Monitoramento do agrotóxico mancozeb no solo em diferentes sistemas de plantios de tomate

O presente trabalho tem por objetivo monitorar o agrotóxico Mancozeb no solo em diferentes sistemas de plantios de tomate utilizando a metodologia de decomposição dos ditiocarbamatos (DTCs) com geração de dissulfeto de carbono (CS2). Este método é amplamente utilizado na determinação dos resíduos de DTCs em alimentos, tendo sido adaptado para trabalhar com amostras de solo artificiais e reais. O método foi avaliado utilizando amostras contaminadas artificialmente a partir de uma amostra de solo controle, proveniente da Amazônia. A contaminação foi realizada com uma solução de campo (2 g.L-1 em água) do agrotóxico Manzate 800 (Mancozeb). A partir do momento em que foram determinadas as condições ideais de operação do método de decomposição dos DTCs, analisou-se o teor de Mancozeb em amostras reais, provenientes de uma área cultivada com tomate, no Município de São José de Ubá (RJ), sob sistemas de Plantios Convencional, Mínimo e Direto. Foi possível constatar a presença de teores de Mancozeb nas amostras reais de solo em estudo, coletadas nas profundidades 0 - 5 cm; 5 - 10 cm; 10 - 20 cm e 20 - 40 cm. Os resultados mostraram que os solos provenientes dos sistemas convencional e mínimo apresentaram, na camada superficial, um teor de Mancozeb de (7,44 mg.kg-1 e 5,70 mg.kg-1) superior ao obtido no sistema direto, que apresentou teores de (1,14 mg.kg-1 e 1,95 mg.kg-1) de Mancozeb

Study of pesticide effects on non-target organisms

A utilização insustentável de pesticidas, especialmente em zonas com elevado valor ecológico constitui uma ameaça à integridade dos ecossistemas. Sendo um problema à escala mundial, e também no contexto nacional, o presente trabalho pretende ser um contributo para a avaliação dos efeitos de pesticidas em organismos não alvo terrestres e, principalmente, aquáticos, em contextos de progressiva relevância ecológica. Neste sentido, o estudo foi direccionado para áreas (A1 e A2) integradas numa zona agrícola extensa em Portugal, utilizada para a produção de milho e, principalmente, de arroz (Baixo Mondego), a qual sustenta uma elevada biodiversidade. O estudo teve início na área A1, onde a monitorização físico-química e os ensaios com amostras naturais (ensaios WET - whole effluent tests) provenientes desta área evidenciaram que, apesar da ausência de pesticidas, as amostras de água colhidas no canal que atravessava os arrozais foram as mais nocivas para o crescimento de Pseudokirchneriella subcapitata e Chlorella vulgaris. Uma vez que outras fontes de contaminação (produção de gado) actuavam em A1, o estudo prosseguiu apenas na área A2. Assim, em A2, começou-se por determinar a toxicidade individual e da mistura de dois herbicidas formulados aplicados nos campos de arroz (Viper®) e milho (Mikado®) em condições laboratoriais. Viper® foi o herbicida mais tóxico, tanto para o crescimento de P. subcapitata e C. vulgaris, como para a sobrevivência, reprodução e crescimento de Daphnia longispina e Daphnia magna. Adicionalmente, estimou-se que a mistura Viper®/Mikado® induz efeitos antagonistas no crescimento de P. subcapitata e efeitos sinérgicos no crescimento de C. vulgaris e na sobrevivência dos dafnídeos. A avaliação da toxicidade destes herbicidas formulados e seus ingredientes activos no comportamento de minhocas terrestres (Eisenia andrei), usando solos naturais, demonstrou que Viper® e penoxsulam causaram uma % de evitamento superior nos organismos expostos. Contudo, o risco para E. andrei será à partida reduzido se as taxas de aplicação dos herbicidas forem respeitadas. Ensaios WET foram novamente usados para testar amostras naturais da área A2. Verificou-se que a qualidade do sistema aquático e do arrozal diminuiu durante a estação agrícola, em paralelo com a presença de nutrientes e pesticidas. O crescimento algal foi inibido, apesar dos parâmetros de história de vida dos dafnídeos terem sido estimulados. O resultado desta avaliação subestimou, em certos casos, os impactos reais causados pela aplicação de pesticidas. A avaliação in situ simultânea à aplicação de herbicidas nos arrozais demonstrou que os efeitos registados foram de facto restritos aos pulsos de herbicidas. A inibição das taxas de alimentação de D. longispina e D. magna forneceram um sinal precoce de alterações no sistema, seguido pela diminuição da sua sobrevivência e do crescimento de P. subcapitata. Em suma, as diferentes fases da avaliação efectuada confirmaram a existência de condições desfavoráveis devido às práticas agrícolas, reforçando a necessidade de se conjugar ensaios laboratoriais com avaliações in situ de maior relevância ecológica, para reduzir o grau de incerteza aliado à determinação dos riscos.

Evaluation of the contamination level and proposal of remediation of soils in the basin of a processing plant of heavy metals, under a tropical climate, in Minas Gerais, Brazil

Indústrias metalúrgicas de produção de ligas metálicas podem por em risco toda a área envolvente, nomeadamente a qualidade das águas (superficiais e subterrâneas), dos solos e do ar, sempre que não existam infraestruturas e planos adequados de gestão destes resíduos. No caso em estudo, a unidade industrial situa-se na bacia do rio São Francisco, no estado brasileiro de Minas Gerais, e nos mais de quarenta anos de funcionamento tem produzido inúmeros problemas ambientais. Este estudo baseia-se nos primeiros resultados referentes aos solos da envolvente, tendo como objetivos a identificação dos principais contaminantes e a definição da área contaminada, de forma a avaliar a eficácia de projetos futuros de recuperação.

Determination of chlorfenvinphos in soils by microwave-assisted extraction and stripping voltammetry with an ultramicroelectrode

A methodology for the determination of the pesticide chlorfenvinphos by microwave-assisted solvent extraction and square-wave cathodic stripping voltammetry at a mercury film ultramicroelectrode in soil samples is proposed. Optimization of microwave solvent extraction performed with two soils, selected for having significantly different properties, indicated that the optimum solvent for extracting chlorfenvinphos is hexane-acetone (1:1, v/v). The voltammetric procedure is based on controlled adsorptive accumulation of the insecticide at the potential of -0.60 V (vs. Ag/AgCl) in the presence of Britton-Robinson buffer (pH 6.2). The detection limit obtained for a 10 s collection time was 3.0 x 10-8 mol l-1. The validity of the developed methodology was assessed by recovery experiments at the 0.100 µg g-1 level. The average recoveries and standard deviations for the global procedure reached byMASE-square-wave voltammetry were 90.2±2.8% and 92.1±3.4% for type I (soil rich in organic matter) and type II (sandy soil) samples, respectively. These results are in accordance to the expected values which show that the method has a good accuracy.

Determination of ametryn in soils via microwave-assisted solvent extraction coupled to anodic stripping voltammetry with a gold ultramicroelectrode

An extraction-anodic adsorptive stripping voltammetric procedure using microwave-assisted solvent extraction and a gold ultramicroelectrode was developed for determining the pesticide ametryn in soil samples. The method is based on the use of acetonitrile as extraction solvent and on controlled adsorptive accumulation of the herbicide at the potential of 0.50 V (vs. Ag/AgCl) in the presence of Britton-Robinson buffer (pH 3.3). Soil sample extracts were analysed directly after drying and redissolution with the supporting electrolyte but without other pre-treatment. The limit of detection obtained for a 10 s collection time was 0.021 µg g-1. Recovery experiments for the global procedure, at the 0.500 µg g-1 level, gave satisfactory mean and standard deviation results which were comparable to those obtained by HPLC with UV detection.

Analysis of pesticide residues in strawberries and soils by GC-MS/MS, LC-MS/MS and two-dimensional GC-timeof- flight MS comparing organic and integrated pest management farming

This study analysed 22 strawberry and soil samples after their collection over the course of 2 years to compare the residue profiles from organic farming with integrated pest management practices in Portugal. For sample preparation, we used the citrate-buffered version of the quick, easy, cheap, effective, rugged, and safe (QuEChERS) method. We applied three different methods for analysis: (1) 27 pesticides were targeted using LC-MS/MS; (2) 143 were targeted using low pressure GC-tandem mass spectrometry (LP-GC-MS/MS); and (3) more than 600 pesticides were screened in a targeted and untargeted approach using comprehensive, two-dimensional gas chromatography time-of-flight mass spectrometry (GC × GC-TOF-MS). Comparison was made of the analyses using the different methods for the shared samples. The results were similar, thereby providing satisfactory confirmation of both similarly positive and negative findings. No pesticides were found in the organic-farmed samples. In samples from integrated pest management practices, nine pesticides were determined and confirmed to be present, ranging from 2 μg kg−1 for fluazifop-pbutyl to 50 μg kg−1 for fenpropathrin. Concentrations of residues in strawberries were less than European maximum residue limits.

Fertilizer and pesticide movement from citrus groves in Florida flatwood soils /

Mode of access: Internet.

The determination of three selected sites for the construction and operation of a low level radioactive waste storage and burial facility

Radioactive wastes are by-products of the use of radiation technologies. As with many technologies, the wastes are required to be disposed of in a safe manner so as to minimise risk to human health. This study examines the requirements for a hypothetical repository and develops techniques for decision making to permit the establishment of a shallow ground burial facility to receive an inventory of low-level radioactive wastes. Australia’s overall inventory is used as an example. Essential and desirable siting criteria are developed and applied to Australia's Northern Territory resulting in the selection of three candidate sites for laboratory investigations into soil behaviour. The essential quantifiable factors which govern radionuclide migration and ultimately influence radiation doses following facility closure are reviewed. Simplified batch and column procedures were developed to enable laboratory determination of distribution and retardation coefficient values for use in one-dimensional advection-dispersion transport equations. Batch and column experiments were conducted with Australian soils sampled from the three identified candidate sites using a radionuclide representative of the current national low-level radioactive waste inventory. The experimental results are discussed and site soil performance compared. The experimental results are subsequently used to compare the relative radiation health risks between each of the three sites investigated. A recommendation is made as to the preferred site to construct an engineered near-surface burial facility to receive the Australian low-level radioactive waste inventory.

DDT resistance and transformation by different microbial strains isolated from DDT-contaminated soils and compost materials

Bioremediation is a potential option to treat 1, 1, 1-trichloro-2, 2 bis (4-chlorophenyl) ethane (DDT) contaminated sites. In areas where suitable microbes are not present, the use of DDT resistant microbial inoculants may be necessary. It is vital that such inoculants do not produce recalcitrant breakdown products e.g. 1, 1-dichloro-2, 2-bis (4-chlorophenyl) ethylene (DDE). Therefore, this work aimed to screen DDT-contaminated soil and compost materials for the presence of DDT-resistant microbes for use as potential inoculants. Four compost amended soils, contaminated with different concentrations of DDT, were used to isolate DDT-resistant microbes in media containing 150 mg I -1 DDT at three temperatures (25, 37 and 55°C). In all soils, bacteria were more sensitive to DDT than actinomycetes and fungi. Bacteria isolated at 55°C from any source were the most DDT sensitive. However DDT-resistant bacterial strains showed more promise in degrading DDT than isolated fungal strains, as 1, 1-dichloro 2, 2-bis (4-chlorophenyl) ethane (DDD) was a major bacterial transformation product, while fungi tended to produce more DDE. Further studies on selected bacterial isolates found that the most promising bacterial strain (Bacillus sp. BHD-4) could remove 51% of DDT from liquid culture after 7 days growth. Of the amount transformed, 6% was found as DDD and 3% as DDE suggesting that further transformation of DDT and its metabolites occurred.

Temporal trend of pesticide concentrations in the Chikugo River (Japan) with changes in environmental regulation and field infrastructure

Contamination of pesticides, which are applied to rice paddy fields, in river water has been a major problem in Japan for decades. A prolonged water holding period after pesticide application in paddy fields is expected to reduce the concentration of rice pesticides in river water. Therefore, a long monitoring campaign was conducted from 2004 to 2010 to measure the concentrations of pesticides in water samples collected from several points along the Chikugo River (Japan) including tributaries and the main stream to see if there was any reduction in the level of pesticide contamination after the extension of the water holding period (from 3–4 days to 7 days) was introduced in 2007 by the new water management regulation. No significant difference (p > 0.05) was found in pesticide concentrations between the periods before and after 2007 in all monitoring points, except in one tributary where the pesticide concentrations after 2007 were even higher than that of the previous period. A detailed study in one of the tributaries also revealed that the renovated infrastructure did not reduce the pesticide concentrations in the drainage canals. Neither the introduction of the new regulation nor the improved infrastructure had any significant effect on reducing the contamination of pesticides in water of the Chikugo River. It is probably because most farmers did not properly implement the new requirement of holding paddy water within the field for 7 days after the application of pesticides. Only tightening the regulation would not be sufficient and more actions should be taken to enforce/provide extension support for the new water management regulation in order to reduce the level of residual pesticides in river water in Japan.

Pesticide residues in food - acute dietary exposure

Consumer risk assessment is a crucial step in the regulatory approval of pesticide use on food crops. Recently, an additional hurdle has been added to the formal consumer risk assessment process with the introduction of short-term intake or exposure assessment and a comparable short-term toxicity reference, the acute reference dose. Exposure to residues during one meal or over one day is important for short-term or acute intake. Exposure in the short term can be substantially higher than average because the consumption of a food on a single occasion can be very large compared with typical long-term or mean consumption and the food may have a much larger residue than average. Furthermore, the residue level in a single unit of a fruit or vegetable may be higher by a factor (defined as the variability factor, which we have shown to be typically ×3 for the 97.5th percentile unit) than the average residue in the lot. Available marketplace data and supervised residue trial data are examined in an investigation of the variability of residues in units of fruit and vegetables. A method is described for estimating the 97.5th percentile value from sets of unit residue data. Variability appears to be generally independent of the pesticide, the crop, crop unit size and the residue level. The deposition of pesticide on the individual unit during application is probably the most significant factor. The diets used in the calculations ideally come from individual and household surveys with enough consumers of each specific food to determine large portion sizes. The diets should distinguish the different forms of a food consumed, eg canned, frozen or fresh, because the residue levels associated with the different forms may be quite different. Dietary intakes may be calculated by a deterministic method or a probabilistic method. In the deterministic method the intake is estimated with the assumptions of large portion consumption of a ‘high residue’ food (high residue in the sense that the pesticide was used at the highest recommended label rate, the crop was harvested at the smallest interval after treatment and the residue in the edible portion was the highest found in any of the supervised trials in line with these use conditions). The deterministic calculation also includes a variability factor for those foods consumed as units (eg apples, carrots) to allow for the elevated residue in some single units which may not be seen in composited samples. In the probabilistic method the distribution of dietary consumption and the distribution of possible residues are combined in repeated probabilistic calculations to yield a distribution of possible residue intakes. Additional information such as percentage commodity treated and combination of residues from multiple commodities may be incorporated into probabilistic calculations. The IUPAC Advisory Committee on Crop Protection Chemistry has made 11 recommendations relating to acute dietary exposure.

Optimum design of cantilever sheet pile walls in sandy soils using inverse reliability approach

In this paper an approach for obtaining depth and section modulus of the cantilever sheet pile wall using inverse reliability method is described. The proposed procedure employs inverse first order reliability method to obtain the design penetration depth and section modulus of the steel sheet pile wall in order that the reliability of the wall against failure modes must meet a desired level of safety. Sensitivity analysis is conducted to assess the effect of uncertainties in design parameters on the reliability of cantilever sheet pile walls. The analysis is performed by treating back fill soil properties, depth of the water table from the top of the sheet pile wall, yield strength of steel and section modulus of steel pile as random variables. Two limit states, viz., rotational and flexural failure of sheet pile wall are considered. The results using this approach are used to develop a set of reliability based design charts for different coefficients of variation of friction angle of the backfill (5%, 10% and 15%). System reliability considerations in terms of series and parallel systems are also studied.

Novel Algorithm for estimation of Swell Pressure of Fine Grained Soils Based on Diffuse Double Layer (DDL) Theory

Use of engineered landfills for the disposal of industrial wastes is currently a common practice. Bentonite is attracting a greater attention not only as capping and lining materials in landfills but also as buffer and backfill materials for repositories of high-level nuclear waste around the world. In the design of buffer and backfill materials, it is important to know the swelling pressures of compacted bentonite with different electrolyte solutions. The theoretical studies on swell pressure behaviour are all based on Diffuse Double Layer (DDL) theory. To establish a relation between the swell pressure and void ratio of the soil, it is necessary to calculate the mid-plane potential in the diffuse part of the interacting ionic double layers. The difficulty in these calculations is the elliptic integral involved in the relation between half space distance and mid plane potential. Several investigators circumvented this problem using indirect methods or by using cumbersome numerical techniques. In this work, a novel approach is proposed for theoretical estimations of swell pressures of fine-grained soil from the DDL theory. The proposed approach circumvents the complex computations in establishing the relationship between mid-plane potential and diffused plates’ distances in other words, between swell pressure and void ratio.

A rational approach to model the behavior of bonded soils

The paper presents a rational approach to model the behavior of bonded soils within the frame work of hardening plasticity. The approach is based on the premise that the resistance of bonded materials is a superposition of the two components of cement bond strength and soil frictional strength and that the deformation of the soil is associated with the frictional component of stresses just as in the case of a remoulded soil, the bonds offering additional resistance at any given strain level. This concept is similar to two stiffnesses acting in parallel for the same strain response. The proposed model considers the constitutive laws separately for the two components (bond and frictional) and adds the two to get the overall response. The unbonded soil component is described by the well known 'modified Cam clay' model. The response of the bond component is also described by a strain softening elasto-plastic model, considering the behavior to be elastic up to the yield surface and elasto-plastic beyond yield surface. To illustrate the capability of the proposed, model some laboratory test results of both compression and-extension shear tests are predicted. Despite the model being simple, several typical features of the behavior of bonded materials are well reproduced. The model parameters are well defined and easily determinable.