores anticipated hatching compared to those at sheltered areas, possibly due to mechanical stimulation by wave action. Average departures from syzygial release ranged consistently among shores from 2.4 to 3.3 days, but in this case we found no evidence for the effect of wave exposure. Therefore, processes varying at the scale of a few kilometres affect the precision of semilunar timing and may produce differences in the survival of recently hatched larvae. Understanding the underlying mechanisms causing departures from presumed optimal release timing is thus important for a more comprehensive evaluation of reproductive success of invertebrate populations.

Retention-favorable timing of propagule release in barnacles and periwinkles

Recent studies on the ecology of marine larvae suggest that retention near coastal areas and self-recruitment are probably much more common than previously thought. In light of this, the advective potential of pelagic stages can be partially determined by the timing of propagule release. We sampled the upper-shore levels of a subtropical coastline in southeastern Brazil to examine the temporal patterns of propagule release for the common barnacle Chthamalus bisinuatus and the periwinkle Nodilittorina lineolata. The release timing in both species was very consistent between sites a few kilometers apart. Barnacles released nauplii in a rhythmic pattern, mostly coinciding with neap tides, when the speed of tidal currents was lowest. There was no variation in propagule release in relation to diel or flood-ebb tidal cycles. Periwinkles released propagules in a very irregular pattern, which remarkably matched a time series of wave heights. Egg capsules were released during periods of rough seas, when onshore surface currents were expected to prevail. Eggs were released mostly during ebb tides, and there was no diel variation. Propagule release rhythms are usually viewed as a means to ensure fast offshore advection, thus avoiding presumed hazardous conditions for larvae. However, propagule release strategies in these upper-shore species would more likely contribute to the retention of offspring close to parental stocks.

Intercepting moving targets: does memory from practice in a specific condition of target displacement affect movement timing?

This investigation aimed at assessing the extent to which memory from practice in a specific condition of target displacement modulates temporal errors and movement timing of interceptive movements. We compared two groups practicing with certainty of future target velocity either in unchanged target velocity or in target velocity decrease. Following practice, both experimental groups were probed in the situations of unchanged target velocity and target velocity decrease either under the context of certainty or uncertainty about target velocity. Results from practice showed similar improvement of temporal accuracy between groups, revealing that target velocity decrease did not disturb temporal movement organization when fully predictable. Analysis of temporal errors in the probing trials indicated that both groups had higher timing accuracy in velocity decrease in comparison with unchanged velocity. Effect of practice was detected by increased temporal accuracy of the velocity decrease group in situations of decreased velocity; a trend consistent with the expected effect of practice was observed for temporal errors in the unchanged velocity group and in movement initiation at a descriptive level. An additional point of theoretical interest was the fast adaptation in both groups to a target velocity pattern different from that practiced. These points are discussed under the perspective of integration of vision and motor control by means of an internal forward model of external motion.

Effects of mechanical properties, residual stress and indenter tip geometry on instrumented indentation data in thin films

In this work, an axisymmetric two-dimensional finite element model was developed to simulate instrumented indentation testing of thin ceramic films deposited onto hard steel substrates. The level of film residual stress (sigma(r)), the film elastic modulus (E) and the film work hardening exponent (n) were varied to analyze their effects on indentation data. These numerical results were used to analyze experimental data that were obtained with titanium nitride coated specimens, in which the substrate bias applied during deposition was modified to obtain films with different levels of sigma(r). Good qualitative correlation was obtained when numerical and experimental results were compared, as long as all film properties are considered in the analyses, and not only sigma(r). The numerical analyses were also used to further understand the effect of sigma(r) on the mechanical properties calculated based on instrumented indentation data. In this case, the hardness values obtained based on real or calculated contact areas are similar only when sink-in occurs, i.e. with high n or high ratio VIE, where Y is the yield strength of the film. In an additional analysis, four ratios (R/h(max)) between indenter tip radius and maximum penetration depth were simulated to analyze the combined effects of R and sigma(r) on the indentation load-displacement curves. In this case, or did not significantly affect the load curve exponent, which was affected only by the indenter tip radius. On the other hand, the proportional curvature coefficient was significantly affected by sigma(r) and n. (C) 2010 Elsevier B.V. All rights reserved.

Timing and Dose of Statin Therapy Define Its Impact on Inflammatory and Endothelial Responses During Myocardial Infarction

Objective-Clinical trials of statins during myocardial infarction (MI) have differed in their therapeutic regimes and generated conflicting results. This study evaluated the role of the timing and potency of statin therapy on its potential mechanisms of benefit during MI. Methods and Results-ST-elevation MI patients (n = 125) were allocated into 5 groups: no statin; 20, 40, or 80 mg/day simvastatin starting at admission; or 80 mg/day simvastatin 48 hours after admission. After 7 days, all patients switched their treatment to 20 mg/day simvastatin for an additional 3 weeks and then underwent flow-mediated dilation in the brachial artery. As of the second day, C-reactive protein (CRP) differed between non-statin users (12.0 +/- 4.1 mg/L) and patients treated with 20 (8.5 +/- 4.0 mg/L), 40 (3.8 +/- 2.5 mg/L), and 80 mg/day (1.4 +/- 1.5 mg/L), and the daily differences remained significant until the seventh day (P < 0.0001). The higher the statin dose, the lower the elevation of interleukin-2 and tumor necrosis factor-alpha, the greater the reduction of 8-isoprostane and low-density lipoprotein(-), and the greater the increase in nitrate/nitrite levels during the first 5 days (P < 0.001). Later initiation of statin was less effective than its early introduction in relation to attenuation of CRP, interleukin-2, tumor necrosis factor-alpha, 8-isoprostane, and low-density lipoprotein(-), as well as in increase in nitrate/nitrite levels (P < 0.0001). At the 30th day, there was no longer a difference in lipid profile or CRP between groups; the flow-mediated dilation, however, was proportional to the initial statin dose and was higher for those who started the treatment early (P = 0.001). Conclusion-This study demonstrates that the timing and potency of statin treatment during MI are key elements for their main mechanisms of benefit.

Hitting a moving target: Perception and action in the timing of rapid interceptions

Different interceptive tasks and modes of interception (hitting or capturing) do not necessarily involve similar control processes. Control based on preprogramming of movement parameters is possible for actions with brief movement times but is now widely rejected; continuous perceptuomotor control models are preferred for all types of interception. The rejection of preprogrammed control and acceptance of continuous control is evaluated for the timing of rapidly executed, manual hitting actions. It is shown that a preprogrammed control model is capable of providing a convincing account of observed behavior patterns that avoids many of the arguments that have been raised against it. Prominent continuous perceptual control models are analyzed within a common framework and are shown to be interpretable as feedback control strategies. Although these models can explain observations of on-line adjustments to movement, they offer only post hoc explanations for observed behavior patterns in hitting tasks and are not directly supported by data. It is proposed that rapid manual hitting tasks make up a class of interceptions for which a preprogrammed strategy is adopted-a strategy that minimizes the role of visual feedback. Such a strategy is effective when the task demands a high degree of temporal accuracy.