Experimental study on strength and ductility of steel tubular stub columns filled with geopolymeric recycled concrete

Geopolymeric recycled concrete (GRC) is a new construction material which takes environmentalsustainability into account, by using alkali solution and fly ash to completely substitute Portland cementas well as by replacing natural coarse aggregate with recycled coarse aggregate. GRC could be used togetherwith steel hollow sections to form composite section. There is very limited study on such GRC filledtubular sections. This paper presents an experimental study on GRC filled tubular stub columns. A total of 12specimens were tested. The main parameters varied in the tests are: (1) two section sizes of square hollow sections(B × t) with 200mm×6mm and 150mm×5mm; (2) different concrete types: GRC and recycled aggregateconcrete (RAC); (3) different recycled aggregate (RA) replacement ratios of 0%, 50% and 100%. The relationshipof load versus axial strain was recorded and analysed to compare the ultimate strength and failuremechanism. Meanwhile, the ductility of the columns was investigated by a ductility index (DI). The resultsshow that the ultimate strength decreased with increasing RA contents for both GRC and RAC filled columns.The influence of RA content on the strength was greater in GRC than that in RAC. The effect of RA contenton the ductility of the columns was further investigated. Simulation method for predicting load versus strainrelationship is discussed for RAC and GRC filled steel tubular columns with different RA replacement ratios.

Compressive behavior of steel fiber reinforced recycled aggregate concrete after exposure to elevated temperatures

For sustainability considerations, the use of recycled aggregate in concrete has attracted many interests in the research community. One of the main concerns for using such concrete in buildings is its spalling in fire. This may be alleviated by adding steel fibers to form steel fiber reinforced recycled aggregate concrete (SFRAC). This paper presents an experimental investigation into the compressive properties of SFRAC cylinders after exposure to elevated temperatures, including the compressive strength, Young's modulus (stiffness), stress-strain curve and energy absorption capacity (toughness). The effects of two parameters, namely steel fiber volume content (0%, 0.5%, 1%, 1.5%) and temperature (room temperature, 200 °C, 400 °C and 600 °C) on the compressive mechanical properties of concrete were investigated. The test results show that both compressive strength and stiffness of the concrete are significantly reduced after exposure to high temperatures. The addition of steel fibers is helpful in preventing spalling, and significantly improves the ductility and the cracking behavior of recycled aggregate concrete (RAC) after exposure to high temperatures, which is favorable for the application of RAC in building construction.

Desempenho de argamassas produzidas com agregados reciclados oriundos do resíduo de construção e demolição da Grande Natal-RN

The construction industry is responsible for generating a lot of waste because of their activities. Consequently, it is noticeable the occurrence of environmental problems in terms of its disposal in inappropriate places. Faced with this problem, some studies have been conducted with the aim of developing technologies and alternatives for recycling construction and demolition waste (CDW), motivated by the scarcity of natural resources and reduction of environmental problems generated. The research aims to characterize the recycled aggregates derived from construction and demolition waste (CDW) produced in the Greater Natal-RN and analyze the performance of mortar coating produced with recycled aggregates. The study includes the chemical , physical and microstructural characterization of recycled aggregates , as well as conducting microscopic analysis and laboratory tests in the fresh state (consistency index , water retention , bulk density and content of entrained air ) and in the hardened state ( compressive strength , tensile strength in bending , water absorption by immersion and capillary , mass density and void ratio ) for mortars produced from different levels of substitution of aggregates ( 0, 20 %, 40 %, 60 %, 80 % and 100 %). The results were satisfactory, providing mortars produced with recycled aggregates, smaller mass density and dynamic modulus values as well as an increase in the rates of absorption and porosity. The tensile strength in bending and compression for TP1 (1:2:8) trait were lower for mortars produced with recycled aggregates and the best result was 20% for replacement. For the TP2 (1:8) mapping, there was an increase in resistance to traction and compression and the best result was for 100% replacement of natural aggregates by recycled. The experiments led to the conclusion that the technical and economic point of view that the mortars produced with recycled aggregates can be used in construction, only if there is an effective control in production processes of recycled aggregate and at the dosage of mortars

Estudo da incorporação de resíduos de cerâmica vermelha na composição de concreto para uso em estacas moldadas in loco

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Performance estimation for concretes made with recycled aggregates of construction and demolition waste of some Brazilian cities

The aim of this paper is to verify the influence of composition variability of recycled aggregates (RA) of construction and demolition wastes (CDW) on the performance of concretes. Performance was evaluated building mathematical models for compressive strength, modulus of elasticity and drying shrinkage. To obtain such models, an experimental program comprising 50 concrete mixtures was carried out. Specimens were casted, tested and results for compressive strength, modulus of elasticity and drying shrinkage were statistically analyzed. Models inputs are CDW composition observed at seven Brazilian cities. Results confirm that using RA from CDW for concrete building is quite feasible, independently of its composition, once compressive strength and modulus of elasticity still reached considerable values. We concluded the variability presented by recycled aggregates of CDW does not compromise their use for concrete building. However, this information must be used with caution, and experimental tests should always be performed to certify concrete properties.

Estudio de hormigones reciclados no estructurales fabricados con árido reciclado mixto : propiedades mecánicas y expansión debida al contenido de sulfatos

El objetivo principal de este trabajo de investigación es estudiar las posibilidades de utilización del árido reciclado mixto para un hormigón reciclado en aplicaciones no estructurales, justificando mediante la experimentación la validez para esta aplicación, tanto del árido reciclado como del hormigón reciclado. Esta tesis se centró en los aspectos más restrictivos y limitativos en la utilización de los áridos mixtos en hormigón reciclado, basándose tanto en la normativa internacional existente como en los resultados obtenidos en los estudios bibliográficos consultados. La primera tarea realizada fue la caracterización completa de las propiedades del árido reciclado mixto, recogiendo especialmente los siguientes aspectos: granulometría, contenido de finos, absorción y densidades, composición del árido reciclado, índice de lajas, coeficiente de Los Ángeles, partículas ligeras y contenido de sulfatos. De este estudio de los áridos reciclados, se han destacado relaciones entre las propiedades. Las diferentes correlaciones permiten proponer criterios de calidad de un árido reciclado mixto para un hormigón reciclado. Se ha elegido un árido reciclado mixto entre los estudiados, de características límite admisibles, para obtener resultados conservadores sobre el hormigón reciclado fabricado con él. En una segunda etapa, se ha realizado un estudio de dosificación completo del hormigón reciclado, evaluando la consistencia del hormigón en estado fresco y la resistencia a compresión del hormigón en estado endurecido y se ha comparado con las mismas propiedades de un hormigón convencional. Se ha analizado la capacidad de absorción del árido conseguida con los métodos de presaturación empleados y en función de su estado de humedad, para poder evaluar las relaciones agua/cemento totales y efectivas del hormigón. Se ha estudiado el efecto de estos dos parámetros tanto en la consistencia como en la resistencia del hormigón reciclado. Finalmente, se ha estudiado el hormigón fabricado con un 50% y 100% de una partida de árido reciclado mixto de calidad admisible y se han ensayado las siguientes propiedades: consistencia, resistencia a compresión, resistencia a tracción indirecta, módulo de elasticidad dinámico, cambios de longitud, porosidad abierta y microscopía. Para analizar el efecto de los sulfatos, se han añadido artificialmente cantidades de yeso controladas en el hormigón reciclado. Se fabricaron hormigones con dos tipos de cemento, un cemento CEM I 42,5 R con elevado contenido de C3A, que debería dar lugar a expansiones mayores y un cemento con adiciones puzolánicas CEM II A-P 42,5 R, que atenuaría el comportamiento expansivo en el hormigón. Los resultados finales indican que la utilización del árido reciclado mixto en proporciones de hasta un 50%, permiten cubrir la gama de resistencias más exigentes dentro del hormigón no estructural. El contenido de sulfatos puede variar desde un 0,8% hasta un 1,9%, según el tipo de cemento y la proporción de sustitución del árido natural por árido reciclado mixto. Tanto en el caso del árido reciclado como en el hormigón, se ha realizado un estudio comparativo entre el conjunto de datos recopilados en la bibliografía y los obtenidos en este estudio experimental. En varias propiedades del hormigón reciclado, se han comparado los resultados con las fórmulas de la Instrucción EHE-08, para establecer unos coeficientes de corrección a aplicar a un hormigón reciclado con fines no estructurales. The main objective of this investigation work is to study the possibilities of using recycled mixed aggregate for a recycled concrete in non structural applications, justifying by means of experimentation both the validity of the recycled aggregate and recycled concrete. This thesis focused on the most restrictive and limiting aspects in the mixed aggregate use in recycled concrete, on the basis of the international standards as well on the results obtained in the bibliographic studies consulted. The first task achieved was the complete charcaterization of the mixed recycled aggregate properties, specially the following aspects: grain size analysis, fines content, absorption and densities, recycled aggregate composition, flakiness index, Los Angeles coefficient, lightweight particles and sulphate content. From this study, correlations between the properties were highlighted. The different correlations make possible to propose quality criterions for recycled mixed aggregate in concrete. Among the recycled aggregates studied, one of acceptable characteristics but near the limits established, was chosen to obtain conservative results in the recycled concrete made with it. In a second step, a complete recycled concrete mix design was made, to evaluate concrete consistency in the fresh state and concrete compressive strength in the hardened state and its properties were compared to those of a control concrete. The aggregate absorption capacity was analized with the presaturation methods achieved and in function of its state of humidity, to evaluate the total and effective water/cement ratios. The effect of these two parameters, both in consistency and compressive strength of recycled concrete, was studied. Finally, the concrete made with 50% and 100% of the elected recycled mixed aggregate was studied and the following concrete properties were tested: consistency, compressive strength, tensile strength, dynamic modulus of elasticity, length changes, water absorption under vacuum and microscopy. To analize the effect of sulphate content, some controlled quantities of gypsum were artificially added to the recycled concrete. Concretes with two types of cement were made, a cement CEM I 42,5 R with a high content of C3A, that would lead to major expansions and a cement with puzzolanic additions CEM II A-P 42,5 R that would lower the expansive behaviour of concrete. The final results indicate that the use of mixed recycled aggregate in proportions up to 50% make possible to cover the overall demanding strengths within the non structural concrete. Sulphates content can range between 0,8% and 1,9%, in function of the type of cement and the proportion of natural aggregate replacement by mixed recycled one. Both in the case of recycled aggregate and concrete, a comparative study was made between the data coming from the bibliography and those obtained in the experimental study. In several recycled concrete properties, the results were compared to the formulas of Spanish Instruction of Structural Concrete (Instruction EHE-08), to establish some correction coefficients to apply for a non structural recycled concrete.

Estudio de hormigón autocompactante con árido reciclado

La tesis doctoral “Estudio de hormigón autocompactante con árido reciclado” realizada dentro del programa de doctorado de la Universidad Politécnica de Madrid “Máster en técnicas experimentales avanzadas en la ingeniería civil”, investiga la sustitución de áridos gruesos naturales por reciclados en hormigones autocompactantes, para demostrar la posibilidad de utilización de este tipo de árido en la fabricación de hormigones autocompactantes. En cuanto a la línea experimental adoptada, la primera fase corresponde a la caracterización de los cementos y de los áridos naturales y reciclados. En ella se han obtenido las principales características físicas y mecánicas. Una vez validadas las características de todos los materiales y adoptada una dosificación de hormigón autocompactante, se han elaborado cuatro dosificaciones con cuatro grados de incorporación de árido reciclado cada una, y una dosificación con seis grados de incorporación de árido reciclado. Fabricándose un total de 22 tipos de hormigón diferentes, sin contar todas las amasadas iniciales hasta la consecución de un hormigón autocompactante. Las cinco dosificaciones se han dividido en dos grupos para poder analizar con mayor grado de definición las características de cada uno. El primer grupo es aquel que contienen los hormigones con diferentes relaciones a/c, que incluye a la muestra A (a/c=0.55), muestra D (a/c=0.50) y muestra E (a/c=0.45). Por el contrario, el segundo grupo dispone de una relación fija de a/c=0.45 pero diferentes relaciones a/c efectivas, ya que algunas de las muestras disponen de un contenido de agua que permite contrarrestar la mayor absorción del árido reciclado. Estando en este grupo la muestra E (sin agua adicional), la muestra H (con presaturación de los áridos) y la muestra I (con un aporte de agua junto con el agua de amasado. Una vez fabricados los hormigones, se pasa a la segunda fase del estudio correspondiente a la caracterización del hormigón en estado fresco. En esta fase se han llevado a cabo los ensayos de escurrimiento, escurrimiento con anillo japonés, ensayo embudo en V y embudo V a los 5 minutos. Todos estos ensayos permiten evaluar la autocompactabilidad del hormigón según el anejo 17 de la EHE-08. La tercera fase del estudio se centra en la caracterización de los hormigones en estado endurecido, evaluando las características resistentes del hormigón. Para ello, se han realizado los ensayos de resistencia a compresión, a tracción, módulo de elasticidad y coeficiente de Poisson. En la cuarta y última fase, se han analizado la durabilidad de los hormigones, debido que a pesar de ofrecer una adecuada autocompactabilidad y resistencia mecánica, se debe de obtener un hormigón con una correcta durabilidad. Para tal fin, se ha determinado la resistencia a la penetración de agua bajo presión y carbonatación de las probetas. Este último ensayo se ha realizado teniendo en cuenta las condiciones del denominado método natural, con una exposición al ambiente de 90 días y 365 días. Con todos estos resultados se elaboraron las conclusiones derivadas de la investigación, demostrándose la posibilidad de fabricación de hormigones autocompactantes con árido reciclado (HACR) con sustituciones de hasta un 40%, e incluso dependiendo de la relación a/c con sustituciones del 60% y el 80%. ABSTRACT The doctoral thesis titled Analysis of self-compacting concrete with recycled aggregates, has been developed in accordance with the doctoral program: Master degree in advanced experimental techniques in civil engineering, at UPM. It investigates the possibility of replacing natural coarse aggregates with recycled coarse aggregates, in the field of self-compacting concrete. The aim of this dissertation is to analyze the possibility of using recycled coarse aggregates in the manufacture process of self-compacting concretes. Regarding the experimental part, the first phase refers to mechanical and physical characterization of some materials such as cement, natural aggregates and recycled aggregates. Once the characteristics of all materials have been validated and the mixing proportions have been adopted, four different mixes are elaborated by using four dosage rates of recycled aggregates in each one of the samples. Moreover, an additional sample consisting of six different dosages of recycled aggregates is considered. A total number of 22 concrete specimens have been manufactured, without including all the initial kneading samples used to obtain this type of self-compacting concrete. The aforementioned mixes have been divided in two different groups to be able to analyze with more definition. The first group is the one in which the concrete contains different values of the water - cement ratio. It includes the next samples: A (w/c=0.55), D (w/c=0.50) and E (w/c=0.45). The second group has a fixed water -cement ratio, w/c=0.45, but a different effective water - cement ratio, since some of the samples have a water content that enables to offset the major absorption of the recycled aggregates, being in this group the mixing E (without additional water), the mixing H (with saturated recycled aggregate) and the mixing I (with an additional water content to the existing kneading water). Once the concrete samples have been manufactured, the following section deals with the characterization of the concrete in fresh conditions. To accomplish this, several characterization tests are carried out such as the slump-flow test, test slump flow with Japanese ring, test V-funnel and V-funnel to 5 minutes. These tests are used to assess the self-compacting conditions according to the annex 17 of the EHE-08 The third phase of the study focuses on the mechanical characterization, the assessment of the strength properties of the concrete such as compressive strength, tensile strength, modulus of elasticity and Poisson´s ratio. Within the fourth and last phase, durability of the concrete is evaluated. This fact is motivated by the need to obtain not only good self-compacting and mechanical strength properties, but also adequate durability conditions. To accomplish the aforementioned durability, resistance of the samples under certain conditions such as water penetration pressure and carbonation, has been obtained. The latter test has been carried out taking into account the natural method, with an exhibition period to the environment of 90 days and 365 days. Through the results coming from this research work, it has been possible to obtain the main conclusions. It has been demonstrated the possibility to manufacture self-compacting concrete by using recycled aggregates with replacement rates up to 40% or, depending on the w/c ratio, rates of 60% and 80% might be reached.

The incorporation of construction and demolition wastes as recycled mixed aggregates in non-structural concrete precast pieces

Concern for the environment has lately heightened awareness about the need for recycling in the construction industry. However, some standards, such as the Spanish standard, only accept the recycling of aggregates derived from concrete, which limits the extensive use of construction and demolition waste, which are produced in much bigger volumes. The aim of this work was to explore the possibility of using recycled mixed aggregates (RMA) in the preparation of precast non-structural concretes. To that end different percentages of natural aggregate were replaced by RMA in non-structural elements (25, 50, 75 and 100%). Contents of cement, water, and the dosages commonly used by companies were unchanged by the introduction of RMA. The characterization of the prepared elements has been done using the specific tests for each type of non-structural element (terrazzo for indoor use, hollow tiles, kerbstones and paving blocks): compression and flexural strength, water absorption, dimensional tolerances, abrasion and slipping resistance. The paving blocks, kerbstones, and hollow tiles prepared were tested for 360 days. The stability of the tested properties confirmed the possibility of using these wastes on an industrial scale satisfying the standard requirements. However, the surface of terrazzo with RMA is not as good as that prepared with natural aggregate.

Utilização de descarte de resíduos têxtil (poliamida/poliester), como agregado, em concreto

Neste trabalho são apresentadas algumas características físicas, vantagens e viabilidade do uso do pó de tecido, proveniente do processamento de resíduos têxteis que são descartados em confecções em geral. A produção e utilização desse tipo de pó diminui o impacto ambiental e se mostra viável economicamente, pois é produzido facilmente a partir do processamento de resíduos, que seriam descartados na natureza. O presente trabalho mostra o estudo da produção do pó de tecido e a sua substituição parcial do agregado miúdo natural na produção de concretos de cimento Portland convencionais. Para comprovar a viabilidade técnica e econômica do uso do pó de tecido foram analisadas características do agregado como sua composição granulométrica, e seu comportamento nos ensaios de abatimento tronco de cone (Slump Test). Uma relação água-cimento também foi convencionada a um concreto usual com resistência esperada de 27MPa. Com estes dados foi definido um traço para o concreto utilizando 5% e 15% de agregado pó de tecido, substituindo a areia. A pesquisa apresenta os resultados de resistência à compressão simples dos corpos de prova cilíndricos de concreto aos 28 dias. Verificou-se que as amostras não apresentaram diferenças significativas de resistência entre si, tão pouco com relação às resistências de um concreto convencional produzido somente com agregado miúdo natural. Entretanto, houve uma melhora nos resultados dos ensaios à compressão, principalmente no concreto com 15% de pó de tecido.

Avaliação do efeito da adição de resíduo de borracha de pneu e brita calcária na formulação de compósitos cimentíceos

Researches have shown that the introduction of rubber in concrete improves the features of its deformability, as well as contributes to environmental disposal of waste generated in the tire retreading process. Furthermore, there is a high availability of limestone within RN and CE country. Ignorance about this stone, does not allow its wide use as aggregate, leaving, this abundant supply idle. A composite of limestone gravel, with proportions of tire rubber waste which could be used as concrete would be an alternative to concrete for low applications. Therefore, this research aims to evaluate the characteristics of concrete containing limestone gravel and proportions of little aggregate replacement (sand) by tire rubber waste. To this goal, the material components of the concrete were characterized, concrete specimens with limestone gravel were made, from the dash 1.0: 2.5: 3.5, varying the water/cement ratio, and inserting a commercial plasticizer, without a proportion of residue, known as reference. From this, concrete with and without the presence of the additive in the same proportions were chosen, as well as these with the use of granite gravel, for being the most used. Selected the references, to these, replacements of little aggregate (sand) were added replaced by rubber waste from the tire retreading process, treated with 1M NaOH in proportions from 5.0 to 20.0 % by mass, cured and exposed to the semiarid environment. The results indicate the possibility of using limestone gravel in the concrete composition with workability correction using plasticizer. There was a decrease in the mechanical properties of the concrete with increments of waste rubber, but there is an improvement in toughness and deformability of the composite, which makes it interesting for the construction of non-structural concrete floors, as well as, the rubber waste delayed the hardening process, continuing to gain resistance after 28 days

Avaliação da durabilidade de concretos produzidos com agregados graúdos reciclados provenientes de cerâmicas vermelhas com diferentes taxas de pré-saturação

A quantidade de resíduos gerados pelo setor da Construção Civil ultimamente vem chamando atenção devido à dimensão com a qual atua como impacto ambiental utilizando materiais de fontes naturais não renováveis e aumentando as quantidades de lixos produzidos pelo meio urbano. No Brasil, esta estimativa gira em torno de 90.000 toneladas geradas por dia. A proposta de utilizar o agregado proveniente de RCC (resíduo de construção civil) como parte integrante de concretos estruturais torna-se ainda mais interessante a partir do momento em que se busca uma diminuição nos custos para a produção do concreto, carregando consigo a mentalidade ambientalista quando poupa a utilização de recursos naturais os quais alguns já começam a se esgotar. Bancos de areia e fontes de seixo começam a se extinguir devido à larga utilização desses agregados nos concretos produzidos em Belém e cidades interiores do estado do Pará. Assim a necessidade de novas fontes de agregados nos faz buscar nos resíduos da construção civil prováveis fontes de agregados que respondam de forma similar aos naturais. Levando em consideração esta proposta, esta dissertação avaliou a durabilidade de concretos produzidos com o agregado de RCC cerâmico, através de ensaios de absorção de água por capilaridade, carbonatação, penetração de íons cloretos e resistividade elétrica. Para tanto, foi substituído o agregado graúdo natural pelo agregado graúdo cerâmico em 50%, onde esta porcentagem de agregado reciclado foi submetida às taxas de pré-saturação de 60%, 80% e 100%. Nos resultados obtidos pode-se observar que a presença do AGRC (agregado graúdo reciclado cerâmico), independentemente do grau de pré-saturação foi significativa em todos os resultados obtidos, fato que embora deixe os concretos mais suscetíveis à perda de durabilidade, apresentou uma mesma tendência de comportamento em relação às misturas referência. Os resultados mais próximos das misturas convencionais foram alcançados pelos concretos que continham agregados cerâmicos pré-saturados com água à uma taxa de 80%.

Análise de misturas solo-agregado reciclados de resíduos sólidos da construção civil, para fins de pavimentação de vias urbanas de baixo volume de tráfego

This work deals with the continuation of Scientific Initiation research initiated by Tamura (2012), which draws up a mixture of soil and recycled aggregate analysis for paving of low traffic volume roads using local materials from the Vale do Paraíba region. The main steps of the process were the soil and recycled aggregate characterization, along with grading tests and California Bearing Ratio (CBR) applied to the soil, the recycled aggregate and the mixture of soil and recycled aggregate; aiming their use as base and sub-base in paving urban roads. The results are discussed, emphasizing the mechanical behavior. The current results are compared with the results of IC Tamura research, taking decisions over this job to the final product best result. For a greater understanding of the work in general were described paving, its structure, its components and its physical behavior. It has been intended to emphasize the importance of the mixture of soil and recycled aggregate to meet the quality requirements and compliance with the specifications of current technical standards, in the context of durability, natural materials economy, decreases volume in landfills and cost reduction

Estudo sobre o uso de agregados reciclados na composição de concretos e argamassas

Two of the major problems caused by construction activity are the production of construction and demolition waste (CDW) and the exploitation of mineral resources, causing big impacts on the environment. Therefore, the recycling has been shown as an alternative to mitigate the harmful effects of waste on the urban environment and prevent the exploitation of new raw materials. This course work aims to study the behavior of recycled aggregates from Vale do Paraíba in concrete and mortar. Initially, it presents the definitions of recycled aggregates according to CONAMA Resolution No. 307/2002, the aggregate settings for concrete and mortar (such as the grain size, its origin and density, and the characterization parameters according to ABNT), and the definition of ACI method of concrete mix design. Afterwards, it presents the characterization of materials separated by assays. After that, it shows the theoretical concrete proportioning applying the ACI method and experimental concrete proportioning. Then, the analysis of results is performed to finally conclude that the materials provided can't be used to replace natural aggregates because they cannot have the same performance. With the studies, it could be observed that the recycled aggregate presents a great complexity and diversity in origin, therefore the form how the material should be handled requires great care