Impedance parameters and the state-of-charge. III. Zinc-manganese dioxide and magnesium-manganese dioxide dry batteries

The problem of non-destructive determination of the state-of-charge of zinc- and magnesium-manganese dioxide dry batteries is examined experimentally from the viewpoint of internal impedance and open-circuit voltage at equilibrium. It is shown that the impedance is mainly charge-transfer controlled at relatively high states-of-charge and progressively changes over to diffusion control as the state-of-charge decreases in the case of zinc-manganese dioxide dry batteries. On the other hand, the impedance is mainly diffusion controlled for undischarged batteries but becomes charge-transfer controlled as soon as there is some discharge in the case of magnesium-manganese dioxide batteries. It is concluded that the determination of state-of-charge is not possible for both types of batteries by the measurement of impedance parameters due to film-induced fluctuations of these parameters. The measurement of open-circuit voltage at equilibrium can be used as a state-of-charge indicator for Zn-MnO2 batteries but not for Mg-MnO2 batteries.

回转窑热解处理废锌锰电池试验研究

我国电池生产量已经达到209亿节（2003年），多年来一直占据世界第一大电池生产国的地位，其中锌锰电池占大多数。废锌锰电池丢弃后，其中的重金属物质会逐渐渗透到地下，污染土壤和水体。重金属在生物体内富集，会使生物体致畸或致变。但同时，废锌锰电池中也含有大量有用的资源如锌、二氧化锰等。应对其进行回收利用，变废为宝。本文介绍了废锌锰电池回收处理的主要技术及研究进展，不同的处理技术回收废锌锰电池时的目标产物各不相同，但一般可分为以下几种：以单质形式回收锌、锰和汞；以合金的形式回收锌和锰；回收锌和二氧化锰；回收各金属元素制备复合微量元素肥料；回收锌、锰元素制备锰锌铁氧体；回收锌、锰元素制备硫酸锌和碳酸锰等。本文对一些废锌锰电池回收处理技术的优缺点从无害化程度、资源化程度、产品等级、工艺要求以及二次污染五个方面进行了分析和比较。在对国内外废锌锰电池回收处理技术进行分析比较的基础上提出了一种成本较低、可操作性较强的处理技术：先以干法除去废锌锰电池中的汞，然后以湿法除去其它的有害重金属并进一步加工制备有机螯合微量元素肥料。 本文以回转窑中物料停留时间的经验公式和传热学的知识设计和计算了回转窑的长度和内径尺寸、电热丝的功率以及外围的保温材料厚度等参数。用保温材料和润滑油相结合的方式对回转窑的连接部分实行密封。通过调整回转窑的转速和回转窑支架两端高度差的方式控制物料在回转窑中的停留时间，从而调节热解时间的长短。利用自动控制设备调节电热丝的功率从而调节试验中的热解温度。利用该回转窑在不同条件下对热解处理废锌锰电池进行了试验研究，热解过程中产生的尾气和颗粒物用一系列吸收液进行吸收和固定。 在热解试验中改变影响热解过程的三种因素：热解温度、热解时间和载气流速并按三因素四水平的正交方法安排试验。改变废锌锰电池热解过程中的热解温度、热解时间和载气流速三种因素进行正交试验并利用正交统计学的方法分析了这三种因素对热解除汞率的影响。利用ICP检测仪测定了各吸收液中汞的含量，并分析热解气体产物经过系列吸收液时汞被吸收的情况以及汞的形态分布。利用气相色谱仪对尾气成分进行了测定，并对热解过程中产气的过程和规律进行了分析。用X射线衍射测试的方法研究了热解前后锌锰电池的物质形态变化情况。对除汞率的正交统计分析表明，合适的热解条件为：热解温度690℃，热解时间100min，载气流速0.06m3/h，在这种试验条件下热解处理废锌锰电池的除汞率达到100%。同时还得到：热解时间对除汞效果影响最大，热解温度次之，载气流速的影响较小。ICP测试的结果表明：热解尾气在经过试验中设置的吸收瓶后，其中的汞被完全吸收，尾气中95%以上的汞以单质的形式存在。气相色谱分析的结果表明，热解开始后，废锌锰电池中的有机质迅速分解，其产物为C2H4、CH4和H2等。一段时间后，有机质的分解量大幅度减少，同时废电池中的石墨碳和高价金属氧化物发生氧化还原反应，生成CO气体。对废锌锰电池原料以及热解残渣的X射线衍射分析表明，当热解温度为350℃时，X射线衍射图谱上2θ值为35°附近的区域有新峰出现，但不明显，说明有结晶体形成但量不大。500℃时上述峰明显增强，这是由于ZnO和FeO形成了结晶体，同时在2θ值为41°附近有新峰出现，这是高价锰氧化物与石墨碳发生氧化还原反应生成了MnO并形成了结晶体。650℃时，2θ值在41°附近的峰显著增强，且热解过程中形成的峰稳定下来，基本上不再有新的结晶体生成。热解后，高价锰氧化物的相对含量从32.2%下降到4.6%，而MnO的相对含量则从6.4%上升到38.6%。热解后的残渣中晶体物质含量大，金属元素大多以低价态存在，适合于制备有机螯合微量元素肥料。

INVESTIGATION OF MAGNESIUM ION CHARGE STORAGE MECHANISM IN MANGANESE DIOXIDE

Magnesium (Mg) battery is considered as a promising candidate for the next generation battery technology that could potentially replace the current lithium (Li)-ion batteries due to the following factors. Magnesium possesses a higher volumetric capacity than commercialized Li-ion battery anode materials. Additionally, the low cost and high abundance of Mg compared to Li makes Mg batteries even more attractive. Moreover, unlike metallic Li anodes which have a tendency to develop a dendritic structure on the surface upon the cycling of the battery, Mg metal is known to be free from such a hazardous phenomenon. Due to these merits of Mg as an anode, the topic of rechargea¬ble Mg batteries has attracted considerable attention among researchers in the last few decades. However, the aforementioned advantages of Mg batteries have not been fully utilized due to the serious kinetic limitation of Mg2+ diffusion process in many hosting compounds which is believed to be due to a strong electrostatic interaction between divalent Mg2+ ions and hosting matrix. This serious kinetic hindrance is directly related to the lack of cathode materials for Mg battery that provide comparable electrochemical performances to that of Li-based system. Manganese oxide (MnO2) is one of the most well studied electrode materials due to its excellent electrochemical properties, including high Li+ ion capacity and relatively high operating voltage (i.e., ~ 4 V vs. Li/Li+ for LiMn2O4 and ~ 3.2 V vs. Mg/Mg2+). However, unlike the good electrochemical properties of MnO2 realized in Li-based systems, rather poor electrochemical performances have been reported in Mg based systems, particularly with low capacity and poor cycling performances. While the origin of the observed poor performances is believed to be due to the aforementioned strong ionic interaction between the Mg2+ ions and MnO2 lattice resulting in a limited diffusion of Mg2+ ions in MnO2, very little has been explored regarding the charge storage mechanism of MnO2 with divalent Mg2+ ions. This dissertation investigates the charge storage mechanism of MnO2, focusing on the insertion behaviors of divalent Mg2+ ions and exploring the origins of the limited Mg2+ insertion behavior in MnO2. It is found that the limited Mg2+ capacity in MnO2 can be significantly improved by introducing water molecules in the Mg electrolyte system, where the water molecules effectively mitigated the kinetic hindrance of Mg2+ insertion process. The combination of nanostructured MnO2 electrode and water effect provides a synergic effect demonstrating further enhanced Mg2+ insertion capability. Furthermore, it is demonstrated in this study that pre-cycling MnO2 electrodes in water-containing electrolyte activates MnO2 electrode, after which improved Mg2+ capacity is maintained in dry Mg electrolyte. Based on a series of XPS analysis, a conversion mechanism is proposed where magnesiated MnO2 undergoes a conversion reaction to Mg(OH)2 and MnOx and Mn(OH)y species in the presence of water molecules. This conversion process is believed to be the driving force that generates the improved Mg2+ capacity in MnO2 along with the water molecule’s charge screening effect. Finally, it is discussed that upon a consecutive cycling of MnO2 in the water-containing Mg electrolyte, structural water is generated within the MnO2 lattice, which is thought to be the origin of the observed activation phenomenon. The results provided in this dissertation highlight that the divalency of Mg2+ ions result in very different electrochemical behaviors than those of the well-studied monovalent Li+ ions towards MnO2.

Effect of manganese dioxide on the thermal decomposition of ammonium perchlorate

Thermal decomposition of powdered ammonium perchlorate, catalysed by manganese dioxide (MnO2), has been studied in the low concentration ranges of the catalyst. MnO2 sensitises the thermal decomposition of ammonium perchlorate. The activation energy estimations of catalysed ammonium perchlorate show that the value is about 30 kcal/mol throughout the low and the high temperature regions whereas uncatalysed ammonium perchlorate gives two activation energies, 20 kcal/mol in the low temperature region (280-320°C) and 60 kcal/mol in the higher temperature region (350-390°C). This behaviour has been explained on the basis of an electron transfer process. The effectiveness of MnO2 in the thermal decomposition further increases on pre-heating the sample at 50°C for two weeks; manganese ions enter the ammonium perchlorate lattice during the process of pre-heating.

Abatement of fluoride from water using manganese dioxide-coated activated alumina

Batch adsorption of fluoride onto manganese dioxide-coated activated alumina (MCAA) has been studied. Adsorption experiments were carried out at various pH (3–9), time interval (0–6 h), adsorbent dose (1–16 g/l), initial fluoride concentration (1–25 mg/l) and in the presence of different anions. Adsorption isotherms have been modeled using Freundlich, Langmuir and Dubinin–Raduskevich isotherms and adsorption followed Langmuir isotherm model. Kinetic studies revealed that the adsorption followed second-order rate kinetics. MCAA could remove fluoride effectively (up to 0.2 mg/l) at pH 7 in 3 h with 8 g/l adsorbent dose when 10 mg/l of fluoride was present in 50 ml of water. In the presence of other anions, the adsorption of fluoride was retared. The mechanism of fluoride uptake by MCAA is due to physical adsorption as well as through intraparticle diffusion which was confirmed by kinetics, Dubinin–Raduskevich isotherm, zeta-potential measurements and mapping studies of energy-dispersive analysis of X-ray.

Synthesis and electrocatalytic properties of manganese dioxide for non-enzymatic hydrogen peroxide sensing

Manganese dioxide nanoparticles were synthesized by chemical reduction route at different growth temperatures of 40 degrees C, 80 degrees C, 100 degrees C and were characterized using X-ray Diffraction (XRD), Field emission scanning electron microscopy (FESEM), X-ray photoelectron spectroscopy (XPS), Cyclic Voltammetry (CV) and chronoamperometry (CA) analysis. FESEM results show that on increasing growth temperature the morphology changes from clusters into mixture of rods and flakes. XPS analysis reveals the formation of MnO2. Then these particles were immobilized on Pt electrode. A platinum (Pt) electrode modified with low dimensional MnO2 was investigated as a chronoamperometric (CA) sensor for hydrogen peroxide sensing (H2O2). The sample prepared at 100 degrees C shows good electrocatalytic ability for H2O2 sensing when compared with the samples prepared at 40 degrees C and 80 degrees C. At an operating potential of 0.3 V vs. Ag/AgCl catalytic oxidation of the analyte is measured for chronoamperometric (CA) monitoring. The CA signals are linearly proportional to the concentration of H2O2. It is also found that the morphology of the nanostructure plays a vital role in the detection of H2O2. (C) 2014 Elsevier Ltd. All rights reserved.

Manganese dioxide allylic and benzylic oxidation reactions in ionic liquids

Ionic liquids 1-butyl-3-methylimidazolium tetrafluoroborate [bmIm][BF₄] and 1-butyl-3-methylimidazolium hexafluorophosphate [bmIm][PF₆] were evaluated as reaction media for allylic and benzylic oxidation reactions using manganese dioxide. The use of ionic liquids as an extractant in the reaction work-up was also investigated. Procedures for recycling of the [bmIm][PF₆] ionic liquids used in these MnO₂ oxidation reactions were also developed.

Biobsorbent properties of biosolids for aqueous zinc, manganese and cyanide removal

Biosolids were used to remove zinc, manganese and cyanide from mining wastewaters. The effect of aqueous parameters and reaction variables on contaminant biosorption was quantified. The mechanism of removal was adsorption onto amine and carboxyl functional groups. Immobilisation was investigated to overcome problems of swelling and disintegration of the biosolids.

Concentration of Manganese Dioxide from Philipsburg, Montana

Imports of manganese ore probably supply a major proportion of the needs of the United States. Domestic production is reported to be higher than pre-war levels, but does not equal that of the peak production year of 1943. In 1946, the Anaconda Copper Mining Company ac­counted for 90 percent of the total shipments of mangan­ese nodules, and this company is the largest producer of domestic metallurgical ore in the United States.

Selective Transport of Zinc, Manganese, Nickel, Cobalt and Cadmium in the Root System and Transfer to the Leaves in Young Wheat Plants

• Background and Aims The uptake, translocation and redistribution of the heavy metals zinc, manganese, nickel, cobalt and cadmium are relevant for plant nutrition as well as for the quality of harvested plant products. The long-distance transport of these heavy metals within the root system and the release to the shoot in young wheat (Triticum aestivum ‘Arina’) plants were investigated. • Methods After the application of 65Zn, 54Mn, 63Ni, 57Co and 109Cd for 24 h to one seminal root (the other seminal roots being excised) of 54-h-old wheat seedlings, the labelled plants were incubated for several days in hydroponic culture on a medium without radionuclides. • Key Results The content of 65Zn decreased quickly in the labelled part of the root. After the transfer of 65Zn from the roots to the shoot, a further redistribution in the phloem from older to younger leaves was observed. In contrast to 65Zn, 109Cd was released more slowly from the roots to the leaves and was subsequently redistributed in the phloem to the youngest leaves only at trace levels. The content of 63Ni decreased quickly in the labelled part of the root, moving to the newly formed parts of the root system and also accumulating transiently in the expanding leaves. The 54Mn content decreased quickly in the labelled part of the root and increased simultaneously in leaf 1. A strong retention in the labelled part of the root was observed after supplying 57Co. • Conclusions The dynamics of redistribution of 65Zn, 54Mn, 63Ni, 57Co and 109Cd differed considerably. The rapid redistribution of 63Ni from older to younger leaves throughout the experiment indicated a high mobility in the phloem, while 54Mn was mobile only in the xylem and 57Co was retained in the labelled root without being loaded into the xylem.

Ambient temperature, zinc ion-conducting, binary molten electrolyte based on acetamide and zinc perchlorate: Application in rechargeable zinc batteries

Binary room temperature molten electrolytes based on acetamide and zinc perchlorate have been prepared and characterized. The electrolytes are found to be highly zinc ion-conducting with very favorable physicochemical and electrochemical characteristics. Raman and infrared spectroscopic studies reveal the presence of large free-ion concentration in the molten liquid. This is corroborated by the high conductivity observed under ambient conditions. Rechargeable zinc batteries assembled using gamma-MnO2 as the cathode and Zn as the anode with the molten electrolyte show high discharge capacities over several cycles, indicating excellent reversibility. This unique class of acetamide-based, room temperature molten liquids may become viable and green alternative electrolytes for rechargeable zinc-based secondary batteries. (C) 2009 Elsevier Inc. All rights reserved.