Influence of 3A molecular sieve to tetrahydrofuran(THF) hydrate formation

Visual observation of the THF hydrate formation process in the presence of a 3A molecular sieve has been made at normal atmosphere and below a temperature of zero by microscopy. The results indicate that a 3A molecular sieve can induce the nucleation of the THF hydrate and promote the THF hydrate growth. With the existence of a 3A molecular sieve, the growth rate of THF hydrate is between 0.01 and 0.05 mu m/s. In comparison with the system without any 3A molecular sieve, the growth rate increases about 4 nm/s. After the THF hydrate grows into megacryst, the crystals will recombine and partially change under the same condition.

Multiwall carbon nanotubes from pyrolysis of tetrahydrofuran

Multiwalled carbon nanotubes have been prepared by pyrolysing tetrahydrofuran (THF) in the presence of nickelocene. Pyrolysis of the precursor mixture has been achieved at temperature as low as 600 degrees C. In this simple approach no carrier gas has been used. The yield of purified carbon nanotubes is found to be more than 65%. Characterization of the as-prepared and purified nanotubes are done by Xray diffraction, scanning electron microscopy, high-resolution transmission electron microscopy and Raman spectra.

Influence of 5A-Type Zeolite Powder on Tetrahydrofuran Hydrate Formation and Dissociation Process

Visual observations of tetrahydrofuran (THF) hydrate formation and dissociation processes with 5A-type zeolite powder were made at normal atmospheric conditions and below zero temperature by microscope. Results indicate that 5A-type zeolite powder can promote THF hydrate growth. At the same time, in the presence of 5A-type zeolite, agglomerated crystals and vein-like crystals of THF hydrate were also formed. SA-type zeolite powder increases the crystallization temperature and decreases the dissociation temperature. The particle size distribution of 5A-type zeolite powder influences THF hydrate formation and its dissociation characteristics significantly.

RING-OPENING POLYMERIZATION OF TETRAHYDROFURAN WITH RARE EARTH-CONTAINED CATALYSTS

Rare earth trifluoroacetates, Ln(CF3CO2)(3) (Ln = thirteen rare earth elements), combined with R(n)AlH(3-n) (R = methyl, octyl, n = 3; R = ethyl, i-Butyl, n = 2, 3) were used as catalysts for the polymerization of tetrahydrofuran (THF). The activity increased by adding propylene oxide (PO), as a promoter, to the polymerization system, producing high molecular weight polytetrahydrofuran (PTHF). The effects of Ln, PO/Ln, and Al/Ln, and others on the polymerization of THF were also studied. (C) 1993 John Wiley & Sons, Inc.

Densities, speeds of sound, isentropic compressibilities, refractive indices and viscosities of binary mixtures of tetrahydrofuran with hydrocarbons at 303.15 K

Isentropic compressibilities, Rao's molar sound functions, molar refractions, excess isentropic compressibilities, excess molar volumes, viscosity deviations and excess Gibbs energies of activation of viscous flow for seven binary mixtures of tetrahydrofuran (THF) with cyclohexane, methylcyclohexane, n-hexane, benzene, toluene, p-xylene and propylbenzene over the entire range of composition at 303.15 K have been derived from experimental densities, speeds of sound, refractive indices and viscosities. The excess partial molar volumes of THF in different solvents have been estimated. The experimental results have been analyzed in terms of the Prigogine–Flory–Patterson theory.

Estudo de N-metilformamida em meio aquoso e não aquoso (THF)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

On the hydrogen bonding between N-methylformamide and acetone and tetrahydrofuran

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

2 '-Deoxyguanosine, 2 '-deoxycytidine, and 2 '-deoxyadenosine adducts resulting from the reaction of tetrahydrofuran with DNA bases

A recent study showed that tetrahydrofuran (THF), a widely used solvent, is carcinogenic in experimental animals. Despite its carcinogenic activity, there is a paucity of information regarding cellular toxicity, biomolecular damage, and genotoxicity induced by THF. We describe here the structural characterization of adducts produced by the reaction of oxidized THF with 2'-deoxyguanosine (dGuo-THF 1 and dGuo-THF 2), 2'-deoxyadenosine (dAdo-THF), and 2'-deoxycytidine (dCyd-THF). Adducts were isolated from in vitro reactions by reverse-phase HPLC and fully characterized on the basis of spectroscopic measurements. The stable derivatives obtained by the reduction of adducts with NaBH4 ( the case of dGuo-THF 1, dCyd-THF, and dAdo-THF) and the stable adduct dGuo-THF 2 were used as standards for optimization of chromatographic separations for adduct detection in DNA through HPLC/ESI/MSMS. Using this methodology, we successfully detected the four adducts in calf thymus DNA reacted with oxidized THF. The present study also provides evidence that rat liver microsomal monooxigenases oxidize THF to the reactive electrophilic compounds that are able to damage the DNA molecule, as indicated by a significant increase in adduct dGuo-THF 1 level when NADPH was added to the THF/ microsomes/dGuo incubation mixtures. Our data point to DNA-THF adducts as possible contributing factors to the toxicological effects of THF exposure.

Monte Carlo simulation of water-tetrahydrofuran mixtures

Monte Carlo simulations of water-tetrahydrofuran (THF) mixtures were performed in the isothermal-isobaric ensemble (NPT) at T = 298 K and p = 1 atm. The interaction energy was calculated using the TIP4P model for water and a five-site united atom representation for the THF molecule. The potential energy surfaces for water-THF interactions were obtained by using combining rules and the original potential functions used for pure liquids. Theoretical values obtained for the average interaction energy as a function of concentration are in good agreement with available experimental data. Results from the partitioning of the total interaction energy into water-water, water-THF and THF-THF contributions are presented. These results are useful to distinguish between the quantitative contributions of these molecular interactions to the energetic behavior of the water-THF mixing process. The radial distribution functions for HW-OTHF and OW-OTHF site-site interactions show the salient features of hydrogen-bonded liquids. Comparison of the average number of water-water complexes interacting through hydrogen bonding in water-THF and water-methanol mixtures shows an enhancement of the water-water coordination number in a THF rich environment. © 1995.

Mesure de sections efficaces absolues vibrationnelles pour la collision d’électrons de basse énergie (1-19 eV) avec le tétrahydrofurane (THF) condensé

Résumé: Ce mémoire de maîtrise est une étude des probabilités d’interactions (sections efficaces) des électrons de basse énergie avec une molécule d’intérêt biologique. Cette molécule est le tétrahydrofurane (THF) qui est un bon modèle de la molécule constituant la colonne vertébrale de l’ADN; le désoxyribose. Étant donné la grande quantité d’électrons secondaires libérés lors du passage des radiations à travers la matière biologique et sachant que ceux-ci déposent la majorité de l’énergie, l’étude de leurs interactions avec les molécules constituant l’ADN devient rapidement d’une grande importance. Les mesures de sections efficaces sont faites à l’aide d’un spectromètre à haute résolution de pertes d’énergie de l’électron. Les spectres de pertes d’énergie de l’électron obtenus de cet appareil permettent de calculer les valeurs de sections efficaces pour chaque vibration en fonction de l’énergie incidente de l’électron. L’article présenté dans ce mémoire traite de ces mesures et des résultats. En effet, il présente et explique en détail les conditions expérimentales, il décrit la méthode de déconvolution qui est utilisée pour obtenir les valeurs de sections efficaces et il présente et discute des 4 résonances observées dans la dépendance en énergie des sections efficaces. En effet, cette étude a permis de localiser en énergie 4 résonances et celles-ci ont toutes été confirmées par des recherches expérimentales et théoriques antérieures sur le sujet des collisions électrons lents-THF. En outre, jamais ces résonances n’avaient été observées simultanément dans une même étude et jamais la résonance trouvée à basse énergie n’avait été observée avec autant d’intensité que cette présente étude. Cette étude a donc permis de raffiner notre compréhension fondamentale des processus résonants impliqués lors de collisions d’électrons secondaires avec le THF. Les valeurs de sections efficaces sont, quant à elles, très prisées par les théoriciens et sont nécessaires pour les simulations Monte Carlo pour prédire, par exemple, le nombre d’ions formées après le passage des radiations. Ces valeurs pourront justement être utilisées dans les modèles de distribution et dépôt d’énergie au niveau nanoscopique dans les milieux biologiques et ceux-ci pourront éventuellement améliorer l’efficacité des modalités radiothérapeutiques.

Polyurethane (PU) scaffolds prepared by solvent casting/particulate leaching (SCPL) combined with centrifugation

This article reports an enhanced solvent casting/particulate (salt) leaching (SCPL) method developed for preparing three-dimensional porous polyurethane (PU) scaffolds for cardiac tissue engineering. The solvent for the preparation of the PU scaffolds was a mixture of dimethylformamide (DFM) and tetrahydrofuran (THF). The enhanced method involved the combination of a conventional SCPL method and a step of centrifugation, with the centrifugation being employed to improve the pore uniformity and the pore interconnectivity of scaffolds. Highly porous three-dimensional scaffolds with a well interconnected porous structure could be achieved at the polymer solution concentration of up to 20% by air or vacuum drying to remove the solvent. When the salt particle sizes of 212-295, 295-425, or 425-531 µm and a 15% w/v polymer solution concentration were used, the porosity of the scaffolds was between 83-92% and the compression moduli of the scaffolds were between 13 kPa and 28 kPa. Type I collagen acidic solution was introduced into the pores of a PU scaffold to coat the collagen onto the pore walls throughout the whole PU scaffold. The human aortic endothelial cells (HAECs) cultured in the collagen-coated PU scaffold for 2 weeks were observed by scanning electron microscopy (SEM). It was shown that the enhanced SCPL method and the collagen coating resulted in a spatially uniform distribution of cells throughout the collagen-coated PU scaffold.

Preparation temperature effect on the synthesis of various carbon nanostructures

Various carbon nanostructures (CNs) have been prepared by a simple deposition technique based on the pyrolysis of a new carbon source material tetrahydrofuran (THF) mixed with ferrocene using quartz tube reactor in the temperature range 700-1100 degrees C. A detailed study of how the synthesis parameter such as growth temperature affects the morphology of the carbon nanostructures is presented. The obtained CNs are investigated by scanning electron microscope (SEM), X-ray diffraction (XRD), electron dispersive scattering (EDS)thermogravimetry analysis (TGA), Raman and transmission electron microscope (TEM). It is observed that at 700 degrees C. normal CNTs are formed. Iron filled multi-walled carbon nanotubes (MWCNTs) and carbon nanoribbons (CNRs) are formed at 950 degrees C. Magnetic characterization of iron filled MWCNTs and CNRs studied at 300 K by superconducting quantum interference device (SQUID) reveals that these nanostructures have an enhanced coercivity (Hc = 1049 Oe) higher than that of bulk Fe. The large shape anisotropy of MWCNTs, which act on the encapsulated material (Fe), is attributed for the contribution of the higher coercivity. Coiled carbon nanotubes (CCNTs) were obtained as main products in large quantities at temperature 1100 degrees C.

Estudo físico-químico de copoliéteres por viscosimetria

A viscosimetria é um procedimento experimental simples e pouco oneroso, que pode fornecer informações valiosas sobre o volume hidrodinâmico e a conformação de macromoléculas em solução, num determinado solvente, em uma dada temperatura. Os parâmetros viscosimétricos podem ser matematicamente calculados por extrapolação gráfica, cuja execução experimental é mais demorada. Em contrapartida, é possível que a determinação seja feita por um único ponto. Neste trabalho, os dois métodos de cálculo, empregando uma série de seis equações: Huggins, Kraemer e Schulz-Blaschke, por extrapolação gráfica, e Schulz-Blaschke, Solomon-Ciuta e Deb-Chanterjee por um único ponto, foram utilizados em soluções de poli(glicol propilênico) (PPG) e copolímeros em bloco à base de poli(glicol propilênico) e poli(glicol etilênico) (EG-b-PG), com diferentes teores de poli(glicol etilênico), tendo isopropanol, tetra-hidrofurano (THF) e tolueno como solventes puros, além das misturas em proporções iguais de THF/ isopropanol e THF/ tolueno, a 25C. Os valores de viscosidade intrínseca e de algumas constantes indicaram que os solventes puros e as misturas se apresentaram no limite entre o bom e o mau solvente. Verificou-se também que o método de cálculo por um único ponto foi válido, especialmente quando a equação de Schulz-Blaschke foi empregada, apresentando um baixo percentual de erro sendo possível assim reduzir o tempo de análise para a maioria dos sistemas estudados

Copolímeros à base de estireno e anidrido maleico: caracterização e estudo viscosimétrico

Copolímeros à base de estireno e anidrido maleico (SMA) são materiais sintéticos comercialmente disponíveis, obtidos pela reação dos dois monômeros citados em diferentes proporções, resultando em materiais versáteis, e disponíveis em diferentes graus de massas e porcentagens molares de anidrido maleico. São considerados polímeros funcionais devido à reatividade do grupamento anidrido maleico presente na cadeia polimérica. Por este motivo, esses materiais possuem vasta gama de aplicações, e elevada importância em diversas áreas, principalmente por terem baixa toxicidade, boa resistência térmica e boa estabilidade dimensional. Dessa forma, para melhor aplicação desses copolímeros, é muito importante o conhecimento dos parâmetros relativos ao seu comportamento em solução. A viscosimetria, em especial, é um método simples, útil e apropriado para fornecer essas informações. Os parâmetros viscosimétricos podem ser matematicamente calculados por extrapolação gráfica, entretanto a geração dos dados experimentais é mais demorada. Em contrapartida, é possível que a determinação experimental seja feita de forma mais rápida, por um único ponto, procedimento esse que desperta tanto o interesse acadêmico quanto o industrial. Neste trabalho, foram empregados os dois métodos de cálculo, utilizando solventes puros, misturas de solventes e três amostras de copolímeros à base de SMA. As determinações foram conduzidas a 40C. Os copolímeros utilizados possuiam teores de anidrido maleico de 50%, 45% e 40%, sendo os dois últimos esterificados com butil-metil-éster e sec-butil-metil-éster, respectivamente. Os solventes utilizados foram: N-metil-pirrolidona (NMP), tetrahidrofurano (THF) e suas respectivas misturas 1:1 com metil-etil-cetona (MEK), ou seja, (NMP:MEK) e THF:MEK, sendo a MEK um não solvente para o copolímero não esterificado. As equações utilizadas para extrapolação gráfica foram as de Huggins, Kraemer e Schulz-Blaschke. As equações empregadas em um único ponto foram as de Solomon-Ciuta, Deb-Chanterjee e novamente Schulz-Blaschke. Os resultados obtidos foram comparados e avaliou-se a possibilidade da utilização do método mais rápido, por um único ponto, para os sistemas estudados através dos desvios percentuais tendo como padrão os resultados da equação de Huggins. A equação de Deb-Chanterjee foi a mais adequada aos sistemas em NMP, que foi também o melhor solvente para as amostras. Os resultados obtidos na mistura NMP:MEK sugeriram que a viscosimetria pode ter sido um método sensível às pequenas diferenças estruturais entre os grupos pendentes nas amostras esterificadas. Paralelamente, realizou-se análises de espectroscopia na região do infravermelho (FTIR), análise termogravimétrica (TGA) e ensaios dinâmico-mecânicos (DMA) para a caracterização estrutural e térmica das amostras. Somente os resultados obtidos a partir de DMA indicaram diferenças entre as amostras esterificadas

Study on the kinetics of hydrate formation in a bubble column

Gas hydrate formation experiments were performed using methane in the presence of tetrahydrofuran (THF) in aqueous solution in a transparent bubble column in which a single pipe or a sintered plate was used to produce bubbles. The mole fraction of THF in aqueous solution was fixed at 6%. The hydrate formation kinetic behaviors on the surface of the rising bubble, the mechanical stability of hydrate shell formed on the surface of the bubble, the interactions among the bubbles with hydrate shell were observed and investigated morphologically. The rise velocities of individual bubbles with hydrate shells of different thickness and the consumption rates of methane gas were measured. A kinetic model was developed to correlate the experimentally measured gas consumption rate data. It was found that the hydrate formation rate on the surface of the moving bubble was high, but the formed hydrate shell was not very easy to be broken up. The bubbles with hydrate shells tended to agglomerate rather than merge into bigger bubble. This kind of characteristic of hydrate shell hindered the further formation of hydrate and led to the lower consumption rate of methane. The consumption rate of methane was found to increase with the decrease of temperature or increase of pressure. The increase of gas flux led to a linear increase in consumption rate of methane. It was demonstrated that the developed kinetic model could be used to correlate the consumption rate satisfyingly.