Influence of spray mixture volume and flight height on herbicide deposition in aerial applications on pastures

The objective of the present study was to analyze the influence of spray mixture volume and flight height on herbicide deposition in aerial applications on pastures. The experimental plots were arranged in a pasture area in the district of Porto Esperidião (Mato Grosso, Brazil). In all of the treatments, the applications contained the herbicides aminopyralid and fluroxypyr (Dominum) at the dose of 2.5 L c.p. ha-1, including the adjuvant mineral oil (Joint Oil) at the dose of 1.0 L and a tracer to determine the deposition by high-performance liquid chromatography (HPLC) (rhodamine at a concentration of 0.6%). The experiment consisted of nine treatments that comprised the combinations of three spray volumes (20, 30 and 50 L ha-1) and three flight heights (10, 30 and 40 m). The results showed that, on average, there was a tendency for larger deposits for the smallest flight heights, with a significant difference between the heights of 10 and 40 m. There was no significant difference among the deposits obtained with the different spray mixture volumes.

Influence of spray mixture volume and flight height on herbicide deposition in aerial applications on pastures

The objective of the present study was to analyze the influence of spray mixture volume and flight height on herbicide deposition in aerial applications on pastures. The experimental plots were arranged in a pasture area in the district of Porto Esperidião (Mato Grosso, Brazil). In all of the treatments, the applications contained the herbicides aminopyralid and fluroxypyr (Dominum) at the dose of 2.5 L c.p. ha-1, including the adjuvant mineral oil (Joint Oil) at the dose of 1.0 L and a tracer to determine the deposition by high-performance liquid chromatography (HPLC) (rhodamine at a concentration of 0.6%). The experiment consisted of nine treatments that comprised the combinations of three spray volumes (20, 30 and 50 L ha-1) and three flight heights (10, 30 and 40 m). The results showed that, on average, there was a tendency for larger deposits for the smallest flight heights, with a significant difference between the heights of 10 and 40 m. There was no significant difference among the deposits obtained with the different spray mixture volumes.

Influência da chuva na eficácia do glyphosate em mistura com adjuvantes na dessecação de plantas daninhas

Com o objetivo de estudar a influência do momento da chuva após a aplicação do herbicida glyphosate isolado e em mistura com adjuvantes na dessecação de plantas daninhas, foram instalados dois experimentos na Fazenda Experimental de Ensino e Pesquisa da Faculdade de Ciências Agrárias e Veterinárias, UNESP - campus de Jaboticabal-SP, em duas épocas: inverno de 2000 (junho - agosto) e verão de 2001 (janeiro-março). Os experimentos foram instalados no delineamento experimental de blocos ao acaso, em arranjo fatorial 4 (tratamentos herbicidas) x 5 (períodos livres de chuva simulada) + 1, com quatro repetições. Os tratamentos consistiram da combinação de glyphosate SAqC (360 g e.a. ha-1) isolado ou adicionado de uréia (50 g L-1 de calda) ou óleo vegetal (100 ml L-1 de calda) ou sulfato de amônio (100 g L-1 de calda), com cinco períodos de chuva simulada (1, 2, 4, 6 e > 48 horas após a aplicação), além de uma testemunha. A chuva foi simulada com um sistema de irrigação por aspersão, e a quantidade aplicada variou entre 18 e 19 mm. em ambas as épocas a chuva foi prejudicial à ação do glyphosate, principalmente nos menores períodos livres de chuva após a aplicação. Os sintomas de fitointoxicação apareceram mais rapidamente no verão. A utilização de adjuvantes na calda de pulverização não beneficiou o desempenho do herbicida glyphosate no controle das plantas daninhas, no inverno. A adição de uréia (50 g L¹) é uma boa alternativa para o controle de plantas daninhas, no verão, em situações sujeitas à chuva até duas horas após a aplicação.

Depósitos de calda obtidos com a aplicação aérea de defensivos na cultura da banana

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Espectro de gotas de pontas de pulverização com adjuvantes de uso agrícola

O sucesso de uma boa aplicação de produtos fitossanitários depende da sinergia entre fatores como tamanho de gota, tipo de ponta, pressão, volume e composição da calda e características do alvo. Assim, o objetivo deste trabalho foi avaliar o espectro de gotas produzidas por pontas de jato plano defletor (TT 11002) e jato plano defletor com indução de ar (TTI 11002), com diferentes adjuvantes adicionados à calda de pulverização, pela técnica de difração de raio laser. O experimento foi conduzido em delineamento inteiramente casualizado, com quatro repetições, em esquema fatorial 2 x 5, ou seja, duas pontas de aplicação (jato plano defletor e jato plano defletor com indução de ar) e cinco composições de calda (água e água mais quatro adjuvantes: fosfatidilcoline+ácido propiônico, éter poliglicólico de monilfenol, ésteres de ácidos graxos e nonil-fenol etoxilado+óxido de etileno). em ambiente controlado, avaliou-se o espectro de gotas, por meio de um analisador a laser de gotas em tempo real, na pressão de 276 kPa. O efeito dos adjuvantes no espectro de gotas mostrou-se dependente da ponta de pulverização empregada. A adição dos adjuvantes à calda não alterou o risco potencial de deriva, expresso pela porcentagem do volume em gotas com diâmetro inferior a 100 µm, porém o adjuvante fosfatidilcoline+ácido propiônico reduziu o diâmetro da mediana volumétrica das gotas produzidas pela ponta de jato plano defletor com indução de ar, em relação à avaliação feita somente com água.

Dispersion and evaporation of droplets amended with adjuvants on soybeans

Quantification of the effects of adjuvants on droplet behaviour on plant surfaces is needed to improve pesticide spray application efficiency for soybeans. Dispersion and evaporation of single 300-μm diameter droplets amended with each of four spray adjuvants at five concentrations were investigated for four soybean plant surfaces (abaxial and adaxial leaflet surfaces, petiole, basal stem). The four adjuvants were a crop oil concentrate (COC), a modified seed oil (MSO), a non-ionic surfactant (NIS) and an oil surfactant blend (OSB). A single-droplet generator was used to produce and deposit 300-μm diameter droplets on target surfaces under controlled environmental conditions. Adjuvants significantly increased the dispersion (or wetted area) of droplets on plant surfaces. Droplet-wetted areas increased with increased adjuvant concentrations but not in direct proportion. The average increases of wetted areas across the four soybean plant surfaces were 443, 462, 416, or 343% when the spray mixture was amended with COC, MSO, NIS or OSB at the manufacturer-recommended concentrations, respectively. Among the four surfaces, the largest wetted area was on the abaxial surface, followed by the adaxial surface, the petiole and then the basal stem. Droplet evaporation times were inversely proportional to the wetted areas. The evaporation time of 300-μm diameter droplets ranged from 36 to 142. s on the four surfaces when the spray mixture was amended with an adjuvant, whereas the water-only droplets ranged from 161 to 190. s. The results demonstrated that use of adjuvants offers great potential to improve the homogeneity of sprayed pesticides, to increase spray coverage and to reduce pesticide application rates on soybean plants. These effects could benefit farmers economically and reduce environmental contamination by pesticides. © 2012.

Avaliação da deposição e da agitação de calda em reservatórios de pulverizadores agrícolas utilizando uma análise numérica (CFD) e experimental

Pós-graduação em Engenharia Mecânica - FEB

An Integrated Study of Pervious Concrete Mixture Design for Wearing Course Applications, July 2011

This report presents the results of the largest and most comprehensive study to date on portland cement pervious concrete (PCPC). It is designed to be widely accessible and easily applied by designers, producers, contractors, and owners. The project was designed to begin with pervious concrete best practices and then to address the unanswered questions in a systematic fashion to allow a successful overlay project. Consequently, the first portion of the integrated project involved a combination of fundamental material property investigations, test method development, and addressing constructability issues before actual construction could take place. The second portion of the project involved actual construction and long-term testing before reporting successes, failures, and lessons learned. The results of the studies conducted show that a pervious concrete overlay can be designed, constructed, operated, and maintained. A pervious concrete overlay has several inherent advantages, including reduced splash and spray and reduced hydroplaning potential, as well as being a very quiet pavement. The good performance of this overlay in a particularly harsh freeze-thaw climate, Minnesota, shows pervious concrete is durable and can be successfully used in freeze-thaw climates with truck traffic and heavy snow plowing.

Characterizing emission and breathing-zone concentrations following exposure cases to fluororesin-based waterproofing spray mists.

Measurements and simulations were performed to assess workers' exposure to solvent vapors and aerosols during the waterproofing of a tiled surface. This investigation followed two recent incidents in the same company where workers experienced acute respiratory illness after spraying a stain-repellent resin containing fluorinated polymers on stone-tiled walls and floors. Because the waterproofing activity had been done for years at the tile company without encountering any exposure problems prior to these cases, it was strongly suspected that the incidents were linked to a recent change in the composition of the coating mixture. Experimental measurements and simulations indicated that the emission rate of particles smaller than 10 microm may be estimated at 0.66 mg/sec (SD 0.10) for the old resin and at 0.37 mg/sec (SD 0.04) for the new one. The measurement of the solvent emission rate from surfaces coated with the two resins indicated that shortly after spraying, the emission was in the range of 18 to 20 mg/sec x m2 and was similar for both products. Solvent and overspray emission rates were introduced in a two-zone compartment model. The results obtained in the near-field indicate significant exposure to overspray mist (7 and 34 mg/m3 for new resin) and solvent vapors (80 to 350 ppm for the new resin). It was also shown that the introduction of the new resin tended to significantly decrease the levels of solvents and particulates in the workers' breathing zone. These results strongly suggest that cases of acute respiratory illness are related to the specific toxicity of the fluorinated polymer itself. The fact that the same polymer is used in various commercial products raises concern regarding other possible occupational and domestic exposures.

Improving diquat efficacy on grasses by adding adjuvants to the spray solution before use

The effect of five adjuvants (non-ionic surfactant, paraffinic oil, vegetable oil, mixture of fatty acids methyl esters plus surfactant blend, and organosilicone) on diquat efficacy was assessed on poverty brome, sterile oat, and Italian ryegrass in field and pot experiments. All tank mixtures with diquat increased diquat efficacy from 50-54% to 77-98% as for fresh weight reduction, indicating significant enhancement of diquat efficacy on grasses. The increased efficacy was most likely attributed to better droplet retention and diffusion on the leaf surfaces. When combined with non-ionic surfactant, diquat showed slightly more rapid control of grass weeds (i.e. symptoms were visible within a few hours after application).

The use of spray drying technology to reduce bitter taste of casein hydrolysate

The utilization of protein hydrolysates in food systems is frequently hindered due to their bitterness and hygroscopicity. Spray drying technology could be an alternative for reducing these problems. The aim of this work was to reduce or to mask the casein hydrolysate bitter taste using spray drying and mixtures of gelatin and soy protein isolate (SPI) as carriers. Six formulations were studied: three with 20% of hydrolysate and 80% of mixture (gelatine/SPI at proportions of 50/50, 40/60 and 60/40%) and three with 30% of hydrolysate and 70% of mixture (gelatine/SPI at proportions of 50/50, 40/60 and 60/40%). The spray-dried formulations were evaluated by SEM, hygroscopicity, thermal behavior (DSC), dissolution, and bitter taste, by a trained sensory panel using a paired-comparison test (free samples vs. spray-dried samples); all samples were presented in powder form. SEM analysis showed mostly spherically shaped particles, with many concavities and some particles with pores. All formulations were oil and water compatible and showed lower hygroscopicity values than free casein hydrolysate. At Aw 0.83, the free hydrolysate showed Tg about 25 degrees C lower than the formulations, indicating that the formulations may be more stable at Aw >= 0.65 since the glass transition should be prevented. The sensory panel found the formulations, tasted in the powder form, to be less bitter (P < 0.05) than the free casein hydrolysate. These results indicated that spray drying of casein hydrolysate with mixtures of gelatin and SPI was successful to attenuate the bitterness of casein hydrolysate. Thus, spray drying widens the possibilities of application of casein hydrolysates. (C) 2009 Elsevier Ltd. All rights reserved.

Choice of tracers for the evaluation of spray deposits

As substâncias traçadoras são usadas para avaliar a eficácia de pulverizações mas, normalmente, elas modificam a tensão superficial de soluções aquosas. O trabalho objetivou definir um método para avaliar a distribuição e a quantidade de produto depositada em pulverizações, utilizando-se substâncias traçadoras, com a possibilidade de ajustar a tensão superficial da calda. Foram testados os produtos Azul Brilhante a 0,15%, Saturn Yellow a 0,15% suspenso em lignosulfonato Vixilperse a 0,015% e a Fluoresceína Sódica a 0,005%, e as misturas de Azul Brilhante mais Saturn Yellow e Azul Brilhante mais Fluoresceína, nas mesmas concentrações. Para avaliar a degradação as soluções com os produtos foram depositados sobre folhas de citros e avaliados as quantidades através da leitura de unidade de fluorescência e densidade óptica, das soluções sem secar, secas no escuro, exposta ao sol por 2, 4 e 8 horas e comparadas com as leituras obtidas com os depósitos direto em água. A tensão superficial da solução traçadora foi determinada pela passagem de gotas formadas no período entre 20 e 40 segundos. A mistura do Azul Brilhante mais o Saturn Yellow a 0,15%, não apresentou degradação em todas as condições de avaliação, não foi absorvida pelas folhas e manteve a solução na mesma tensão superficial da água, possibilitando ajustá-la aos mesmos níveis das concentrações dos produtos fitossanitários. Isto proporcionou o estabelecimento de um método qualitativo pela avaliação visual sobre luz ultravioleta da distribuição do pigmento e quantitativo com a determinação da quantidade depositada do corante numa mesma solução, em diferentes tensões superficiais na calda de pulverização.

Leaf spray fertilization of boron and zinc on productivity and fruit quality of Japanese pear tree

The cultivation of fruit plants from temperate climate in tropical or subtropical regions can be a good income alternative for the producer. However, due to the little existent information about cultivation of those fruit plants, the producers use imported techniques of other producing areas, or even an association of practices used for other fruit plants, pointing out the leaf spray fertilization of micronutrients without appropriate scientific base. In this context, the objective of this study was to verify the effect of the leaf spray fertilization of B and Zn on productivity and fruit quality of Japanese pear tree. The experiment was conducted from 2004 to 2005, in Ilha Solteira, in northwestern São Paulo State-Brazil. The climate is, according to the Köpppen Classification, tropical wet and dry (Aw). The 'Okusankichi' cultivar, grafted on Pyrus communis L. rootstock was used as well as doses of 110 g.ha-1 of B and 250 g.ha-1 of Zn in each application. The treatments were: T1. water, T2. boric acid, T3. zinc sulfate, T4. T2 + T3, T5. boric acid + urea + citric acid + EDTA, T6. zinc sulfate + urea + citric acid + EDTA, T7. T5 + T6, T8. boric acid + urea + citric acid + EDTA + sodium molibdate + sulfur + calcium chloride, T9. zinc sulfate + urea + citric acid + EDTA + Fe sulfate + Mn sulfate + Mg sulfate and, T10. T8+T9. A randomized blocks design was used and the averages were compared by Tukey test. In the first crop the mixture of boric acid with quelating agents were efficient to supply B to the plants and zinc sulfate plus quelating agents were efficient to increase Zn leaf content. However, the productivity and the fruit quality were not influenced by the leaf spray of B and Zn. In the second crop the leaf content of B and Zn and the productivity were not influenced by the leaf spray; the boric acid and the zinc sulfate with or without quelating agents increased the contents of total soluble solids and, the boric acid with or without quelating agents increased the contents of total titratable acidity.

Spray Nozzles, Pressures, Additives and Stirring Time on Viability and Pathogenicity of Entomopathogenic Nematodes (Nematoda: Rhabditida) for Greenhouses

The objective of this study was to evaluate different strategies for the application of entomopathogenic nematodes (EPN). Three different models of spray nozzles with air induction (AI 11003, TTI 11003 and AD-IA 11004), three spray pressures (207, 413 and 720 kPa), four different additives for tank mixtures (cane molasses, mineral oil, vegetable oil and glycerin) and the influence of tank mixture stirring time were all evaluated for their effect on EPN (Steinernema feltiae) viability and pathogenicity. The different nozzles, at pressures of up to 620 kPa, were found to be compatible with S. feltiae. Vegetable oil, mineral oil and molasses were found to be compatible adjuvants for S. feltiae, and stirring in a motorized backpack sprayer for 30 minutes did not impact the viability or pathogenicity of this nematode. Appropriate techniques for the application of nematodes with backpack sprayers are discussed. © 2013 Moreira et al.

Célula solar de SnO2/TiO2 preparada por spray - pirólise ativada com corante orgânico

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)