Improvement of link failure restoration utilising multi-protocol label switching (MPLS) as a means to maintain quality of service (QOS)

This paper proposes a practical approach to the enhancement of Quality of Service (QoS) routing by means of providing alternative or repair paths in the event of a breakage of a working path. The proposed scheme guarantees that every Protected Node (PN) is connected to a multi-repair path such that no further failure or breakage of single or double repair paths can cause any simultaneous loss of connectivity between an ingress node and an egress node. Links to be protected in an MPLS network are predefined and a Label Switched path (LSP) request involves the establishment of a working path. The use of multi-protection paths permits the formation of numerous protection paths allowing greater flexibility. Our analysis examined several methods including single, double and multi-repair routes and the prioritization of signals along the protected paths to improve the Quality of Service (QoS), throughput, reduce the cost of the protection path placement, delay, congestion and collision. Results obtained indicated that creating multi-repair paths and prioritizing packets reduces delay and increases throughput in which case the delays at the ingress/egress LSPs were low compared to when the signals had not been classified. Therefore the proposed scheme provided a means to improve the QoS in path restoration in MPLS using available network resources. Prioritizing the packets in the data plane has revealed that the amount of traffic transmitted using a medium and low priority Label Switch Paths (LSPs) does not have any impact on the explicit rate of the high priority LSP in which case the problem of a knock-on effect is eliminated.

Quality of Service (QoS) in MPLS networks

Telecommunications networks have been always expanding and thanks to it, new services have appeared. The old mechanisms for carrying packets have become obsolete due to the new service requirements, which have begun working in real time. Real time traffic requires strict service guarantees. When this traffic is sent through the network, enough resources must be given in order to avoid delays and information losses. When browsing through the Internet and requesting web pages, data must be sent from a server to the user. If during the transmission there is any packet drop, the packet is sent again. For the end user, it does not matter if the webpage loads in one or two seconds more. But if the user is maintaining a conversation with a VoIP program, such as Skype, one or two seconds of delay in the conversation may be catastrophic, and none of them can understand the other. In order to provide support for this new services, the networks have to evolve. For this purpose MPLS and QoS were developed. MPLS is a packet carrying mechanism used in high performance telecommunication networks which directs and carries data using pre-established paths. Now, packets are forwarded on the basis of labels, making this process faster than routing the packets with the IP addresses. MPLS also supports Traffic Engineering (TE). This refers to the process of selecting the best paths for data traffic in order to balance the traffic load between the different links. In a network with multiple paths, routing algorithms calculate the shortest one, and most of the times all traffic is directed through it, causing overload and packet drops, without distributing the packets in the other paths that the network offers and do not have any traffic. But this is not enough in order to provide the real time traffic the guarantees it needs. In fact, those mechanisms improve the network, but they do not make changes in how the traffic is treated. That is why Quality of Service (QoS) was developed. Quality of service is the ability to provide different priority to different applications, users, or data flows, or to guarantee a certain level of performance to a data flow. Traffic is distributed into different classes and each of them is treated differently, according to its Service Level Agreement (SLA). Traffic with the highest priority will have the preference over lower classes, but this does not mean it will monopolize all the resources. In order to achieve this goal, a set policies are defined to control and alter how the traffic flows. Possibilities are endless, and it depends in how the network must be structured. By using those mechanisms it is possible to provide the necessary guarantees to the real-time traffic, distributing it between categories inside the network and offering the best service for both real time data and non real time data. Las Redes de Telecomunicaciones siempre han estado en expansión y han propiciado la aparición de nuevos servicios. Los viejos mecanismos para transportar paquetes se han quedado obsoletos debido a las exigencias de los nuevos servicios, que han comenzado a operar en tiempo real. El tráfico en tiempo real requiere de unas estrictas garantías de servicio. Cuando este tráfico se envía a través de la red, necesita disponer de suficientes recursos para evitar retrasos y pérdidas de información. Cuando se navega por la red y se solicitan páginas web, los datos viajan desde un servidor hasta el usuario. Si durante la transmisión se pierde algún paquete, éste se vuelve a mandar de nuevo. Para el usuario final, no importa si la página tarda uno o dos segundos más en cargar. Ahora bien, si el usuario está manteniendo una conversación usando algún programa de VoIP (como por ejemplo Skype) uno o dos segundos de retardo en la conversación podrían ser catastróficos, y ninguno de los interlocutores sería capaz de entender al otro. Para poder dar soporte a estos nuevos servicios, las redes deben evolucionar. Para este propósito se han concebido MPLS y QoS MPLS es un mecanismo de transporte de paquetes que se usa en redes de telecomunicaciones de alto rendimiento que dirige y transporta los datos de acuerdo a caminos preestablecidos. Ahora los paquetes se encaminan en función de unas etiquetas, lo cual hace que sea mucho más rápido que encaminar los paquetes usando las direcciones IP. MPLS también soporta Ingeniería de Tráfico (TE). Consiste en seleccionar los mejores caminos para el tráfico de datos con el objetivo de balancear la carga entre los diferentes enlaces. En una red con múltiples caminos, los algoritmos de enrutamiento actuales calculan el camino más corto, y muchas veces el tráfico se dirige sólo por éste, saturando el canal, mientras que otras rutas se quedan completamente desocupadas. Ahora bien, esto no es suficiente para ofrecer al tráfico en tiempo real las garantías que necesita. De hecho, estos mecanismos mejoran la red, pero no realizan cambios a la hora de tratar el tráfico. Por esto es por lo que se ha desarrollado el concepto de Calidad de Servicio (QoS). La calidad de servicio es la capacidad para ofrecer diferentes prioridades a las diferentes aplicaciones, usuarios o flujos de datos, y para garantizar un cierto nivel de rendimiento en un flujo de datos. El tráfico se distribuye en diferentes clases y cada una de ellas se trata de forma diferente, de acuerdo a las especificaciones que se indiquen en su Contrato de Tráfico (SLA). EL tráfico con mayor prioridad tendrá preferencia sobre el resto, pero esto no significa que acapare la totalidad de los recursos. Para poder alcanzar estos objetivos se definen una serie de políticas para controlar y alterar el comportamiento del tráfico. Las posibilidades son inmensas dependiendo de cómo se quiera estructurar la red. Usando estos mecanismos se pueden proporcionar las garantías necesarias al tráfico en tiempo real, distribuyéndolo en categorías dentro de la red y ofreciendo el mejor servicio posible tanto a los datos en tiempo real como a los que no lo son.

How transit route passenger load and distance can together influence quality of service

This paper investigates: - correlation between transit route passenger loading and travel distance - its implications on quality of service (QoS) and resource productivity. It uses Automatic Fare Collection (AFC) data across a weekday on a premium bus line in Brisbane, Australia. A composite load-distance factor is proposed as a new measure for profiling transit route on-board passenger comfort QoS. Understanding these measures and their correlation is important for planning, design, and operational activities.

Generalized aggregate Quality of Service computation for composite services

This article addresses the problem of estimating the Quality of Service (QoS) of a composite service given the QoS of the services participating in the composition. Previous solutions to this problem impose restrictions on the topology of the orchestration models, limiting their applicability to well-structured orchestration models for example. This article lifts these restrictions by proposing a method for aggregate QoS computation that deals with more general types of unstructured orchestration models. The applicability and scalability of the proposed method are validated using a collection of models from industrial practice.

Transit route occupancy load factor and passenger average travel time for quality of service assessment

This paper investigates quality of service (QoS) and resource productivity implications of transit route passenger loading and travel time. It highlights the value of occupancy load factor as a direct passenger comfort QoS measure. Automatic Fare Collection data for a premium radial bus route in Brisbane, Australia, is used to investigate time series correlation between occupancy load factor and passenger average travel time. Correlation is strong across the entire span of service in both directions. Passengers tend to be making longer, peak direction commuter trips under significantly less comfortable conditions than off-peak. The Transit Capacity and Quality of Service Manual uses segment based load factor as a measure of onboard loading comfort QoS. This paper provides additional insight into QoS by relating the two route based dimensions of occupancy load factor and passenger average travel time together in a two dimensional format, both from the passenger’s and operator’s perspectives. Future research will apply Value of Time to QoS measurement, reflecting perceived passenger comfort through crowding and average time spent onboard. This would also assist in transit service quality econometric modeling. The methodology can be readily applied in a practical setting where AFC data for fixed scheduled routes is available. The study outcomes also provide valuable research and development directions.

Transit route occupancy load factor and passenger average travel time for quality of service assessment

This presentation investigates quality of service (QoS) and resource productivity implications of transit route passenger loading and travel time. It highlights the value of occupancy load factor as a direct passenger comfort QoS measure. Automatic Fare Collection data for a premium radial bus route in Brisbane, Australia, is used to investigate time series correlation between occupancy load factor and passenger average travel time. Correlation is strong across the entire span of service in both directions. Passengers tend to be making longer, peak direction commuter trips under significantly less comfortable conditions than off-peak. The Transit Capacity and Quality of Service Manual uses segment based load factor as a measure of onboard loading comfort QoS. This paper provides additional insight into QoS by relating the two route based dimensions of occupancy load factor and passenger average travel time together in a two dimensional format, both from the passenger’s and operator’s perspectives. Future research will apply Value of Time to QoS measurement, reflecting perceived passenger comfort through crowding and average time spent onboard. This would also assist in transit service quality econometric modeling. The methodology can be readily applied in a practical setting where AFC data for fixed scheduled routes is available. The study outcomes also provide valuable research and development directions.

Effects of transit quality of service characteristics on daily bus ridership

This study investigates whether an Australian city’s suburbs having high transit Quality of Service (QoS) are associated with higher transit ridership than those having low transit QoS •We explore how QoS measures including service frequency, service span, service coverage, and travel time ratio, along with implicit environmental predictors such as topographic grade factor influence bus ridership •We applied Multiple Linear Regression (MLR) to examine the relationship between QoS and ridership •Its outcomes enhance our understanding of transit user behavior, which is informative to urban transportation policy, planning, and provision

Stochastic analysis of transit route segments' passenger load variation for capacity and quality of service assessment

This paper investigates stochastic analysis of transit segment hourly passenger load factor variation for transit capacity and quality of service (QoS) analysis using Automatic Fare Collection data for a premium radial bus route in Brisbane, Australia. It compares stochastic analysis to traditional peak hour factor (PHF) analysis to gain further insight into variability of transit route segments’ passenger loading during a study hour. It demonstrates that hourly design load factor is a useful method of modeling a route segment’s capacity and QoS time history across the study weekday. This analysis method is readily adaptable to different passenger load standards by adjusting design percentile, reflecting either a more relaxed or more stringent condition. This paper also considers hourly coefficient of variation of load factor as a capacity and QoS assessment measure, in particular through its relationships with hourly average and design load factors. Smaller value reflects uniform passenger loading, which is generally indicative of well dispersed passenger boarding demands and good schedule maintenance. Conversely, higher value may be indicative of pulsed or uneven passenger boarding demands, poor schedule maintenance, and/or bus bunching. An assessment table based on hourly coefficient of variation of load factor is developed and applied to this case study. Inferences are drawn for a selection of study hours across the weekday studied.

Assessment of transit quality of service with occupancy load factor and passenger travel time measures

This paper investigates quality of service (QoS) and resource productivity implications of transit route passenger loading and travel time. It highlights the value of occupancy load factor as a direct passenger comfort QoS measure. Automatic Fare Collection data for a premium radial bus route in Brisbane, Australia, is used to investigate time series correlation between occupancy load factor and passenger average travel time. Correlation is strong across the entire span of service in both directions. Passengers tend to be making longer, peak direction commuter trips under significantly less comfortable conditions than off-peak. The Transit Capacity and Quality of Service Manual uses segment based load factor as a measure of onboard loading comfort QoS. This paper provides additional insight into QoS by relating the two route based dimensions of occupancy load factor and passenger average travel time together in a two dimensional format, both from the passenger’s and operator’s perspectives. Future research will apply Value of Time to QoS measurement, reflecting perceived passenger comfort through crowding and average time spent onboard. This would also assist in transit service quality econometric modeling. The methodology can be readily applied in a practical setting where AFC data for fixed scheduled routes is available. The study outcomes also provide valuable research and development directions.

Measuring route passenger load diversity for capacity and quality of service assessment

This paper develops theory that quantifies transit route passenger-relative load factor and distinguishes it from occupancy load factor. The ratio between these measures is defined as the load diversity coefficient, which as a single measure characterizes the diversity of passenger load factor between route segments according to the origin-destination profile. The relationship between load diversity coefficient and route coefficient of variation in occupancy load factor is quantified. Two tables are provided that enhance passenger capacity and quality of service (QoS) assessment regarding onboard passenger load. The first expresses the transit operator’s perspective of load diversity and the passengers’ perspective of load factor relative to the operator’s, across six service levels corresponding to ranges of coefficient of variation in occupancy load factor. The second interprets the relationships between passenger average travel time and each of passenger-relative load factor and occupancy load factor. The application of this methodology is illustrated using a case study of a premium radial bus route in Brisbane, Australia. The methodology can assist in benchmarking and decision making regarding route and schedule design. Future research will apply value of time to QoS measurement, reflecting perceived passenger comfort through crowding and average time spent aboard. This would also assist in transit service quality econometric modeling.

Iso-Quality of Service: Fairly Ranking Servers for Real-Time Data Analytics

We present a mathematically rigorous Quality-of-Service (QoS) metric which relates the achievable quality of service metric (QoS) for a real-time analytics service to the server energy cost of offering the service. Using a new iso-QoS evaluation methodology, we scale server resources to meet QoS targets and directly rank the servers in terms of their energy-efficiency and by extension cost of ownership. Our metric and method are platform-independent and enable fair comparison of datacenter compute servers with significant architectural diversity, including micro-servers. We deploy our metric and methodology to compare three servers running financial option pricing workloads on real-life market data. We find that server ranking is sensitive to data inputs and desired QoS level and that although scale-out micro-servers can be up to two times more energy-efficient than conventional heavyweight servers for the same target QoS, they are still six times less energy efficient than high-performance computational accelerators.

Improving quality-of-service in wireless sensor networks by mitigating “Hidden-Node Collisions”

Wireless sensor networks (WSNs) emerge as underlying infrastructures for new classes of large-scale networked embedded systems. However, WSNs system designers must fulfill the quality-of-service (QoS) requirements imposed by the applications (and users). Very harsh and dynamic physical environments and extremely limited energy/computing/memory/communication node resources are major obstacles for satisfying QoS metrics such as reliability, timeliness, and system lifetime. The limited communication range of WSN nodes, link asymmetry, and the characteristics of the physical environment lead to a major source of QoS degradation in WSNs-the ldquohidden node problem.rdquo In wireless contention-based medium access control (MAC) protocols, when two nodes that are not visible to each other transmit to a third node that is visible to the former, there will be a collision-called hidden-node or blind collision. This problem greatly impacts network throughput, energy-efficiency and message transfer delays, and the problem dramatically increases with the number of nodes. This paper proposes H-NAMe, a very simple yet extremely efficient hidden-node avoidance mechanism for WSNs. H-NAMe relies on a grouping strategy that splits each cluster of a WSN into disjoint groups of non-hidden nodes that scales to multiple clusters via a cluster grouping strategy that guarantees no interference between overlapping clusters. Importantly, H-NAMe is instantiated in IEEE 802.15.4/ZigBee, which currently are the most widespread communication technologies for WSNs, with only minor add-ons and ensuring backward compatibility with their protocols standards. H-NAMe was implemented and exhaustively tested using an experimental test-bed based on ldquooff-the-shelfrdquo technology, showing that it increases network throughput and transmission success probability up to twice the values obtained without H-NAMe. H-NAMe effectiveness was also demonstrated in a target tracking application with mobile robots - over a WSN deployment.

Quality of service-based service level agreement management framework for hydrocarbon exploration and discovery operation

 The major contributions presented in this thesis are twofold. Firstly, it presents the research towards a unique services-based Hydrocarbon Exploration and Discovery Model that demonstrates the feasibility of using advanced ICT technologies in the reproduction of stages involved in an oil and gas discovery, processing and analysis process. Secondly, the research demonstrated a solution of the problems in providing agreed level of quality of service (QoS) and formalizing of appropriate Service Level Agreements (SLA) within such complex environment where different services within the model can be delivered by a variety of service providers

Apresentação multimédia com garantias de qualidade de serviço: QoSMedEval (Quality of Service Media Evaluation Tool)

Orientador: Paulo Nazareno Maia Sampaio