Feasibility of industrial implementation of laser cutting into paper making machine

Laser cutting implementation possibilities into paper making machine was studied as the main objective of the work. Laser cutting technology application was considered as a replacement tool for conventional cutting methods used in paper making machines for longitudinal cutting such as edge trimming at different paper making process and tambour roll slitting. Laser cutting of paper was tested in 70’s for the first time. Since then, laser cutting and processing has been applied for paper materials with different level of success in industry. Laser cutting can be employed for longitudinal cutting of paper web in machine direction. The most common conventional cutting methods include water jet cutting and rotating slitting blades applied in paper making machines. Cutting with CO2 laser fulfils basic requirements for cutting quality, applicability to material and cutting speeds in all locations where longitudinal cutting is needed. Literature review provided description of advantages, disadvantages and challenges of laser technology when it was applied for cutting of paper material with particular attention to cutting of moving paper web. Based on studied laser cutting capabilities and problem definition of conventional cutting technologies, preliminary selection of the most promising application area was carried out. Laser cutting (trimming) of paper web edges in wet end was estimated to be the most promising area where it can be implemented. This assumption was made on the basis of rate of web breaks occurrence. It was found that up to 64 % of total number of web breaks occurred in wet end, particularly in location of so called open draws where paper web was transferred unsupported by wire or felt. Distribution of web breaks in machine cross direction revealed that defects of paper web edge was the main reason of tearing initiation and consequent web break. The assumption was made that laser cutting was capable of improvement of laser cut edge tensile strength due to high cutting quality and sealing effect of the edge after laser cutting. Studies of laser ablation of cellulose supported this claim. Linear energy needed for cutting was calculated with regard to paper web properties in intended laser cutting location. Calculated linear cutting energy was verified with series of laser cutting. Practically obtained laser energy needed for cutting deviated from calculated values. This could be explained by difference in heat transfer via radiation in laser cutting and different absorption characteristics of dry and moist paper material. Laser cut samples (both dry and moist (dry matter content about 25-40%)) were tested for strength properties. It was shown that tensile strength and strain break of laser cut samples are similar to corresponding values of non-laser cut samples. Chosen method, however, did not address tensile strength of laser cut edge in particular. Thus, the assumption of improving strength properties with laser cutting was not fully proved. Laser cutting effect on possible pollution of mill broke (recycling of trimmed edge) was carried out. Laser cut samples (both dry and moist) were tested on the content of dirt particles. The tests revealed that accumulation of dust particles on the surface of moist samples can take place. This has to be taken into account to prevent contamination of pulp suspension when trim waste is recycled. Material loss due to evaporation during laser cutting and amount of solid residues after cutting were evaluated. Edge trimming with laser would result in 0.25 kg/h of solid residues and 2.5 kg/h of lost material due to evaporation. Schemes of laser cutting implementation and needed laser equipment were discussed. Generally, laser cutting system would require two laser sources (one laser source for each cutting zone), set of beam transfer and focusing optics and cutting heads. In order to increase reliability of system, it was suggested that each laser source would have double capacity. That would allow to perform cutting employing one laser source working at full capacity for both cutting zones. Laser technology is in required level at the moment and do not require additional development. Moreover, capacity of speed increase is high due to availability high power laser sources what can support the tendency of speed increase of paper making machines. Laser cutting system would require special roll to maintain cutting. The scheme of such roll was proposed as well as roll integration into paper making machine. Laser cutting can be done in location of central roll in press section, before so-called open draw where many web breaks occur, where it has potential to improve runability of a paper making machine. Economic performance of laser cutting was done as comparison of laser cutting system and water jet cutting working in the same conditions. It was revealed that laser cutting would still be about two times more expensive compared to water jet cutting. This is mainly due to high investment cost of laser equipment and poor energy efficiency of CO2 lasers. Another factor is that laser cutting causes material loss due to evaporation whereas water jet cutting almost does not cause material loss. Despite difficulties of laser cutting implementation in paper making machine, its implementation can be beneficial. The crucial role in that is possibility to improve cut edge strength properties and consequently reduce number of web breaks. Capacity of laser cutting to maintain cutting speeds which exceed current speeds of paper making machines what is another argument to consider laser cutting technology in design of new high speed paper making machines.

Sperrin Lakeland Trust - Consultation Paper: Making Services Safer In Sperrin Lakeland Trust

Sperrin Lakeland Trust - Consultation Paper: Making Services Safer In Sperrin Lakeland Trust

The art of paper-making : a practical handbook of the manufacture of paper from rags, esparto, straw, and other fibrous materials, including the manufacture of pulp from wood fibre, with a description of the machinery and appliances used, to which are added details of processes for recovering soda from waste liquors /

Printed in Great Britain.

The cellulose-water relationship in paper-making,

Mode of access: Internet.

The sister arts; or, A concise and interesting view of the nature and history of paper-making, printing, and bookbinding ...

Mode of access: Internet.

Continuous phase synchronised drives (for a rod-making machine)

Traditional high speed machinery actuators are powered and coordinated by mechanical linkages driven from a central drive, but these linkages may be replaced by independently synchronised electric drives. Problems associated with utilising such electric drives for this form of machinery were investigated. The research concentrated on a high speed rod-making machine, which required control of high inertias (0.01-0.5kgm2), at continuous high speed (2500 r/min), with low relative phase errors between two drives (0.0025 radians). Traditional minimum energy drive selection techniques for incremental motions were not applicable to continuous applications which require negligible energy dissipation. New selection techniques were developed. A brushless configuration constant enabled the comparison between seven different servo systems; the rate earth brushless drives had the best power rates which is a performance measure. Simulation was used to review control strategies, such that a microprocessor controller with a proportional velocity loop within a proportional position loop with velocity feedforward was designed. Local control schemes were investigated as means of reducing relative errors between drives: the slave of a master/slave scheme compensates for the master's errors: the matched scheme has drives with similar absolute errors so the relative error is minimised, and the feedforward scheme minimises error by adding compensation from previous knowledge. Simulation gave an approximate velocity loop bandwidth and position loop gain required to meet the specification. Theoretical limits for these parameters were defined in terms of digital sampling delays, quantisation, and system phase shifts. Performance degradation due to mechanical backlash was evaluated. Thus any drive could be checked to ensure that the performance specification could be realised. A two drive demonstrator was commissioned with 0.01kgm2 loads. By use of simulation the performance of one drive was improved by increasing the velocity loop bandwidth fourfold. With the master/slave scheme relative errors were within 0.0024 radians at a constant 2500 r/min for two 0.01 kgm^2 loads.

Simulating the performance of paper machine control

The topic of this thesis is the simulation of a combination of several control and data assimilation methods, meant to be used for controlling the quality of paper in a paper machine. Paper making is a very complex process and the information obtained from the web is sparse. A paper web scanner can only measure a zig zag path on the web. An assimilation method is needed to process estimates for Machine Direction (MD) and Cross Direction (CD) profiles of the web. Quality control is based on these measurements. There is an increasing need for intelligent methods to assist in data assimilation. The target of this thesis is to study how such intelligent assimilation methods are affecting paper web quality. This work is based on a paper web simulator, which has been developed in the TEKES funded MASI NoTes project. The simulator is a valuable tool in comparing different assimilation methods. The thesis contains the comparison of four different assimilation methods. These data assimilation methods are a first order Bayesian model estimator, an ARMA model based on a higher order Bayesian estimator, a Fourier transform based Kalman filter estimator and a simple block estimator. The last one can be considered to be close to current operational methods. From these methods Bayesian, ARMA and Kalman all seem to have advantages over the commercial one. The Kalman and ARMA estimators seems to be best in overall performance.

Offset-print mottling measurement using machine vision

Mottling is one of the key defects in offset-printing. Mottling can be defined as unwanted unevenness of print. In this work, diameter of a mottle spot is defined between 0.5-10.0 mm. There are several types of mottling, but the reason behind the problem is still not fully understood. Several commercial machine vision products for the evaluation of print unevenness have been presented. Two of these methods used in these products have been implemented in this thesis. The one is the cluster method and the other is the band-pass method. The properties of human vision system have been taken into account in the implementation of these two methods. An index produced by the cluster method is a weighted sum of the number of found spots, and an index produced by band-pass method is a weighted sum of coefficients of variations of gray-levels for each spatial band. Both methods produce larger indices for visually poor samples, so they can discern good samples from the poor ones. The difference between the indices for good and poor samples is slightly larger produced by the cluster method. 11 However, without the samples evaluated by human experts, the goodness of these results is still questionable. This comparison will be left to the next phase of the project.

Natural and synthetic fibres improving tensile strength and elongation of paper products

The theory part of the Master’s thesis introduces fibres with high tensile strength and elongation used in the production of paper or board. Strong speciality papers are made of bleached softwood long fibre pulp. The aim of the thesis is to find new fibres suitable for paper making to increase either tensile strength, elongation or both properties. The study introduces how fibres bond and what kind of fibres give the strongest bonds into fibre matrix. The fibres that are used the in manufacturing of non-wovens are long and elastic. They are longer than softwood cellulose fibres. The end applications of non-wovens and speciality papers are often the same, for instance, wet napkins or filter media. The study finds out which fibres are used in non-wovens and whether the same fibres could be added to cellulose pulp as armature fibres, what it would require for these fibres to be blended in cellulose, how they would bind with cellulose and whether some binding agents or thermal bonding, such as hot calendaring would be necessary. The following fibres are presented: viscose, polyester, nylon, polyethylene, polypropylene and bicomponent fibres. In the empiric part of the study the most suitable new fibres are selected for making hand sheets in laboratory. Test fibres are blended with long fibre cellulose. The test fibres are viscose (Tencel), polypropylene and polyethylene. Based on the technical values measured in the sheets, the study proposes how to continue trials on paper machine with viscose, polyester, bicomponent and polypropylene fibres.

Ontario Paper Company Limited

On February 29, 1912 The Ontario Paper Company Limited was incorporated under the leadership of Col. Robert R. McCormick. Four months later construction began in Thorold, Ontario as this location was best for the abundance of power and water and water transportation. The first machine was started at the mill on September 5, 1913. The mill was one of the most advanced of its era, using electricity instead of water power. The mill was also the first of its kind as it combined pulp and paper making instead of separating the two operations.

Verification of a dynamic laboratory scale former

Laboratoriomittakaavainen formeri on välttämätön, jotta paperinvalmistusprosessin jäljitteleminen olisi mahdollista. Vaikka erilaisia formereita löytyykin paperiteollisuudesta, tilaa on kuitenkin laboratoriomittakaavaiselle paperinvalmistusmenetelmälle, joka sijoittuisipilottikoneen ja perinteisen laboratorioarkkimuotin välille. Formeri, jolla saadaan aikaiseksi oikean paperinvalmistuksen kaltaiset olosuhteet ja ilmiöt on kehitetty, ja sen toiminta on testattu Nalcon Papermaking Centreof Excellence:ssä Espoossa. Formeri on yhdistetty Nalcon lähestymisjärjetelmäsimulaattoriin ja simulaattorilla aikaansaadut hydro-kemialliset ilmiöt voidaan testata nyt myös arkeista. Laitteessa on perälaatikko ja viiraosa. Perälaatikosta massa virtaa viiralle, joka liikkuu eteenpäin hihnakuljettimen hihnojen päällä. Suihku-viira -suhdetta voidaan muuttaa joko muuttamalla virtausnopeutta tai viiran nopeutta tai säätämällä perälaatikon huuliaukkoa. Formerintoiminnan testaus osoitti, että se toimii teknisesti hyvin ja tulokset ovat toistettavia ja loogisia. Arkeissa kuidut ovat orientoituneet, formaatio ja vetolujuussuhde KS/PS riippuvat voimakkaasti suihku-viira -suhteesta, kuten oikeillakinpaperikoneilla.

Hapettavan BIMODES-mikrobientorjuntamenetelmän vaikutukset paperikoneella

The aim of this study was to examine the effects of oxidising BIMODES microbiological control program on three paper machine process. The chemicals used in BIMODES program are sodium hypochlorite (NaOCl) and bromo-chloro-di-methyl-hydantoin (BCDMH). The literary part of this study discusses the microbiological problems in paper making industry, describes functional mechanisms of oxidants and also introduces the BIMODES- program. In the experimental part the aim was to examine the effects of BIMODES in three different paper machines. The purpose was to find out the effects and changes in wet end chemistry, bacterial counts, in the other additives and also in the sheet defects and holes. The study also examines what are the most important measurements to control BIMODES dosing. In addition the optimal dosing level for each machine was tried to find out. It was found that there is a clear correlation between the total chlorine level and bacterial counts. Changes in the BIMODES dosing level can be measured by redox potential, but the correlation is very poor. BIMODES program doesn’t have straight influence to pH values, but if dosage level is too low the bacterial activity can affect degreasing in the pH value. In this study couldn’t find any consequential effects for the other additives by using BIMODES. In addition the optimal dosing levels were found and by following correct halogen levels it is possible to decrease bacterial levels for very low level.

Päällystävän paperikoneen vesikiertojen mallinnus

Työssä mallinnettiin kevyesti päällystettyjä aikakauslehtipapereita valmistavan paperikoneen vesikierrot Balas-ohjelman avulla. Mallin avulla selvitettiin paperikoneelle suunniteltujen muutosten vaikutuksia haitallisten aineiden tasoihin, muihin mallinnettuihin parametreihin ja vedenkulutukseen. Mallin luotettavuutta testattiin käytännössä tehdyillä muutoksilla. Vesinäytteistä haitallisina aineina tarkasteltiin lipofiilisten uuteaineiden, kalsiumin, alumiinin, raudan, piin ja sulfaatin pitoisuuksia. Pohjapaperinäytteistä määritettiin lipofiilisten uuteaineiden sekä kalsiumin ja alumiinin pitoisuudet. Paperikoneelle suunniteltuja muutoksia olivat kiekkosuodattimien kirkkaan suodoksen käyttö viiraosan suihkuvetenä ja päällystyksen yhteydessä syntyvän pastajätteen käyttö pohjapaperin täyteaineena. Kirkkaan suodoksen käytön lisäämisellä pyrittiin vähentämään raakaveden käyttöä. Pastajäte sisältää arvokkaita raaka-aineita, jotka kannattaisi hyödyntää paperitehtaalla. Nykyisin pastajäte kuljetetaan läjitysalueelle. Balas-mallin todettiin mallintavan melko luotettavasti liuenneiden haitallisten aineiden pitoisuuksien sekä muista parametreista muun muassa sakeuden ja tuhkapitoisuuden muutoksia. Pastajätteen palautuksen mallinnuksessa haitallisten aineiden pitoisuudet laskivat prosessissa. Tämä toteutui koeajossa, koska jätepastasta suurin osa oli vettä, joka huuhtoi prosessia. Kirkkaan suodoksen käyttö suihkuvetenä ei nostanut epäorgaanisten haitallisten aineiden pitoisuuksia niin paljon kuin malli ennusti. Todennäköisesti haitalliset aineet saostuivat tai poistuivat tuotteen mukana prosessista. Kirkassuodos-koeajon aikana otetussa pohjapaperinäytteessä kiinteän kalsiumin pitoisuus oli 40 % ja kiinteän alumiinin pitoisuus 11 % korkeampi mutta uuteaineiden pitoisuus 20 % alhaisempi kuin referenssipohjapaperissa.

Data communication in paper sales environment

Tämä diplomityö kirjoitettiin UPM- Kymmene konsernin UPM Net Services sa/nv osastolle Brysselissä ja Helsingissä. Työn aihe, Data communication in paper sales environment, määriteltiin käsittelemään paperin myyntijärjestelmään liittyviä aiheita. Nykyinen paperin myyntijärjestelmä on käsitelty ensin teoriassa ja aiheeseen kuuluvat ohjelmistotuotteet ja työkaluohjelmistot on esitelty. Parannuksia nykyiseen järjestelmään on pohdittu ohjelmistosuunnittelun, tehokkuuden, tiedon hallinnan, tietoturvallisuuden ja liiketoiminnan näkökulmista. Diplomityön käytännön osuudessa esitellään kaksi ohjelmistoa. Nämä ohjelmistot tehtiin UPM Net Services'lle, jotta saatiin kokemuksia viestin välitykseen perustuvasta tiedon siirrosta. Diplomityön johtopäätösosuudessa todetaan, että paperin myyntijärjestelmän tiedon siirto toimii luotettavasti nykyisessä järjestelmässä. Tulevaisuuden tarpeet ja parannukset ovat kuitenkin vaikeasti toteutettavissa nykyään käytettävin välinein. Erityisesti internetin hyödyntäminen nähdään tärkeänä, mutta se on vaikeasti otettavissa käyttöön nykyisessä järjestelmässä. Viestin välitykseen perustuvat järjestelmät ovat osoittautuneet käytännössä toimiviksi ja tärkein kehitysehdotus onkin viestin välitysjärjestelmän käyttöönotto.

Syöttöjännitteen jännitehäiriöt paperikoneen sähkökäytössä

Diplomityön tavoitteena oli selvittää paperikonelinjakäyttöjen toimintaa syöttöjännitteen alenemien ja –jännitekatkojen aikana. Työssä haluttiin selvittää, millaisista häiriöistä laitteistot selviävät pysähtymättä ja kuinka laitteistojen immuniteettia häiriöille voitaisiin parantaa. Standardien esittämien jännitehäiriöiden siedon vaatimuksien lisäksi haluttiin selvittää olosuhteet, joissa asiakkaiden sähkökäytöt tulisi toimia. Näiden ongelmien ratkaisemiseksi selvitettiin laboratoriomittauksin tyristori- ja ISU –syöttöyksiköillä varustettujen linjakäyttöjen testilaitteistojen ominaisuuksia jännitteen alenemien aikana. Lisäksi selvitettiin paperikoneen muiden laitteistojen toimintaa jännitehäiriöiden aikana. Avain sähkökäyttöjen jännitehäiriöiden siedon parantamiseksi löytyy ulkoisista energiavarastoista ja paperikoneen linjakäyttöjen hallitusta ohjaamisesta häiriöiden aikana. Näiden hyödyntäminen edellyttää kuitenkin työssä selvitetyn paperiprosessin ohjauksen tuntemista ratakatkon aikana.