Oxidation of chalcopyrite by Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans in shake flasks

Chalcopyrite oxidation was evaluated with two acidophilic thiobacilli that are important in bioleaching processes. Acidithiobacillus thiooxidans in pure culture did not oxidize CuFeS2 but oxidized externally added S in the presence of CuFeS2. Acidithiobacillus ferrooxidans released Cu2+ and soluble Fe from chalcopyrite, and the time course lead to a gradual passivation of chalcopyrite whereby Cu2+ dissolution leveled off. Fe3+ acted as a chemical oxidant in CuFeS2 leaching and was reduced to Fe2+. Parallel bacterial re-oxidation of Fe2+ contributed to a high Fe3+/Fe2+ ratio and an increase in redox potential. Chemical oxidation of chalcopyrite was slow compared with A. ferrooxidans-initiated solubilization. X-ray analysis revealed new solid phases: (i) jarosite, found in solids from A. ferrooxidans cultures and in chemical controls that initially received Fe2+ or Fe3+, and (ii) S-0, found mostly in iron-amended A. ferrooxidans culture and the corresponding chemical controls. (C) 2002 Elsevier B.V. Ltd. All rights reserved.

Oxidation rate of thiosulfate and elemental sulfur in the Black Sea

Oxidation rate of 35S-thiosulfate under simulated natural conditions and abundance of thiosulfate-oxidizing bacteria in a redox zone of the Black Sea are lower during winter and spring than in summer, especially in halistatic regions. Oxidation of thiosulfate under natural conditions is performed chiefly by lithotropic thionic bacteria, whose activity is limited by low temperatures. Adding thiosulfate and readily available organic matter to water samples from the redox zone and raising temperature of water stimulated activity of heterotrophic thiosulfate-oxidizing bacteria. Oxidation of elemental sulfur tagged with 35S apparently invovled two stages: abiotic oxidation of thiosulfate and subsequent bacterial oxidation of thiosulfate to sulfate.

Tolerance to copper and zinc of Acidithiobacillus thiooxidans isolated from sewage sludge

The effect of copper and zinc ions on sulphur oxidation by Acidithiobacillus thiooxidans, strain SFR01, isolated from anaerobic sewage sludge was assessed, resulting in tolerance levels up to 20 and 200 mmol l(-1) for copper and zinc, respectively. The tolerance levels obtained were higher than the concentration of copper and zinc usually found in the collected sewage sludge. The tolerance levels obtained indicate no constraints for sludge bioleaching of those metals due to their toxicities to the indigenous A. thiooxidans.

Hydrogen sulphide removal from air by biotrickling filter using open-pore polyurethane foam as a carrier

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Role of Thiobacillus ferrooxidans and sulphur (sulphide)-dependent ferric-ion-reducing activity in the oxidation of sulphide minerals

Thiobacillus ferrooxidans oxidized the sulphide minerals e.g., pyrite, pyrrhotite and copper concentrate under anaerobic conditions in the presence of ferric ion as sole electron acceptor. Copper and iron were solubilized from sulphide ores by the sulphur (sulphide)-dependent ferric-ion oxidoreductase activity. Treatment of resting cells of T. ferrooxidans with 0.5% phenol for 30 min completely destroyed the iron- and copper-solubilizing activity. The above treatment destroyed the sulphur(sulphide)-dependent ferric-ion-reducing activity completely but did not affect the iron-oxidizing activity. The results suggest that sulphur(sulphide)-dependent ferric-ion-reducing activity actively participates in the oxidation of sulphide minerals under anaerobic conditions. The activity of sulphur(sulphide)-dependent ferric ion reduction in the solubilization of iron and copper from the sulphide ores were also observed under aerobic conditions in presence of sodium azide (0.1 μmol), which completely inhibits the iron-oxidizing activity.

Determination of sulphur monochloride by oxidation with chloramine-T

A rapid method is described for the determination of sulphur monochloride by adding excess of chloramine-T and determining the excess iodometrically.

Oxidation of aqueous sulphur dioxide catalysed by poly-4-vinylpyridine-Cu(II) complex .2. Combined homogeneous and heterogeneous phase oxidation

Aqueous phase oxidation of sulphur dioxide at low concentrations catalysed by a PVP-Cu complex in the solid phase and dissolved Cu(II) in the liquid phase is studied in a rotating catalyst basket reactor (RCBR). The equilibrium adsorption of Cu(II) and S(VI) on PVP particles is found to be of the Langmuir-type. The diffusional effects of S(IV) species in PVP-Cu resin are found to be insignificant whereas that of product S(VI) are found to be significant. The intraparticle diffusivity of S(VI) is obtained from independent tracer experiments. In the oxidation reaction HSO3- is the reactive species. Both the S(IV) species in the solution, namely SO2(aq) and HSO3- get adsorbed onto the active PVP-Cu sites of the catalyst, but only HSO3- undergoes oxidation. A kinetic mechanism is proposed based on this feature which shows that SO2(aq) has a deactivating effect on the catalyst. A rate model is developed for the three-phase reaction system incorporating these factors along with the effect of concentration of H2SO4 on the solubility of SO2 in the dilute aqueous solutions of Cu(II). Transient oxidation experiments are conducted at different conditions of concentration of SO2 and O-2 in the gas phase and catalyst concentration, and the rate parameters are estimated from the data. The observed and calculated profiles are in very good agreement. This confirms the deactivating effect of nonreactive SO2(aq) on the heterogeneous catalysis.

Deactivation of Oxidation Catalysts by Oil-Derived Sulphur

The most common mode of deactivation suffered by catalysts fitted to two-stroke engines has traditionally been thermal degradation, or even meltdown, of the washcoat and substrate. The high temperatures experienced by these catalysts are caused by excessively high concentrations of HC and CO in the exhaust gas which are, in turn, caused by a rich AFR and the loss of neat fuel to the exhaust during the scavenging period. The effects of catalyst poisoning due to additives in the oil is often regarded as a secondary, or even negligible, deactivating mechanism in two-stroke catalysts and has therefore received little attention. However, with the introduction of direct in-cylinder fuel injection to some larger versions of this engine, the quantities of HC escaping to the exhaust can be reduced to levels similar to those found on four-stroke gasoline engines. Under these conditions, the effects of poisoning are much more significant to catalyst durability, particularly for crankcase scavenged derivatives which allow considerable quantities of oil to escape into the exhaust in a neat, or partially burned form. In this paper the effects of oil-derived sulphur on catalyst performance are examined using specialised test apparatus. The oil used throughout the study was formulated specifically for a two-stroke engine fitted with direct in-cylinder fuel injection. The sulphur content of this oil was 0.21% by mass and particular attention was paid to the role of this element in the resulting deactivation. The catalyst was also designed for two-stroke applications and contained a high palladium loading of 300g/ft3 (28g/l) to prolong the life of the catalyst. It was found that the sulphur caused permanent deactivation of the CO reaction and increased the light-off temperature by around 40oC after oiling for 60 hours. This deactivation was progressive and led to a reduction in surface area of the washcoat, particularly in the micropores of around 5Å diameter. By using a validated catalyst model the change in surface area of the precious metal was estimated. It was found that the simulated palladium surface area had to be reduced by a factor of around 7.5 to produce the light-off temperature of the deactivated catalyst. Conversely, the light-off temperature of the C3H6 reaction was barely affected by the deactivation.

Investigations on the preparation, oxidation and reduction reactions of thiophosphoryl fluoride

Pure thiophosphoryl fluoride has been prepared by the fluorination of thiophosphoryl chloride by sodium fluoride in acetonitrile medium. Oxidation of this phosphoryl fluoride by acidified chloramine-T ruptures the phosphorus-sulphur bond and oxidises the sulphur present to the hexavalent state. Anhydrous hydrogen iodide reduces the sulphur to hydrogen sulphide and phosphorus to the trivalent state.

Oxidation of polythionates with chloramine-T

Chloramine-T has been found to bring about the rupture of S-S link in polythionates in acid medium and oxidise all the sulphur present in the chain into sulphuric acid. Quantitative estimation of a polythionate may be made on the basis of this oxidation reaction.

Thermodynamics of Phosphorus and Sulphur Removal during Basic Oxygen Steelmaking

Removal of impurity elements from hot metal is essential in basic oxygen steelmaking. Oxidation of phosphorus from hot metal has been studied by several authors since the early days of steelmaking. Influence of different parameters on the distribution of phosphorus, seen during the recent work of the authors, differs somewhat from that reported earlier. On the other hand, removal of sulphur during steelmaking has drawn much less attention. This may be due to the magnitude of desulphurisation in oxygen steelmaking being relatively low and desulphurisation during hot metal pre-treatment or in the ladle furnace offering better commercial viability Further, it is normally accepted that sulphur is removed to steelmaking slag in the form of sulphide only However, recent investigations have indicated that a significant amount of sulphur removed during basic oxygen steelmaking can exist in the form of sulphate in the slag under oxidising conditions. The distribution of sulphur during steelmaking becomes more important in the event of carry-over of sulphur-rich blast-furnace slag, which increases sulphur load in the BOF. The chemical nature of sulphur in this slag undergoes a gradual transition from sulphide to sulphate as the oxidative refining progresses.

Sulphur potential measurements with a two phase sulphide oxide electrolyte

The open circuit potentials of the galvanic cell,Pt (or Au)¦(Ar + H2S + H2)primeparCaS + ZrO2(CaO)par (Ar + H2S+ H2)Prime£t (or Au) has been measured in the temperature range 1000 to 1660 K and PH2S:PH 2 ratios from 1.73×10–5 to 2.65×10–1. The solid electrolyte consists of a dispersion of calcium sulphide in a matrix of calcia-stabilized zirconia. The surface of the electrolyte is coated with a thin layer of calcium sulphide to prevent the formation of water vapour by reaction of hydrogen sulphide with calcium oxide or zirconia present in the electrolyte. The use of a lsquopoint electrodersquo with a catalytically active tip was necessary to obtain steady emfs. At low temperatures and high sulphur potentials the emfs agreed with the Nernst equation. Deviations were observed at high temperatures and low sulphur potentials, probably due to the onset of significant electronic conduction in the oxide matrix of the electrolyte. The values of oxygen and sulphur potentials at which the electronic conductivity is equal to ionic conductivity in the two-phase electrolyte have been evaluated from the emf response of the cell. The sulphide-oxide electrolyte is unsuitable for sulphur potential measurements in atmospheres with high oxygen potentials, where oxidation of calcium sulphide may be expected.

An investigation of the thermal stability and sulphur tolerance of Ag/Y-Al2O3 catalysts for the SCR of NOx with hydrocarbons and hydrogen

The sulphur tolerance and thermal stability of a 2 wt% Ag/gamma-Al2O3 catalyst was investigated for the H-2-promoted SCR of NO, with octane and toluene. The aged catalyst was characterised by XRD and EXAFS analysis. It was found that the effect of ageing was a function of the gas mix and temperature of ageing. At high temperatures (800 degrees C) the catalyst deactivated regardless of the reaction mix. EXAFS analysis showed that this was associated with the Ag particles on the surface of the catalyst becoming more ordered. At 600 and 700 degrees C, the deactivating effect of ageing was much less pronounced for the catalyst in the H-2-promoted octane-SCR reaction and ageing at 600 degrees C resulted in an enhancement in activity for the reaction in the absence of H-2. For the toluene + H-2-SCR reaction the catalyst deactivated at each ageing temperature. The effect of addition of low levels of sulphur (1 ppm SO2) to the feed was very much dependent on the reaction temperature. There was little deactivation of the catalyst at low temperatures ( 500 degrees C). The results can be explained by the activity of the catalyst for the oxidation Of SO2 to SO3 and the relative stability of silver and aluminium sulphates. The catalyst could be almost fully regenerated by a combination of heating and the presence of hydrogen in the regeneration mix. The catalyst could not be regenerated in the absence of hydrogen. (c) 2006 Published by Elsevier B.V.