Métodos de determinação de cálcio e magnésio trocáveis e estimativa do calcário residual em um Latossolo submetido à aplicação de calcário e gesso em superfície

A determinação da fração do calcário remanescente no solo (calcário residual), em área onde foi realizada aplicação de calcário em superfície, sem incorporação, na implantação do sistema plantio direto, pode ser uma ferramenta importante para auxiliar na definição do momento em que se faz necessária a reaplicação de calcário. Nesse sentido, os objetivos deste trabalho foram avaliar: quais os teores de Ca e Mg trocáveis, extraídos por percolação com solução de KCl e resina trocadora de íons; a quantidade do calcário aplicado que ainda não havia reagido no solo, mediante a determinação dos teores de Ca e Mg não-trocáveis; e qual a influência do gesso nos teores de Ca e Mg trocáveis e na dissolução do calcário, 18 meses após a aplicação em superfície. O experimento foi realizado em um Latossolo Vermelho distroférrico, em Botucatu (SP). O delineamento experimental foi de blocos casualizados com parcelas subdivididas e quatro repetições. Nas parcelas, foram aplicadas quatro doses de calcário dolomítico (0, 1.100, 2.700 e 4.300 kg ha-1), com PRNT = 71,2 %, e nas subparcelas, duas doses de gesso agrícola (0 e 2.100 kg ha-1). O calcário e o gesso foram aplicados em superfície, sem incorporação. Houve alta correlação na determinação de Ca e Mg trocável entre os métodos de percolação com solução de KCl e resina trocadora de íons. A extração pelo método da resina trocadora de íons superestimou os teores de Ca e Mg trocáveis em solo com recente aplicação de calcário em superfície. A aplicação de gesso em superfície reduziu a dissolução do calcário na camada superficial (0-0,10 m). Os teores de Ca e Mg não-trocáveis podem ser utilizados para estimar a quantidade de calcário residual no solo.

Alterações físicas e químicas do solo em função do sistema de produção e da aplicação superficial de silicato e calcário

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A estimação do efeito residual de fertilizantes por meio da Lei de Mitscherlich

This paper deals with the estimation of the residual effect of fertilizers through the use of Mitscherlich's law. The formulas and reasonings now presented are a further development of those introduced previously by PIMENTEL GOMES (2). The new formulas allow the estimation of the residual effect h in cases where the experiments are carried out in the same plots for two or three subsequent years (or crops). In an experiment analysed as an example, the residual effect of calcium hydroxide was estimated to be h = 0.423, that is, about 42%, so that one should advise the use of frequent application of small amounts of lime instead of heavy quantities used at long intervals.

Comparative evaluation of pyrethroid insecticide formulations against Triatoma infestans (Klug): residual efficacy on four substrates

We investigated the residual efficacy of four insecticide formulations used in Chagas disease vector control campaigns: cyfluthrin 12.5% suspension concentrace (SC), lambda-cyhalothrin 10% wettable powder (WP), deltamethrin 2.5% SC, and 2.5% WP on four types of circular blocks of wood, straw with mud, straw with mud painted with lime, and mud containing 5% of cement. Three concentrations of these insecticides were tested: the LC90 (previously determined on filter paper), the double of the LC90, and the recommended operational dose. For each bioassay test, 15 third-stage nymphs of Triatoma infestans (Klug) (Hemiptera: Reduviidae) were exposed for 120 h to each treatment at 24 h, 30, 60, 90, and 180 days post-spraying. Mortality rates, moulting history and behaviour were recorded at 24, 48, 72, and 120 h of exposure. Mortality rates were highest during the first 30 days post-spraying. Highest mortality rates (above 50%) were observed for deltamethrin 2.5% SC and lambda-cyhalothrin 10% WP on wood blocks up to three months post-spraying. Mud was the substrate on which treatments showed lowest persistence, with the other two substrates showing intermediate residual efficacy of all treatments. During the first 30 days WP formulations were not as effective as SC flowable formulations but, overall in the longer term, WP gave grater mortality rates of T. infestans nymphs exposed at up to six months post-spraying. Porous surfaces, especially mud, showed most variability presumably due to absorption of the insecticide. In contrast the less porous surfaces (i.e. wood and lime-coated mud) kept mortality rates high for longer post-treatment, irrespective of the insecticide concentration used.

Influence of liming on residual soil respiration and chemical properties in a tropical no-tillage system

Because of the climate changes occurring across the planet, especially global warming, the different forms of agricultural soil use have attracted researchers´ attention. Changes in soil management may influence soil respiration and, consequently, C sequestration. The objectives of this study were to evaluate the long-term influence of liming on soil respiration and correlate it with soil chemical properties after two years of liming in a no-tillage system. A randomized complete block design was used with six replications. The experimental treatments consisted of four lime rates and a control treatment without lime. Two years after liming, soil CO2 emission was measured and the soil sampled (layers 0-5, 5-10, 10-20, and 20-30 cm). The P, Ca2+ e Mg2+ soil contents and pH and base saturation were determined. CO2 emission from soil limed at the recommended rate was 24.1 % higher, and at twice the recommended rate, 47.4 % higher than from unlimed soil. Liming improved the chemical properties, and the linear increase in soil respiration rate correlated positively with the P, Ca2+ and Mg2+ soil contents, pH and base saturation, and negatively with H + Al and Al3+ contents. The correlation coefficient between soil respiration rate and chemical properties was highest in the 10-20 cm layer.

Determinação condutométria de carbonato residual do calcário aplicado no solo por análise em fluxo

The objective of this study was to evaluate a flow injection system for determination of residual CO3(2-) in soil amended with lime material. It was used a closed system were the CO2 released from soil sample acidified with 0.5 mol L-1 HCl was capted in a 0.2 mol L-1 NaOH solution. After 16h the capted CO2 was determined by conductivimetry using a flow injection system. The results obtained by the proposed method were significantly correlated with those reported in soil samples used by the International Soil Analytical Exchange Programe. The regression equation was: y = 0.987x -- 0.075 r = 0.996, P > 0.01. For acid soils amended with CaCO3 the method showed a deviation error of 2.7%, detection limit was 0.077 mmol kg-1 of CO3(2-), and a recovery of 99.7% of the total CO3(2-) added in soil sample. The method was easily adapted for routine determination of residual CO3(2-) in soil samples with an analytical frequency of 40 samples per hour.

Incorporação de CuSO4 residual em argamassa, como método de disposição final

Residual CuSO4 was incorporated into the mass utilized for cement preparation. To a cement mass with 1:0.5:5 of cement, lime and sand to 0.25, 0.50, 0.75 and 1.00% of residual CuSO4 were added. The sulfate was mixed separately with lime and water to induce metal precipitation. The hardened test bodies were submerged in Milli-Q water for three months. No Cu was detected in the water by Atomic Absorption Spectrometry. The best proportion for mechanical resistance and porosity is 0.50%. The cement is adequate for non-structural objects.

Análise de Argamassas Com Substituição Parcial do Cimento Portland Por Cinza Residual de Lenha de Algaroba

With the increase in cement consumption, it has quickly become one of the inputs most consumed by mankind over the last century. This has caused an increase in CO2 emissions, as cement production releases large quantities of this gas into the atmosphere. Adding this fact to the growing consciousness of environmental preservation, it has led to a search for alternatives to cement to complement its derivatives, in the form of waste materials like the ashes. This research aimed to analyze the properties of mortars in fresh and hardened state with partial replacement of Portland cement by residual algaroba wood ash (CRLA) potteries produced by the state of Rio Grande do Norte. The CRLA was collected and sieved, where part of it was ground and characterized in comparison with that just sifted, being characterized according to its chemical composition, grain size, fineness, density, bulk density and index of pozzolanic activity. It was found that the wood ash does not act as pozzolan, and grinding it has not changed its characteristics compared to those just sifted, not justifying its use. Two traces were adopted for this research: 1:3 (cement: fine sand) and 1:2:8 (cement: hydrated lime: medium sand); both in volume, using as materials the CRLA just sifted, CP II F-32 Portland cement, CH-I hydrated lime, river sand and water from the local utility. For each trace were adopted six percentages of partial replacement of cement for wood ash: 0% (control) 5%, 7%, 10%, 12% and 15%. In the fresh state, the mortars were tested towards their consistency index and mass density. In the hardened state, they were tested towards their tensile strength in bending, compressive strength and tensile adhesion strength, and its mass density in the hardened state. The mortar was also analyzed by scanning electron microscopy and X-ray diffraction. Furthermore, it was classified according to NBR 13281 (2005). The results showed that up to a content of 5% substitution and for both traces, the residual algaroba wood ash can replace Portland cement without compromising the mortars microstructure and its fresh and hardened state

Influence of liming on residual soil respiration and chemical properties in a tropical no-tillage system

Devido às mudanças climáticas do planeta, principalmente ao aquecimento global, as formas de utilização dos solos na agricultura têm atraído grande atenção de pesquisadores. Mudanças de manejo podem influenciar a respiração do solo e, por conseguinte, alterar drasticamente o sequestro de C. Os objetivos deste trabalho foram avaliar, em semeadura direta, a influência da calagem nas emissões de CO2 do solo e correlacioná-las aos atributos químicos deste após dois anos da calagem. Utilizou-se o delineamento em blocos casualizados, com seis repetições. Os tratamentos constituíram de quatro doses de calcário e uma testemunha. Decorridos dois anos da calagem, avaliou-se a emissão residual de CO2 do solo, coletaram-se amostras nas camadas de 0-5, 5-10, 10-20 e 20-30 cm de profundidade e determinaram-se os teores de P, Ca2+ e Mg2+ e valores de pH e de saturação por bases. A emissão residual de CO2 do solo, quando a dose recomendada foi aplicada, foi 24,1 % superior, quando comparada à do solo sem aplicação de calcário, e 47,4 % maior, quando se aplicou o dobro da dose recomendada. A calagem melhorou as condições químicas do solo, e a emissão de CO2 aumentou linearmente com o aumento das doses. A emissão de CO2 do solo apresentou correlações positivas com os teores de P, Ca2+ e Mg2+ e com os valores de pH e de saturação por bases e negativas com os teores de H + Al e Al3+. Maiores coeficientes de correlação entre as taxas de emissão de CO2 do solo e os atributos químicos deste ocorreram na camada de 10-20 cm.

Efeito residual de calcário, nitrogênio e zinco na produção de matéria seca de Brachiaria decumbens em condições de campo

The balance of liming and fertilization practice with nitrogen and zinc could affect the production of the pasture. Thus, the present work has as objective to evaluate the residual effect of the application of calcareous rock, nitrogen, and zinc on the dry matter production of Brachiaria decumbens, during three cuts. For this, an experiment was installed in Selvíria, Brazil, on a distrofic red Latosol, from october 1997 to may 1998. The experimental design was randomized blocks, in a factorial project 3×3×2, with four repetitions. The treatments were three doses of nitrogen: 0, 50, and 100 kg/ha, three doses of lime: 0, 267, and 556 kg/ha, corresponding to 41, 50, and 60% of the levels of base saturation, respectively, and two doses of zinc 0 and 5 kg/ha, applied in the first year and reapplied in the second year, except for the limestone. Four cuts were done in the grass at 10 cm of height, with intervals of 49 days, to obtain the dry matter production. The limestone application in the first year did not provide to residual effect on the production of Brachiaria decumbens. However, the nitrogen fertilization increased the dry matter production of the grass. The application of zinc in the first year and the reapplication in the second year did not result in a productive response of B. decumbens. © 2009 Instituto Nacional de Investigaciones Agricolas INIA.

Efeito residual da aplicação superficial de calcário e gesso nas culturas de soja, aveia-preta e sorgo granífero

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Efeito residual do calcário no solo, no estado nutricional e na produtividade da mangueira cv. Palmer

Pós-graduação em Agronomia (Ciência do Solo) - FCAV

Culturas de cobertura, residual de nitrogênio e reaplicação de calcário em sistema plantio direto: cultura da soja

Pós-graduação em Agronomia - FEIS

Photocatalytic Degradation Of Ofloxacin And Evaluation Of The Residual Antimicrobial Activity.

Ofloxacin is an antimicrobial agent frequently found in significant concentrations in wastewater and surface water. Its continuous introduction into the environment is a potential risk to non-target organisms or to human health. In this study, ofloxacin degradation by UV/TiO2 and UV/TiO2/H2O2, antimicrobial activity (E. coli) of samples subjected to these processes, and by-products formed were evaluated. For UV/TiO2, the degradation efficiency was 89.3% in 60 min of reaction when 128 mg L(-1) TiO2 were used. The addition of 1.68 mmol L(-1) hydrogen peroxide increased degradation to 97.8%. For UV/TiO2, increasing the catalyst concentration from 4 to 128 mg L(-1) led to an increase in degradation efficiency. For both processes, the antimicrobial activity was considerably reduced throughout the reaction time. The structures of two by-products are presented: m/z 291 (9-fluoro-3-methyl-10-(methyleneamino)-7-oxo-2,3-dihydro-7H-[1,4]oxazino[2,3,4-ij]quinoline-6-carboxylic acid) and m/z 157 ((Z)-2-formyl-3-((2-oxoethyl)imino)propanoic acid).

Caracterização física e mecânica de argamassas à base de cimento Portland e cinza de casca de arroz residual

Rice husk, employed as an energy source at milling industries in Brazil generates, after burning, a dark ash. This residue is not yet conveniently disposed, being currently dumped on large areas, causing environmental problems. This research intended to evaluate the applications of residual rice husk ashes (RHA) as a partial replacement of cement for mortar production. Rice husk ash was chemically characterized through X-ray fluorescence, determination of carbon content, X-ray diffraction, and laser granulometric analysis. Mortar specimens were submitted to two different exposure conditions: internal and external environments at a maximum period of five months. Physical-mechanical testing were compressive strength and ultrasonic pulse velocity (UPV). Although presenting good mechanical performance, the mortar based on ash (RHA) did not present pozolanicity but it can be employed in cement matrices as inert material (filler).