Optical behaviour of cholesteric blue phases in electric fields

The optical behaviour of cholesteric mixtures of negative dielectric anisotrony under electric fields is reported. A mixture of S 311~ (31.35 %) + N 5 was employed. AC voltages (f = 1000 Hz) betweeen 0 and 150 volts were applied. Cells 23 micron thick, with internal SnO2 electrodes, were used.

SrZrO3 powders obtained by chemical method: Synthesis, characterization and optical absorption behaviour

Strontium zirconate (SrZrO3) powders have been synthesized by the polymeric precursor method after heat treatment at different temperatures for 2 h in oxygen atmosphere. The decomposition of precursor powder was followed by thermogravimetric analysis, X-ray diffraction (XRD) and Fourier transform Raman (FT-Raman). The UV-vis absorption spectroscopy measurements suggested the presence of intermediary energy levels in the band gap of structurally disordered powders. XRD, Rietveld refinement and FT-Raman revealed that the powders are free of secondary phases and crystallizes in the orthorhombic structure. (C) 2007 Elsevier Masson SAS. All rights reserved.

Temperature Insensitivity of Optical Properties of InAs/GaAs Quantum Dots due to a Pregrown InGaAs Quantum Well

Both the peak position and linewidth in the photoluminescence spectrum of the InAs/GaAs quantum dots usually vary in an anomalous way with increasing temperature. Such anomalous optical behaviour is eliminated by inserting an In0.2Ga0.8As quantum well below the quantum dot layer in molecular beam epitaxy. The insensitivity of the photoluminescence spectra to temperature is explained in terms of the effective carrier redistribution between quantum dots through the In0.2Ga0.8As quantum well.

Designed ultrafast optical nonlinearity in a plasmonic nanorod metamaterial enhanced by nonlocality

All-optical signal processing enables modulation and transmission speeds not achievable using electronics alone(1,2). However, its practical applications are limited by the inherently weak nonlinear effects that govern photon-photon interactions in conventional materials, particularly at high switching rates(3). Here, we show that the recently discovered nonlocal optical behaviour of plasmonic nanorod metamaterials(4) enables an enhanced, ultrafast, nonlinear optical response. We observe a large (80%) change of transmission through a subwavelength thick slab of metamaterial subjected to a low control light fluence of 7 mJ cm(-2), with switching frequencies in the terahertz range. We show that both the response time and the nonlinearity can be engineered by appropriate design of the metamaterial nanostructure. The use of nonlocality to enhance the nonlinear optical response of metamaterials, demonstrated here in plasmonic nanorod composites, could lead to ultrafast, low-power all-optical information processing in subwavelength-scale devices.

Correlation Between the Electrical and Optical Properties of an Atmospheric Pressure Plasma During Siloxane Coating Deposition

The effect of varying process parameters on atmospheric plasma characteristics and properties of nanometre thick siloxane coatings is investigated in a reel-to-reel deposition process. Varying plasma operation modes were observed with increasing applied power for helium and helium/oxygen plasmas. The electrical and optical behaviour of the dielectric barrier discharge were determined from current/voltage, emission spectroscopy and time resolved light emission measurements. As applied power increased, multiple discharge events occurred, producing a uniform multi-peak pseudoglow discharge, resulting in an increase in the discharge gas temperature. The effects of different operating modes on coating oxidation and growth rates were examined by injecting hexamethyldisiloxane liquid precursor into the chamber under varying operating conditions. A quenching effect on the plasma was observed, causing a decrease in plasma input power and emission intensity. Siloxane coatings deposited in helium plasmas had a higher organic component and higher growth rates than those deposited in helium/oxygen plasmas.

The tautomerism, solvatochromism and non-linear optical properties of fluorescent 3-hydroxyquinoxaline-2-carboxalidine-4-aminoantipyrine

The Schiff base, 3-hydroxyquinoxaline-2-carboxalidine-4-aminoantipyrine, was synthesized by the condensation of 3-hydroxyquinoxaline-2-carboxaldehyde with 4-aminoantipyrine. HPLC, FT-IR and NMR spectral data revealed that the compound exists predominantly in the amide tautomeric form and exhibits both absorption and fluorescence solvatochromism, large stokes shift, two electron quasireversible redox behaviour and good thermal stability, with a glass transition temperature of 104oC. The third-order non-linear optical character was studied using open aperture Z-scan methodology employing 7 ns pulses at 532 nm. The third-order non-linear absorption coefficient, b, was 1.48 x 10-6 cm W-1 and the imaginary part of the third-order non-linear optical susceptibility, Im c(3), was 3.36 x10-10 esu. The optical limiting threshold for the compound was found to be 340 MW cm-2.

The tautomerism, solvatochromism and non-linear optical properties of fluorescent 3-hydroxyquinoxaline-2-carboxalidine-4-aminoantipyrine

The Schiff base, 3-hydroxyquinoxaline-2-carboxalidine-4-aminoantipyrine, was synthesized by the condensation of 3-hydroxyquinoxaline-2-carboxaldehyde with 4-aminoantipyrine. HPLC, FT-IR and NMR spectral data revealed that the compound exists predominantly in the amide tautomeric form and exhibits both absorption and fluorescence solvatochromism, large stokes shift, two electron quasireversible redox behaviour and good thermal stability, with a glass transition temperature of 104 oC. The third-order non-linear optical character was studied using open aperture Z-scan methodology employing 7 ns pulses at 532 nm. The third-order non-linear absorption coefficient, b, was 1.48 x 10-6 cm W-1 and the imaginary part of the third-order non-linear optical susceptibility, Im c(3), was 3.36x10-10 esu. The optical limiting threshold for the compound was found to be 340 MW cm-2.

Investigations of Nonlinear Optical Properties of certain organic photonic materials using Z-Scan and DFWM techniques

Nonlinear optical processes in organic compounds have attracted considerable interest in the field of science and technology because of their compelling technological promises in fields of optical communication,computing,switching and signal processing.As a result of the synthesis of novel organic compounds with varying degree of nonlinear optical strength, many practical devices based on these are getting realised giving new theoretical insights into the nonolinear optical behaviour of materials.Organic compounds like phthalocyanines and porphyrins have evoked great deal of interest in the field of photonic technology.The present thesis describes the results obtained from the investigations carried out on the nonlinear optical properties of certain organo-metallic compounds using Z-Scan and DFWM techniques.

The effect of ionic Co presence on the structural, optical and photocatalytic properties of modified cobalt–titanate nanotubes

With the aim of producing materials with enhanced optical and photocatalytic properties, titanate nanotubes (TNTs) modified by cobalt doping (Co-TNT) and by Na+ -> Co ion-exchange (TNT/Co) were successfully prepared by a hydrothermal method. The influence of the doping level and of the cobalt position in the TNT crystalline structure was studied. Although no perceptible influence of the cobalt ion position on the morphology of the prepared titanate nanotubes was observed, the optical behaviour of the cobalt modified samples is clearly dependent on the cobalt ions either substituting the Ti4+ ions in the TiO6 octahedra building blocks of the TNT structure (doped samples) or replacing the Na+ ions between the TiO6 interlayers (ion-exchange samples). The catalytic ability of these materials on pollutant photodegradation was investigated. First, the evaluation of hydroxyl radical formation using the terephthalic acid as a probe was performed. Afterwards, phenol, naphthol yellow S and brilliant green were used as model pollutants. Anticipating real world situations, photocatalytic experiments were performed using solutions combining these pollutants. The results show that the Co modified TNT materials (Co-TNT and TNT/Co) are good catalysts, the photocatalytic performance being dependent on the Co/Ti ratio and on the structural metal location. The Co(1%)-TNT doped sample was the best photocatalyst for all the degradation processes studied.

Structure and composition related properties of titania thin films

The dependence of optical constants, structure and composition of titania thin films on the process parameters has been investigated. Films were deposited using both reactive electron beam evaporation and ion Assisted Deposition(IAD). If has been observed that the refractive index of IAD films is higher than that for the reactively deposited films, without much difference in the extinction coefficient. Electron paramagnetic resonance has been used to estimate qualitatively the presence of non-stoichiometry in the films. It has been found that these spectra correlate very well the optical behaviour of the films. X-ray diffraction studies revealed that the neutral oxygen deposited films were stress free, while the IAD films showed tensile stress. The lattice parameters showed anisotropic change with ion beam parameters.

Effect of ultrasonic treatment on surface crystallization of calcium bismuth borate glasses

Transparent glasses in CaO-Bi2O3-B2O3 system were fabricated via the conventional melt-quenching technique. X-ray powder diffraction (XRD) and differential thermal analysis (DTA) carried out on the as-quenched samples confirmed their amorphous and glassy nature respectively. The surface crystallization behaviour of these glasses with and without ultrasonic surface treatment (UST) was monitored using XRD, optical microscopy and scanning electron microscopy (SEM). The volume fraction, depth of crystallization and the (001) orientation factor for the heat treated samples with and without UST were compared. The ultrasonically-treated samples on subsequent heat treatment were found to crystallize at lower temperatures associated with the highest degree of orientation factor (0.95) in contrast with those of non-UST samples. These surface crystallized glasses were found to exhibit nonlinear optical behaviour emitting green light (532 nm) when they were exposed to the infrared radiation (1064 nm) using Nd:YAG laser.

Métodos químicos de modificação superficial de nanomateriais

O objectivo geral desta tese foi investigar diversas estratégias de síntese de nanocompósitos híbridos de matriz polimérica, contendo nanopartículas inorgânicas com funcionalidades diversas. O interesse nestes nanocompósitos multifuncionais consiste no enorme potencial que apresentam para novas aplicações tecnológicas, tais como em optoelectrónica ou em medicina. No capítulo introdutório, apresenta-se uma revisão das propriedades de nanopartículas inorgânicas e nanoestruturas obtidas a partir destas, métodos de preparação e de modificação química superficial, incluindo a formação de nanocompósitos poliméricos, bem como a aplicação destas nanoestruturas em medicina e biologia. O estudo das propriedades de nanopartículas de ouro é um importante tema em Nanociência e Nanotecnologia. As propriedades singulares destas NPs apresentam uma estreita relação com o tamanho, morfologia, arranjo espacial e propriedades dieléctricas do meio circundante. No capítulo 2, é reportada a preparação de nanocompósitos utilizando miniemulsões de poli-estireno (PS) e poli-acrilato de butilo (PBA) contendo nanopartículas de ouro revestidas com moléculas orgânicas. As propriedades ópticas destas estruturas híbridas são dominadas por efeitos plasmónicos e dependem de uma forma crítica na morfologia final dos nanocompósitos. Em particular, demonstra-se aqui a possibilidade de ajustar a resposta óptica, na região do visível do espectro, através do arranjo das nanopartículas na matriz polimérica, e consequentemente o acoplamento plasmónico, utilizando nanopartículas resultantes da mesma síntese. Na generalidade, é reportada aqui uma estratégia alternativa para modificar a resposta óptica de nanocompósitos, através do controlo da morfologia do compósito final face à estratégia mais comum que envolve o controlo das características morfológicas das partículas metálicas utilizadas como materiais de partida. No Capítulo 3 apresentam-se os resultados da preparação de vários compósitos poliméricos com propriedades magnéticas de interesse prático. Em particular discute-se a síntese e propriedades magnéticas de nanopartículas de ligas metálicas de cobalto-platina (CoPt3) e ferro-platina (FePt3), assim como de óxidos de ferro (magnetite Fe3O4 e maguemite g-Fe2O3) e respectivos nanocompósitos poliméricos. A estratégia aqui descrita constitui uma via interessante de desenvolver materiais nanocompósitos com potencial aplicação em ensaios de análise de entidades biológicas in vitro, que pode ser estendido a outros materiais magnéticos. Como prova de conceito, demonstrase a bioconjugação de nanocompósitos de CoPt3/PtBA com anticorpos IgG de bovino. No capítulo 4 é descrita a preparação e propriedades ópticas de pontos quânticos (“quantum dots”, QDs) de CdSe/ZnS assim como dos seus materiais nanocompósitos poliméricos, CdSe/ZnS-PBA. Como resultado das suas propriedades ópticas singulares, os QDs têm sido extensivamente investigados como materiais inorgânicos para aplicações em dispositivos ópticos. A incorporação de QDs em matrizes poliméricas é de particular interesse, nomeadamente devido ao comportamento óptico do nanocompósito final parecer estar dependente do tipo de polímero utilizado. As propriedades ópticas dos nanocompósitos foram estudadas sistematicamente por medidas de fotoluminescência. Os nanocompósitos apresentam propriedades interessantes para potenciais aplicações biológicas em diagnóstico in vitro, funcionando como sondas biológicas luminescentes.

Mikrostrukturierte Sensoren für die pH-Wert-Bestimung auf Basis von dünnen, intrinisch leitfähigen Polyanilinschichten

Der pH-Wert stellt in der Chemie, Physik, Biologie, Pharmazie und Medizin eine wichtige Meßgröße dar, da eine Vielzahl von Reaktionen durch den pH-Wert bestimmt wird. In der Regel werden zur pH-Wert-Messung Glaselektroden eingesetzt. Hierbei konnte der pH-sensitive Bereich zwar bis auf einige Mikrometer reduziert werden, aber die Gesamtab-messungen betragen immer noch 15-20 cm. Mit der Einführung miniaturisierter Reaktionsgefäße ist daher der Bedarf an miniaturisierten Sensoren enorm gestiegen. Um in solchen Gefäßen Reaktionsparameter wie z. B. den pH-Wert zu kontrollieren, müssen die Gesamtabmessungen der Sensoren verringert werden. Dies lässt sich mit Hilfe der Mikrostrukturtechnik von Silizium realisieren. Hiermit lassen sich Strukturen und ganze Systeme bis in den Nanometerbereich herstellen. Basierend auf Silizium und Gold als Elektrodenmaterial wurden im Rahmen dieser Arbeit verschiedene Interdigitalstrukturen hergestellt. Um diese Strukturen zur pH-Wert-Messungen einsetzen zu können, müssen sie mit einer pH-sensitiven Schicht versehen werden. Hierbei wurde Polyanilin, ein intrinsisch leitendes Polymer, aufgrund seine pH-abhängigen elektrischen und optischen Verhaltens eingesetzt. Die Beschichtung dieser Sensoren mit Polyanilin erfolgte vorwiegend elektrochemisch mit Hilfe der Zyklovoltammetrie. Neben der Herstellung reiner Polyanilinfilme wurden auch Kopolymerisationen von Anilin und seinen entsprechenden Aminobenzoesäure- bzw. Aminobenzensulfonsäurederivaten durchgeführt. Ergebnisse dazu werden vorgestellt und diskutiert. Zur Charakterisierung der resultierenden Polyanilin- und Kopolymerfilme auf den Inter-digitalstrukturen wurden mit Hilfe der ATR-FT-IR-Spektroskopie Spektren aufgenommen, die gezeigt und diskutiert werden. Eine elektrochemische Charakterisierung der Polymere erfolgte mittels der Zyklovoltammetrie. Die mit Polyanilin bzw. seinen Kopolymeren beschichteten Sensoren wurden dann für Widerstandsmessungen an den Polymerfilmen in wässrigen Medien eingesetzt. Polyanilin zeigt lediglich eine pH-Sensitivität in einem pH-Bereich von pH 2 bis pH 4. Durch den Einsatz der Kopolymere konnte dieser pH-sensitive Bereich jedoch bis zu einem pH-Wert von 10 ausgeweitet werden. Zur weiteren Miniaturisierung der Sensoren wurde das Konzept der interdigitalen Elektroden-paare auf Cantilever übertragen. Die pH-sensitive Zone konnte dabei auf 500 µm2 bei einer Gesamtlänge des Sensors (Halter mit integriertem Cantilever) von 4 mm reduziert werden. Neben den elektrischen pH-abhängigen Eigenschaften können auch die optischen Eigen-schaften des Polyanilins zur pH-Detektion herangezogen werden. Diese wurden zunächst mit Hilfe der UV-VIS-Spektroskopie untersucht. Die erhaltenen Spektren werden gezeigt und kurz diskutiert. Mit Hilfe eines Raster-Sonden-Mikroskops (a-SNOM, Firma WITec) wurden Reflexionsmessungen an Polyanilinschichten durchgeführt. Zur weiteren Miniaturisierung wurden Siliziumdioxidhohlpyramiden (Basisfläche 400 µm2) mit Spitzenöffnungen in einem Bereich von 50-150 nm mit Polyanilin beschichtet. Auch hier sollten die optischen Eigenschaften des Polyanilins zur pH-Wert-Sensorik ausgenutzt werden. Es werden erste Messungen an diesen Strukturen in Transmission diskutiert.

Entwicklung neuartiger stickstoffreicher Polyphenylene

Im Rahmen dieser Arbeit wurden Darstellung und elektronische Anwendungsmöglichkeiten von neuartigen stickstoff- und damit elektronenreichen Poly(para-phenylenen) untersucht. Der Teilbereich „Polycarbazole“ befasst sich mit der Synthese von konjugierten (Stufen)leiterpolymeren auf der Basis von Carbazol. Dazu wurde ein neuer und effizienter Syntheseweg zur Gewinnung von 2,7-Dibromcarbazol entwickelt. Durch die weitere Funktionalisierung von 2,7-Dibromcarbazol gelang es, elektronenreiche Leiterpolymere zu gewinnen, die eine grüne Emissionsfarbe aufwiesen. Mit der Verwendung von R = 2-Decyltetradecyl als löslichkeitsfördernder Seitenkette in einem Poly(2,7-carbazol) konnte erstmals ein hochmolekulares Polycarbazol gewonnen werden. Dieses gut lösliche Poly(2,7-carbazol) erwies sich als ein exzellentes Donatormaterial in Solarzellen, welches in Kombination mit dem Farbstoff PDI eine effiziente Solarzelle ergab. Eine OLED mit einem neuartigen arylierten Polycarbazol als Emittermaterial zeigte eine sehr niedrige Turn-on-Spannung und eine intensive blaue EL-Emission. Das Kapitel über imidazolhaltige Poly(para-phenylene) und Discoten stellt die Darstellung von planarisierten Bisimidazolen vor, welche in hohen Ausbeuten durch eine intramolekulare Buchwald-Reaktion zwischen den Imidazolringen und der zentralen Terphenyleinheit durchgeführte wurde. Die dreistufige Darstellung der Discoten aus einem Terephthalaldehyd-Derivat und einem Benzil erlaubt eine einfache sowie variable Einführung von löslichkeitsfördernden Alkylsubstituenten. Auf diese Weise ist der Zugang zu einer völlig neuartigen Klasse an discotischen Materialien möglich, die eine Kombination aus Discoten auf der Basis von Benzolringen (wie z.B. HBC) mit Heteroaromaten darstellen. Die gewonnenen scheibenförmigen Bisimidazole wiesen dementsprechend auf Selbstanordnung zurückzuführende kolumnare Anordnungen und hexagonale Überstrukturen auf. Im dritten Themengebiet wird der Einbau eines Phthalimidchromophors direkt in das Rückgrad von Polyanilin vorgestellt. Da jegliche Veränderung des Oxidationsgrades zu einer unterschiedlichen Donatorfähigkeit des Polyanilinhauptkette führt, variiert in Abhängigkeit davon das Absorptionsverhalten des eingebauten Farbstoffes. Durch die Einführung des Phthalimidchromophores war es zudem möglich, ein leitfähiges Polymer zu erhalten, das im Gegensatz zum nicht-fluoreszierenden Polyanilin eine intensive gelbe Fluoreszenz (lmax = 547 nm) aufweist.