Water budgeting studies on the hatchery and nursery rearing practices for the common carp, Cyprinus carpio (Linnaeus, 1758)

Aquaculture systems are an integral element of rural development and therefore should be environment friendly as well as socially and economically designed. From the economic standpoint, one of the major constraints for the development of sustainable aquaculture includes externalities generated by competition in access to a limited resource. This study was conducted as an investigation into the water requirement for the hatchery and nursery production phases of common carp, Cyprinus carpio (Linnaeus, 1758) at the Maharashtra State Fish Seed Farm at Khopoli in Raigad Dist. of Maharashtra during the winter months from November to February. The water budgeting study involves the quantification of water used in every stage of production in hatchery and nursery systems and aimed at becoming a foundation for the minimization of water during production without affecting the yield; thereby conserving water and upholding the theme of sustainable aquaculture. The total water used in a single operation cycle was estimated to be 11,25,040 L [sic]. Out of the total water consumed, 4.74% water was used in the pre-operational management steps, 4.48% was consumed during breeding, 62.72% was consumed in the hatching phase, 21.50% was used for hatchery rearing and 6.56% was consumed during conditioning. In the nursery ponds, the water gain was primarily the regulated inflow coming through the irrigation channel. The total quantum of water used in the nursery rearing was 31,60,800 L [sic]. The initial filling and regulated inflow formed 42.60% and 57.40% respectively of water gain, while evaporation, seepage and discharge contributed 20.71%, 36.46% and 42.82% respectively to the water loss. The total water expended for the entire operation was 1,21,61,120 L [sic]. Water expense occurred to produce a single spawn in the hatchery system was calculated and found to be 0.56 L while the water expended to produce one fry was calculated as 4.86 L. The study fulfills the hydrological equation described by Winter (1981) and Boyd (1985). It also validates the water budget simulation model that can be used for forecasting water requirements for aquaculture ponds (Nath and Bolte, 1998).

Entwicklung eines Konzepts zum Lagermanagement mit Optimierungsansätzen auf Ebene eines neuen Regalbediengerätes

Die Grundidee hinter dem neuen Regalbediengerät ist die Minimierung der zu bewegenden Last durch die Verwendung einer seilbasierten Stewart-Gough-Plattform (SGP). Das klassische Regalbediengerät (RBG) wird dabei durch eine Plattform ersetzt, die an bis zu acht vorgespannten Seilen befestigt ist. Unterstützt wird diese Bauform durch eine abgestimmte Steuerungssoftware, die es ermöglicht die Vorteile des RBG optimal zu nutzen. Das hier mit Software vorgestellte Konzept regelt die Vorgehensweise zur Optimierung von Ein- und Auslagerungsaufträgen in einem Lagerregal, sowie die Optimierung der Fachbelegung in Zeiten ohne direkten Auftrag. Es beinhaltet dabei Mechanismen, die bestimmen wann Aufträge abgearbeitet werden, in welcher Reihenfolge und in welchen Kombinationen. Ziel ist es Ein- und Auslagerungsaufträge so zu kombinieren, dass möglichst effizient und schnell gearbeitet wird.

Temperature characteristics of the billet and the dies in a small batch forging production

The work reported herein is part of an on-going programme to develop a computer code which, given the geometrical, process and material parameters of the forging operation, is able to predict the die and the billet cooling/heating characteristics in forging production. The code has been experimentally validated earlier for a single forging cycle and is now validated for a small batch production. To facilitate a step-by-step development of the code, the billet deformation has so far been limited to its surface layers, a situation akin to coining. The code has been used here to study the effects of die preheat-temperature, machine speed and rate of deformation the cooling/heating of the billet and the dies over a small batch of 150 forgings. The study shows: that there is a pre-heat temperature at which the billet temperature changes little from one forging to the next; that beyond a particular number of forgings, the machine speed ceases to have any pronounced influence on the temperature characteristics of the billet; and that increasing the rate of deformation reduces the heat loss from the billet and gives the billet a stable temperature profile with respect to the number of forgings. The code, which is simple to use, is being extended to bulk-deformation problems. Given a practical range of possible machine, billet and process specifics, the code should be able to arrive at a combination of these parameters which will give the best thermal characteristics of the die-billet system. The code is also envisaged as being useful in the design of isothermal dies and processes.

Numerical and experimental study of the thermal behaviour of coining and upsetting processes

A numerical simulation technique has been employed to study the thermal behavior of hot-forging type forming processes. Experiments on the coining and upsetting of an aluminum billet were conducted to validate the numerical predictions. Typical forming conditions for both the coining and upsetting processes were then studied in detail. an electrical analogy scheme was used to determine the thermal contact resistance. This scheme can conviniently provide the interface characteristics for typical processing conditions, which normally involve high pressures and temperatures. A single forging cycle was first considered, and then a batch of twenty-five forgings was studied. Each forging cycle includes the billet mounting, ascent, loading, dwelling, unloading, descent, and billet removal stages. The temperature distribution in the first forging to be formed is found to be significantly different from that at the end of the batch. In industry, forging is essentially a batch operation. The influence of forming speed and reduction on thermal characteristics was investigated also. The variations that can occur in the process design by considering differences in temperature characteristics are discussed also.

Coking kinetics on the catalyst during alkylation of fcc off-gas with benzene to ethylbenzene

The production of ethylbenzene from the alkylation of dilute ethylene in fee off-gases with benzene has been commercialized in China over a newly developed catalyst composed of ZSM-5/ZSM-11 co-crystallized zeolite. The duration of an operation cycle of the commercial catalyst could be as long as 180 days. The conversion of ethylene could attain higher than 95%, while the amount of coke deposited on the catalyst was only about 10 wt.%. Thermogravimetry (TG) was used to study the coking behavior of the catalyst during the alkylation of fee off-gas with benzene to ethylbenzene. Based on effects of reaction time, reaction temperature, reactants and products on coking during the alkylation process, it is found that the coking rate during the alkylation procedure follows the order: ethylbenzene > ethylene > propylene > benzene for single component, and benzene-ethylene > benzene-propylene for bi-components under the same reaction condition. Furthermore, the coking kinetic equations for benzene-ethylene, benzene-propylene and ethylbenzene were established. (C) 2003 Elsevier B.V. All rights reserved.

The heliospheric Hale cycle over the last 300 years and its implications for a “lost” late 18th century solar cycle

A Hale cycle, one complete magnetic cycle of the Sun, spans two complete Schwabe cycles (also referred to as sunspot and, more generally, solar cycles). The approximately 22-year Hale cycle is seen in magnetic polarities of both sunspots and polar fields, as well as in the intensity of galactic cosmic rays reaching Earth, with odd- and even-numbered solar cycles displaying qualitatively different waveforms. Correct numbering of solar cycles also underpins empirical cycle-to-cycle relations which are used as first-order tests of stellar dynamo models. There has been much debate about whether the unusually long solar cycle 4 (SC4), spanning- 1784–1799, was actually two shorter solar cycles combined as a result of poor data coverage in the original Wolf sunspot number record. Indeed, the group sunspot number does show a small increase around 1794–1799 and there is evidence of an increase in the mean latitude of sunspots at this time, suggesting the existence of a cycle ‘‘4b’’. In this study, we use cosmogenic radionuclide data and associated reconstructions of the heliospheric magnetic field (HMF) to show that the Hale cycle has persisted over the last 300 years and that data prior to 1800 are more consistent with cycle 4 being a single long cycle (the ‘‘no SC4b’’ scenario). We also investigate the effect of cycle 4b on the HMF using an open solar flux (OSF) continuity model, in which the OSF source term is related to sunspot number and the OSF loss term is determined by the heliospheric current sheet tilt, assumed to be a simple function of solar cycle phase. The results are surprising; Without SC4b, the HMF shows two distinct peaks in the 1784–1799 interval, while the addition of SC4b removes the secondary peak, as the OSF loss term acts in opposition to the later rise in sunspot number. The timing and magnitude of the main SC4 HMF peak is also significantly changed by the addition of SC4b. These results are compared with the cosmogenic isotope reconstructions of HMF and historical aurora records. These data marginally favour the existence of SC4b (the ‘‘SC4b’’ scenario), though the result is less certain than that based on the persistence of the Hale cycle. Thus while the current uncertainties in the observations preclude any definitive conclusions, the data favour the ‘‘no SC4b’’ scenario. Future improvements to cosmogenic isotope reconstructions of the HMF, through either improved modelling or additional ice cores from well-separated geographic locations, may enable questions of the existence of SC4b and the phase of Hale cycle prior to the Maunder minimum to be settled conclusively.

Influence of the number of load cycles to obtain the stiffness properties of angico preto (Anadenanthera macrocarpa) wood specie

The tests used to obtain the stiffness properties of wood are made with two loading cycles, as defined by the Brazilian standard ABNT NBR 7190 (Design of Timber Structures). However, the possibility of reducing the number of cycles allows decrease the operating time of the machine, resulting in reduced spending on electricity used during the tests. This research aimed to investigate, with the aid of the analysis of variance (ANOVA), the influence of the use of three load cycles to obtain the modulus of elasticity in compression parallel to grain (Ec0), in tensile parallel to the grain (Et0), in bending (Em) and in compression perpendicular to the grain (Ec90) of Angico Preto (Anadenanthera macrocarpa) wood specie. For the number of cycles and stiffness were manufactured 12 samples, totaling 144 specimens. The results of the ANOVA revealed statistical equivalence between the stiffness properties for both load cycle numbers evaluated, indicating that it is possible to carry out the tests with a single charge cycle, allowing savings in time and energy in the operation of the equipment.

Long-term followup results of 1 cycle of adjuvant bleomycin, etoposide and cisplatin chemotherapy for high risk clinical stage I nonseminomatous germ cell tumors of the testis

PURPOSE: We evaluated the long-term outcome after 1 cycle of adjuvant modified bleomycin, etoposide and cisplatin chemotherapy in patients who underwent orchiectomy for high risk clinical stage I nonseminomatous germ cell tumor of the testis. MATERIALS AND METHODS: Between 1995 and 1999 a consecutive series of 44 patients underwent orchiectomy for clinical stage I nonseminomatous germ cell tumor of the testis, followed by a single postoperative cycle of adjuvant modified bleomycin, etoposide and cisplatin for vascular or lymphatic tumor invasion, and/or a predominance (50% or greater) of embryonal carcinoma. RESULTS: Four of the 44 patients were excluded from analysis. Of the patients 35 had no evidence of disease at a median followup of 99 months (range 60 to 134). One patient with progression after 13 months showed complete remission after 3 cycles of salvage bleomycin, etoposide and cisplatin chemotherapy but he died of pneumonia 4 weeks after the third course. Two patients underwent orchiectomy for contralateral testis cancer at 18 and 42 months, respectively, followed by an additional 3 cycles of adjuvant chemotherapy. They remained relapse-free for 4 and 92 months, respectively. The former patient was lost to followup after 4 months. Two other patients were disease-free at 10 and 31 months, respectively, and were lost to followup thereafter. Late side effects were tinnitus in 3 patients and involuntary childlessness in 3, of whom 2 had cryptorchidism of the contralateral testis. Nine patients fathered children. CONCLUSIONS: One cycle of bleomycin, etoposide and cisplatin effectively decreases the risk of relapse in patients with high risk stage I nonseminomatous germ cell tumor of the testis. It has minimal side effects and can be a valuable alternative to retroperitoneal lymph node dissection.

A self-timed multipurpose delay sensor for field programmable gate arrays (FPGAs)

This paper presents a novel self-timed multi-purpose sensor especially conceived for Field Programmable Gate Arrays (FPGAs). The aim of the sensor is to measure performance variations during the life-cycle of the device, such as process variability, critical path timing and temperature variations. The proposed topology, through the use of both combinational and sequential FPGA elements, amplifies the time of a signal traversing a delay chain to produce a pulse whose width is the sensor’s measurement. The sensor is fully self-timed, avoiding the need for clock distribution networks and eliminating the limitations imposed by the system clock. One single off- or on-chip time-to-digital converter is able to perform digitization of several sensors in a single operation. These features allow for a simplified approach for designers wanting to intertwine a multi-purpose sensor network with their application logic. Employed as a temperature sensor, it has been measured to have an error of ±0.67 °C, over the range of 20–100 °C, employing 20 logic elements with a 2-point calibration.

Case study: Dragline swing to dump automation

Dragline Swing to Dump Automation By Peter Corke, CSIRO Manufacturing Technology/CRC for Mining Technology and Equipment (CMTE) Peter Corke presented a case study of a project to automate the dragline swing to dump operation. The project is funded by ACARP, BHP Coal, Pacific Coal and the CMTE and is being carried out on a dragline at Pacific Coal's Meandu mine near Brisbane. Corke began by highlighting that the minerals industry makes extensive use of large, mechanised machines. However, unlike other industries, mining has not adopted automation and most machines are controlled by human operators on board the machine itself. Choosing an automation target The dragline automation was chosen because: ò draglines are one of the biggest capital assets in a mine; ò performance between operators vary significantly, so improved capital utilisation is possible; ò the dragline is often the bottleneck in production; ò a large part of the operation cycle is spent swinging from dig to dump; and ò it is technically feasible. There has been a history of drag line automation projects, none with great success.

Real-World Extensions To Scheduling Algorithms Based On Lagrangian Relaxation

Recently, efficient scheduling algorithms based on Lagrangian relaxation have been proposed for scheduling parallel machine systems and job shops. In this article, we develop real-world extensions to these scheduling methods. In the first part of the paper, we consider the problem of scheduling single operation jobs on parallel identical machines and extend the methodology to handle multiple classes of jobs, taking into account setup times and setup costs, The proposed methodology uses Lagrangian relaxation and simulated annealing in a hybrid framework, In the second part of the paper, we consider a Lagrangian relaxation based method for scheduling job shops and extend it to obtain a scheduling methodology for a real-world flexible manufacturing system with centralized material handling.

Discovering behavioural interfaces for overloaded web services

The growth of APIs and Web services on the Internet, especially through larger enterprise systems increasingly being leveraged for Cloud and software-as-a-service opportuni- ties, poses challenges to improving the efficiency of integration with these services. Interfaces of enterprise systems are typically larger, more complex and overloaded, with single operation having multiple data entities and parameter sets, supporting varying requests, and reflecting versioning across different system releases, compared to fine-grained operations of contemporary interfaces. We propose a technique to support the refactoring of service interfaces by deriving business entities and their relationships. In this paper, we focus on the behavioural aspects of service interfaces, aiming to discover the sequential dependencies of operations (otherwise known as protocol extraction) based on the entities and relationships derived. Specifically, we propose heuristics according to these relationships, and in turn, deriving permissible orders in which operations are invoked. As a result of this, service operations can be refactored on business entity CRUD lines, with explicit behavioural protocols as part of an interface definition. This supports flexible service discovery, composition and integration. A prototypical implementation and analysis of existing Web services, including those of commercial logistic systems (Fedex), are used to validate the algorithms proposed through the paper.

Hemiorchidectomy leads to dramatic and immediate alterations in pituitary follicle-stimulating hormone secretion and the functional activity of the remaining testis in the adult male bonnet monkey (Macaca radiata)

The aim of the present study was to examine the effect of hemiorchidectomy (HO) on serum FSH, LH, testosterone (T), and inhibin (INH) concentrations as well as on the testicular volume (TV) and on changes in the kinetics of germ cell turnovers in the remaining testis of adult male bonnet monkeys. Blood samples collected at 2200 h at various times before and after HO and testicular biopsies obtained at different periods were subjected to hormone analysis and DNA flow cytometry. Though serum T levels were lowered (p < 0.05) at 12 h after HO, T levels rapidly returned to intact control concentrations by Day 5. While serum LH remained unaltered, serum FSH increased markedly within 2 days of HO and remained significantly (p < 0.05) elevated over the next 90 days. Though serum INH showed a significant decrease (p < 0.05) by 15 min of HO, it returned to approximately 80% of intact levels within one week. The TV of the remaining testis showed maximal increment by Day 30 (p < 0.05) of HO. DNA flow cytometric analysis 24 days after HO showed increases (p < 0.05) in spermatogonia (2C) and primary spermatocytes (4C). These cell types by Day 45 had transformed to round (1C) and elongate (HC) (by 38%, p < 0.001) spermatids. Overall spermatogenesis (conversion of 2C to 1C and HC) showed significant enhancement at Days 110 and 175, suggesting that the spurt in spermatogenic activity is not confined to a single spermatogenic cycle.

Combinatorial logic synthesis using technology directed decomposition

The aim of logic synthesis is to produce circuits which satisfy the given boolean function while meeting timing constraints and requiring the minimum silicon area. Logic synthesis involves two steps namely logic decomposition and technology mapping. Existing methods treat the two as separate operation. The traditional approach is to minimize the number of literals without considering the target technology during the decomposition phase. The decomposed expressions are then mapped on to the target technology to optimize the area, Timing optimization is carried out subsequently, A new approach which treats logic decomposition and technology maping as a single operation is presented. The logic decomposition is based on the parameters of the target technology. The area and timing optimization is carried out during logic decomposition phase itself. Results using MCNC circuits are presented to show that this method produces circuits which are 38% faster while requiring 14% increase in area.

Use of pseudoephedrine as a practical chiral auxiliary for asymmetric synthesis

The use of pseudoephedrine as a practical chiral auxiliary for asymmetric synthesis is describe. Both enantiomers of pseudoephedrine are inexpensive commodity chemicals and can be N-acylated in high yields to form tertiary amides. In the presence of lithium chloride, the enolates of the corresponding pseudoephedrine amides undergo highly diastereoselective a1kylations with a wide range of alkyl halides to afford α-substituted products in high yields. These products can then be transformed in a single operation into highly enantiomerically enriched carboxylic acids, alcohols, and aldehydes. Lithium amidotrihydroborate (LAB) is shown to be a powerful reductant for the selective reduction of tertiary amides in general and pseudoephedrine amides in particular to form primary alcohols.