Acid volatile sulfide and simultaneously extracted metals in the sediment cores of the Pearl River Estuary, South China

The acid-volatile sulfide (AVS), simultaneously extracted metals (SEM), total metals, and chemical partitioning in the sediment cores of the Pearl River Estuary (PRE) were studied. The concentrations of total metals, AVS, and SEM in the sediment cores were generally low in the river outlet area, increased along the seaward direction, and decreased again at the seaward boundary of the estuary. The amounts of AVS were generally greater in deeper sediments than in surface sediments. SEM/AVS was > 1 in the surface sediments and in the river outlet cores. The ratio was < 1 in the sediments down the profiles, suggesting that AVS might play a major role in binding heavy metals in the deep sediments of the PRE. The SEM may contain different chemical forms of trace metals in the sediments, depending on the metal reaction with 1 M cold HCl in the AVS procedure compared with the results of the sequential chemical extraction. The SEM/AVS ratio prediction may overestimate trace metal availability even in the sediments with high AVS concentrations. (c) 2004 Elsevier Inc. All rights reserved.

Approccio SEM-AVS (Simultaneously Extracted Metals-Acid Volatile Sulfides) per la valutazione del rischio ambientale dei metalli nei sedimenti della Pialassa Baiona

La Pialassa Baiona è una laguna sottoposta a diversi vincoli normativi, visto il suo inquadramento tra le aree SIC e ZPS, e soggetta a diverse sorgenti di disturbo antropico, più intense negli anni ‘50-‘70. Questa tesi si propone lo scopo di valutare il rischio associato ai metalli bivalenti presenti nei sedimenti della Pialassa Baiona attraverso tre approcci: il primo riguarda la determinazione della frazione biodisponibile dei metalli presenti nei sedimenti attraverso la determinazione dei solfuri acidi volatili (AVS) e dei metalli simultaneamente estraibili (SEM), nonché la valutazione della potenziale tossicità dei sedimenti attraverso la valutazione del rapporto molare SEM/AVS, il secondo approccio considera invece il contenuto pseudo totale dei metalli bivalenti (Cd, Cu, Ni, Pb e Zn) e il loro confronto sia con i valori tipici di fondo naturale del Mar Adriatico che con i valori guida di riferimento internazionale (Threshold Effect Level, TEL e Probable Effect Level, PEL) al fine di valutare lo stato di qualità dei sedimenti della zona d’indagine. Il terzo approccio considera l’influenza del gradiente naturale terra-mare tipico delle zone di transizione e del gradiente antropico legato alla vicinanza dell’area industriale alla Pialassa Baiona, sulla distribuzione spaziale dei metalli oggetto di questo studio. I risultati ottenuti evidenziano che l’area più prossima alla zona industriale e al contempo più lontana dall’effetto del ricambio delle acque e di dilavamento ad opera del mare, è risultata quella con livelli significativamente più elevati per la maggior parte dei metalli analizzati. Questo permette di ipotizzare un’influenza diretta delle sorgenti di inquinanti, ma anche un effetto dispersivo della circolazione. Gli AVS hanno invece evidenziato un gradiente terra-mare; ciò comporta che nelle zone più prossime all’influenza del mare si sono riscontrate concentrazioni minori di AVS. La valutazione della potenziale tossicità dei metalli in termini di rapporto SEM/AVS non ha evidenziato la presenza di siti a rischio per il biota acquatico, se non per un unico sito prossimo all’area industriale.

A critical comparison of different approaches to sediment-quality assessments in the Santos estuarine system in Brazil

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Quantificação e avaliação da biodisponibilidade de metais em sedimentos na Baía da Ribeira RJ

A toxicidade dos metais em ambientes aquáticos está relacionada à sua biodisponibilidade e esta, por sua vez, pode ser influenciada por diversos fatores. As características do sedimento fazem dele um importante compartimento para avaliação do nível de contaminação no ambiente aquático. A presente pesquisa teve por objetivo quantificar e avaliar a biodisponibilidade de metais em sedimentos da baía da Ribeira. Nessa região, encontram-se os bairros mais populosos de Angra dos Reis RJ. Essa baía está localizada na parte nordeste da baía da Ilha Grande, que consiste de um espaço pesqueiro, turístico e de importante valor econômico e industrial. Foram coletados 12 sedimentos na baía da Ribeira e determinados os teores dos metais Al, Cu, Cd , Cr, Fe, Mn, Ni, Pb e Zn, através da extração com água régia (protocolo BCR-701), e o potencial de toxicidade dos metais Cd, Cu, Ni, Pb e Zn pelo método de extração dos sulfetos voláteis em meio ácido e quantificação dos metais extraídos simultaneamente (em inglês Acid Volatile Sulfide and Simultaneously Extracted Metal, AVS/SEM). Também foram efetuadas medidas de pH, potencial redox (Eh), carbono orgânico, fósforo total e granulometria. Através desses dados, foi possível estudar correlações entre essas variáveis. As concentrações de cada metal são similares nas diferentes localizações dos sedimentos e não apresentam significativas diferenças com relação a estudos reportados para a área, com exceção do Pb que apresentou a mais alta concentração já reportada. Os valores de SEM/AVS (entre 0,02 e 0,2) menores que 1, indicam que há quantidade de sulfetos suficiente para o aprisionamento dos metais investigados. As correlações obtidas através da Análise dos Componentes Principais demonstram relação direta entre as concentrações da maioria dos metais extraídos por água-régia (Ni, Fe, Cr, Cu, Zn); entre os metais Mn, Pb, Al e o fósforo total; entre os teores de matéria orgânica, carbono orgânico total, fósforo total com as frações finas de silte e argila com o Eh. Os resultados sugerem que a região não sofre influência significativa de fontes antrópicas em relação a metais e que, segundo o AVS/SEM, esses se encontram pouco disponíveis para o ambiente e, portanto, apresentam baixo potencial tóxico

Policy of routine titanium miniplate removal after maxillofacial trauma

PURPOSE: The literature shows that hardware removal rates after the fixation of maxillofacial fractures with miniplates are not insignificant. The aim of the present survey was to clarify the policies of Finnish oral and maxillofacial consultants for the removal of titanium miniplates after the treatment of facial fractures in adults. Additional aims were to clarify the factors influencing plate removal policy in general, and the reasons for routine plate removal in particular. MATERIALS AND METHODS: Twenty-six consultant oral and maxillofacial surgeons responded to a questionnaire about miniplate removal policy after treating 5 types of simple, noncomminuted fractures. RESULTS: Overall, routine plate removal was uncommon. However, 12 consultants (46.2%) routinely removed the plate after treating mandibular angle fractures, and simultaneously extracted the third molar because of an increased risk of infection. Most respondents (88.5%) stated that clinical experience guided their plate-removal policy. A policy of routine plate removal was most infrequent among the consultants who had the most experience. CONCLUSIONS: The literature provides no definitive answer to the question of whether routine removal of miniplates could or should be indicated, and in what situations. Considering the fairly significant frequency of plate-related complications in general and infection-related complications in particular, long-term follow-up after treatment is indicated.

Measurement of the tt̅W and tt̅Z Cross Sections using Proton-Proton Collisions at √s = 8 TeV with the ATLAS Detector

A measurement of the production cross sections of top quark pairs in association with a W or Z boson is presented. The measurement uses 20.3 fb−1 of data from proton-proton collisions at √s = 8 TeV collected by the ATLAS detector at the Large Hadron Collider. Four different final states are considered: two opposite-sign leptons, two same-sign leptons, three leptons, and four leptons. The t t̅ W and t t̅ Z cross sections are simultaneously extracted using a maximum likelihood fit over all the final states. The t t̅ Z cross section is measured to be 176+58−52 fb, corresponding to a signal significance of 4.2σ. The t t̅ W cross section is measured to be 369+100−91 fb, corresponding to a signal significance of 5.0σ. The results are consistent with next-to-leading-order calculations for the tt̅W and tt̅Z processes.

Heavy Metals Extracted by DTPA and Organic Acids from Soil Amended with Urban or Industrial Residues

Understanding soil responses to the application of urban or industrial residues is necessary. In the current experiment, both sources of residues were applied to the soil surface of a Hapludox soil for 8 years. The four residues studied were biodigested and centrifuged sewage sludge (LB and LC, respectively), steel slag from the metallurgic industry (E), and limed mud from the pulp and cellulose industry (LCal). The residues were applied at 0, 2, 4, and 8 Mg ha(-1) four times from 2002 to 2010 when soybean was cultivated in the summer and lopsided oat and sorghum were cultivated during the winter. The contents of heavy metals were evaluated with diethylenetriaminepentaacetic acid (DTPA) and organic acids. The LB was the residue that increased the contents of soil micronutrients and heavy metals to their greatest levels, although within limits that impair the risks of environmental contamination.

A critical examination of the paradox of strength and ductility in ultrafine-grained metals

The paradox of strength and ductility is now well established and denotes the difficulty of simultaneously achieving both high strength and high ductility. This paradox was critically examined using a cast Al-7% Si alloy processed by high-pressure torsion (HPT) for up to 10 turns at a temperature of either 298 or 445 K. This processing reduces the grain size to a minimum of similar to 0.4 mu m and also decreases the average size of the Si particles. The results show that samples processed to high numbers of HPT turns exhibit both high strength and high ductility when tested at relatively low strain rates and the strain rate sensitivity under these conditions is similar to 0.14 which suggests that flow occurs by some limited grain boundary sliding and crystallographic slip. The results are also displayed on the traditional diagram for strength and ductility and they demonstrate the potential for achieving high strength and high ductility by increasing the number of turns in HPT.

Silicide formation and the interaction of metals with polycrystalline Si

The main factors affecting solid-phase Si-metal interactions are reported in this work. The influence of the orientation of the Si substrates and the presence of impurities in metal films and at the Si-metal interface on the formation of nickel and chromium silicides have been demonstrated. We have observed that the formation and kinetic rate of growth of nickel silicides is strongly dependent on the orientation and crystallinity of the Si substrates; a fact which, up to date, has never been seriously investigated in silicide formation. Impurity contaminations in the Cr film and at the Si-Cr interface are the most dominant influencing factors in the formation and kinetic rate of growth of CrSi₂. The potentiality and use of silicides as a diffusion barrier in metallization on silicon devices were also investigated.

Two phases, Ni₂Si and NiSi, form simultaneously in two distinct sublayers in the reaction of Ni with amorphous Si, while only the former phase was observed on other substrates. On (111) oriented Si substrates the growth rate is about 2 to 3 times less than that on <100> or polycrystalline Si. Transmission electron micrographs establish-·that silicide layers grown on different substrates have different microcrystalline structures. The concept of grain-boundary diffusion is speculated to be an important factor in silicide formation.

The composition and kinetic rate of CrSi₂ formation are not influenced by the underlying Si substrate. While the orientation of the Si substrate does not affect the formation of CrSi₂ , the purity of the Cr film and the state of Si-Cr interface become the predominant factors in the reaction process. With an interposed layer of Pd₂Si between the Cr film and the Si substrate, CrSi₂ starts to form at a much lower temperature (400°C) relative to the Si-Cr system. However, the growth rate of CrSi₂ is observed to be independent of the thickness of the Pd2Si layer. For both Si-Cr and Si-Pd₂Si-Cr samples, the growth rate is linear with time with an activation energy of 1.7 ± 0.1 ev.

A tracer technique using radioactive ³¹Si (T_1/2 = 2.26 h) was used to study the formation of CrSi₂ on Pd₂Si. It is established from this experiment that the growth of CrSi₂ takes place partly by transport of Si directly from the Si substrate and partly by breaking Pd₂Si bonds, making free Si atoms available for the growth process.

The role of CrSi₂ in Pd-Al metallization on Si was studied. It is established that a thin CrSi₂ layer can be used as a diffusion barrier to prevent Al from interacting with Pd₂Si in the Pd-Al metallization on Si.

As a generalization of what has been observed for polycrystalline-Si-Al interaction, the reactions between polycrystalline Si (poly Si) and other metals were studied. The metals investigated include Ni, Cr, Pd, Ag and Au. For Ni, Cr and Pd, annealing results in silicide formation, at temperatures similar to those observed on single crystal Si substrates. For Al, Ag and Au, which form simple eutectics with Si annealing results in erosion of the poly Si layer and growth of Si crystallites in the metal films.

Backscattering spectrometry with 2.0 and 2.3 MeV ⁴He ions was the main analytical tool used in all our investigations. Other experimental techniques include the Read camera glancing angle x-ray diffraction, scanning electron, optical and transmission electron microscopy. Details of these analytical techniques are given in Chapter II.

Band alignment between Ta2O5 and metals for resistive random access memory electrodes engineering

Band alignment of resistive random access memory (RRAM) switching material Ta2O5 and different metal electrode materials was examined using high-resolution X-ray photoelectron spectroscopy. Schottky and hole barrier heights at the interface between electrode and Ta2O 5 were obtained, where the electrodes consist of materials with low to high work function (Φ m, v a c from 4.06 to 5.93 eV). Effective metal work functions were extracted to study the Fermi level pinning effect and to discuss the dominant conduction mechanism. An accurate band alignment between electrodes and Ta2O5 is obtained and can be used for RRAM electrode engineering and conduction mechanism study. © 2013 American Institute of Physics.

Analysis of norditerpenoid alkaloids extracted from Aconitum sinomantanum Nakai by electrospray ionization tandem mass spectrometry

Electrospray ionization mass spectrometry (ESI-MS) was applied simultaneously in determining norditerpenoid alkaloids from the roots of Aconitum sinomantanum Nakai ( RAS) based on molecular mass information. The tandem mass spectra (ESI-MSn) provided the alkaloidal structural information, through which the existence of these alkaloids was further confirmed. Accordingly, six known norditerpenoid alkaloids were simultaneously determined on the basis of their ESI-MSn spectra. Furthermore, based on the diagnostic fragmentation pathways of alkaloidal MSn, a rapid method for direct detection and characterization of alkaloids from an ethanolic extract of RAS was described.

Optimization of the electrodialytic phosphorus recovery from sewage sludge ash

Phosphorus (P) is becoming a scarce element due to the decreasing availability of primary sources. Therefore, recover P from secondary sources, e.g. waste streams, have become extremely important. Sewage sludge ash (SSA) is a reliable secondary source of P. The use of SSAs as a direct fertilizer has very restricted legislation due to the presence of inorganic contaminants. Furthermore, the P present in SSAs is not in a plant-available form. The electrodialytic (ED) process is one of the methods under development to recover P and simultaneously remove heavy metals. The present work aimed to optimize the P recovery through a 2 compartment electrodialytic cell. The research was divided in three independent phases. In the first phase, ED experiments were carried out for two SSAs from different seasons, varying the duration of the ED process (2, 4, 6 and 9 days). During the ED treatment the SSA was suspended in distilled water in the anolyte, which was separated from the catholyte by a cation exchange membrane. From both ashes 90% of P was successfully extracted after 6 days of treatment. Regarding the heavy metals removal, one of the SSAs had a better removal than the other. Therefore, it was possible to conclude that SSAs from different seasons can be submitted to ED process under the same parameters. In the second phase, the two SSAs were exposed to humidity and air prior to ED, in order to carbonate them. Although this procedure was not successful, ED experiments were carried out varying the duration of the treatment (2 and 6 days) and the period of air exposure that SSAs were submitted to (7, 14 and 30 days). After 6 days of treatment and 30 days of air exposure, 90% of phosphorus was successfully extracted from both ashes. No differences were identified between carbonated and non-carbonated SSAs. Thus, SSAs that were exposed to the air and humidity, e.g. SSAs stored for 30 days in an open deposit, can be treated under the same parameters as the SSAs directly collected from the incineration process. In the third phase, ED experiments were carried out during 6 days varying the stirring time (0, 1, 2 and 4 h/day) in order to investigate if energy can be saved on the stirring process. After 6 days of treatment and 4 h/day stirring, 80% and 90% of P was successfully extracted from SSA-A and SSA-B, respectively. This value is very similar to the one obtained for 6 days of treatment stirring 24 h/day.

Availability of heavy metals for uptake by Salix viminalis on a moderately contaminated dredged sediment disposal site

Extractability of Cd. Cr, Cu, Ni, Pb, and Zn in a dredged sediment disposal site was assessed using single extraction Procedures (H2O; 0.01 M CaCl2; 1 M NH4OAc NH4OAc-EDTA. CaCl2-TEA-DTPA). Only Cd and Zn were Found to exceed statutory threshold values for total content. The field was planted with Salix viminalis "Orm" and accumulation of heavy metals in bark, leaves, roots, and wood was evaluated at seven sampling locations along an observed gradient in texture and pollution. Biomass production was high, ranging from 13.2 to 17.8 t ha(1) y(1) dry weight. Metal accumulation in aboveground Plant parts Was low. amounting to the following annually extracted mass or metals per ha: 5034 g Zn, 83 g Cd. W g Cu. 83 g Pb, 12 g Ni and 6 g Cr. The use of accumulating clones and the use of soil amendments might enhance extraction efficiency in future research. (C) 2005 Elsevier Ltd. All rights reserved.

Evaluation of some metals in Brazilian coffees cultivated during the process of conversion from conventional to organic agriculture

The aim of this study was to evaluate the presence of nutrients and toxic elements in coffees cultivated during the process of conversion, on organic agriculture, in southwest Bahia, Brazil. Levels of the nutrients and toxic elements were determined in samples of soils and coffee tissues from two transitional organic farms by atomic absorption spectrometry (FAAS). The metals in soil samples were extracted by Mehlich1 and USEPA-3050 procedures. Coffee samples from both farms presented relatively high levels of Cd, Zn and Cu (0.75,45.4 and 14.9 mu g g(-1). respectively), but were still below the limits specified by the Brazilian Food Legislation. The application of statistical methods showed that this finding can be attributed to the addition of high amounts of organic matter during the flowering tree period which can act on the bioavailability of metal ions in soils. (C) 2009 Elsevier Ltd. All rights reserved.

Peat humic substances enriched with nutrients for agricultural applications: Competition between nutrients and non-essential metals present in tropical soils

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)