Particle size and concentration of poly(epsilon-caprolactone) and adipate modified starch blend on mineralization in soils with differing textures

The objective of this study was to evaluate the effect of particle size and concentration of poly(F.-caprolactone) and adipate modified starch blend on mineralization in soils with differing textures, comparing it with polyethylene under the same experimental conditions. Two soil types were used: a Kandiudalfic Eutrudox with a clayey texture and an Arenic Hapludult with a sandy texture. The two different plastic specimens were incorporated in the form of plastic films with three increasing particle sizes and six doses, from 0 to 2.5 mg C g(-1) soil. Each plastic dose was incorporated into 200 g of soil placed in a hermetically closed jar at 28 degrees C, and incubated for a 120-day period to determine CO(2) evolution. Once again it was confirmed that polyethylene is almost non-biodegradable, in contrast to PCL/S, which can be defined as a biodegradable material. Soil texture affected the mineralization kinetics of the plastic specimens, with higher values for the clayey soil. No changes in soil microbial biomass-C or -N were observed by adding polyethylene and PCL/S to the soil. Also, no significant differences were observed on seed emergence and development of rice seedlings (Oryza sativa L.) in plastic modified soil. (C) 2009 Elsevier Ltd. All rights reserved.

Mineralization of poly(epsilon-caprolactone)/adipate modified starch blend in agricultural soil

The biodegradability properties of poly(epsilon-caprolactone) (PCL) and modified adipate-starch (AS) blends, using Edenol-3203 (E) as a starch plasticizer, were investigated in laboratory by burial tests of the samples in previously analyzed agricultural soil. The biodegradation process was carried out using the respirometric test according to ASTM D 5988-96, and the mineralization was followed by both variables such as carbon dioxide evolution and mass loss. The results indicated that the presence of AS-E accelerated the biodegradation rate as expected.

Stability of curcumin microencapsulated by spray and freeze drying in binary and ternary matrices of maltodextrin, gum arabic and modified starch

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Freeze-drying for microencapsulation of turmeric oleoresin using modified starch and gelatin

The aims of this study were to assess the turmeric oleoresin microencapsulation by freeze-drying with modified starch/gelatin and to evaluate its stability during storage at different temperatures and light. Encapsulated turmeric oleoresin w stored at −20, 25 and 60C, in the absence of light, and at 25C in the presence of light, and analyzed over a period of 6 weeks for curcumin and total phenolic contents and color. The different concentrations of wall material showed no significant effect on the curcumin retention. The best conditions for microencapsulation of turmeric oleoresin were: wall material composed of 30 g/100 g of modified starch + 1 g/100 g gelatin and mechanical homogenization. Encapsulated material was more stable during storage at −20C and less stable at 25C in the presence of light.

Microencapsulation of turmeric oleoresin in binary and ternary blends of gum arabic, maltodextrin and modified starch

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Modified broken rice starch as fat substitute in sausages

The demand for low-fat beef products has led the food industry to use fat substitutes such as modified starch. About 14% of broken rice is generated during processing. Nevertheless, this by-product contains high levels of starch; being therefore, great raw material for fat substitution. This study evaluated the applicability of chemically and physically modified broken rice starch as fat substitute in sausages. Extruded and phosphorylated broken rice was used in low-fat sausage formulation. All low-fat sausages presented about 55% reduction in the fat content and around 28% reduction in the total caloric value. Fat replacement with phosphorylated and extruded broken rice starch increased the texture acceptability of low-fat sausages, when compared to low-fat sausages with no modified broken rice. Results suggest that modified broken rice can be used as fat substitute in sausage formulations, yielding lower caloric value products with acceptable sensory characteristics.

Thermal, rheological, and structural behaviors of natural and modified cassava starch granules, with sodium hypochlorite solutions

The use of chemically modified starches is widely accepted in various industries, with several applications. In this research, natural cassava starch granules were treated with standard sodium hypochlorite solution at 0.8, 2.0, and 5.0 g Cl/100 g starch. The native and modified starch samples were investigated by means of the following techniques: simultaneous thermogravimetry-differential thermal analysis, which allowed us to verify the thermal decomposition associated with endothermic or exothermic phenomena; and differential scanning calorimetry that was used to determine gelatinization enthalpy as well as the rapid viscoamylographic analysis that provided the pasting temperature and viscosity. By means of non-contact-atomic force microscopy method and X-ray powder patterns diffractometry, it was possible to observe the surface morphology, topography of starch granules, and alterations in the granules' crystallinity. © 2012 Akadémiai Kiadó, Budapest, Hungary.

Effect of the radiolitic sterilization in polyethylene/starch blends

Samples of LDPE/modified starch blends 80/20 m/m before and after exposure to gamma rays were examined by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction. The effect of gamma radiation is clearly seen in the samples irradiated at a dose of 25 kGy. The main alteration in the polymeric material after exposure at the radiation range was a decrease in the mechanical properties, alterations in the chemical structure of the blend with an increase in the carbonyl and vinyl indices and the appearance of new crystalline symmetry generating a crystalline domain not existing before in the blend.

Microencapsulation of pequi pulp by spray drying: use of modified starches as encapsulating agent

The aim of this study was to evaluate the microencapsulation of pequi pulp by spray drying. A central composite rotational design was used in order to evaluate the effect of the independent variables: inlet air temperature, surfactant concentration and modified starch concentration. The dependent variables were assumed as yield of the process and the product features microencapsulated. A selection of the best process condition was performed to obtain the best condition of a product with the highest vitamin C and carotenoids content. Powders showed moisture content below 2%. The experimental values of hygroscopicity, yield, water activity, total carotenoids and vitamin C powders ranged from 7.96 to 10.67 g of adsorbed water/100g of solids, 24.34 to 49.80%, 0.13 to 0.30, 145.78 to 292.11 mg of ascorbic acid/g of pequi solids and 15.51 to 123.42 mg of carotenoids/g of pequi solids, respectively. The inlet air temperature 140°C, the surfactant concentration of 2.5% and the modified starch concentration of 22.5% was recommended as the selected condition. By the scanning electron microscopy, it was observed that most of the particles had spherical shape and smooth surface.

Starch edible coating of papaya: effect on sensory characteristics

The coating of papayas with Cassava Starch (CS) and carboxymethyl starch (CMS) is an alternative to extend the shelf life of these fruits. This study evaluated the effect of the three different levels of CS and CMS (1, 3, and 5%) on sensory characteristics of papayas during storage. Nine selected and trained assessors evaluated 13 sensory attributes using the Multiple Comparison Test. The appearance and flavor attributes of the papayas treated with CS and CMS were compared to the control or reference sample (R - fruit without coating) using a nine-point scale, which varied from 1: less intense than R; 5: equal to R; 9: more intense than R. The samples were coded with three digit numbers and evaluated with repetition by a panel of assessors. In general, appearance was more affected by the coatings than flavor. Fruits coated with 3 and 5% of both coatings kept the green color longer than the other coating’s concentrations, and at 5% the color of the fruits was less uniform on the last evaluation day. The 3 and 5% CS coating gave greater brightness to the fruits. 5% CMS favored the presence of fungi and damaged the fruit surface at the 14th day of storage. The CS coating at 5% presented peeled surface during all experimental time. Changes in fruits’ flavor were perceived at the 12th and 14th days of storage. A less characteristic flavor and a bitter taste were noticed in the fruits coated with CS and CMS at 5% at the 12th day of storage.

The effect of acid hydrolysis on the technological functional properties of pinhão (Araucaria brasiliensis) starch

Technological functional properties of native and acid-thinned pinhão (seeds of Araucária angustifolia, Brazilian pine) starches were evaluated and compared to those of native and acid-thinned corn starches. The starches were hydrolyzed (3.2 mol.L-1 HCl, 44 ºC, 6 hours) and evaluated before and after the hydrolysis reaction in terms of formation, melting point and thermo-reversibility of gel starches, retrogradation (in a 30-day period and measurements every three days), paste freezing and thawing stability (after six freezing and thawing cycles), swelling power, and solubility. The results of light transmittance (%) of pastes of native and acid-thinned pinhão starches was higher (lower tendency to retrogradation) than that obtained for corn starches after similar storage period. Native pinhão starch (NPS) presented lower syneresis than native corn starch (NCS) when submitted to freeze-thaw cycles. The acid hydrolysis increased the syneresis of the two native varieties under storage at 5 ºC and after freezing and thawing cycles. The solubility of NPS was lower than that of native corn starch at 25, 50, and 70 ºC. However, for the acid-thinned pinhão starch (APS), this property was significantly higher (p < 0.05) when compared to that of acid-thinned corn starch (ACS). From the results obtained, it can be said that the acid treatment was efficient in producing a potential fat substitute from pinhão starch variety, but this ability must be further investigated.

High-amylose carboxymethyl starch matrices for oral sustained drug-release : in vitro and in vivo evaluation

Les amidons non modifiées et modifiés représentent un groupe d’excipients biodégradables et abondants particulièrement intéressant. Ils ont été largement utilisés en tant qu’excipients à des fins diverses dans des formulations de comprimés, tels que liants et/ou agents de délitement. Le carboxyméthylamidon sodique à haute teneur en amylose atomisé (SD HASCA) a été récemment proposé comme un excipient hydrophile à libération prolongée innovant dans les formes posologiques orales solides. Le carboxyméthylamidon sodique à haute teneur en amylose amorphe (HASCA) a d'abord été produit par l'éthérification de l'amidon de maïs à haute teneur en amylose avec le chloroacétate. HASCA a été par la suite séché par atomisation pour obtenir le SD HASCA. Ce nouvel excipient a montré des propriétés présentant certains avantages dans la production de formes galéniques à libération prolongée. Les comprimés matriciels produits à partir de SD HASCA sont peu coûteux, simples à formuler et faciles à produire par compression directe. Le principal objectif de cette recherche était de poursuivre le développement et l'optimisation des comprimés matriciels utilisant SD HASCA comme excipient pour des formulations orales à libération prolongée. A cet effet, des tests de dissolution simulant les conditions physiologiques du tractus gastro-intestinal les plus pertinentes, en tenant compte de la nature du polymère à l’étude, ont été utilisés pour évaluer les caractéristiques à libération prolongée et démontrer la performance des formulations SD HASCA. Une étude clinique exploratoire a également été réalisée pour évaluer les propriétés de libération prolongée de cette nouvelle forme galénique dans le tractus gastro-intestinal. Le premier article présenté dans cette thèse a évalué les propriétés de libération prolongée et l'intégrité physique de formulations contenant un mélange comprimé de principe actif, de chlorure de sodium et de SD HASCA, dans des milieux de dissolution biologiquement pertinentes. L'influence de différentes valeurs de pH acide et de temps de séjour dans le milieu acide a été étudiée. Le profil de libération prolongée du principe actif à partir d'une formulation de SD HASCA optimisée n'a pas été significativement affecté ni par la valeur de pH acide ni par le temps de séjour dans le milieu acide. Ces résultats suggèrent une influence limitée de la variabilité intra et interindividuelle du pH gastrique sur la cinétique de libération à partir de matrices de SD HASCA. De plus, la formulation optimisée a gardé son intégrité pendant toute la durée des tests de dissolution. L’étude in vivo exploratoire a démontré une absorption prolongée du principe actif après administration orale des comprimés matriciels de SD HASCA et a montré que les comprimés ne se sont pas désintégrés en passant par l'estomac et qu’ils ont résisté à l’hydrolyse par les α-amylases dans l'intestin. Le deuxième article présente le développement de comprimés SD HASCA pour une administration orale une fois par jour et deux fois par jour contenant du chlorhydrate de tramadol (100 mg et 200 mg). Ces formulations à libération prolongée ont présenté des valeurs de dureté élevées sans nécessiter l'ajout de liants, ce qui facilite la production et la manipulation des comprimés au niveau industriel. La force de compression appliquée pour produire les comprimés n'a pas d'incidence significative sur les profils de libération du principe actif. Le temps de libération totale à partir de comprimés SD HASCA a augmenté de manière significative avec le poids du comprimé et peut, de ce fait, être utilisé pour moduler le temps de libération à partir de ces formulations. Lorsque les comprimés ont été exposés à un gradient de pH et à un milieu à 40% d'éthanol, un gel très rigide s’est formé progressivement sur leur surface amenant à la libération prolongée du principe actif. Ces propriétés ont indiqué que SD HASCA est un excipient robuste pour la production de formes galéniques orales à libération prolongée, pouvant réduire la probabilité d’une libération massive de principe actif et, en conséquence, des effets secondaires, même dans le cas de co-administration avec une forte dose d'alcool. Le troisième article a étudié l'effet de α-amylase sur la libération de principe actif à partir de comprimés SD HASCA contenant de l’acétaminophène et du chlorhydrate de tramadol qui ont été développés dans les premières étapes de cette recherche (Acetaminophen SR et Tramadol SR). La modélisation mathématique a montré qu'une augmentation de la concentration d’α-amylase a entraîné une augmentation de l'érosion de polymère par rapport à la diffusion de principe actif comme étant le principal mécanisme contrôlant la libération de principe actif, pour les deux formulations et les deux temps de résidence en milieu acide. Cependant, même si le mécanisme de libération peut être affecté, des concentrations d’α-amylase allant de 0 UI/L à 20000 UI/L n'ont pas eu d'incidence significative sur les profils de libération prolongée à partir de comprimés SD HASCA, indépendamment de la durée de séjour en milieu acide, le principe actif utilisé, la teneur en polymère et la différente composition de chaque formulation. Le travail présenté dans cette thèse démontre clairement l'utilité de SD HASCA en tant qu'un excipient à libération prolongée efficace.

Physical characteristics of extruded cassava starch

Considerando a importância do amido de mandioca para as indústrias brasileiras, este trabalho teve por objetivo avaliar os efeitos de parâmetros de extrusão sobre as características físicas e propriedades de pasta do amido de mandioca extrusado. Foi utilizado o delineamento fatorial do tipo central composto rotacional com três variáveis independentes (2³) e a metodologia de superfície de resposta para avaliar os resultados de índice de expansão, volume específico, índice de absorção de água, índice de solubilidade em água, cor e propriedades de pasta, de acordo com as variações de umidade, temperatura de extrusão e rotação da rosca. A temperatura de extrusão influenciou o índice de expansão, volume específico, índice de absorção de água, todos os parâmetros de cor e a viscosidade inicial, pico e viscosidade final. Já a umidade teve influência sobre o volume específico, parâmetros de cor, viscosidade final e tendência a retrogradação. A rotação da rosca teve efeito no índice de absorção de água, nos componentes de cor bem como viscosidade final e na tendência à retrogradação do amido extrusado. Nas condições operacionais de elevada umidade inicial da matéria-prima, baixa rotação da rosca e temperatura de extrusão no nível intermediário ocorreu menor degradação do amido, o que é desejável em amidos pré-gelatinizados.

Effects of acetylation and acetylation-hydroxypropylation (dual-modification) on the properties of starch from Carioca bean (Phaseolus vulgaris L.)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Microencapsulação de óleo essencial de laranja

It was done microencapsulation of natural essencial orange oil through spray-drying. The purpose was to use the best proportion of wall materials among maltodextrin, acacia gum, and modified starch (capsul) in order to retain greater amount of orange oil. The orange oil (10%) and maltodextrin (36%) remained constant. Three spray drying temperatures were employed: 180°C, 200°C and 220°C, therefore, nine final products were obtained. The superficial and inner oil concentrations were measured. The microcapsules were also examined through optical and scanning electron microscopy. The three temperatures employed did not affect the microencapsulation. The microstructure of the capsules were almost similar regardless the proportion employed among the carbohydrates to wall composition. At light microscopy it was observed a great heterogeneity of capsules diameters, and probably not smooth surfaces; at scanning electron microscopy it was clear that the walls displayed porosity over round surfaces. The best retention was given by the formula containing 10% of capsul, 10% of orange oil and 36% of maltodextrin, when total oil retention was 94%, regardless the drying temperature here employed.