Optiska egenskapers påverkanav möjligheten att trycka eftermålvärden i ISO 12647-2.

This thesis investigates how the optical properties of paperboard influences printing with targets in ISO 12647-2. The targets for optical properties in ISO 12647-2 are defined for paperboard without optical brightening agents and fluorescent brightening agents wich makes it difficult to reach the targets when printing paperboard containing these agents.Seven different types of paperboard, some with and some without the agents, have been printed and instrumentally andvisually measured to see if there is any deviation from the standard targets and if it shows visually.The result shows that paperboard containing optical brightening agents and fluorescent brightening agents can print with targets in ISO 12647-2 but in many measurments the difference between the types of paperboard were to small to assess. The differences between the types of paperboard in the instrumental measurements did not fully correspond with the waythe panel appraised them visually.

Imaging of buried targets with ground penetrating radar

Diffraction tomographic imaging is applied to the imaging of shallowly buried targets with multi-bistatic arrays of transmitters and receivers.

Vision-based detection and tracking of aerial targets for UAV collision avoidance

Machine vision represents a particularly attractive solution for sensing and detecting potential collision-course targets due to the relatively low cost, size, weight, and power requirements of the sensors involved (as opposed to radar). This paper describes the development and evaluation of a vision-based collision detection algorithm suitable for fixed-wing aerial robotics. The system was evaluated using highly realistic vision data of the moments leading up to a collision. Based on the collected data, our detection approaches were able to detect targets at distances ranging from 400m to about 900m. These distances (with some assumptions about closing speeds and aircraft trajectories) translate to an advanced warning of between 8-10 seconds ahead of impact, which approaches the 12.5 second response time recommended for human pilots. We make use of the enormous potential of graphic processing units to achieve processing rates of 30Hz (for images of size 1024-by- 768). Currently, integration in the final platform is under way.

Scaffold development using 3D printing with a starch-based polymer

Rapid prototyping (RP) techniques have been utilised by tissue engineers to produce three-dimensional (3D) porous scaffolds. RP technologies allow the design and fabrication of complex scaffold geometries with a fully interconnected pore network. Three-dimensional printing (3DP) technique was used to fabricate scaffolds with a novel micro- and macro-architecture. In this study, a unique blend of starch-based polymer powders (cornstarch, dextran and gelatin) was developed for the 3DP process. Cylindrical scaffolds of five different designs were fabricated and post-processed to enhance the mechanical and chemical properties. The scaffold properties were characterised by scanning electron microscopy (SEM), differential scanning calorimetry (DSC), porosity analysis and compression tests

Identifying key belief-based targets for promoting regular physical activity among mothers and fathers with young children

We investigated the key beliefs to target in interventions aimed at increasing physical activity (PA) among mothers and fathers of young children. Parents (288 mothers and 292 fathers) completed a Theory of Planned Behaviour belief-based questionnaire and a 1-week follow-up of PA behaviour. We found that a range of behavioural, normative, and control beliefs were significantly correlated with parents’ PA intentions and behaviour, with only a few differences observed in correlations between PA beliefs and intention and behaviour by gender. A range of key beliefs was identified as making independent contributions to parents’ PA intentions; however, the behavioural beliefs about improving parenting practices (β = 0.13), interfering with other commitments (β = −0.29); normative beliefs about people I exercise with (β = 0.20); and control beliefs about lack of time (β = −0.24), inconvenience (β = −0.14), lack of motivation (β = −0.34), were revealed as significant independent predictors of actual PA behaviour. Furthermore, we found that a limited amount of parents already hold these beliefs, suggesting that these key beliefs warrant changing and, therefore, are appropriate targets for subsequent intervention. The current study fills an empirical gap in the PA literature by investigating an at-risk group and using a well established theoretical framework to identify key beliefs that guide parents’ PA decision-making. Overall, we found support for parents being a unique group who hold distinctive behavioural, normative, and control beliefs toward PA. Attention to these key underlying beliefs will assist intervention work aimed at combating inactivity among this at-risk population.

Organ printing

Organ printing techniques offer the potential to produce living 3D tissue constructs to repair or replace damaged or diseased human tissues and organs. Using these techniques, spatial variations along multiple axes with high geometric complexity can be obtained.. The level of control offered by these technologies to develop printed tissues will allow tissue engineers to better study factors that modulate tissue formation and function, and provide a valuable tool to study the effect of anatomy on graft performance. In this chapter we discuss the history behind substrate patterning and cell and organ printing, and the rationale for developing organ printing techniques with respect to limitations of current clinical tissue engineering strategies to effectively repair damaged tissues. We discuss current 2-dimensional and 3-dimesional strategies for assembling cells as well as the necessary support materials such as hydrogels, bioinks and natural and synthetic polymers adopted for organ printing research. Furthermore, given the current state-of-the-art in organ printing technologies, we discuss some of their limitations and provide recommendations for future developments in this rapidly growing field.

Three-dimensional printing of hierarchical and tough mesoporous bioactive glass scaffolds with a controllable pore architecture, excellent mechanical strength and mineralization ability

New-generation biomaterials for bone regenerations should be highly bioactive, resorbable and mechanically strong. Mesoporous bioactive glass (MBG), as a novel bioactive material, has been used for the study of bone regeneration due to its excellent bioactivity, degradation and drug-delivery ability; however, how to construct a 3D MBG scaffold (including other bioactive inorganic scaffolds) for bone regeneration still maintains a significant challenge due to its/their inherit brittleness and low strength. In this brief communication, we reported a new facile method to prepare hierarchical and multifunctional MBG scaffolds with controllable pore architecture, excellent mechanical strength and mineralization ability for bone regeneration application by a modified 3D-printing technique using polyvinylalcohol (PVA), as a binder. The method provides a new way to solve the commonly existing issues for inorganic scaffold materials, for example, uncontrollable pore architecture, low strength, high brittleness and the requirement for the second sintering at high temperature. The obtained 3D-printing MBG scaffolds possess a high mechanical strength which is about 200 times for that of traditional polyurethane foam template-resulted MBG scaffolds. They have highly controllable pore architecture, excellent apatite-mineralization ability and sustained drug-delivery property. Our study indicates that the 3D-printed MBG scaffolds may be an excellent candidate for bone regeneration.

Neuronal nicotinic acetylcholine receptors as pharmacotherapeutic targets for the treatment of alcohol use disorders

Alcohol use disorders (AUDs) are complex and developing effective treatments will require the combination of novel medications and cognitive behavioral therapy approaches. Epidemiological studies have shown there is a high correlation between alcohol consumption and tobacco use, and the prevalence of smoking in alcoholics is as high as 80% compared to about 30% for the general population. Both preclinical and clinical data provide evidence that nicotine administration increases alcohol intake and nonspecific nicotinic receptor antagonists reduce alcohol-mediated behaviors. As nicotine interacts specifically with the neuronal nicotinic acetylcholine receptor (nAChR) system, this suggests that nAChRs play an important role in the behavioral effects of alcohol. In this review, we discuss the importance of nAChRs for the treatment of AUDs and argue that the use of FDA approved nAChR ligands, such as varenicline and mecamylamine, approved as smoking cessation aids may prove to be valuable treatments for AUDs. We also address the importance of combining effective medications with behavioral therapy for the treatment of alcohol dependent individuals.