Alteração de atributos físicos em latossolo com aplicação superficial de escória de aciaria, lama cal, lodos de esgoto e calcário

Os resíduos industriais e urbanos podem atuar como condicionadores do solo, pois possuem a capacidade de alterar suas propriedades físicas. Contudo, não há referência para os atributos físicos do solo quando esses resíduos são aplicados sobre a superfície do solo no sistema plantio direto. O objetivo deste trabalho foi avaliar o efeito da aplicação superficial de escória de aciaria, lama cal, lodos de esgoto e calcário nos atributos físicos de um Latossolo Vermelho distrófico sob sistema plantio direto. Os tratamentos foram constituídos por quatro resíduos: lodos de esgoto centrifugado - LC e de biodigestor - LB, escória de aciaria - E, e lama cal - Lcal, interagindo com quatro doses (0, 2, 4 e 8 t ha-1, aplicadas na forma seca) mais uma testemunha (controle), constituída da aplicação de 2 t ha-1 de calcário. O delineamento experimental foi em blocos casualizados no esquema fatorial 4 x 4 + 1, com quatro repetições. A presença de Ca na composição de lama cal, lodo de esgoto centrifugado, escória de aciaria e calcário permite o aumento da agregação das partículas, diâmetro médio ponderado, índice de estabilidade de agregados, porosidade e retenção de água, sendo essas alterações distintas para cada fonte, dose e profundidade de reação no solo. A aplicação superficial da lama cal na dose de 8 t ha-1, após 27 meses de reação, proporcionou a maior agregação das partículas no solo, desde a superfície até 40 cm de profundidade.

Resistência tênsil relacionada com atributos de um Latossolo sob sistema de semeadura direta

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Evaluation of Pupillary Diameter in Preschool Children

Few quantitative data exist on pupil diameter, particularly in children. In this article we describe an analysis of pupil diameter and pupil area in normal preschool children during attentive gaze (AG) and spontaneous gaze (SG) using digital imaging. The pupil diameter and pupil area of 200 preschool children aged 4 to 6 years were evaluated. The images were recorded with a digital camera, transferred to a computer, processed by movie software and submitted to the Invert filter of Adobe Photoshop (R) software. Three consecutive measures of pupil diameter and pupil area were taken for both eyes during AG and SG. Arithmetic means of each parameter were calculated and data were expressed in millimeters. Mean pupil diameter was similar for both eyes, presenting values of 4.9 mm during AG and 4.1 mm during SG. Mean pupil area was also similar for both eyes, presenting values of 15.6 mm(2) and 9.1 mm(2) during AG and SG, respectively. There were no differences between boys and girls. However, 6-year-old children showed lower pupil diameter and area under both evaluation conditions.

Polymersomes, smaller than you think : ferrocene as a TEM probe to determine core structure

By incorporating ferrocene into the hydrophobic membrane of PEG-b-PCL polymersome nanoparticles it is possible to selectively visualize their core using Transmission Electron Microscopy (TEM). Two different sizes of ferrocene-loaded polymersomes with mean hydrodynamic diameters of approximately 40 and 90 nm were prepared. Image analysis of TEM pictures of these polymersomes found that the mean diameter of the core was 4–5 times smaller than the mean hydrodynamic diameter. The values obtained also allow the surface diameter and internal volume of the core to be calculated.

Land use effects on soil carbon fractions in the southeastern United States. II. changes in soil carbon fractions along a forest to pasture chronosequence

Since land use change can have significant impacts on regional biogeochemistry, we investigated how conversion of forest and cultivation to pasture impact soil C and N cycling. In addition to examining total soil C, we isolated soil physiochemical C fractions in order to understand the mechanisms by which soil C is sequestered or lost. Total soil C did not change significantly over time following conversion from forest, though coarse (250-2,000 mum) particulate organic matter C increased by a factor of 6 immediately after conversion. Aggregate mean weight diameter was reduced by about 50% after conversion, but values were like those under forest after 8 years under pasture. Samples collected from a long-term pasture that was converted from annual cultivation more than 50 years ago revealed that some soil physical properties negatively impacted by cultivation were very slow to recover. Finally, our results indicate that soil macroaggregates turn over more rapidly under pasture than under forest and are less efficient at stabilizing soil C, whereas microaggregates from pasture soils stabilize a larger concentration of C than forest microaggregates. Since conversion from forest to pasture has a minimal impact on total soil C content in the Piedmont region of Virginia, United States, a simple C stock accounting system could use the same base soil C stock value for either type of land use. However, since the effects of forest to pasture conversion are a function of grassland management following conversion, assessments of C sequestration rates require activity data on the extent of various grassland management practices.

Rate Model and Mechanism of Liquid-Phase Oxidation of Propionaldehyde

A rate equation is developed for the liquid-phase oxidation of propionaldehyde with oxygen in the presence of manganese propionate catalyst in a sparged reactor. The equation takes into account diffusional limitations based on Brian's solution for mass transfer accompanied by a pseudo m-. nth-order reaction. Sauter-mean bubble diameter, gas holdup, interfacial area, and bubble rise velocity are measured, and rates of mass transfer within the gas phase and across the gas-liquid interface are computed. Statistically designed experiments show the adequacy of the equation. The oxidation reaction is zero order with respect to oxygen concentration, 3/2 order with respect to aldehyde concentration, and order with respect to catalyst concentration. The activation energy is 12.1 kcal/g mole.

AN EXPERIMENTAL STUDY ON EFFERVESCENT ATOMIZATION OF BIO-OIL FUELS

This paper presents the work on detailed characterization of effervescent spray of Jatropha and Pongamia pure plant oils. The spray characteristics of these biofuels are compared with those of diesel. Both macroscopic and microscopic spray characteristics at different injection pressures and gas-to-liquid ratio (GLR) have been studied. The particle/droplet imaging analysis (PDIA) technique along with direct imaging methods are used for the purpose of spray characterization. Due to their higher viscosity, pure plant oils showed poor atomization compared to diesel and a blend of diesel and pure plant oil at a given GLR. Pure plant oil sprays showed a lower spray cone angle when compared to diesel and blends at lower GLRs. However, the difference is not significant at higher GLRs. Droplet size measurements at 100 mm downstream of the exit orifice showed reduction in Sauter mean diameter (SMD) diameter with increase in GLR. A radial variation in the SMD is observed for the blend and pure plant oils. Pure oils showed a larger variation when compared to the blend. Spray unsteadiness has been characterized based on the image-to-image variation in the mean droplet diameter and fluctuations in the spray cone angle. Results showed that pure plant oil sprays are more unsteady at lower GLRs when compared to diesel and blend. A critical GLR is identified at which the spray becomes steady. The three regimes of spray operation, namely ``steady spray,'' ``pulsating spray,'' and ``spray and unbroken liquid jet'' are identified in the injection pressure-GLR parameter space for these pure plant oils. Two-phase flow imaging inside the exit orifice shows that for the pure plant oils, the flow is highly transient at low GLRs and the bubbly, slug, and annular two-phase flow regimes are all observed. However, at higher GLRs where the spray is steady, only the annular flow regime is observed.

Cytotoxicity of aluminium oxide nanoparticles towards fresh water algal isolate at low exposure concentrations

The growing commercial applications had brought aluminium oxide nanoparticles under,toxicologists' purview. In the present study, the cytotoxicity of two different sized aluminium oxide nanoparticles (ANP(1), mean hydrodynamic diameter 82.6 +/- 22 nm and ANP(2), mean hydrodynamic diameter 246.9 +/- 39 nm) towards freshwater algal isolate Chlorella ellipsoids at low exposure levels (<= 1 mu g/mL) using sterile lake water as the test medium was assessed. The dissolution of alumina nanoparticles and consequent contribution towards toxicity remained largely unexplored owing to its presumed insoluble nature. Herein, the leached Al3+ ion mediated toxicity has been studied along with direct particulate toxicity to bring out the dynamics of toxicity through colloidal stability, biochemical, spectroscopic and microscopic analyses. The mean hydrodynamic diameter increased with time both for ANP(1) 82.6 +/- 22 nm (0 h) to 246.3 +/- 59 nm (24h), to 1204 +/- 140 nm (72 h)] and ANP(2) 246.9 +/- 39 nm (Oh) to 368.28 +/- 48 nm (24 h), to 1225.96 +/- 186 nm (72 h)] signifying decreased relative abundance of submicron sized particles (<1000 nm). The detailed cytotoxicity assays showed a significant reduction in the viability dependent on dose and exposure. A significant increase in ROS and LDH levels were noted for both ANPs at 1 mu g/mL concentration. The zeta potential and FT-IR analyses suggested surface chemical interaction between nanoparticles and algal cells. The substantial morphological changes and cell wall damage were confirmed through microscopic analyses (SEM, TEM, and CLSM). At 72 h, significant Al3+ ion release in the test medium 0.092 mu g/mL for ANP(1), and 0.19 mu g/mL for ANP(2)] was noted, and the resulting suspension containing leached ions caused significant cytotoxicity, revealing a substantial ionic contribution. This study indicates that both the nano-size and ionic dissolution play a significant role in the cytotoxicity of ANPs towards freshwater algae, and the exposure period largely determines the prevalent mode of nano-toxicity.

Extension of the universal erosive burning law to partly symmetric propellant grain geometries

This paper aims at extending the universal erosive burning law developed by two of the present authors from axi-symmetric internally burning grains to partly symmetric burning grains. This extension revolves around three dimensional flow calculations inside highly loaded grain geometry and benefiting from an observation that the flow gradients normal to the surface in such geometries have a smooth behavior along the perimeter of the grain. These are used to help identify the diameter that gives the same perimeter the characteristic dimension rather than a mean hydraulic diameter chosen earlier. The predictions of highly loaded grains from the newly chosen dimension in the erosive burning law show better comparison with measured pressure-time curves while those with mean hydraulic diameter definitely over-predict the pressures. (c) 2013 IAA. Published by Elsevier Ltd. All rights reserved.

Relationship between the basic morphometric measurements and growth pattern of Heterotis niloticus from River Kaduna floodplain

A total of 61 specimens of Heterotis niloticus were evaluated by linear regression and correlation. The specimens had mean standard length of 27.09 plus or minus 4.73cm, total length of 33-49cm, mean weight of 2445,108.3g, mean snout length of 48 plus or minus 0.86cm, mean eye diameter of 1.30 plus or minus 0.15cm, mean head length of 6.29 plus or minus 1.75cm. There was a strong relationship between the length and the weight, the eye diameter and the standard length, snout length and the standard length, head length and the standard length, snout length and the weight, head length and the weight (P<0.05). But the correlation of the eye diameters and the weight was insignificant (P>0.05). The growth pattern analysis depicts that the growth was negatively allometric with a b value of 1.16

Some reproductive aspects of Chrysichthys nigrodigitatus (Lacépède) from Cross River, Nigeria

Between May and October 1990, fecundity, egg size and condition factor of Chrysichthys nigrodigitatus (Lacépède) in the Cross River, Nigeria, were studied. The fecundity (F) of this population varied from 3 046 eggs (total length, L=28.5 cm) to 28 086 eggs (L=64 cm). A mean relative fecundity of 231 eggs/cm or 13 eggs/g of fish was obtained for this population. The fecundity of this population can be estimated with the formula F=2.511 · L 2.30 or F=52.893 · W 0.78 , total length being in cm and weight (W) in g. The mean egg diameter of this population varied from 0.65 mm to 3.54 mm. Condition factor (CF) of the population varied from 0.24 to 1.34 with 0.977 as the mean; 52.8% had CF higher than the mean and 47% had CF above unity. Smaller fish in this population were in better condition than bigger ones. The egg size and condition factor obtained in this study are evidence that the Cross River population of C. nigrodigitatus can provide excellent broodstock.

The development of a scanning strategy for the manufacture of porous biomaterials by selective laser melting.

Porous structures are used in orthopaedics to promote biological fixation between metal implant and host bone. In order to achieve rapid and high volumes of bone ingrowth the structures must be manufactured from a biocompatible material and possess high interconnected porosities, pore sizes between 100 and 700 microm and mechanical strengths that withstand the anticipated biomechanical loads. The challenge is to develop a manufacturing process that can cost effectively produce structures that meet these requirements. The research presented in this paper describes the development of a 'beam overlap' technique for manufacturing porous structures in commercially pure titanium using the Selective Laser Melting (SLM) rapid manufacturing technique. A candidate bone ingrowth structure (71% porosity, 440 microm mean pore diameter and 70 MPa compression strength) was produced and used to manufacture a final shape orthopaedic component. These results suggest that SLM beam overlap is a promising technique for manufacturing final shape functional bone ingrowth materials.

黄土丘陵沟壑区人工林地的土壤抗蚀性评价

以延安、安塞、吴旗的人工刺槐林、柠条林为研究对象,选取同一地区的自然恢复草地和坡耕地为对照,通过对5个表征土壤抗蚀性的指标即>0.25 mm水稳性团粒含量、>0.5 mm水稳性团粒含量、平均重量直径、团聚状况和团聚度的比较分析,对人工刺槐林、人工柠条林相对于自然恢复草地和坡耕地改善土壤抗蚀性的效果进行了评价,同时分析了不同林龄人工林土壤抗蚀性的变化。研究表明,人工林地相对于坡耕地,显著提高了土壤抗蚀性,但不及自然恢复草地,尤其在安塞和吴旗表现更明显;随着林龄的增长,人工林地土壤抗蚀性能增强,并趋于稳定。并通过对样地的聚类分析,也得出与上述相似的结果。综合分析表明,封禁条件下的植被自然恢复是黄土丘陵沟壑区比较适宜的植被恢复方式和控制土壤侵蚀的有效措施。