Modified Steels for Cold-Forming U-Bolts Used In Leaf Springs Systems

In this work, a low alloy steel and a fabrication process were developed to produce U-Bolts for commercial vehicles. Thus, initially five types of no-heat treated steel were developed with different additions of chrome, nickel, and silicon to produce strain hardening effect during cold-forming processing of the U-Bolts, assuring the required mechanical properties. The new materials exhibited a fine perlite and ferrite microstructure due to aluminum and vanadium additions, well known as grain size refiners. The mechanical properties were evaluated in a servo-hydraulic test machine system-MTS 810 according to ASTM A370-03; E739 and E08m-00 standards. The microstructure and fractography analyses of the cold-formed steels were performed by using optical and scanning electronic microscope techniques. To evaluate the performance of the steels and the production process, fatigue tests were carried out under load control (tensile-tensile), R = 0.1 and f = 30 Hz. The Weibull statistic methodology was used for the analysis of the fatigue results. At the end of this work the 0.21% chrome content steel, Alloy 2, presented the best fatigue performance.

Enhanced Botrytis cinerea resistance of Arabidopsis plants grown in compost may be explained by increased expression of defense-related genes, as revealed by microarray analysis

Composts are the products obtained after the aerobic degradation of different types of organic matter waste and can be used as substrates or substrate/soil amendments for plant cultivation. There is a small but increasing number of reports that suggest that foliar diseases may be reduced when using compost, rather than standard substrates, as growing medium. The purpose of this study was to examine the gene expression alteration produced by the compost to gain knowledge of the mechanisms involved in compost-induced systemic resistance. A compost from olive marc and olive tree leaves was able to induce resistance against Botrytis cinerea in Arabidopsis, unlike the standard substrate, perlite. Microarray analyses revealed that 178 genes were differently expressed, with a fold change cut-off of 1, of which 155 were up-regulated and 23 were down-regulated in compost-grown, as against perlite-grown plants. A functional enrichment study of up-regulated genes revealed that 38 Gene Ontology terms were significantly enriched. Response to stress, biotic stimulus, other organism, bacterium, fungus, chemical and abiotic stimulus, SA and ABA stimulus, oxidative stress, water, temperature and cold were significantly enriched, as were immune and defense responses, systemic acquired resistance, secondary metabolic process and oxireductase activity. Interestingly, PR1 expression, which was equally enhanced by growing the plants in compost and by B. cinerea inoculation, was further boosted in compost-grown pathogen-inoculated plants. Compost triggered a plant response that shares similarities with both systemic acquired resistance and ABA-dependent/independent abiotic stress responses.

Development of a Filter Aid Proportioning, Mixing, and Feeding System for a Polishing Filter

The purpose of this work was to study the characteristics of the most commonly used filter aid materials and their influences on the design of proportioning, mixing, and feeding system for polishing filter family. Based on the literature survey and hands-on experience a system was designed with defined equipment and capital and operating costs. The system was designed to serve precoating and bodyfeeding applications and is easily extended to be used in multiple filter processes. Also a test procedure was carried out where influences of flux and filter cloths to accumulated cake were studied. Filter aid is needed in challenging conditions to improve filtration efficiency and cleaning, and thus extend the operating life of the filter media. Filter aid preparation and feeding system was designed for the use of two different filter aids; precoat and bodyfeed. Precoating is used before the filtration step initiates. If the solids in the filterable solution have a tendency to clog the filter bag easily, precoat is used on the filter bag to obtain better filtration efficiency and quality. Diatomite or perlite is usually used as a precoating substance. The intention is to create a uniform cake to the overall surface of the filter cloth, with predetermined thickness, 2 – 5 mm. This ensures that the clogging of the filter cloth is reduced and the filtration efficiency is increased. Bodyfeed is used if the solids in the filterable solution have a tendency to form a sticky impermeable filter cake. The cake properties are enhanced by maintaining the permeability of the accumulating cake by using the filter aid substance as bodyfeed during the filtration process.

Estudo termoanalítico da perlita hidrofobizada com óleo de linhaça

In this work, expanded perlite, a mineral clay, consisting of SiO2 and Al2O3 in the proportions of 72.1 and 18.5%, respectively, was used as an adsorbent for oil in its pure expanded form as well as hydrofobized with linseed oil. Thermogravimetry (TG), Derivative Thermogravimetry (DTG) and Differential Thermal Analysis (DTA) were used to study the thermal behavior and quantify the percent adsorption of perlite in differents processes comparing the results with the ones obtained using Gravimetric Analysis. In the process of hydrophobization with linseed oil granulometric fractions > 20, 20-32 and 32-60 mesh were used and adsorption tests with crude oil were performed in triplicate at room temperature. The results obtained by TG/DTG in dynamic atmosphere of air showed mass losses in a single step for the expanded perlite with pure adsorbed oil, indicating that the adsorption of oil was limited and that the particle size did not in this process. Linseed oil has performed well as an agent of hydrophobized perlite (32 to 60 mesh) indicating a maximum percentage of 59.9% and 68.6% the linseed with a fraction range from considering the data obtained by thermogravimetry and Gravimetry, respectively. The adsorption of oil in the expanded perlite and hydrofobized pure perlite with linseed oil did not produce good results, characterizing an increase of 0.5 to 4.6% in pure perlite and 3.3% in hydrofobized perlite with granulometric 32 to 60 mesh

Adsorção de Mn (II) e Zn (II) em soluções aquosas usando perlita expandida revestida com quitosana

In this work, chitosan was used as a coating of pure perlite in order to increase the accessibility of the groups OH- e NH2+the adsorptionof ions Mn2+ e Zn2+.The characterization results of the expanded perlite classified as microporous and whose surface area 3,176 m2 g-1after the change resulted in 4,664 m2g-1.From the thermogravimetry(TG) it was found that the percentage of coating was34,3%.The infrared analysis can prove the presence of groups Si-OH, Si-O e Al-O-Siresulting from the perlite and C=O, NH2and OH characterization of chitosan. The experiments on experiments on the adsorption of Mn and Zn were performed in the concentration range of10 a 50 mgL-1and the adsorption capacity inpH 5,8 e 5,2 was 19,49 and 23,09 mgg-1to 25 oC,respectively.The adsorption data were best fitted to Langmuir adsorption model to Langmuir adsorption model for both metalionsisindicative of monolayer adsorption. The kinetics of adsorption were calculated from the equation of Lagergren fitting the model pseudo-second-order for all initial concentrations, suggesting that adsorption of ions Mn2+ and Zn2+ follows the kinetics of pseudo-second-order and whose constant Speedk2(g/mg.min) are 0,105 e 3,98 and capacity and maximum removal qe 4,326 e 3,348,respectively.In this study we used a square wave voltammetry cathodic stripping voltammetry to quantify the adsorbed ions, and the working electrode glassy carbon, reference electrode silver / silver chloride and a platinum auxiliary electrode. The attainment of the peaks corresponding to ions Mn2+ and Zn2+ was evaluated in and electrochemical cell with a capacity of 30 mL using a buffer system (Na2HPO4/NaH2PO4)at pH 4 and was adjusted with solutionsH3PO4 0,1molL-1and NaOH 0,1 molL-1and addition of the analyte has been a cathodic peak in- 0,873 Vand detection limit of2,55x10-6molL-1para Zn.The dough used for obtaining the adsorption isotherm was 150 mg and reached in 120 min time of equilibrium for both metal ions.The maximum adsorption for 120 min with Mn concentration 20 mgL-1 and Zn 10 mgL-1,was91, 09 e 94, 34%, respectively

Avaliação da poatencialidade da perlita natural e expandida na adsorção de metais

The contamination by metal ions has been occurring for decades through the introduction of liquid effluent not treated, mainly from industrial activities, rivers and lakes, affecting water quality. For that the effluent can be disposed in water bodies, environmental standards require that they be adequately addressed, so that the concentration of metals does not exceed the limits of standard conditions of release in the receptor. Several methods for wastewater treatment have been reported in the literature, but many of them are high cost and low efficiency. The adsorption process has been used as effective for removal of metal ions. This paper presents studies to evaluate the potential of perlite as an adsorbent for removing metals in model solution. Perlite, in its natural form (NP) and expanded (EP), was characterized by X-ray fluorescence, X-ray diffraction, surface area analysis using nitrogen adsorption (BET method), scanning electron microscopy and Fourier transform infrared spectroscopy. The physical characteristic and chemical composition of the material presented were appropriate for the study of adsorption. Adsorption experiments by the method of finite bath for model solutions of metal ions Cr3+, Cu2+, Mn2+ and Ni2+ were carried out in order to study the effect of pH, mass of the adsorbent and the contact time on removal of ions in solution. The results showed that perlite has good adsorption capacity. The NP has higher adsorption capacity (mg g-1) than the EP. According to the values of the constant of Langmuir qm (mg g-1), the maximum capacity of the monolayer was obtained and in terms of proportion of mass, we found the following order experimental adsorption: Cr3+ (2.194 mg g- 1) > Ni2+ (0.585 mg g-1) > Mn2+ (0.515 mg g-1) > Cu2+ (0.513 mg g-1) and Cr3+ (1.934 mg g-1)> Ni2+ (0.514 mg g-1) > Cu2+ (0.421 mg g-1) > Mn2+ (0.364 mg g-1) on the NP and EP, respectively. The experimental data were best fitted the Langmuir model compared to Freundlich for Cu2+, Mn2+ and Ni2+. However, for the Cr3+, both models fit the experimental data

Estudo da influência da microestrutura no comportamento mecânico de juntas soldadas de um aço estrutural

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência do tratamento térmico sobre a tenacidade de um aço com AISI SAE 1045 com médio teor de carbono, avaliada por ensaios de impacto

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Cultivo protegido de melão rendilhado, em duas épocas de plantio

Pós-graduação em Agronomia (Produção Vegetal) - FCAV

Análise microestrutural e caracterização mecânica do aço AISI 4350 submetido a diferentes tratamentos térmicos

The multiphase steels are gaining increasing attention in scientific studies because of the different mechanical and microstructural properties that the material can achieve under different thermomechanical and heat treatments that can be submitted. In the present study, it was made a microstructural study thru the triple attack technic associated with optical microscopy and mechanical characterization of medium carbon AISI 4350 steel thru a tensile strength test, subjected to three routes of heat treatment: annealing, quenching and tempering and isothermal annealing. It was verified the predominance of ferrite-perlite constituent in the specimen annealed, martensitic in the quenched and tempered specimen and bainitic in the annealed isothermally specimen. The annealed material showed a higher ductility, while the hardened and tempered specimen showed the highest hardness and ultimately the bainitic specimen showed a combination of the two abovementioned mechanical properties. Thus, we proved that the multiphase steel SAE 4350 can be a versatile material with great potential for various industrial applications

Análise microestrutural e caracterização mecânica do aço AISI 4350 submetido a diferentes tratamentos térmicos

The multiphase steels are gaining increasing attention in scientific studies because of the different mechanical and microstructural properties that the material can achieve under different thermomechanical and heat treatments that can be submitted. In the present study, it was made a microstructural study thru the triple attack technic associated with optical microscopy and mechanical characterization of medium carbon AISI 4350 steel thru a tensile strength test, subjected to three routes of heat treatment: annealing, quenching and tempering and isothermal annealing. It was verified the predominance of ferrite-perlite constituent in the specimen annealed, martensitic in the quenched and tempered specimen and bainitic in the annealed isothermally specimen. The annealed material showed a higher ductility, while the hardened and tempered specimen showed the highest hardness and ultimately the bainitic specimen showed a combination of the two abovementioned mechanical properties. Thus, we proved that the multiphase steel SAE 4350 can be a versatile material with great potential for various industrial applications

Caratterizzazione e simulazione di processi di colata in sabbia di ghise sferoidali

L’oggetto principale delle attività di tesi è la caratterizzazione numerico-sperimentale di processi di colata in sabbia di ghisa sferoidale. Inizialmente è stata effettuata un’approfondita indagine bibliografica per comprendere appieno le problematiche relative all’influenza dei parametri del processo fusorio (composizione chimica, trattamento del bagno, velocità di raffreddamento) sulle proprietà microstrutturali e meccaniche di getti ottenuti e per valutare lo stato dell’arte degli strumenti numerici di simulazione delle dinamiche di solidificazione e di previsione delle microstrutture. Sono state definite, realizzate ed impiegate attrezzature sperimentali di colata per la caratterizzazione di leghe rivolte alla misura ed alla differenziazione delle condizioni di processo, in particolare le velocità di raffreddamento, ed atte a validare strumenti di simulazione numerica e modelli previsionali. Inoltre sono stati progettati ed impiegati diversi sistemi per l’acquisizione ed analisi delle temperature all’interno di getti anche di grandi dimensioni. Lo studio, mediante analisi metallografica, di campioni di materiale ottenuto in condizioni differenziate ha confermato l’effetto dei parametri di processo considerati sulle proprietà microstrutturali quali dimensioni dei noduli di grafite e contenuto di ferrite e perlite. In getti di grandi dimensioni si è riscontrata anche una forte influenza dei fenomeni di macrosegregazione e convezione della lega su microstrutture e difettologie dei getti. Le attività si sono concentrate principalmente nella simulazione numerica FEM dei processi fusori studiati e nell’impiego di modelli empirico-analitici per la previsione delle microstrutture. I dati misurati di temperature di processo e di microstrutture sono stati impiegati per la validazione ed ottimizzazione degli strumenti numerici previsionali impiegati su un ampio intervallo di condizioni di processo. L’impiego di strumenti affidabili di simulazione del processo fusorio, attraverso l’implementazione di correlazioni sperimentali microstrutture-proprietà meccaniche, permette la valutazione di proprietà e difettologie dei getti, fornendo un valido aiuto nell’ottimizzazione del prodotto finito e del relativo processo produttivo.

Fertilización nitrogenada en plantines de pimiento (Capsicum annuum L.) cultivados en sustratos con diferentes proporciones de materiales compostados : efecto sobre los parámetros de calidad del plantín

La etapa inicial en el crecimiento de los plantines constituye el momento más crítico en su producción. Los materiales compostados pueden resultar beneficiosos por el aporte de nutrientes y la mejora en la condición física del medio de crecimiento. Para evaluar el efecto de sustratos preparados con y sin materiales compostados [Testigo (60% turba de Sphagnum+40% perlita); Mezcla I (45% turba de Sphagnum+30% perlita+25% material compostado); Mezcla II (30% turba de Sphagnum+20% perlita+50% material compostado) y un sustrato Comercial (turba de Sphagnum+40% compost+perlita+vermiculita], sobre la nutrición inicial de plantines de pimiento (Capsicum annuum L.), se realizó un ensayo fertilizando con 0, 150 y 300 mg N L-1. Se determinaron altura, diámetro del tallo y pesos frescos y secos de hoja, tallo y raíz. Se calculó relación vástago/raíz y hoja/tallo en fresco y seco, y porcentual de materia seca. El diseño experimental fue completamente aleatorizado con cuatro repeticiones. Los materiales compostados mejoraron la calidad de los plantines, los cuales no fueron afectados cuando se aplicó N a los sustratos con compost, y sólo se observaron leves mejoras en el crecimiento de los plantines al fertilizar los sustratos carentes de compost, debido a su escasa retención hídrica y elevada lixiviación de N.

Sustrato y dosis de fertirriego en la aclimatización de vitroplantas de Agave americana var. oaxacencis

Con la finalidad de asegurar la adaptación en invernadero de plantas de Agave americana var. oaxacensis obtenidas in vitro, se evaluó el efecto de sustratos y dosis de fertirriego en la aclimatización y crecimiento de 180 plantas. Este trabajo se realizó en un invernadero del Instituto Tecnológico del Valle de Oaxaca, México, a principios de 2012. Se utilizaron plantas recién salidas del laboratorio. El experimento se estableció según el diseño completamente al azar con arreglo factorial 2 (sustratos: arena y perlita) x 5 (fertilización: 1, 25, 50, 75 y 100%). La unidad experimental fue una planta en un recipiente de plástico de 150 cm3 con 18 repeticiones. La fertilización se basó en la solución universal de Steiner y diariamente cada planta recibió a nivel de sustrato 10 mL durante 12 semanas. Se evaluó el crecimiento en hojas, tallo y raíz, realizando análisis de varianza y prueba de medias (Tukey, α = 0,05). Todas las plantas se adaptaron, pero aquellas plantas establecidas en perlita lograron los mejores crecimientos en área foliar, volumen de raíz, peso fresco total, materia seca de raíz y total de planta. El tamaño de las plantas al término de su aclimatación estuvo en relación con la cantidad de nutrimentos de la solución nutritiva.

The casing layer in the culture of Agaricus bisporus, the cultivated mushroom

The casing layer is an essential component of the system employed in the culture of Agaricus bisporus. The literature appropriate to the casing layer is fully reviewed, including aspects relating to fructification and morphogenesis in A.bisporus, together with an appraisal of the various media employed, their properties and functions, and the commercial significance of the casing layer. Equipment is described for use in experiments in mushroom culture, based on a scaled-down version of normal growing technique, allowing the analysis of both weights and number of fruitbodies forming, which was useful in assessing the effects of different casing treatments. The basic steps in the production of fruitbodies in A.bisporus.are described, including a photographic study of the colonisation of casing and fructification. Various alterations to the physical structure of peat/chalk casing mixtures were found to have an effect on fructification; those causing an opening-out of the casing structure tended to give better yields, especially in the early stages of production. It was shown that, in order to obtain greater yield through casing amendment, fructification must be stimulated, giving increased numbers of fruitbodies, disproportionate to their total weight and consequently of lower mean weight. A synthetic casing medium based on the light glass-like mineral, perlite, was developed. The best formula obtained was -.1 part perlite: 1 part montmorillonite clay (by weight): 3 parts 0.01% glucose solution. Perlite/montmorillonite casing could be improved by adding compost colonised by mycelium of A.bisporus, or adding a peat-chalk casing extract. Perlite was also found to be suitable for admixture with the standard casing medium and a mixture of equal parts by volume performed as well as the peat/chalk casing normally used.