Eutectic nucleation and growth in hypoeutectic Al-SI alloys at different strontium levels

The effects of different levels of strontium on nucleation and growth of the eutectic in a commercial hypoeutectic Al-Si foundry alloy have been investigated by optical microscopy and electron backscattering diffraction (EBSD) mapping by scanning electron microscopy (SEM). The microstructural evolution of each specimen during solidification was studied by a quenching technique at different temperatures and Sr contents. By comparing the orientation of the aluminum in the eutectic to that of the surrounding primary aluminum dendrites by EBSD, the eutectic formation mechanism could be determined. The results of these studies show that the eutectic nucleation mode, and subsequent growth mode, is strongly dependent on Sr level. Three distinctly different eutectic growth modes were found, in isolation or sometimes together, but different for each Sr content. At very low Sr contents, the eutectic nucleated and grew from the primary phase. Increasing the Sr level to between 70 and 110 ppm resulted in nucleation of independent eutectic grains with no relation to the primary dendrites. At a Sr level of 500 ppm, the eutectic again nucleated on and grew from the primary phase while a well-modified eutectic structure was still present. A slight dependency of eutectic growth radially from the mold wall opposite the thermal gradient was observed in all specimens in the early stages of eutectic solidification.

Ionic strontium fluorescence as a method for flow tagging velocimetry

A flow tagging technique based upon ionic fluorescence in strontium is investigated for applications to velocity measurements in gas flows. The method is based upon a combination of two laser based spectroscopic techniques, i.e. resonantly-enhanced ionisation and laser-induced ionic fluorescence. Strontium is first ionised and then planar laser-induced fluorescence is utilised to give 2D 'bright images' of the ionised region of the flow at a given time delay. The results show that this method can be used for velocity measurements. The velocities were measured in two types of air-acetylene flames - a slot burner and a circular burner yielding velocities of 5.1 +/- 0.1 m/s and 9.3 +/- 0.2 m/s, respectively. The feasibility of the method for the determination of velocities in faster flows than those investigated here is discussed.

Eutectic growth mode in strontium, antimony and phosphorus modified hypoeutectic Al-Si foundry alloys

The effect of strontium (Sr), antimony (Sb) and phosphorus (P) on nucleation and growth mode of the eutectic in hypoeutectic Al-10 mass%Si alloys has been investigated by electron back-scattering diffraction (EBSD) mapping. Specimens were prepared from a hypoeutectic Al-10 mass%Si base alloy, adding different levels of strontium, antimony and phosphorus for modification of eutectic silicon. By comparing the orientation of the aluminium in the eutectic to that of the surrounding primary aluminium dendrites, the solidification mode of the eutectic could be determined. The results of these studies show that the eutectic nucleation mode, and subsequent growth mode, is strongly dependent on additive elements. The EBSD mapping results indicate that the eutectic grew from the primary phase in unmodified and phosphorus-containing alloys. When the eutectic was modified by strontium or antimony, eutectic grains nucleated and grew separately from the primary dendrites.

Fabrication and characterisation of ferroelectric lead zirconate titanate and strontium bismuth tantalate thin films

Ferroelectrics, liquid delivery, MOCVD, lead zirconate titanate, strontium bismuth tantalate

Sulfur and strontium isotope composition of the Llobregat River (NE Spain): Tracers of natural and anthropogenic chemicals in stream waters

The use of sulfur and strontium isotopes as tracers for the source/s of water contaminants have been applied to the water of the Llobregat River system (NE Spain). Surface water samples from June 1997 were collected from the Llobregat River and its main tributaries and creeks. The chemistry of most stream waters are controlled mainly by the weathering of Tertiary chemical sediments within the drainage basin. The largest variation in delta(34)S values were found in the small creeks with values ranging from -9.9 to 15parts per thousand, whilst in the main river channels values ranged from 6.3 to 12.4parts per thousand. The Sr-87/Sr-86 ratio for dissolved strontium ranged from 0.70795 for a non-polluted site to 0.70882 for a polluted one. Most of the waters with high NO3 and low Ca/Na ratio converge to the same Sr-87/Sr-86 value, pointing to dominant pollutant end member contribution or a mixing of pollutants with an isotopic composition around 0.7083-0.7085. Although the concentration of the natural inputs in the river for sulfate and strontium are high, as a result of the sulfate outcrops within the geology of the basin, their isotopic characteristics suggest that they can be used as a discriminating device in water pollution problems. However to establish the detailed characteristics of the isotopes as geochemical tools, specific high-resolution case studies are necessary in small areas, where the inputs are well known.

Beneficial effects of strontium ranelate compared to alendronate on bone micro-structure - a 2-year study

Aims: In a head-to-head study, we compared the effects of strontium ranelate (SrRan) and alendronate (ALN), anti-osteoporotic agents with antifracture efficacy, on bone microstructure, a component of bone quality, hence of bone strength. Methods: In a randomised, double-dummy, double-blind controlled trial, 88 postmenopausal osteoporotic women were randomised to SrRan 2g/day or ALN 70mg/week for 2 years. Microstructure of the distal radius and distal tibia were assessed by HR-pQCT after 3,6,12,18 and 24 months of treatment. Primary endpoint was HR-pQCT variables relative changes from baseline. An ITT analysis was applied. Results: Baseline characteristics were similar in both groups (mean ±SD): age: 63.6±7.5 vs. 63.7±7.6 yrs; L1-L4T Score: -2.7±0.8 vs. -2.8±0.8g/cm², Cortical Thickness (CTh), trabecular bone fraction (BV/TV) and cortical density=721±242 vs. 753±263μm, 9.5±2.5 vs. 9.3±2.7%, and 750±87 vs. 745±78mg/cm3 respectively. Over 2 yrs, distal radius values changes were within 1 to 2% without significant differences except cortical density. In contrast distal tibia CTh, BV/TV, trabecular and cortical densities increased significantly more in the SrRan group than in the ALN group (Table). No significant between-group differences were observed for the remaining measured parameter (trabecular number, trabecular spacing, and trabecular thickness). After 2 years, L1- L4 and hip aBMD increases were similar to results from pivotal trials (L1-L4:+6.5% and +5.6%;total hip:+4.1% and +2.9%, in Sr- Ran and ALN groups, respectively). In the SrRan group, bALP increased by a median of 18% (p<0.001) and sCTX decreased by a median of -16% (p=0.005) while in the ALN group, bALP and CTX decreased by median of -31% (p<0.001) and -59% (p<0.001) respectively. Relative changes from baseline to last observation (%) SrRan ALN Estimated between group difference p value CTh (μm) 6.29±9.53 0.93±6.23 5.411±1.836 0.004 BV/TV (%) 2.48±5.13 0.84±3.81 1.783±0.852 0.040 Trabecular density (mgHA/cm3) 2.47±5.07 0.88±4.00 1.729±0.859 0.048 Cortical density (mgHA/cm3) 1.43±2.77 0.36±2.14 1.137±0.530 0.045 The two treatments were well tolerated. Conclusions: Within the constraints related to HRpQCT technology, it appears that strontium ranelate has greater effects than alendronate on distal tibia cortical thickness, trabecular and cortical bone densities in women with postmenopausal osteoporosis after two years of treatment. A concomitant significant increase in bone formation marker is observed in the SrRan group.

Strontium ranelate and alendronate have differing effects on distal tibia bone microstructure in women with osteoporosis.

The structural basis of the antifracture efficacy of strontium ranelate and alendronate is incompletely understood. We compared the effects of strontium ranelate and alendronate on distal tibia microstructure over 2 years using HR-pQCT. In this pre-planned, interim, intention-to-treat analysis at 12 months, 88 osteoporotic postmenopausal women (mean age 63.7 +/- 7.4) were randomized to strontium ranelate 2 g/day or alendronate 70 mg/week in a double-placebo design. Primary endpoints were changes in microstructure. Secondary endpoints included lumbar and hip areal bone mineral density (aBMD), and bone turnover markers. This trial is registered with http://www.controlled-trials.com, number ISRCTN82719233. Baseline characteristics of the two groups were similar. Treatment with strontium ranelate was associated with increases in mean cortical thickness (CTh, 5.3%), cortical area (4.9%) and trabecular density (2.1%) (all P < 0.001, except cortical area P = 0.013). No significant changes were observed with alendronate. Between-group differences in favor of strontium ranelate were observed for CTh, cortical area, BV/TV and trabecular density (P = 0.045, 0.041, 0.048 and 0.035, respectively). aBMD increased to a similar extent with strontium ranelate and alendronate at the spine (5.7% versus 5.1%, respectively) and total hip (3.3% versus 2.2%, respectively). No significant changes were observed in remodeling markers with strontium ranelate, while suppression was observed with alendronate. Within the methodological constraints of HR-pQCT through its possible sensitivity to X-ray attenuation of different minerals, strontium ranelate had greater effects than alendronate on distal tibia cortical thickness and trabecular volumetric density.

Effets bénéfiques du ranélate de strontium compare à l'alendronate sur le TBS chez les femmes ostéoporotiques ménopausées: une étude de 2 ans.

Introduction. - Le TBS ou Score Trabéculaire Osseux (TBS, Med- Imaps, France) est un index d'architecture osseuse apportant des informations indépendantes de la densité minérale osseuse (DMO), et calculé par la quantification des variations locales des niveaux de gris à partir d'examen de densitométrie (DXA) lombaire. Dans des études antérieures prospectives et cas-témoins, cet index a été considéré comme associé aux fractures. Nous avons comparé les effets du ranélate de strontium (RanSr) et de l'alendronate (ALN) sur l'architecture vertébrale à l'aide du TBS, chez des femmes ostéoporotiques ménopausées. Patients et méthodes. - Une analyse post hoc a été réalisée sur des DXA (Hologic and GE Lunar Devices) de 79 des 189 femmes incluses dans une étude en double aveugle et double placebo et réparties de façon randomisée entre un groupe à 2 g/jour de RanSr et un groupe à 70 mg/semaine d'ALN pendant 2 ans. Les paramètres de TBS ont été évalués en aveugle par TBS iNsight (v1,9) au niveau vertébral après 12 et 24 mois de traitement. Nous avons appliqué les règles de l'ISCD (International Society for Clinical Densitometry) pour chaque exclusion de vertèbre, de façon indépendante respectivement pour la DMO et le TBS. Des doubles mesures ayant été réalisées initialement, la reproductibilité est exprimée en % CV. Résultats. - Les caractéristiques initiales (moyenne ± DS) étaient identiques entre les groupes en termes d'âge, 69,2 ± 4,4 ans ; d'IMC, 23,8 ± 4,4 kg/m2 ; de T-score L1-L4, - 2,9 ± 0,9 et de TBS, 1,230 ± 0,09. Comme prévu, le coefficient de détermination entre la DMO et le TBS au niveau du rachis était très basse r2 = 0,12. Les reproductibilités brutes étaient respectivement de 1,1 et 1,6 % pour la DMO et le TBS au niveau vertébral. Après 1 et 2 ans, la DMO en L1-L4 a augmenté de façon significative de respectivement 5,6 % et 9 % dans le groupe RanSr et de respectivement 5,2 % et 7,6 % dans le groupe ALN. De même, le TBS au niveau vertébral a augmenté respectivement de 2,3 % (p < 0,001) et de 3,1 % (p < 0,001) dans le groupe RanSr et de 0,5 % (NS) et de 1 % (NS) dans le groupe ALN avec une différence entre groupe significative en faveur du RanSr (p = 0,04 et p = 0,03). Il n'y avait aucune corrélation entre la différence de DMO et de TBS à 1 ou 2 ans. Les deux traitements étaient bien tolérés. Discussion. - Ces résultats sur le TBS confortent des études précédentes qui sont en faveur de l'effet bénéfique du RanSr sur l'architecture osseuse. Conclusion. - Le ranélate de strontium a des effets plus importants que l'alendronate sur le score trabéculaire osseux, indice d'architecture osseuse au niveau vertébral, chez les femmes ayant une ostéoporose post-ménopausique, après 2 ans de traitement.

Effects of strontium ranelate and alendronate on bone microstructure in women with osteoporosis. Results of a 2-year study.

A Strontium ranelate appears to influence more than alendronate distal tibia bone microstructure as assessed by high-resolution peripheral quantitative computed tomography (HR-pQCT), and biomechanically relevant parameters as assessed by micro-finite element analysis (mu FEA), over 2 years, in postmenopausal osteoporotic women.Introduction Bone microstructure changes are a target in osteoporosis treatment to increase bone strength and reduce fracture risk.Methods Using HR-pQCT, we investigated the effects on distal tibia and radius microstructure of strontium ranelate (SrRan; 2 g/day) or alendronate (70 mg/week) for 2 years in postmenopausal osteoporotic women. This exploratory randomized, double-blind trial evaluated HR-pQCT and FEA parameters, areal bone mineral density (BMD), and bone turnover markers.Results In the intention-to-treat population (n = 83, age: 64 +/- 8 years; lumbar T-score: -2.8 +/- 0.8 [DXA]), distal tibia Cortical Thickness (CTh) and Density (DCort), and cancellous BV/TV increased by 6.3%, 1.4%, and 2.5%, respectively (all P < 0.005), with SrRan, but not with alendronate (0.9%, 0.4%, and 0.8%, NS) (P < 0.05 for all above between-group differences). Difference for CTh evaluated with a distance transformation method was close to significance (P = 0.06). The estimated failure load increased with SrRan (+2.1%, P < 0.005), not with alendronate (-0.6%, NS) (between-group difference, P < 0.01). Cortical stress was lower with SrRan (P < 0.05); both treatments decreased trabecular stress. At distal radius, there was no between-group difference other than DCort (P < 0.05). Bone turnover markers decreased with alendronate; bALP increased (+21%) and serum-CTX-I decreased (-1%) after 2 years of SrRan (between-group difference at each time point for both markers, P < 0.0001). Both treatments were well tolerated.Conclusions Within the constraints of HR-pQCT method, and while a possible artefactual contribution of strontium cannot be quantified, SrRan appeared to influence distal tibia bone microstructure and FEA-determined biomechanical parameters more than alendronate. However, the magnitude of the differences is unclear and requires confirmation with another method.

Surface effect ferromagnetism in pure and reduced strontium titanate

A room temperature ferromagnetic hysteresis is observed in single crystal strontium titanate substrates as purchased from several manufacturers. It was found that polishing all sides of the substrates removed this observed hysteresis, suggesting that the origin of the ferromagnetic behavior resides on the surface of the substrates. X-ray diffraction and energy dispersive x-ray spectra were measured however they were unable to detect any impurity phases. In similar semiconducting oxides it was previously suggested that ferromagnetism could originate in oxygen vacancies or from disorder within the single crystal. To this end substrates were annealed in both air and vacuum in a range of temperatures (600°C to 1100°G) to both create bulk oxygen vacancies and to heal surface damage. Annealing in vacuum was found to create a measureable number of oxygen vacancies however their creation could not be correlated to the ferromagnetic signal of the substrate. Annealing in air was found to effect the remnant moment of the substrate as well as the width of the x-ray diffraction peaks on the unpolished face, weakly suggesting a relation between surface based disorder and ferromagnetism. Argon ion bombardment was employed to create a layer of surface disorder in the polished crystal, however it was not found to induce ferromagnetism. It was found that acid etching was sufficient to remove the ferromagnetism from as purchased samples and similarly simulated handling with stainless steel tweezers was sufficient to re-create the ferromagnetism. It is suggested that the origin of this ferromagnetism in SrTi03 is surface contaminants (mainly iron).

Essai de détection de processus migratoires à travers les isotopes de strontium et d’oxygène : étude des restes humains du cimetière Saint-Matthew (Québec, 1771-1860)

Afin de distinguer les immigrants de première génération des individus nés à Québec et de discuter de l’identité des immigrants de cette ville aux XVIIIe et XIXe siècles, trente-quatre squelettes humains exhumés du cimetière protestant Saint-Matthew (Québec, 1771-1860) ont fait l’objet d’analyses ostéologiques et isotopiques du strontium (87Sr/86Sr) et de l’oxygène (δ18O). Les teneurs obtenues, bien que moins précises que les données historiques, ont permis de distinguer trois groupes d’origine, soit les individus nés à Québec (N = 12), les immigrants de première génération provenant le plus probablement des îles Britanniques et du nord de la France (N = 19) et les immigrants de première génération dont l’origine ne peut être précisée (N = 3). De plus, l’origine écossaise de certains individus a pu être suggérée en fonction de compositions isotopiques variant entre -10,0 et -9,09 % vs VSMOW. La comparaison des groupes d’origine à des données provenant de sources historiques et d’une étude antérieure a permis de dresser un portrait de l’identité des immigrants, à la fois sur les plans populationnel et individuel. De plus, les compositions isotopiques (δ18O, 87Sr/86Sr, δ13C et δ15N) nous laissent croire qu’au moins un individu pourrait être d’origine amérindienne et qu’un autre proviendrait d’une partie de l’Europe plus appauvrie en 18O (possiblement un pays scandinave ou une région alpine). La distribution spatiale des sépultures nous a également permis d’émettre des hypothèses sur les liens familiaux et sociaux d’immigrants inhumés en caveaux ou entassés de façon particulièrement modeste.

Luminescence studies of strontium sulphide based phosphors for display applications

This thesis has focused on the synthesis and analysis of some important phosphors (nano, bulk and thin film) for display applications. ACTFEL device with SrS:Cu as active layer was also fabricated.Three bulk phosphors: SrS:Cu,CI; SrS:Dy,Cl; and SrS:Dy,Cu,Cl were synthesized and their structural, optical and electrical properties were investigated. Special emphasis was given to, the analysis of the role of defects and charge compensating centers, on the structural changes of the host and hence the luminance. A new model describing the sensitizing behaviour of Cu in SrS:Dy,Cu,Cl two component phosphor was introduced. It was also found that addition of NH4CI as flux in SrS:Cu caused tremendous improvement in the structural and luminescence properties.A novel technique for ACTFEL phosphor deposition at low temperature was introduced. Polycrystalline films of SrS:Cu,F were synthesized at low temperature by concomitant evaporation of host and dopant by electron beam evaporation and thermal evaporatin methods.Copper doped strontium sulphide nanophosphor was synthesized for the first time. Improvement in the luminescence properties was observed in the nanophosphor with respect to it' s bulk counterpart.