The Electrolytic Recovery of Copper and Zinc from Scrap Brass with Special Reference to Lead-Bearing Brass.

Several methods have been investigated, with some success, for treating scrap brass to recover copper and zinc, either as pure metals or as salts of the metals. One of the more promising of these methods is electrolysis in sulfate solution for the recovery of pure copper and zinc.

Electrolytic Recovery of Copper and Zinc from Brass

The purpose of this research was to continue the work of Thomas Parker, who worked on the recovery of copper and zinc from brass during the school year l934 - 1935. Since there is such a wide variety of brasses made with usually a third alloying constituent, remelt­ed scrap is suitable only for castings of wide tolerance in specifications.

Electrolytic Recovery of Copper and Zinc from Brass.

The reclamation of metals from scrap is becoming increasingly important in the metallurgical industry. Copper, because it does not corrode readily and is electronegative to most common metals, is peculiarly adapted to reclamation.

GFRP waste reinforced polymer mortars: a new waste management solution for GFRP scrap material

To date, glass fibre reinforced polymer (GFRP) waste recycling is very limited and restricted by thermoset nature of binder matrix and lack of economically viable enduse applications for the recyclates. In this study, efforts were made in order to recycle grinded GFRP waste proceeding from pultrusion production scrap, into new and sustainable composite materials. For this purpose, GFRP waste recyclates, a mix of powdered and fibrous materials, were incorporated into polyester based mortars as fine aggregate and filler replacements, at different load contents (between 4% up to 12% of total mass) and particle size distributions. Potential recycling solution was assessed by mechanical behaviour of resultant GFRP waste modified polymer mortars. Test results revealed that GFRP waste filled polymer mortars present improved flexural and compressive behaviour over unmodified polyester based mortars, thus indicating the feasibility of GFRP waste reuse in concrete-polymer composites.

NHL 3.5 mortars with scrap tire rubber

The use of wastes and industrial by-products as building materials is an important issue in order to decrease costs with waste management and the embodied energy of building products. Scrap tire rubber has been studied as aggregate for cementitious materials. Natural hydraulic limes are natural binders with particular characteristics of both air and hydraulic binders. Their specifications became stricter with the last version of EN 459-1:2010. In this study scrap tire rubber was used as additional aggregate of mortars, based on NHL3.5 and natural sand. Different particle size fractions and proportions of scrap tire rubber were used: a mix obtained almost directly from industry (only after sieving for preparation of particle sizes similar to mortar aggregate) and separated fine, medium and coarse fractions; 0%, 18%, 36% and 54% weight of binder, corresponding to 2.5%, 5% and 7.5% weight of sand. The influence of the rubbers´ additions on the mortars´ fresh state, mechanical and physical performance is presented, namely by flow table consistency, water retention, fresh bulk density, dynamic elasticity modulus, flexural and compressive strength, open porosity and bulk density, capillary absorption, drying and thermal conductivity. The use of the rubber mix coming from the waste tire industry seems advantageous and may open possibilities for use as raw material by the mortars industry.

Natural hydraulic lime (nhl3.5) mortars with scrap tire rubber

The use of wastes and industrial by-products as building materials is an important issue in order to decrease costs with waste management and the embodied energy of building products. In this study scrap tire rubber was used as additional aggregate of mortars based on natural hydraulic lime NHL 3.5 and natural sand. Different particle size fractions and proportions of scrap tire rubber were used: a mix obtained directly from industry and separated fine, medium and coarse fractions; 0 %, 18 %, 36 % and 54 % of the weight of binder, corresponding to 2.5 %, 5 % and 7.5 % of the weight of sand. As mortars based on NHL specifications became stricter with the current version of EN 459–1:2015, the influence of the rubber’s additions on the mortars’ fresh state, mechanical and physical performance is presented in this work: flow table consistency, water retention, dynamic elasticity modulus, flexural and compressive strength, open porosity and bulk density, capillary absorption, drying and thermal conductivity are studied. The use of the rubber mix coming from the waste tire industry seems advantageous and may open possibilities for use as raw material by the mortars industry.

PHYTOAVAILABILITY OF COPPER IN INDUSTRIAL BY-PRODUCTS AND MINERAL FERTILIZERS

Alternative copper (Cu) sources could be used in fertilizer production, although the bioavailability of copper in these materials is unknown. The objective of this study was to evaluate the extractants neutral ammonium citrate (NAC), 2 % citric acid, 1 % acetic acid, 10 % HCl, 10 % H2SO4, buffer solution pH 6.0, DTPA, EDTA, water, and hot water in the quantification of available Cu content in several sources, relating them to the relative agronomic efficiency (RAE) of wheat grown in a clayey Latossolo Vermelho eutrófico (Oxisol) and Neossolo Quartzarênico (Typic Quartzipsamment). Copper was applied at the rate of 1.5 mg kg-1 as scrap slag, brass slag, Cu ore, granulated copper, and copper sulfate. The extractants 10 % HCl, 10 % H2SO4, and NAC extracted higher Cu concentrations. The RAE values of brass slag and Cu ore were similar to or higher than those of Cu sulfate and granulated Cu. Solubility in the 2nd NAC extractant, officially required for mineral fertilizers with Cu, was lower than 60 % for the scrap slag, Cu ore, and granulated copper sources. This fact indicates that adoption of the NAC extractant may be ineffective for industrial by-products, although no extractant was more efficient in predicting Cu availability for wheat fertilized with the Cu sources tested.

Raaka-aine- ja energiatehokkuuden parantaminen Oras Oy:n valimossa

Tämän diplomityön tavoitteena oli tutkia toimintatapoja ja edellytyksiä parantaa Oras Oy:n valimon raaka-aine- ja energiatehokkuutta. Tarkastelu suoritettiin ekotehokkuusajattelun näkökulmasta. Valimon ekotehokkuutta mitattiin metallin saannon sekä valu-uunien energiatehokkuuden avulla. Tutkimustyö suoritettiin valitsemalla tarkastelun kohteeksi 20 valutuotetta. Metallin saantoa selvitettäessä punnittiin tuotteita eri työvaiheissa,jolloin saatiin selville valukanavien sekä koneistus- ja hiontavarojen osuudet valutuotteisiin panostetusta messingistä. Saantoa laskettaessa tuli myös huomioida vuosittain hylättävien tuotteiden määrät sekä messingin raaka-ainekierto kokonaisuudessaan. Valu-uunien osalta selvitettiin toiminta-ajan ja energiankulutuksen jakautuminen messingin sulattamisen ja sulan kuumanapidon kesken. Työssä tarkasteltiin, kuinka paljon metallin saantoa voitaisiin parantaa pienentämällä valukanavien ja työvarojen osuutta valoksissa sekä vähentämällähylkyjen määrää. Lisäksi tarkasteltiin muutosten vaikutuksia raaka-ainekustannuksiin sekä jätteiden määrään. Valu-uunien energiatehokkuuden parantamisen osaltatarkasteltiin käyttöasteen nostamisen eli viikoittaisen käyntiajan lisäämisen vaikutuksia energiankulutukseen ja -kustannuksiin sekä edellytyksiä pitää osa uuneista kylmänä.