Mechanism study of femtosecond laser induced selective metallization (FLISM) on glass surfaces

We investigate the mechanism of selective metallization on glass surfaces with the assistance of femtosecond laser irradiation followed by electroless plating. Irradiation of femtosecond laser makes it possible to selectively deposit copper microstructures in the irradiated area on glass surfaces coated with silver nitrate films. The energy-dispersive X-ray (EDX) analyses reveal that silver atoms are produced on the surface of grooves formed by laser ablation, which serve as catalysis seeds for subsequent electroless copper plating. (C) 2008 Elsevier B.V. All rights reserved.

Selective metallization on insulator surfaces with femtosecond laser pulses

We report selective metallization on surfaces of insulators ( glass slides and lithium niobate crystal) based on femtosecond laser modification combined with electroless plating. The process is mainly composed of four steps: (1) formation of silver nitrate thin films on the surfaces of glass or crystal substrates; (2) generation of silver particles in the irradiated area by femtosecond laser direct writing; (3) removal of unirradiated silver nitrate films; and (4) selective electroless plating in the modified area. We discuss the mechanism of selective metallization on the insulators. Moreover, we investigate the electrical and adhesive properties of the copper microstructures patterned on the insulator surfaces, showing great potential of integrating electrical functions into lab-on-a-chip devices. (C) 2007 Optical Society of America.

Fabrication of an integrated Raman sensor by selective surface metallization using a femtosecond laser oscillator

We demonstrate that a Raman sensor integrated with a micro-heater, a microfluidic chamber, and a surface-enhanced Raman scattering (SERS) substrate can be fabricated in a glass chip by femtosecond laser micromachining. The micro-heater and the SERS substrate are fabricated by selective metallization on the glass surface using a femtosecond laser oscillator, whereas the microfluidic chamber embedded in the glass sample is fabricated by femtosecond laser ablation using a femtosecond laser amplifier. We believed that this new strategy for fabricating multifunctional integrated microchips has great potential application for lab-on-a-chips. (C) 2008 Elsevier B.V. All rights reserved.

Structural insights into the allosteric activation mechanism of cGMP-dependent protein kinase I

Cyclic GMP-dependent protein kinase (PKG) is a key transducer in the NO-cGMP signaling pathway. In this line, PKG has been considered an important drug target for treating hypertensive cardiovascular and pulmonary diseases. However, the investigation of PKG’s allosteric activation mechanism has been hampered by a lack of structural information. One of the fundamental questions on the cGMP-dependent activation of PKG is how the enzyme can distinguish cGMP over cAMP and selectively respond to cGMP. To ensure proper signaling, PKG must have developed unique features to ensure its activation upon the right activation signal. In this thesis, the cGMP-selective activation mechanism of PKG was studied through determining crystal structures of three truncated constructs of the regulatory domain [CNB-A (92-227), CNB-B (271-369), and CNB-A/B (92-351)] of PKG Iβ in the absence or presence of cyclic nucleotides. Herein, two individual CNB domain structures with biochemical data revealed that the C-terminal CNB domain (CNB-B) is responsible for cGMP selectivity, while the N-terminal CNB-domain (CNB-A) has a higher binding affinity for both cGMP and cAMP without showing any selectivity. Based on these crystal structures, mutagenesis studies were performed in which the critical residues for cyclic nucleotide selectivity and activation were identified. Furthermore, we discovered that the conformational changes of the C-terminal helix of the CNB-B that bridges between the regulatory and catalytic domains including the hydrophobic capping interaction are crucial for PKG activation. In addition, to observe the global conformation of the activated R-domain, I solved a co-crystal structure of the CNB-A/B with cGMP. Although a monomeric construct was crystallized, the structure displays a dimer. Strikingly, the CNB-A domain and its bound cGMP provide a key interface for this dimeric interaction. Using small angle X-ray scattering (SAXS), the existence of the cGMP-mediated dimeric interface within the CNB domains was confirmed. Furthermore, measuring cGMP-binding affinities (EC50) of the dimeric interface mutants as well as determining activation constants (Ka) revealed that the interface formation is important for PKG activation. To conclude, this thesis study provides a new mechanistic insight in PKG activation along with a newly found interface that can be targeted for designing PKG-specific activity modulators.

Parvovirus B19 uptake is a highly selective process controlled by VP1u, a novel determinant of viral tropism

The VP1 unique region (VP1u) of human parvovirus B19 (B19V) is the immunodominant part of the viral capsid. Originally inaccessible, the VP1u becomes exposed upon primary attachment to the globoside receptor. To study the function of the exposed VP1u in B19V uptake, we expressed this region as a recombinant protein. Here, we report that purified recombinant VP1u binds and is internalized in UT7/Epo cells. By means of truncations and specific antibodies, we identified the most N-terminal amino acid residues of VP1u as the essential region for binding and internalization. Furthermore, the recombinant VP1u was able to block B19V uptake, suggesting that the protein and the virus undertake the same internalization pathway. Assays with different erythroid and nonerythroid cell lines showed that the N-terminal VP1u binding was restricted to a few cell lines of the erythroid lineage, which were also the only cells that allowed B19V internalization and infection. These results together indicate that the N-terminal region of VP1u is responsible for the internalization of the virus and that the interacting receptor is restricted to B19V-susceptible cells. The highly selective uptake mechanism represents a novel determinant of the tropism and pathogenesis of B19V.

In-situ examination of the selective etching of an alkanethiol monolayer covered Au{111} surface

An examination of the selective etching mechanism of a 1-alkanethiol self-assembled monolayer (SAM) covered Au{111} surface using in-situ atomic force microscopy (AFM) and molecular resolution scanning tunnelling microscopy (STM) is presented. The monolayer self-assembles on a smooth Au{111} surface and typically contains nanoscale non-uniformities such as pinholes, domain boundaries and monatomic depressions. During etching in a ferri/ferrocyanide water-based etchant, selective and preferential etching occurs at SAM covered Au(111) terrace and step edges where a lower SAM packing density is observed, resulting in triangular islands being relieved. The triangular islands are commensurate with the Au(111) lattice with their long edges parallel to its [11-0] direction. Thus, SAM etching is selective and preferential attack is localized to defects and step edges at sites of high molecular density contrast.

陆地棉组织培养及转化研究

1．以MS无机盐+B 5有机成分为基本培养基，附加2，4-D，KT，ZT等激素，以农艺性状良好，抗枯萎病的棉花品种“冀492”为材料，建立了愈伤组织诱导，体细胞胚胎发生和植株再生体系． 2．实验结果表明，2，4-D是诱导愈伤组织产生的促进因子，效果明显好于其它生长素类物质，但是随着培养基中2，4-D浓度的升高，愈伤组织状态也会变差，褐化严重，而且，附加O.lppm 2，4-D，O.lppm K T的培养基是较为合适的培养基．IAA，NAA对愈伤组织的诱导不十分理想，此外，愈伤组织的产生还同外植体，基因型和一些物理条件有关， 胚性愈伤组织的产生，需不断调节培养基中激素浓度，逐步降低2，4 -D浓度，并添加低浓度ZT，胚状体要在去除2，4-D的培养基上才能产生．虽然，2，4-D对于胚性愈伤组织的诱导是必须的，但是却抑制胚状体的发育． 3．培养基中硝态氮和氨态氮比例，激素浓度和种类，活性炭的添加，对于胚状体的萌发和成熟有重要影响，硝酸钾加倍，硝酸铵减半，并附加低浓度ABA和活性炭是胚状体诱导和成苗（去除ABA）的适宜培养基，而附加0.2ppm N A A，0.2ppm ZT和活性炭的M S2培养基是胚状体成熟的适宜培养基．通过对胚性愈伤组织的干燥处理，培养基中低浓度ABA和活性炭的添加，比较有效地抑制了畸形胚的产生，大大地提高了正常胚的比例． 4．对陆地棉“冀4 9 2”的下胚轴和子叶利用含Bt抗虫基因的根农杆菌(AgrobacterIIm tumefrens)进行了遗传转化研究，在筛选培养基上获得了大量生长旺盛的阳性愈伤组织，葡糖酸苷检测结果表明，大部分愈伤组织均有G us基因的表达． 5．通过花粉管通道法，进行了将含有Bt抗虫基因DNA的大肠杆菌质粒导入陆地棉“冀492”的实验，并收获了近1 0，000粒种子，为从大量种子中筛选出抗性种质材料，建立了卡那霉素田间初步筛选法． 6．利用活体压片和石蜡切片技术对体细胞胚胎发生过程和胚状体起源进行了观察，发现胚状体发生主要是通过类合子途径进行的，胚状体可能起源于单细胞． 7．通过对相同培养基上的非胚性愈伤组织，胚性愈伤组织和不同时期胚状体的可溶性蛋白SDS - PAGE电泳分析，发现16KD和50K D蛋白特异性地存在于胚性愈伤和各期胚状体中，该蛋白可作为胚性愈伤组织的筛选标记．对不同发育时期的愈伤组织进行了同工酶和可溶性蛋白的IE F/SD S-PA G E双向电泳分析，结果表明，不同发育时期的愈伤组织同工酶酶谱和可溶性蛋白电泳图谱之间具有较大的差别，分化前期的胚性愈伤组织酶的活性强，种类多，并且有新的蛋白斑点的出现，这些都可能与体细胞胚胎发生相关．

Single-mode holey vertical-cavity surface-emitting laser with ultra-narrow beam divergence

We demonstrated oxide-confined 850-nm vertical-cavity surface-emitting lasers (VCSELs) with a two-dimensional petal-shaped holey structure composed of several annular-sector-shaped holes. Four types of devices with different hole numbers were designed and fabricated. The measured results showed that the larger hole number was beneficial to purifying the lasing mode, and realizing the single-mode operation. The side mode suppression ratio (SMSR) exceeded 30 dB throughout the entire drive current. Mode selective loss mechanism was used to explain the single-mode characteristic. The single-mode devices possessed good beam profiles, and the lowest divergence angle was as narrow as 3.2 degrees (full width at half maximum), attributed to the graded index profile and the shallow etching in the top distributed Bragg reflector (DBR).

Nanopatterning and functionalization of phospholipid-based Langmuir-Blodgett and Langmuir-Schaefer films

Durant les dernières décennies, la technique Langmuir-Blodgett (LB) s’est beaucoup développée dans l’approche « bottom-up » pour la création de couches ultra minces nanostructurées. Des patrons constitués de stries parallèles d’environ 100 à 200 nm de largeur ont été générés avec la technique de déposition LB de monocouches mixtes de 1,2-dilauroyl-sn-glycéro-3-phosphatidylcholine (DLPC) et de 1,2-dipalmitoyl-sn-glycéro-3-phosphatidylcholine (DPPC) sur des substrats de silicium et de mica. Afin d’amplifier la fonctionnalité de ces patrons, la 1-palmitoyl-2-(16-(S-methyldithio)hexadécanoyl)-sn-glycéro-3-phosphatidylcholine (DSDPPC) et la 1-lauroyl-2-(12-(S-methyldithio)dodédecanoyl)-sn-glycéro-3-phosphatidylcholine (DSDLPC) ont été employées pour la préparation de monocouches chimiquement hétérogènes. Ces analogues de phospholipide possèdent un groupement fonctionnel méthyldisulfide qui est attaché à la fin de l’une des chaînes alkyles. Une étude exhaustive sur la structure de la phase des monocouches Langmuir, Langmuir-Schaefer (LS) et LB de la DSDPPC et de la DSDLPC et leurs différents mélanges avec la DPPC ou la DLPC est présentée dans cette thèse. Tout d’abord, un contrôle limité de la périodicité et de la taille des motifs des stries parallèles de DPPC/DLPC a été obtenu en variant la composition lipidique, la pression de surface et la vitesse de déposition. Dans un mélange binaire de fraction molaire plus grande de lipide condensé que de lipide étendu, une vitesse de déposition plus lente et une plus basse pression de surface ont généré des stries plus continues et larges. L’addition d’un tensioactif, le cholestérol, au mélange binaire équimolaire de la DPPC/DLPC a permis la formation de stries parallèles à de plus hautes pressions de surface. La caractérisation des propriétés physiques des analogues de phospholipides a été nécessaire. La température de transition de phase de la DSDPPC de 44.5 ± 1.5 °C comparativement à 41.5 ± 0.3 °C pour la DPPC. L’isotherme de la DSDPPC est semblable à celui de la DPPC. La monocouche subit une transition de phase liquide-étendue-à-condensée (LE-C) à une pression de surface légèrement supérieure à celle de la DPPC (6 mN m-1 vs. 4 mN m-1) Tout comme la DLPC, la DSDLPC demeure dans la phase LE jusqu’à la rupture de la monocouche. Ces analogues de phospholipide existent dans un état plus étendu tout au long de la compression de la monocouche et montrent des pressions de surface de rupture plus basses que les phospholipides non-modifiés. La morphologie des domaines de monocouches Langmuir de la DPPC et de la DSDPPC à l’interface eau/air a été comparée par la microscopie à angle de Brewster (BAM). La DPPC forme une monocouche homogène à une pression de surface (π) > 10 mN/m, alors que des domaines en forme de fleurs sont formés dans la monocouche de DSDPPC jusqu’à une π ~ 30 mN m-1. La caractérisation de monocouches sur substrat solide a permis de démontrer que le patron de stries parallèles préalablement obtenu avec la DPPC/DLPC était reproduit en utilisant des mélanges de la DSDPPC/DLPC ou de la DPPC/DSDLPC donnant ainsi lieu à des patrons chimiquement hétérogènes. En général, pour obtenir le même état de phase que la DPPC, la monocouche de DSDPPC doit être comprimée à de plus hautes pressions de surface. Le groupement disulfide de ces analogues de phospholipide a été exploité, afin de (i) former des monocouches auto-assemblées sur l’or et de (ii) démontrer la métallisation sélective des terminaisons fonctionnalisées des stries. La spectrométrie de photoélectrons induits par rayons X (XPS) a confirmé que la monocouche modifiée réagit avec la vapeur d’or pour former des thiolates d’or. L’adsorption de l’Au, de l’Ag et du Cu thermiquement évaporé démontre une adsorption préférentielle de la vapeur de métal sur la phase fonctionnalisée de disulfide seulement à des recouvrements sub-monocouche.

Direction Dependent Transmission Characteristics of Dye Mixture Doped Polymer Optical Fibre Preforms

The direction dependant wavelength selective transmission mechanism in poly (methyl methacrylate)(PMMA) rods doped with C 540 dye and C 540:Rh.B dye mixture as a combination has been investigated. When a polished slice of pure C 540 doped polymer rod was used side by side with a C540:Rh B doped rod with acceptor concentration [A] = 7x10-4 m/l , we could notice more than 100% change in the transmitted intensity along opposite directions at the C 540, Rh B emission and the excitation wavelengths . A blue high bright LED emitting at a peak wavelength 465nm was used as the excitation source.

Direction Dependent Transmission Characteristics of Dye Mixture Doped Polymer Optical Fibre Preforms

The direction dependant wavelength selective transmission mechanism in poly (methyl methacrylate)(PMMA) rods doped with C 540 dye and C 540:Rh.B dye mixture as a combination has been investigated. When a polished slice of pure C 540 doped polymer rod was used side by side with a C540:Rh B doped rod with acceptor concentration [A] = 7x10-4 m/l , we could notice more than 100% change in the transmitted intensity along opposite directions at the C 540, Rh B emission and the excitation wavelengths . A blue high bright LED emitting at a peak wavelength 465nm was used as the excitation source.

Direction Dependent Transmission Characteristics of Dye Mixture Doped Polymer Optical Fibre Preforms

The direction dependant wavelength selective transmission mechanism in poly (methyl methacrylate)(PMMA) rods doped with C 540 dye and C 540:Rh.B dye mixture as a combination has been investigated. When a polished slice of pure C 540 doped polymer rod was used side by side with a C540:Rh B doped rod with acceptor concentration [A] = 7x10-4 m/l , we could notice more than 100% change in the transmitted intensity along opposite directions at the C 540, Rh B emission and the excitation wavelengths . A blue high bright LED emitting at a peak wavelength 465nm was used as the excitation source.

Autonomic response in depersonalisation disorder

Background Emotional-processing inhibition has been suggested as a mechanism underlying some of the clinical features of depersonalization and/or derealization. In this study, we tested the prediction that autonomic response to emotional stimuli would be reduced in patients with depersonalization disorder. Methods The skin conductance responses of 15 patients with chronic depersonalization disorder according to DSM-IV, 15 controls, and 11 individuals with anxiety disorders according to DSM-IV, were recorded in response to nonspecific elicitors (an unexpected clap and taking a sigh) and in response to 15 randomized pictures with different emotional valences: 5 unpleasant, 5 pleasant, and 5 neutral. Results The skin conductance response to unpleasant pictures was significantly reduced in patients with depersonalization disorder (magnitude of 0.017 µsiemens in controls and 0.103 µsiemens in patients with anxiety disorders; P = .01). Also, the latency of response to these stimuli was significantly prolonged in the group with depersonalization disorder (3.01 seconds compared with 2.5 and 2.1 seconds in the control and anxiety groups, respectively; P = .02). In contrast, latency to nonspecific stimuli (clap and sigh) was significantly shorter in the depersonalization and anxiety groups (1.6 seconds) than in controls (2.3 seconds) (P = .03). Conclusions In depersonalization disorder, autonomic response to unpleasant stimuli is reduced. The fact that patients with depersonalization disorder respond earlier to a startling noise suggests that they are in a heightened state of alertness and that the reduced response to unpleasant stimuli is caused by a selective inhibitory mechanism on emotional processing.

Selective involvement of TIMP-2 in the second activational cleavage of pro-MMP-2 : refinement of the pro-MMP-2 activation mechanism

A tissue inhibitor of metalloproteinases-2 (TIMP-2)-independent mechanism for generating the first activational cleavage of pro-matrix metalloproteinase-2 (MMP-2) was identified in membrane type-1 MMP (MT1-MMP)-transfected MCF-7 cells and confirmed in TIMP-2-deficient fibroblasts. In contrast, the second MMP-2-activational step was found to be TIMP-2 dependent in both systems. MMP-2 hemopexin C-terminal domain was found to be critical for the first step processing, confirming a need for membrane tethering. We propose that the intermediate species of MMP-2 forms the well-established trimolecular complex (MT1-MMP/TIMP-2/MMP-2) for further TIMP-2-dependent autocatalytic cleavage to the fully active species. This alternate mechanism may supplement the traditional TIMP-2-mediated first step mechanism.