Saturated-unsaturated flow through leaky dams

This research investigated seepage flow through leaky dams using the well known finite-element method. Different areas, locations, and hydraulic conductivities of leaks were examined. An area of leak, equal to 4.4% of the core area, increased the seepage flow through the dam to be about 9.5 times the seepage flow through tight (nonleaky) core. This happened for a dam having a downstream horizontal drainage filter. When the drainage filter did not exist, the increase of flow because of the same area of leak was about seven times the flow through a tight core. When the leak existed at the centerline of the core in the out-of-plane direction, its impact was slightly greater than when it existed at the edge of the core. Moreover, as the location of the leak moved up vertically, its impact was observed to be less. It was also observed that when the leak existed in curtain wall driven into underneath the dam, its impact was not significant compared with the case when it existed in the core.

A two-Dimensional finite volume method for variable density flow and solute transport through saturated-unsaturated media

Extensive groundwater withdrawal has resulted in a severe seawater intrusion problem in the Gooburrum aquifers at Bundaberg, Queensland, Australia. Better management strategies can be implemented by understanding the seawater intrusion processes in those aquifers. To study the seawater intrusion process in the region, a two-dimensional density-dependent, saturated and unsaturated flow and transport computational model is used. The model consists of a coupled system of two non-linear partial differential equations. The first equation describes the flow of a variable-density fluid, and the second equation describes the transport of dissolved salt. A two-dimensional control volume finite element model is developed for simulating the seawater intrusion into the heterogeneous aquifer system at Gooburrum. The simulation results provide a realistic mechanism by which to study the convoluted transport phenomena evolving in this complex heterogeneous coastal aquifer.

Mixed saturated-unsaturated alkyl-chain assemblies: Solid solutions of zinc stearate and zinc oleate

The linear saturated stearic acid and the bent mono-unsaturated oleic acid do not mix and form solid solutions. However, the zinc salts of these acids can. From X-ray diffraction and DSC measurements we show that the layered zinc stearate and zinc oleate salts form a homogeneous solid solution at all composition ratios. The solid solutions exhibit a single melting endotherm, with the melting temperature varying linearly with composition but with the enthalpy change showing a minimum. By monitoring features in the infrared spectra that are characteristic of the global conformation of the hydrocarbon chain, and hence can distinguish between stearate and oleate chains, it is shown that solid solution formation is realized by the introduction of gauche defects in a fraction of the stearate chains that are then no longer linear. This fraction increases with oleate concentration. It has also been possible from the spectroscopic measurements to establish a quantitative relation between molecular conformational order and the thermodynamic enthalpy of melting of the solid solutions.

饱和-非饱和土中渗流Richards方程有限元算法

发展了一种求解理查森方程的一般有限元算法.该方法采用积分法处理孔隙水压力对时间的导数项,采用集中质量技术处理有限元方程中质量矩阵来保证数值稳定.所采用的质量守恒迭代方法不须改变迭代方式,采用一般的Picard迭代方法.该方法能求解入渗、地下水位瞬变和排水等范围广泛的饱和-非饱和渗流问题.对3个已公开发表具有详细试验数据的算例的模拟表明,该方法对入渗锋、稳定渗流地下水位和非稳定渗流溢出面都模拟很好.Pieard迭代方法效率很高,且无数值振荡发生.

Effects of rainfall infiltration on deep slope failure

With the finite element method and the limit equilibrium method, a numerical model has been estab-lished for examining the effects of rainfall infiltration on the stability of slopes. This model is able to reflect the variations in pore water pressure field in slopes, dead weight of the soil, and soil softening caused by rainfall infiltration. As a case study, an actual landslide located at the Nongji Jixiao in Chongqing was studied to analyze the effects of rainfall infiltration on the seepage field and slope sta-bility. The simulated results showed that a deep slope failure is prone to occur when rainfall infiltration leads to a remarkable variation in the seepage field, especially when the pore water pressure in slopes increases in a large range.

地下水位上升造成的黄土远程滑坡形成机理与数值模拟研究

Based on field survey, laboratory testing and numerical modeling, engineering characteristics of undisturbed loess and the mechanism of long-runout loess landslides caused by underground water level rise, as well as the formation conditions and spatial distribution of landslides, are systematically studied and analyzed. Loess landslides at south Plateau of Jingyang County are mainly classified as flowslide, slide and fall. Flowslide is the main type characteristic of high velocity, long runout and multi-stages. The steep relief composed of loose structured loess-old aged soil serials and the rise of groundwater table are the predominant conditions for landslides in the study area. To study loess mechanic poperties and loess landslides mechanisims, isotropically and anisotropically consolidated undrained compression(ICU and ACU) tests and constant-deviator-drained compression (CQD) tests were carried out on undisturbed samples. The results of undrained compression tests performed at the in-situ stress level show that the soils are of consistently strain-softening in the stress-strain relations and cause high excess pore pressure. The steady-state line and the potential region of instability are obtained from ICU and ACU test results. A necessary condition for liquefaction is that the soil state initially lies in or is brought into the potential instability region. In addition, a strong strain-softening model is also formed. CQD tests demonstrate that the mobilized friction angle is far less than the steady-state angle and that the soil experiences undrained contractive failure suddenly at very small strains when its stress path during drained loading tries to cross the potential instability region，thus validates the proposed instability region. Based on the location of the region of potential instability and the stress state of slope soil, a method of static liquefaction analysis is proposed for loess landslides caused by rise in groundwater table. Compared with other liquefaction analysis methods, this method overcomes the limitations inherent in conventional slope stability method and undrained brittleness index method. Triaxial tests composed of constant water content (CW) and wetting tests at constant deviator stress are performed on undisturbed unsaturated samples. The stress-strain relation of CW tests takes on strain-hardening behavior; The results of wetting tests at constant deviator stress designed to study the mechanics of failure of unsaturated loess caused by an increase in the degree of saturation (wetting) shows that a contractive failure occurs in the undisturbed samples. On the basis of the above triaxial test results, the initiation of static liquefaction is presented for long-runout loess landslides caused by rise in groundwater table, that is, the loess slope soil gradually transfer from unsaturated to saturated state under the infiltration of irrigation. A contractive failure occurs in the local region at very small strain by increasing the pore-water pressure at constant deviator stresses under drained conditons. It is the contractive failrue resulting from rise of pore pressure that leads to high excess pore pressure in the neighbour soil which reduces shear resistance of soil. The neighbour soils also fail due to the rapid increase in pore-water pressure. Thus a connected failure surface is developed quickly and a flowslide occurs. Based on the saturated-unsaturated seepage theory, transient seepage is computed using the finite element method on loess slope under groundwater table rise. Pore-water pressure distribution for every time step after irrigation are obtained. The phreatic surface in the slope increases with the groundwater table. Pore-water pressure distribution within 8m above the phreatic surface changes very quickly，but the water content and pore water pressure in the region ranging from 8m above the phreatic surface up to ground surface is almost not affected and the matric suction usually is kept at 100～120 kPa. Based on the results of laboratory tests and seepage flow analysis, the development process of loess landslide is modeled considering groundwater table rise. The shearing plastic zone first occurs at the slope toe where the soil is soaked for long term during rise in groundwater table. As irrigation continues, the shearing plastic zone gradually extends to the interior soils, with the results that the tensile plastic zone occurs at the slope crown. As time goes on, both the shearing plastic zone and tensile plastic zone continue to extend. Then a connected plastic zone is formed and fowslide occurs. In comparision to laboratory test results, the results of numerical simulation quite well verify the presented mechanism of static liquefaction of long-runout loess landslides caused by rise in groundwater table.

降雨条件下碎石土滑坡稳定性研究

Debris Landslide is one of the types of landslides with the widest distribution, largest quantity, and the closest relationship with engineering construction. It is also one of the most important types of landslides that can cause disaster. This kind of landslide often occurs in the loose slopes which are made up of loose congeries formed by earth filling, residual soil, slope wash, dilapidation, landslide or full weathered material of hard rock. Rainfall is always the chief inducing factor of debris Landslide. Therefore, to research stability of debris Landslide during rainfall not only has important theoretical significance for understanding developing law and deformation and failure mechanism of debris landslide, but also has important practical significance for investigating, appraising, forecasting, preventing and controlling debris landslides. This thesis systematically summarized the relationships between rainfall and landslide, the method to survey water table in the landslides, the deformation and failure mechanism of debris landslide, and the progress in the stability analysis of landslides based on the analyses of data collected widely at home and abroad. The problems in the study of the stability of debris landslide during rainfall was reviewed and discussed. Due to the complicated geological conditions and the random rainfall conditions, the research on the landslides' stability must be based on engineering geological qualitative analysis. Through the collection of the data about the Panxi region and the Three Gorges Reservoir region, the author systematically summarized the engineering geological conditions, hydro-geological condition, distribution characteristics of stress field in the slope, physical and mechanical properties and hydro-mechanical properties of debris. In the viewpoint of dynamics of soil water and hydromechanics, physical process of rainfall to supply groundwater of debris landslides can be divided into two phases, i.e. non-saturated steady infiltrating phase and saturated unsteady supplying phase. The former can be described by mathematical model of surface water infiltration while the latter can be described by equivalent continuous medium model of groundwater seepage. With regard to specific hydrological geology system, we can obtain the dynamic variation law of water content, water table, landslide stability of rock and soil mass, along with quantity and duration of rainfall after the boundary condition on hydrological geology has been ascertained. This is a new way to study the response law of groundwater in the landslides during rainfall. After wet face of rock and soil mass connects with ground water table, the raising of water table will occur due to the supply of rainfall. Then interaction between ground water and rock and soil mass will occur, such as the action of physics, water, chemistry and mechanics, which caused the decrease of shearing strength of sliding zone. According to the action of groundwater on rock and soil mass, a concise mechanical model of debris landslide’s deformation was established during rainfall. The static equilibrium condition of landslide mass system was achieved according to the concise mechanical model, and then the typical deformation and failure process and failure mode of debris landslide during rainfall were discussed. In this thesis, the former limiting equilibrium slice method was modified and improved based on shearing strength theory of , a stability analysis program of debris landslide was established and developed taking account of the saturated-unsaturated seepage, by introducing the shearing strength theory of unsaturated soil mass made by (1978). The program has reasonable data storage and simple interface and is easy to operate, and can be perfectly used to carry out sensitivity analysis of influencing factors of landslides' stability, integrated with the program of Office Excel. The design of drainage engineering are always bases on empirical methods and is short of effective quantitative analysis and appraise, therefore, the conception of critical water table of debris landslide was put forward. For debris landslides with different kinds of slide face in the engineering practice, a program to search the critical water table of debris landslide was developed based on native groundwater table. And groundwater table in the slope should be declined below the critical water table in the drainage works, so the program can be directly used to guide drainage works in the debris landslide. Taking the slope deformation body in the back of former factory building of Muli Shawan hydroelectric power station as an example, a systematic and detailed research on debris landslides' stability during rainfall was researched systematically, the relationship among quantity of rainfall, water table and stability of slope was established, the debris landslides' stability in process of rainfall from dynamic viewpoint was analyzed and researched.

Characterization of tree-to-tree variation in morphological, nutritional and medicinal properties of Canarium indicum nuts

As part of a feasibility study of the commercialization potential of C. indicum nuts as Agroforestry Tree Products in Papua New Guinea, preliminary characterization studies have examined the tree-to-tree variation in morphological traits (nut and kernel mass and kernel:nut ratio), as well as nutritional (carbohydrate, fat, protein, sodium, vitamin E) and medicinal traits (anti-oxidant activity, anti-inflammatory activity and phenolic content) of kernels from 18 to 72 trees in a small number of different villages of Papua New Guinea (East New Britain Province). There was continuous variation in these traits indicating opportunities for multiple trait cultivar development targeted at food and pharmaceutical markets. Certain traits, for example anti-inflammatory activity, in which tree-to-tree variation was highly significant, present greater opportunities than others, such as saturated:unsaturated fatty acid ratio. This intraspecific variation was greater within populations than between populations. The data presented has allowed the development of a strategy to domesticate C. indicum for cultivation in homegardens and cocoa-coconut agroforests, using a participatory approach aimed at the production of agroforestry tree products (AFTPs) to empower small-holders and enhance their livelihoods and income.

Uma nova descrição para a transferência de massa em meios porosos com transição saturado-insaturado.

Esse texto trata do problema de um fluido contaminado escoando por um meio poroso, tratando os componentes na mistura como meios contínuos. Na primeira parte, desenvolvemos a teoria de misturas de meios contínuos e discutimos equações da continuidade, momento linear e momento angular. A seguir, descrevemos o problema em detalhe e fazemos hipóteses para simplificar o escoamento. Aplicamos as equações encontradas anteriormente para encontrarmos um sistema de equações diferenciais parciais. Desse ponto em diante, o problema se torna quase puramente matemático. Discutimos o caso insaturado, e depois a saturação do meio poroso. Finalmente, adicionamos um contaminante à mistura e, em seguida, N contaminantes.

填土边坡水文作用机理与破坏过程研究—以深圳羊宝地填土滑坡为例

A full understanding of failure mechanism, critical hydrological condition, and process of mobilization and deposition of a landslide is essential for optimal design of stabilization measure and forecasting of landslide hazard. This requires a quantitative study of hydrological response of a slope to rainfall through field monitoring, laboratory test and numerical modelling. At 13:40 on September 18, 2002, a fill slope failed following a period of prolonged rain in Shenzhen, resulting in 5 fatalities and 31 injuries. The failed mass with a volume about 2.5×104m3 traveled about 140m on level ground. Field monitoring, laboratory test, theoretical analysis and numerical modelling were carried out to undestand the hydrological response and failure mechanism of this fill slope. This thesis mainly focuses on the following aspects: (1) The hydrological responses and failure processes of slopes under rainfall infiltration were reviewed. Firstly, the factors influencing on the hydrological responses of slopes were analysed. Secondly, the change of stress state of slope soil and modelling methods of slope failure under rainfall infiltration were reviewed. (2) The characteristics of the Yangbaodi landslide and associated rainfall triggering the failure were presented. The failure was characterized by shallow flowslide, due to an increase of ground water table caused by rainfall infiltration. (3) A fully automated instrumentation was carried out to monitor rainfall, and saturated – unsaturated hydrological response of the fill slope, using a raingauge, piezometers, tensiometers and moisture probes. A conceptual hydrogeological model was presented based on field monitoring and borehole data. Analysis of monitoring data showed that the high pore water pressure in fill slope was caused by upward flow of semiconfined groundwater in the moderately decomposed granite. (4) Laboratory and in-situ testing was performed to study the physical and mechanical properties of fills. Isotropically consolidated undrained compression tests and anisotropically consolidated constant shear stress tests were carried out to understand the failure mechanism of the fill slope. It is indicated that loosely compacted soil is of strain-softening behaviour under undrained conditions, accompanied with a rapid increase in excess pore water pressure. In anisotropically consolidated constant shear stress tests, a very small axial strain was required to induce the failure and the excess pore water pressure increased quickly at failure. This indicated that static liquefaction caused by rise in groundwater table due to rainfall infiltration occurred. (5) The hydraulic conductivity of the highly and moderately decomposed granite was estimated using monitering data of pore water pressure. A saturated – unsaturated flow was modeled to study the hydrological response of the fill slope using rainfall records. It was observed that the lagged failure was due to the geological conditions and the discrepancy of hydraulic conductivity of slope soils. The hydraulic conductivity of moderately decomposed granite is relatively higher than the other materials, resulting in a semiconfied groundwater flow in the moderately decomposed granite, and subsequent upward flow into the upper fill layer. When the ground water table in the fill layer was increased to the critical state, the fill slope failed. (6) Numerical exercises were conducted to replay the failure process of the fill slope, based on field monitoring, laboratory and in-situ testing. It was found that the fill slope was mobilized by a rapid transfer of the concentrated shear stress. The movement of failure mass was characterized by viscosity fluid with a gradual increase in velocity. The failure process, including mobilization and subsequent movement and deposition, was studied using numerical methods.

Fatty acid composition of intramuscular fat from Nellore steers fed dry or high moisture corn and calcium salts of fatty acids

The purpose of this work was to evaluate the fatty acid composition of the Longissimus muscle from carcasses of Nellore steers fed diets with calcium salts of fatty acids (CSFA) and high moisture corn. Forty eight steers were fed during 70 days four diets containing dry corn (DC), high moisture corn (HM). dry corn plus CSFA (DC-CSFA) or high moisture corn plus CSFA (HM-CSFA). Fatty acid composition of the Longissimus muscle was determined by gas chromatography. Corn type had no effect on the ether extract percentage and in the content of the majority of the fatty acids, although steers fed HMC showed higher levels of polyunsaturated fatty acids and polyunsaturated/saturated ratio. Feeding CSFA increased ether extract percentage but had no effect on total of saturated, unsaturated and saturated: unsaturated ratio. Both high moisture corn and calcium salts of fatty acids increased CIA (cis9, trans11) and total CIA concentrations in intramuscular fat (C) 2008 Elsevier B.V. All rights reserved.

Lonomia obliqua (Lepidoptera, Saturniidae) caterpillar bristle extract induces direct lysis by cleaving erythrocyte membrane glycoproteins

Lonomia obliqua caterpillar bristle extract induces hemolysis in vitro on washed human and rat erythrocytes, in either the absence or presence of exogenous lecithin. In the former condition, phospholipases A(2) are key enzymes involved in hemolysis. However, the mechanism whereby this extract causes direct hemolysis is not known. Thus, the aim of this study was to investigate the hemolytic mechanism of the crude extract of the caterpillar L obliqua on human erythrocytes in the absence of lecithin. The extract significantly increased the erythrocyte osmotic fragility and promoted the removal of glycophorins A and C, and band 3 from the erythrocyte membrane. The use of Ca(2+) and Mg(2+) ions significantly potentiated glycoprotein removal, remarkably of erythrocyte band 3. The composition of fatty acids was analyzed by HPLC in both L obliqua caterpillar bristle extract and human erythrocyte membranes incubated with the extract. The levels of unsaturated fatty acids were remarkably augmented in erythrocytes incubated with the extract than in control erythrocytes, modifying thereby the saturated/unsaturated fatty acid ratio. Altogether, evidence is provided here that the interplay of at least three mechanisms of action accounts for the direct activity of the bristle extract on erythrocyte membrane, leading to hemolysis: the removal of glycoproteins and band 3; the insertion of fatty acids; and the action of phospholipases. Such mechanisms might affect erythrocyte flexibility and deformability, which may induce hemolysis by increasing erythrocyte fragility. However, whether the direct hemolytic activity of L obliqua caterpillar is the major cause of intravascular hemolysis during envenomation still needs further investigation. (C) 2010 Elsevier Ltd. All rights reserved.

Um estudo de percolação em barragens de terra, em regimes permanente e transiente, com a aplicação do método de elementos finitos

Este trabalho apresenta um estudo de fluxo de água em barragens de terra, em regimes permanente e transiente, com a utilização do Método de Elementos Finitos. No estudo de fluxo em regime permanente duas formas de abordar o problema são apresentadas e comparadas. A primeira considera, para a discretização da malha de elementos finitos, somente a região saturada, de maneira que a linha freática é obtida através de ajustes desta malha de elementos finitos. A segunda considera toda a região saturada-insaturada, sendo discretizado todo o domínio físico da barragem. A malha de elementos finitos não é modificada ao longo das iterações e a linha freática é obtida por interpolação dentro dos elementos, em função dos valores nodais do potencial de pressões. O desenvolvimento teórico das equações utilizadas para as duas formas de abardagem é apresentado, mostrando onde elas diferem entre si. No estudo de fluxo em regime transiente é utilizado apenas o esquema de malha fixa de elementos finitos.