Estimating the diameter of yarns with irregular constituent fibres

Yarn diameter and packing density are difficult to measure directly. Existing models on fibre packing density in a yarn assume that all fibres are uniform and have an identical diameter. Yet real staple yarns, such as wool yarns, consist of fibres of varying diameters. This paper proposes an effective and simple yarn model for calculating the average diameter of yarns, in which fibres have circular cross-section and the close packing in the yarn cross-section. The concept of “area equivalent diameter” is introduced to transform fibres of varying diameters to identical fibres with one equivalent diameter to simplify the calculations of the average yarn diameter for a range of yarns.

Minimizing energy consumption of yarn winding in ring spinning

Ring spinning has been and will continue to be an important system for making staple yarns from different fibers in the textile industry. But high power consumption and low productivity remain the two outstanding problems with ring spinning. Based on an analysis of power distribution during yarn winding in ring spinning, models for the ratio of energy consumption to yarn production over a full yarn package are established. Spindle speed, yarn count, and package diameter are the three key parameters affecting this ratio. The effects on energy consumption of these parameters are discussed through a case study. The energy-to-production ratio increases with increased package diameter but decreases with increased spindle speed and/or yarn count (tex). The results will help guide spinners in minimizing energy consumption in ring spinning.

Embeddable and locatable spinning

A novel spinning method: embeddable and locatable spinning, is reported for the first time in this paper. Analysis of the key restrictions of the conventional and some novel ring-spinning were studied; evolvement and principles of embeddable and locatable spinning were then introduced. Analysis indicated that embeddable and locatable spinning could overcome the existing restrictions of ring spinning and improve the spinning performance of fiber strands as well as the quality of the resulting yarn. Super-fine and colorful figured yarns could be produced successfully, and most fibers shorter than can be spun in traditional spinning could be well embedded into a yarn by embeddable and locatable spinning method; even staple fibers of low qualities could be used to produce a fine yarn of high qualities in the novel spinning system. This novel spinning method shows huge application potentials in textile industry by improving the yarn quality, developing super-fine yarn, and increasing fiber utilization rate.

Twist distribution in staple fibre yarns

Staple fibre yarns vary quite markedly in linear density (tex) along their length and the degree to which twist redistributes from thick to thin places will affect the strength, torque and extension behaviour of the yarn. Theory suggests that twist along worsted yarns should vary as 1/(tex)2 if fibres were locked in the structure, whereas themean torque of worsted yarns reported in the literature implies that twist should be proportional to 1/tex. This article examines twist distribution in ring-spun marl yarns, down to 5 mm resolution, as a function of linear density measured using a high-resolution capacitive sensor. It is found for moderate twist-level worsted yarns that twist is approximately proportional to 1/(tex)1.6. The results and theory provide a guide as to the effect the observed large variations in linear density will have on yarn properties such as tenacity and torque.

Solospun : the long staple weavable singles yarn

Solospun^TM is a spinning technology which provides the means to produce a singles yarn that can be successfully woven as either warp or weft. The technology is a versatile and cost effective alternative to two-folding, Sirospun or sizing. It offers significant benefits in terms of efficiency and productivity. Solospun^TM is a simple, inexpensive, clip-on attachment for the spinning of long staple, weavable singles yarns. The technology is the result of a joint development between CSIRO Textile and Fibre Technology, The Woolmark Company and WRONZ and was commercially released in 1998. It is now successfully operating in worsted mills worldwide. The Solospun^TM hardware consists of a pair of rollers held in a bracket, which is clipped onto the front of the pendulum-drafting arm. Each roller is positioned immediately below, and parallel to, each top front draft roller where it interacts with the emerging drafted fibre strand before twist insertion. The roller-fibre interaction subtly changes the structure of the yarn, which dramatically increases its abrasion resistance. This allows Solospun yarns to be woven without twofolding or sizing, providing significant cost savings. Depending on fabric structure, weaving performance is equivalent to that of conventional two-fold yarns. Fabrics woven from Solospun^TM yarns are of good quality and appearance. Some aspects, including preferred hand and FAST results, are equal or superior to two-fold yarn fabrics. As with compact and condensed spinning, Solospun^TM offers significant reductions in yarn
hairiness. However, Solospun can be simply implemented on existing spinning frames and goes much further by making the singles yarns weavable.

In-situ tensile properties of a ballooning staple yarn

This study investigated the tensile properties of a rotating or ballooning staple yarn. The results indicated that the effect of rotating speed on the tensile properties of a ballooning staple yarn was significant. As the yarn rotating speed increased, the tenacity of the rotating or ballooning yarn decreased, while the yarn breaking elongation increased. The effect of rotating speed on the tenacity of a ballooning staple yarn varied for different yarns. These results demonstrated that the breaking force of a ballooning yarn was much lower than the yarn breaking force obtained from normal tensile tests. These results provide new insight into the problems of yarn breakage in yarn spinning and twisting processes.

Weaving yarns : the lived experience of Indigenous Australians with adult-onset disability in Brisbane

Indigenous Australians have lower levels of health than mainstream Australians and (as far as statistics are able to indicate) higher levels of disability, yet there is little information on Indigenous social and cultural constructions of disability or the Indigenous experience of disability. This research seeks to address these gaps by using an ethnographic approach, couched within a critical medical anthropology (CMA) framework and using the “three bodies” approach, to study the lived experience of urban Indigenous people with an adult-onset disability. The research approach takes account of the debate about the legitimacy of research into Indigenous Australians, Foucault‟s governmentality, and the arguments for different models of disability. The possibility of a cultural model of disability is raised. After a series of initial interviews with contacts who were primarily service providers, more detailed ethnographic research was conducted with three Indigenous women in their homes and with four groups of Indigenous women and men at an Indigenous respite centre. The research involved multiple visits over a period extending more than two years, and the establishment of relationships with all participants. An iterative inductive approach utilising constant comparison (i.e. a form of grounded theory) was adopted, enabling the generation and testing of working hypotheses. The findings point to the lack of an Indigenous construct of disability, related to the holistic construction of health among Indigenous Australians. Shame emerges as a factor which affects the way that Indigenous Australians respond to disability, and which operates in apparent contradiction to expectations of community support. Aspects of shame relate to governmentality, suggesting that self-disciplinary mechanisms have been taken up and support the more obvious exertion of government power. A key finding is the strength of Indigenous identity above and beyond other forms of identification, e.g. as a person with a disability, expressed in forms of resistance by individuals and service providers to the categories and procedures of the mainstream. The implications of a holistic construction of health are discussed in relation to the use of CMA, the interpretation of the “three bodies”, governmentality and resistance. The explanatory value of the concept of sympatricity is discussed, as is the potential value of a cultural model of disability which takes into account the cultural politics of a defiant Indigenous identity.

Allelic variation at a single gene increases food value in a drought-tolerant staple cereal

The production of adequate agricultural outputs to support the growing human population places great demands on agriculture, especially in light of ever-greater restrictions on input resources. Sorghum is a drought-adapted cereal capable of reliable production where other cereals fail, and thus represents a good candidate to address food security as agricultural inputs of water and arable land grow scarce. A long-standing issue with sorghum grain is that it has an inherently lower digestibility. Here we show that a low-frequency allele type in the starch metabolic gene, pullulanase, is associated with increased digestibility, regardless of genotypic background. We also provide evidence that the beneficial allele type is not associated with deleterious pleiotropic effects in the modern field environment. We argue that increasing the digestibility of an adapted crop is a viable way forward towards addressing food security while maximizing water and land-use efficiency.

Intervertebral staple grading system with micro-CT

Introduction Intervertebral stapling is a leading method of fusionless scoliosis treatment which attempts to control growth by applying pressure to the convex side of a scoliotic curve in accordance with the Hueter-Volkmann principle. In addition to that, staples have the potential to damage surrounding bone during insertion and subsequent loading. The aim of this study was to assess the extent of bony structural damage including epiphyseal injury as a result of intervertebral stapling using an in vitro bovine model. Materials and Methods Thoracic spines from 6-8 week old calves were dissected and divided into motion segments including levels T4-T11 (n=14). Each segment was potted in polymethylemethacrylate. An Instron Biaxial materials testing machine with a custom made jig was used for testing. The segments were tested in flexion/extension, lateral bending and axial rotation at 37⁰C and 100% humidity, using moment control to a maximum 1.75 Nm with a loading rate of 0.3 Nm per second for 10 cycles. The segments were initially tested uninstrumented with data collected from the tenth load cycle. Next an anterolateral 4-prong Shape Memory Alloy (SMA) staple (Medtronic Sofamor Danek, USA) was inserted into each segment. Biomechanical testing was repeated as before. The staples were cut in half with a diamond saw and carefully removed. Micro-CT scans were performed and sagittal, transverse and coronal reformatted images were produced using ImageJ (NIH, USA).The specimens were divided into 3 grades (0, 1 and 2) according to the number of epiphyses damaged by the staple prongs. Results: There were 9 (65%) segments with grade 1 staple insertions and 5 (35%) segments with grade 2 insertions. There were no grade 0 staples. Grade 2 spines had a higher stiffness level than grade 1 spines, in all axes of movement, by 28% (p=0.004). This was most noted in flexion/extension with an increase of 49% (p=0.042), followed by non-significant change in lateral bending 19% (p=0.129) and axial rotation 8% (p=0.456) stiffness. The cross sectional area of bone destruction from the prongs was only 0.4% larger in the grade 2 group compared to the grade 1 group (p=0.961). Conclusion Intervertebral staples cause epiphyseal damage. There is a difference in stiffness between grade 1 and grade 2 staple insertion segments in flexion/extension only. There is no difference in the cross section of bone destruction as a result of prong insertion and segment motion.

The effect of intervertebral staple insertion on bovine spine segment stiffness

Introduction There is growing interest in the biomechanics of ‘fusionless’ implant constructs used for deformity correction in the thoracic spine. Intervertebral stapling is a leading method of fusionless corrective surgery. Although used for a number of years, there is limited evidence as to the effect these staples have on the stiffness of the functional spinal unit. Materials and Methods Thoracic spines from 6-8 week old calves were dissected and divided into motion segments including levels T4-T11 (n=14). Each segment was potted in polymethylemethacrylate. An Instron Biaxial materials testing machine with a custom made jig was used for testing. The segments were tested in flexion/extension, lateral bending and axial rotation at 37⁰C and 100% humidity, using moment control to a maximum 1.75 Nm with a loading rate of 0.3 Nm per second. This torque was found sufficient to achieve physiologically representative ranges of movement. The segments were initially tested uninstrumented with data collected from the tenth load cycle. Next a left anterolateral Shape Memory Alloy (SMA) staple was inserted (Medtronic Sofamor Danek, USA). Biomechanical testing was repeated as before with data collected from the tenth load cycle. Results In flexion/extension there was an insignificant drop in stiffness of 3% (p=0.478). In lateral bending there was a significant drop in stiffness of 21% (p<0.001). This was mainly in lateral bending away from the staple, where the stiffness reduced by 30% (p<0.001). This was in contrast to lateral bending towards the staple where it dropped by 12% which was still statistically significant (p=0.036). In axial rotation there was an overall near significant drop in stiffness of 11% (p=0.076). However, this was more towards the side of the staple measuring a decrease of 14% as opposed to 8% away from the staple. In both cases it was a statistically insignificant drop (p=0.134 and p=0.352 respectively). Conclusion Insertion of intervertebral SMA staples results in a significant reduction in motion segment stiffness in lateral bending especially in the direction away from the staple. The staple had less effect on axial rotation stiffness and minimal effect on flexion/extension stiffness.

Genetic Parameters for Staple Length and Staple Strength of Merino Wool Produced in Central and North West Queensland

Estimates of genetic parameters are presented for staple length and staple strength for 15 month old, medium Peppin sheep at Longreach and Julia Creek Queensland. The effects of birth type, sex and year of birth are shown. There were significant interactions for sex by site and for sex by year of birth. Heritability of staple length and strength were respectively 0.75 and 0.37 for the Longreach flock and 0.70 and 0.23 for the Julia Creek flock. The heritability of staple strength agrees with other published data however the estimate for staple length is very high. Phenotypic and genetic correlations with greasy fleece weight, yield, clean fleece weight, average fibre diameter and liveweight are in general agreement with other published estimates. Animal production for a consuming world : proceedings of 9th Congress of the Asian-Australasian Association of Animal Production Societies [AAAP] and 23rd Biennial Conference of the Australian Society of Animal Production [ASAP] and 17th Annual Symposium of the University of Sydney, Dairy Research Foundation, [DRF]. 2-7 July 2000 University of New South Wales, Sydney, Australia.

Allelic variation at a single gene increases food value in a drought-tolerant staple cereal

The production of adequate agricultural outputs to support the growing human population places great demands on agriculture, especially in light of ever-greater restrictions on input resources. Sorghum is a drought-adapted cereal capable of reliable production where other cereals fail, and thus represents a good candidate to address food security as agricultural inputs of water and arable land grow scarce. A long-standing issue with sorghum grain is that it has an inherently lower digestibility. Here we show that a low-frequency allele type in the starch metabolic gene, pullulanase, is associated with increased digestibility, regardless of genotypic background. We also provide evidence that the beneficial allele type is not associated with deleterious pleiotropic effects in the modern field environment. We argue that increasing the digestibility of an adapted crop is a viable way forward towards addressing food security while maximizing water and land-use efficiency.

Barium-Functionalized Multiwalled Carbon Nanotube Yarns As Low-Work-Function Thermionic Cathodes

Barium-functionalized multiwalled carbon nanotube yarns were fabricated by drawing and twisting multiwalled carbon nanotube forests through a solution containing barium nitrate. After heat activation under vacuum, the functionalized yarns were enriched in barium oxide due to the high surface-to-volume ratio of the nanotubes. The cathodes exhibited good thermionic properties, with a work function as low as 1.73-2.06 eV and thermionic current density that exceeded 185 mA/cm(2) in a field of 850 V/5 mm at 1317 K. The barium-functionalized yarns had high tensile strength of up to 420 MPa and retained strength of similar to 250 MPa after a 2 h activation process. (C) 2008 American Institute of Physics.