Coolant Flow and Heat Transfer in Pebble-Bed Reactor Core

This thesis gathers knowledge about ongoing high-temperature reactor projects around the world. Methods for calculating coolant flow and heat transfer inside a pebble-bed reactor core are also developed. The thesis begins with the introduction of high-temperature reactors including the current state of the technology. Process heat applications that could use the heat from a high-temperature reactor are also introduced. A suitable reactor design with data available in literature is selected for the calculation part of the thesis. Commercial computational fluid dynamics software Fluent is used for the calculations. The pebble-bed is approximated as a packed-bed, which causes sink terms to the momentum equations of the gas flowing through it. A position dependent value is used for the packing fraction. Two different models are used to calculate heat transfer. First a local thermal equilibrium is assumed between the gas and solid phases and a single energy equation is used. In the second approach, separate energy equations are used for the phases. Information about steady state flow behavior, pressure loss, and temperature distribution in the core is obtained as results of the calculations. The effect of inlet mass flow rate to pressure loss is also investigated. Data found in literature and the results correspond each other quite well, considered the amount of simplifications in the calculations. The models developed in this thesis can be used to solve coolant flow and heat transfer in a pebble-bed reactor, although additional development and model validation is needed for better accuracy and reliability.

Isotopic prediction simulations applied to high burnup samples irradiated in VANDELLÓS-II Reactor core

Isotopic content assessment has a paramount importance for safety and storage reasons. During the latest years, a great variety of codes have been developed to perform transport and decay calculations, but only those that couple both in an iterative manner achieve an accurate prediction of the final isotopic content of irradiated fuels. Needless to say, them all are supposed to pass the test of the comparison of their predictions against the corresponding experimental measures.

Methodologies for an improved prediction of the isotopic content in high burnup samples. Application to Vandellos-II reactor core

Fuel cycles are designed with the aim of obtaining the highest amount of energy possible. Since higher burnup values are reached, it is necessary to improve our disposal designs, traditionally based on the conservative assumption that they contain fresh fuel. The criticality calculations involved must consider burnup by making the most of the experimental and computational capabilities developed, respectively, to measure and predict the isotopic content of the spent nuclear fuel. These high burnup scenarios encourage a review of the computational tools to find out possible weaknesses in the nuclear data libraries, in the methodologies applied and their applicability range. Experimental measurements of the spent nuclear fuel provide the perfect framework to benchmark the most well-known and established codes, both in the industry and academic research activity. For the present paper, SCALE 6.0/TRITON and MONTEBURNS 2.0 have been chosen to follow the isotopic content of four samples irradiated in the Spanish Vandellós-II pressurized water reactor up to burnup values ranging from 40 GWd/MTU to 75 GWd/MTU. By comparison with the experimental data reported for these samples, we can probe the applicability of these codes to deal with high burnup problems. We have developed new computational tools within MONTENBURNS 2.0. They make possible to handle an irradiation history that includes geometrical and positional changes of the samples within the reactor core. This paper describes the irradiation scenario against which the mentioned codes and our capabilities are to be benchmarked.

Dispersal of reactor core materials by reentry processes; preliminary analysis,

"Project no. AA-1506-W. Contract no. P.O. no.51-1136. Sub order no. 7, Sandia Corporation."

Generic experiments at the sump model "Zittauer Strömungswanne" (ZSW) for the behaviour of mineral wool in the sump and the reactor core

The investigation of insulation debris transport, sedimentation, penetration into the reactor core and head loss build up becomes important to reactor safety research for PWR and BWR, when considering the long-term behaviour of emergency core cooling systems during loss of coolant accidents. Research projects are being performed in cooperation between the University of Applied Sciences Zittau/Görlitz and the Helmholtz-Zentrum Dresden-Rossendorf. The projects include experimental investigations of different processes and phenomena of insulation debris in coolant flow and the development of CFD models. Generic complex experiments serve for building up a data base for the validation of models for single effects and their coupling in CFD codes. This paper includes the description of the experimental facility for complex generic experiments (ZSW), an overview about experimental boundary conditions and results for upstream and down-stream phenomena as well as for the long-time behaviour due to corrosive processes. © Carl Hanser Verlag, München.

Core Reactor Calculation Using the Adaptive Remeshing with a Current Error Estimator

With the objective to improve the reactor physics calculation on a 2D and 3D nuclear reactor via the Diffusion Equation, an adaptive automatic finite element remeshing method, based on the elementary area (2D) or volume (3D) constraints, has been developed. The adaptive remeshing technique, guided by a posteriori error estimator, makes use of two external mesh generator programs: Triangle and TetGen. The use of these free external finite element mesh generators and an adaptive remeshing technique based on the current field continuity show that they are powerful tools to improve the neutron flux distribution calculation and by consequence the power solution of the reactor core even though they have a minor influence on the critical coefficient of the calculated reactor core examples. Two numerical examples are presented: the 2D IAEA reactor core numerical benchmark and the 3D model of the Argonauta research reactor, built in Brasil.

APROS model validation in case of fast transients in a boiling water reactor

This Master´s thesis investigates the performance of the Olkiluoto 1 and 2 APROS model in case of fast transients. The thesis includes a general description of the Olkiluoto 1 and 2 nuclear power plants and of the most important safety systems. The theoretical background of the APROS code as well as the scope and the content of the Olkiluoto 1 and 2 APROS model are also described. The event sequences of the anticipated operation transients considered in the thesis are presented in detail as they will form the basis for the analysis of the APROS calculation results. The calculated fast operational transient situations comprise loss-of-load cases and two cases related to a inadvertent closure of one main steam isolation valve. As part of the thesis work, the inaccurate initial data values found in the original 1-D reactor core model were corrected. The input data needed for the creation of a more accurate 3-D core model were defined. The analysis of the APROS calculation results showed that while the main results were in good accordance with the measured plant data, also differences were detected. These differences were found to be caused by deficiencies and uncertainties related to the calculation model. According to the results the reactor core and the feedwater systems cause most of the differences between the calculated and measured values. Based on these findings, it will be possible to develop the APROS model further to make it a reliable and accurate tool for the analysis of the operational transients and possible plant modifications.

Modelling of a Hydrogen Catalytic Recombiner for Nuclear Power Plant Containment Studies; Case: Siemens FR90/1-150 Recombiner in TONUS OD Code

Ydinvoimalaitokset on suunniteltu ja rakennettu niin, että niillä on kyky selviytyä erilaisista käyttöhäiriöistä ja onnettomuuksista ilman laitoksen vahingoittumista sekä väestön ja ympäristön vaarantumista. On erittäin epätodennäköistä, että ydinvoimalaitosonnettomuus etenee reaktorisydämen vaurioitumiseen asti, minkä seurauksena sydänmateriaalien hapettuminen voi tuottaa vetyä. Jäädytyspiirin rikkoutumisen myötä vety saattaa kulkeutua ydinvoimalaitoksen suojarakennukseen, jossa se voi muodostaa palavan seoksen ilman hapen kanssa ja palaa tai jopa räjähtää. Vetypalosta aiheutuvat lämpötila- ja painekuormitukset vaarantavat suojarakennuksen eheyden ja suojarakennuksen sisällä olevien turvajärjestelmien toimivuuden, joten tehokas ja luotettava vedynhallintajärjestelmä on tarpeellinen. Passiivisia autokatalyyttisiä vetyrekombinaattoreita käytetäänyhä useammissa Euroopan ydinvoimaitoksissa vedynhallintaan. Nämä rekombinaattorit poistavat vetyä katalyyttisellä reaktiolla vedyn reagoidessa katalyytin pinnalla hapen kanssa muodostaen vesihöyryä. Rekombinaattorit ovat täysin passiivisiaeivätkä tarvitse ulkoista energiaa tai operaattoritoimintaa käynnistyäkseen taitoimiakseen. Rekombinaattoreiden käyttäytymisen tutkimisellatähdätään niiden toimivuuden selvittämiseen kaikissa mahdollisissa onnettomuustilanteissa, niiden suunnittelun optimoimiseen sekä niiden optimaalisen lukumäärän ja sijainnin määrittämiseen suojarakennuksessa. Suojarakennuksen mallintamiseen käytetään joko keskiarvoistavia ohjelmia (Lumped parameter (LP) code), moniulotteisia virtausmalliohjelmia (Computational Fluid Dynamics, CFD) tai näiden yhdistelmiä. Rekombinaattoreiden mallintaminen on toteutettu näissä ohjelmissa joko kokeellisella, teoreettisella tai yleisellä (eng. Global Approach) mallilla. Tämä diplomityö sisältää tulokset TONUS OD-ohjelman sisältämän Siemens FR90/1-150 rekombinaattorin mallin vedynkulutuksen tarkistuslaskuista ja TONUS OD-ohjelmalla suoritettujen laskujen tulokset Siemens rekombinaattoreiden vuorovaikutuksista. TONUS on CEA:n (Commissariat à 1'En¬ergie Atomique) kehittämä LP (OD) ja CFD -vetyanalyysiohjelma, jota käytetään vedyn jakautumisen, palamisenja detonaation mallintamiseen. TONUS:sta käytetään myös vedynpoiston mallintamiseen passiivisilla autokatalyyttisillä rekombinaattoreilla. Vedynkulutukseen vaikuttavat tekijät eroteltiin ja tutkittiin yksi kerrallaan. Rekombinaattoreiden vuorovaikutuksia tutkittaessa samaan tilavuuteen sijoitettiin eri kokoisia ja eri lukumäärä rekombinaattoreita. Siemens rekombinaattorimalli TONUS OD-ohjelmassa laskee vedynkulutuksen kuten oletettiin ja tulokset vahvistavat TONUS OD-ohjelman fysikaalisen laskennan luotettavuuden. Mahdollisia paikallisia jakautumia tutkitussa tilavuudessa ei voitu havaita LP-ohjelmalla, koska se käyttäälaskennassa suureiden tilavuuskeskiarvoja. Paikallisten jakautumien tutkintaan tarvitaan CFD -laskentaohjelma.

Large Break Blowdown Test Facility Study

Työn tarkoituksena on kerätä yhteen tiedot kaikista maailmalta löytyvistä ison LOCA:n ulospuhallusvaiheen tutkimiseen käytetyistä koelaitteistoista. Työn tarkoituksena on myös antaa pohjaa päätökselle, onko tarpeellista rakentaa uusi koelaitteisto nesterakenne-vuorovaikutuskoodien laskennan validoimista varten. Ennen varsinaisen koelaitteiston rakentamista olisi tarkoituksenmukaista myös rakentaa pienempi pilottikoelaitteisto, jolla voitaisiin testata käytettäviä mittausmenetelmiä. Sopivaa mittausdataa tarvitaan uusien CFD-koodien ja rakenneanalyysikoodien kytketyn laskennan validoimisessa. Näitä koodeja voidaan käyttää esimerkiksi arvioitaessa reaktorin sisäosien rakenteellista kestävyyttä ison LOCA:n ulospuhallusvaiheen aikana. Raportti keskittyy maailmalta löytyviin koelaitteistoihin, uuden koelaitteiston suunnitteluperusteisiin sekä aiheeseen liittyviin yleisiin asioihin. Raportti ei korvaa olemassa olevia validointimatriiseja, mutta sitä voi käyttää apuna etsittäessä validointitarkoituksiin sopivaa ison LOCA:n ulospuhallusvaiheen koelaitteistoa.

Thermal-Hydraulic Studies on the Safety Of VVER-440 Type Nuclear Power Plants

This thesis includes several thermal hydraulic analyses related to the Loviisa WER 440 nuclear power plant units. The work consists of experimental studies, analysis of the experiments, analysis of some plant transits and development of a calculational model for calculation of boric acid concentrations in the reactor. In the first part of the thesis, in the case of won of boric acid solution behaviour during long term cooling period of LOCAs, experiments were performed in scaled down test facilities. The experimental data together with the results of RELAPS/MOD3 simulations were used to develop a model for calculations of boric acid concentrations in the reactor during LOCAs. The results of calculations showed that margins to critical concentrations that would lead to boric acid crystallization were large, both in the reactor core and in the lower plenum. This was mainly caused by the fact that water in the primary cooling circuit includes borax (Na)BsO,.IOHZO), which enters the reactor when ECC water is taken from the sump and greatly increases boric acid solubility in water. In the second part, in the case of simulation of horizontal steam generators, experiments were performed with PACTEL integral test loop to simulate loss of feedwater transients. The PACTEL experiments, as well as earlier REWET III natural circulation tests, were analyzed with RELAPS/MOD3 Version Sm5 code. The analysis showed that the code was capable of simulating the main events during the experiments. However, in the case of loss of secondary side feedwater the code was not completely capable to simulate steam superheating in the secondary side of the steam generators. The third part of the work consists of simulations of Loviisa VVER reactor pump trip transients with RELAPSlMODI Eur, RELAPS/MOD3 and CATHARE codes. All three codes were capable to simulate the two selected pump trip transients and no significant differences were found between the results of different codes. Comparison of the calculated results with the data measured in the Loviisa plant also showed good agreement.

Monte Carlo -reaktorifysiikkalaskennan ja laskennallisen virtausmekaniikan kytkentä kuulakekoreaktorissa

Monte Carlo -reaktorifysiikkakoodit nykyisin käytettävissä olevilla laskentatehoilla tarjoavat mielenkiintoisen tavan reaktorifysiikan ongelmien ratkaisuun. Neljännen sukupolven ydinreaktoreissa käytettävät uudet rakenteet ja materiaalit ovat haasteellisia nykyisiin reaktoreihin suunnitelluille laskentaohjelmille. Tässä työssä Monte Carlo -reaktorifysiikkakoodi ja CFD-koodi yhdistetään kytkettyyn laskentaan kuulakekoreaktorissa, joka on yksi korkealämpötilareaktorityyppi. Työssä käytetty lähestymistapa on uutta maailmankin mittapuussa ajateltuna.

Reaktorisydämen valvontajärjestelmän modernisointi Olkiluodon kiehutusvesilaitoksella

Reaktorisydämen valvonnalla varmistetaan, että polttoaineelta vaaditut termiset marginaalit toteutuvat ja polttoaineen suojakuori säilyy ehjänä. Olkiluodon kiehutusvesilaitoksen nykyinen sydämen valvontajärjestelmä koostuu SIMULATE-3-sydänsimulaattoriohjelmasta, reaktorisydämen instrumentoinnista, termisen tehon laskentaohjelmasta, tiedonkeruuohjelmista ja käynnistysautomatiikasta. Uusi järjestelmä koostuu näiden lisäksi GARDEL-ohjelmasta, joka on kehitetty kevytvesireaktoreiden sydämen käytön suunnitteluun ja valvontaan. GARDEL käyttää laskentaan samoja ohjelmia, jotka ovat jo Olkiluodon kiehutusvesilaitoksella käytössä. Tämän työn tarkoituksena oli verrata nykyistä ja uutta sydämen valvontajärjestelmää Olkiluodon kiehutusvesilaitoksella. Työssä tutkittiin LPRM-detektorien kalibroinnin jälkeisen datan käsittelyä, palamapäivitystä, stabiilisuuslaskentaa ja adaptiivisia menetelmiä. Järjestelmien vertailuun käytettiin Olkiluoto 2 -laitosyksiköltä käyttöjaksolta 31 (2011–2012) saatuja laskentuloksia. Tulosten perusteella havaittiin uuden järjestelmän laskennassa yksittäisiä virheitä, jotka tulee korjata. Lisäksi uuden järjestelmän toiminnasta tarvitaan lisäselvitystä.

Vaikutusalakirjastojen muodostaminen Serpent-ARES-laskentaketjussa

Tässä diplomityössä on esitetty työn yhteydessä toteutetun Serpent-ARES-laskentaketjun muodostamiseksi tarvittavat toimenpiteet. ARES-reaktorisydän-simulaattorissa tarvittavien homogenisoitujen ryhmävakiokirjastojen muodostaminen Serpentiä käyttäen tekee laskentaketjusta muiden käytössä olevien reaktorisydämen laskentaketjujen mahdollisista virhelähteistä riippumattoman. Monte Carlo-laskentamenetelmään perustuvaa reaktorifysiikan laskentaohjelmaa käyttämällä ryhmävakiokirjastot muodostetaan uudella menetelmällä ja näin saadaan viranomaiskäyttöön voimayhtiöiden käyttämistä menetelmistä riippumaton laskentaketju reaktorien turvallisuusmarginaalien laskentaan. Työn yhteydessä muodostetun laskentaketjun ja tehtyjen vaikutusalakirjastojen muodostamisrutiinien sekä parametrisovitteiden toimivuus on todettu laskemalla Olkiluoto 3 - reaktorin alkulatauksen säätösauvojen tehokkuuksia ja sammutusmarginaaleja eri olosuhteissa. Menetelmä on todettu toimivaksi parametrien pätevyysalueella ja saadut laskentatulokset ovat oikeaa suuruusluokkaa. Parametrimallin tarkkuutta ja pätevyysaluetta on syytä vielä kehittää, ennen kuin laskentaketjua voidaan käyttää varmentamaan muilla menetelmillä laskettujen tulosten oikeellisuutta.

Application and development of numerical methods for the modelling of innovative gas cooled fission reactors

Innovative gas cooled reactors, such as the pebble bed reactor (PBR) and the gas cooled fast reactor (GFR) offer higher efficiency and new application areas for nuclear energy. Numerical methods were applied and developed to analyse the specific features of these reactor types with fully three dimensional calculation models. In the first part of this thesis, discrete element method (DEM) was used for a physically realistic modelling of the packing of fuel pebbles in PBR geometries and methods were developed for utilising the DEM results in subsequent reactor physics and thermal-hydraulics calculations. In the second part, the flow and heat transfer for a single gas cooled fuel rod of a GFR were investigated with computational fluid dynamics (CFD) methods. An in-house DEM implementation was validated and used for packing simulations, in which the effect of several parameters on the resulting average packing density was investigated. The restitution coefficient was found out to have the most significant effect. The results can be utilised in further work to obtain a pebble bed with a specific packing density. The packing structures of selected pebble beds were also analysed in detail and local variations in the packing density were observed, which should be taken into account especially in the reactor core thermal-hydraulic analyses. Two open source DEM codes were used to produce stochastic pebble bed configurations to add realism and improve the accuracy of criticality calculations performed with the Monte Carlo reactor physics code Serpent. Russian ASTRA criticality experiments were calculated. Pebble beds corresponding to the experimental specifications within measurement uncertainties were produced in DEM simulations and successfully exported into the subsequent reactor physics analysis. With the developed approach, two typical issues in Monte Carlo reactor physics calculations of pebble bed geometries were avoided. A novel method was developed and implemented as a MATLAB code to calculate porosities in the cells of a CFD calculation mesh constructed over a pebble bed obtained from DEM simulations. The code was further developed to distribute power and temperature data accurately between discrete based reactor physics and continuum based thermal-hydraulics models to enable coupled reactor core calculations. The developed method was also found useful for analysing sphere packings in general. CFD calculations were performed to investigate the pressure losses and heat transfer in three dimensional air cooled smooth and rib roughened rod geometries, housed inside a hexagonal flow channel representing a sub-channel of a single fuel rod of a GFR. The CFD geometry represented the test section of the L-STAR experimental facility at Karlsruhe Institute of Technology and the calculation results were compared to the corresponding experimental results. Knowledge was gained of the adequacy of various turbulence models and of the modelling requirements and issues related to the specific application. The obtained pressure loss results were in a relatively good agreement with the experimental data. Heat transfer in the smooth rod geometry was somewhat under predicted, which can partly be explained by unaccounted heat losses and uncertainties. In the rib roughened geometry heat transfer was severely under predicted by the used realisable k − epsilon turbulence model. An additional calculation with a v2 − f turbulence model showed significant improvement in the heat transfer results, which is most likely due to the better performance of the model in separated flow problems. Further investigations are suggested before using CFD to make conclusions of the heat transfer performance of rib roughened GFR fuel rod geometries. It is suggested that the viewpoints of numerical modelling are included in the planning of experiments to ease the challenging model construction and simulations and to avoid introducing additional sources of uncertainties. To facilitate the use of advanced calculation approaches, multi-physical aspects in experiments should also be considered and documented in a reasonable detail.