Use of Photovoltaic on an E-bike? : A Feasibility Study

In recent years the number of bicycles with e-motors has been increased steadily. Within the pedelec – bikes where an e-motor supports the pedaling – a special group of transportation bikes has developed. These bikes have storage boxes in addition to the basic parts of a bike. Due to the space available on top of those boxes it is possible to install a PV system to generate electricity which could be used to recharge the battery of the pedelec. Such a system would lead to grid independent charging of the battery and to the possibility of an increased range of motor support. The feasibility of such a PV system is investigated for a three wheeled pedelec delivered by the company BABBOE NORDIC.The measured data of the electricity generation of this mobile system is compared to the possible electricity generation of a stationary system.To measure the consumption of the pedelec different tracks are covered, and the energy which is necessary to recharge the bike battery is measured using an energy logger. This recharge energy is used as an indirect measure of the electricity consumption. A PV prototype system is installed on the bike. It is a simple PV stand alone system consisting of PV panel, charge controller with MPP tracker and a solar battery. This system has the task to generate as much electricity as possible. The produced PV current and voltage aremeasured and documented using a data logger. Afterwards the average PV power is calculated. To compare the produced electricity of the on-bike system to that of a stationary system, the irradiance on the latter is measured simultaneously. Due to partial shadings on the on-bike PV panel, which are caused by the driver and some other bike parts, the average power output during riding the bike is very low. It is too low to support the motor directly. In case of a similar installation as the PV prototype system and the intention always to park the bike on a sunny spot an on-bike system could generate electricity to at least partly recharge a bike battery during one day. The stationary PV system using the same PV panel could have produced between 1.25 and 8.1 times as much as the on-bike PV system. Even though the investigation is done for a very specific case it can be concluded that anon-bike PV system, using similar components as in the investigation, is not feasible to recharge the battery of a pedelec in an appropriate manner. The biggest barrier is that partial shadings on the PV panel, which can be hardly avoided during operation and parking, result in a significant reduction of generated electricity. Also the installation of the on-bike PV system would lead to increased weight of the whole bike and the need for space which is reducing the storage capacity. To use solar energy for recharging a bike battery an indirect way is giving better results. In this case a stationary PV stand alone system is used which is located in a sunny spot without shadings and adjusted to use the maximum available solar energy. The battery of the bike is charged using the corresponding charger and an inverter which provides AC power using the captured solar energy.

UTFORMNING AV GÅNG-, CYKEL- OCH MOPED-NÄT ANPASSAT FÖR ELCYKEL

Purpose: An increase in the number of pedelecs on Swedish roads is according to studies soon reality. This creates a need to adapt the bmp-grid (bike-, moped- and pedestrian-grid) to pedelecs for them to experience good security, accessibility and comfort while using it. The guidelines Swedish municipalities follow are VGU(Design of Roads and Streets) and the GCM-manual(Bike-, moped-, and pedestrian-manual) which currently do not take society’s future increase of pedelecs into account. VGU and the GCM-manual are tools that are commonly used during planning and design of roads and streets. The aim of the thesis is to use current advice and recommendations on how to adapt the bmp-grid to the pedelec and with this complete current guidelines for bmp-infrastructure. Method: The document-analysis is made on current federal documents that have an impact on bmp-design. Scetch-suggestions were then developed from the author’s personal improvement suggestions and from advice and recommendations gathered during the document-analysis and the theoretical framework. Findings: It was discovered that if the bmp-grid’s design allow bikes traveling up to 30km/h and has a good standard for bicycles according to VGU, then the infrastructure generally fulfil the needs of the pedelec. Altough there are still areas in VGU that needs complements. This need to be done on the design-guidelines so they can aid the adaption of the infrastructure to the pedelec during the planning- and design process. Necessary steps according to the result is to give clearer notifications on bmp-design, issue guidelines for choosing DTS, motivate minimal widths on roads, categories bikers and pedestrians into separate groups, give out more detailed descriptions of when separation of bikers and pedestrians should be done and also to specify different types of bike-users. When taking needs and claim of the pedelec into consideration the result shows that: adaption of the whole bmp-grid to the pedelec is not possible, to simplify priorities the bmp-grid needs to be divided into different sections, space should be taken from the car-traffic, solutions with mixed-traffic and bike-fields for pedelecs can be used in low-speed areas, larger opportunities to connect towns to increase commuting with bicycles appeared with the pedelec. Implications: After examining current guidelines regarding the design of the bmp-grid and gathering opinions on this from interviews the conclusion is that several areas in VGU needs completion. The following are recommendations on how to take the pedelec into consideration during the design-process:• Connect towns and urban-areas with bmp-grids to make use of pedelecs capacity.• Where there is not enough space for both cars and separated pedelec- and bike lanes the speed for car-traffic can be lowered to 30km/h. This creates opportunities with mixed-traffic or bike-lanes.• The width of existing roads and streets are often greater than what’s described in VGU. They can be made smaller to free space on roads for bicycle-infrastructure.• To prioritize which parts of the bmp-grid that needs design to allow pedelecs the bmp-grid can be divided into main- and local grid. The main grid should be design with consideration to the needs and claim of the pedelecs. Limitations: The limitation of the study lies in that none of the interviews where done with employees in any of the bigger municipalities in Sweden. This gives the study a general application in small- to middle-sized cities but not in bigger cities.Keywords: elcykel, ebike, pedelec, utformning, cykel, infrastruktur, infrastructure, society, planering, utformning, säkerhet, fordonstyp