Magnesium hydroxide-based peroxide bleaching of high-brightness mechanical pulps

A high final brightness is desired in most paper and board products. This requires bleaching processes that are able to produce high-brightness pulps. Mechanical pulps are widely bleached for high brightness using alkaline hydrogen peroxide with traditional sodium hydroxide and sodium silicate as additives. With high doses however, peroxide bleaching causes high organic loads in the mill effluent and anionic trash carry-over to papermaking. To alleviate the problems that arise from the use of sodium-based additives in peroxide bleaching, interest in the use of alternative magnesium-based chemicals has increased. In this study, a new, technical high-purity magnesium hydroxide-based bleaching additive was evaluated on laboratory-scale, pilot-scale and mill-scale experiments and trials for its ability to produce a high brightness in peroxide bleaching without the known problems of sodium-based chemicals. The key findings of this study include: a high brightening potential of peroxide bleaching using the Mg(OH)2-based additive, significant reductions (40-70%) in all categories of environmental load, and cationic demand lowered by 60-70% in bleached pulp with no loss in strength properties or in sheet bulk. When used in TMP refiner bleaching, the Mg(OH)2-based additive resulted in savings in specific energy consumption and provided a good bleaching response.

In situ aberration corrected-transmission electron microscopy of magnesium oxide nanocatalysts for biodiesels

Biofuels are promising renewable energy sources and can be derived from vegetable oil feedstocks. Although solid catalysts show great promise in plant oil triglyceride transesterification to biodiesel, the identification of active sites and operating surface nanostructures created during their processing is essential for the development of efficient heterogeneous catalysts. Systematic, direct observations of dynamic MgO nanocatalysts from a magnesium hydroxide-methoxide precursor were performed under controlled calcination conditions using novel in situ aberration corrected-transmission electron microscopy at the 0.1 nm level and quantified with catalytic reactivity and physico-chemical studies. Surface structural modifications and the evolution of extended atomic scale glide defects implicate coplanar anion vacancies in active sites in the transesterification of triglycerides to biodiesel. The linear correlation between surface defect density (and therefore polarisability) and activity affords a simple means to fine tune new, energy efficient nanocatalysts for biofuel synthesis. © 2009 Springer Science+Business Media, LLC.

Didanosine-loaded Chitosan Microspheres Optimized By Surface-response Methodology: A Modified Maximum Likelihood Classification" Approach Formulation For Reverse Transcriptase Inhibitors."

Didanosine-loaded chitosan microspheres were developed applying a surface-response methodology and using a modified Maximum Likelihood Classification. The operational conditions were optimized with the aim of maintaining the active form of didanosine (ddI), which is sensitive to acid pH, and to develop a modified and mucoadhesive formulation. The loading of the drug within the chitosan microspheres was carried out by ionotropic gelation technique with sodium tripolyphosphate (TPP) as cross-linking agent and magnesium hydroxide (Mg(OH)2) to assure the stability of ddI. The optimization conditions were set using a surface-response methodology and applying the Maximum Likelihood Classification, where the initial chitosan concentration, TPP and ddI concentration were set as the independent variables. The maximum ddI-loaded in microspheres (i.e. 1433mg of ddI/g chitosan), was obtained with 2% (w/v) chitosan and 10% TPP. The microspheres depicted an average diameter of 11.42μm and ddI was gradually released during 2h in simulated enteric fluid.

Vaihtoehtoalkalit mekaanisen massan peroksidivalkaisussa

Tehokkain tapavalkaista mekaanisesti kuidutettua puumassaa on suorittaa se hapettavasti peroksidikemikaalilla vahvasti alkalisissa oloissa. Perinteisesti alkalisuus on aikaansaatu natriumhydroksidin ja -silikaatin avulla. Se kuitenkin liuottaa massasta merkittävästi ligniiniä, mikä huonontaa saantoa ja suurentaa valkaisun jätevesien orgaanisen hiilen määrää sekä kemiallista hapenkulutusta. Yhä kovenevien vaaleustavoitteiden ja tiukentuneen vedenkäytön seurauksena on syntynyt tarve etsiä parempia valkaisun alkaleja. Kirjallisuuden pohjalta valittiinkokeellisesti tutkittaviksi alkaleiksi magnesiumhydroksidi, magnesiumoksidi, kalsiumhydroksidi sekä kalsiumoksidi. Niiden toimivuutta hapettavan vetyperoksidivalkaisun alkaleina tutkittiin valkaisukokein natriumsilikaattilisäyksen kanssa sekä ilman. Näistä parhaiten toimivaksi osoittautui Mg(OH)2. Sen avulla suoritettiin jatkoksi laboratoriokoevalkaisuja korkeassa sakeudessa. Keski- ja korkeasakeusvalkaisukokeiden tulosten mukaan käytettäessä Mg(OH)2 -alkalia natriumydroksidin ja -silikaatin asemesta jää massan loppuvaaleus noin yhden ISO-prosentin verran heikommaksi. Tällöin valkaisusuodoksessa oli vain varsin vähäinen määrä massasta liuennutta orgaanista hiiliainesta, noin 45 % siitä, mitä natriumin yhdisteiden käyttö vertailukokeessa tuotti. Tulosta varmennettiin suorittamalla korkea-sakeusvalkaisukokeita hiokemassatehtaan olosuhteissa, massoilla ja kiertovesillä.Myös tehdaskokeiden mukaan valkaistun massan loppuvaaleus jää noin yhden ISO-prosentin alhaisemmaksi, mutta valkaisusuodoksen orgaanisen hiilen määrä (TOC) jääalle puoleen Na-kemikaalein suoritetusta vertailukokeesta.

Cutting edge: alum adjuvant stimulates inflammatory dendritic cells through activation of the NALP3 inflammasome.

Adjuvants are vaccine additives that stimulate the immune system without having any specific antigenic effect of itself. In this study we show that alum adjuvant induces the release of IL-1beta from macrophages and dendritic cells and that this is abrogated in cells lacking various NALP3 inflammasome components. The NALP3 inflammasome is also required in vivo for the innate immune response to OVA in alum. The early production of IL-1beta and the influx of inflammatory cells into the peritoneal cavity is strongly reduced in NALP3-deficient mice. The activation of adaptive cellular immunity to OVA-alum is initiated by monocytic dendritic cell precursors that induce the expansion of Ag-specific T cells in a NALP3-dependent way. We propose that, in addition to TLR stimulators, agonists of the NALP3 inflammasome should also be considered as vaccine adjuvants.

Häiriöaineiden vaikutus käytettäessä magnesiumhydroksidialkalia mekaanisen massan peroksidivalkaisussa

Nykypäivänä ympäristön suojelu ja erityisesti jätevesipäästöjen pienentäminen vaikuttavat yhä enemmän metsäteollisuuden toimintatapoihin. Lisäksi veden käytön vähentyessä ja prosesseja suljettaessa silikaatteihin väistämättä liittyvät saostumat ovat kasvava ongelma. Magnesiumhydroksidin on havaittu olevan potentiaalinen natriumhydroksidin korvaava alkali mekaanisen massan peroksidivalkaisussa. Lisäksi magnesiumhydroksidilla voidaan saavuttaa lähes yhtä korkea vaaleus, jopa ilman silikaattia, kuin natriumhydroksidilla natriumsilikaatin kanssa. Magnesiumhydroksidin orgaanista ainesta liuottava vaikutus on myös noin puolet verrattuna natriumhydroksidiin. Työssä selvitettiin, miten häiriöaineet vaikuttavat mekaanisen massan peroksidivalkaisuun käytettäessä magnesiumhydroksidialkalia. Laboratoriokokeiden tulokset osoittivat, että magnesiumhydroksidi kesti paremmin valkaisussa käytettyjä häiriöaineita. Pienillä metallilisäyksillä ei ole vaikutusta massan vaaleuteen käytettäessä magnesiumhydroksidia. Korvattaessa laimennusvettä viirapuristimen suodoksella peroksidi kului lähes loppuun käytettäessä natriumhydroksidia, mikä näkyi myös vaaleuden heikkenemisenä. Valkaisukokeiden perusteella magnesiumhydroksidialkalilla jäädään jopa kolme prosenttiyksikköä natriumhydroksidin kanssa saadusta vaaleudesta, peroksidiannoksen olleessa kolme prosenttia. Mutta käytettäessä magnesiumhydroksidialkalia liuenneen orgaanisen hiilen kokonaismäärä (TOC) sekä biologinen (BOD7) että kemiallinen (CODcr) hapenkulutus pienenivät lähes puolella.

Magnesiumhydroksidialkalin käytön vaikutukset päällystämättömän aikakauslehtipaperin valmistukseen

Magnesiumhydroksidin on havaittu soveltuvan natriumhydroksidin korvaajaksi mekaanisen massan peroksidivalkaisun alkalina. Työssä selvitettiin, miten magnesiumhydroksidi vaikuttaa paperin valmistukseen ja valmiin paperin ominaisuuksiin. Laboratoriokokeet osoittivat magnesiumhydroksidin soveltuvan mekaanisen massan peroksidivalkaisun alkaliksi, sillä vaaleustavoite saavutettiin sen avulla. Valkaistun massan varaustila, johtokyky sekä ζ -potentiaali laskivat magnesiumhydroksidin vaikutuksesta. Nämä johtivat huomattavasti korkeampaan paperin täyteaineretentioon. Massan vedenpidätyskyky kasvoi korvattaessa natriumhydroksidi magnesiumhydroksidilla. Arkkien ominaisuuksista vetoindeksi, valonsirontakerroin ja taivutusjäykkyys kasvoivat. Kaikki edellä mainitut ominaisuudet viittaavat siihen, että magnesiumhydroksidin käyttö parantaa hienoaineen sitoutumista paperiin.

Influence of reactant absorption and dissolution in heterogeneous precipitation processes

In this research work, the aim was to investigate the volumetric mass transfer coefficient [kLa] of oxygen in stirred tank in the presence of solid particle experimentally. The kLa correlations as a function of propeller rotation speed and flow rate of gas feed were studied. The O2 and CO2 absorption in water and in solid-liquid suspensions and heterogeneous precipitation of MgCO3 were thoroughly examined. The absorption experiments of oxygen were conducted in various systems like pure water and in aqueous suspensions of quartz and calcium carbonate particles. Secondly, the precipitation kinetics of magnesium carbonate was also investigated. The experiments were performed to study the reactive crystallization with magnesium hydroxide slurry and carbon dioxide gas by varying the feed rates of carbon dioxide and rotation speeds of mixer. The results of absorption and precipitation are evaluated by titration, total carbon (TC analysis), and ionic chromatrography (IC). For calcium carbonate, the particle concentration was varied from 17.4 g to 2382 g with two size fractions: 5 µm and 45-63 µm sieves. The kLa and P/V values of 17.4 g CaCO3 with particle size of 5µm and 45-63 µm were 0.016 s-1 and 2400 W/m3. At 69.9 g concentration of CaCO3, the achieved kLa is 0.014 s-1 with particle size of 5 µm and 0.017 s-1 with particle size of 45 to 63 µm. Further increase in concentration of calcium carbonate, i.e. 870g and 2382g , does not affect volumetric mass transfer coeffienct of oxygen. It could be concluded from absorption results that maximum value of kLa is 0.016 s-1. Also particle size and concentration does affect the transfer rate to some extend. For precipitation experiments, the constant concentration of Mg(OH)2 was 100 g and the rotation speed varied from 560 to 750 rpm, whereas the used feed rates of CO2 were 1 and 9 L/min. At 560 rpm and feed rate of CO2 is 1 L/min, the maximum value of Mg ion and TC were 0.25 mol/litre and 0.12 mol/litre with the residence time of 40 min. When flow rate of CO2 increased to 9 L/min with same 560 rpm, the achieved value of Mg and TC were 0.3 mol/litre and 0.12 mol/L with shorter residence time of 30 min. It is concluded that feed rate of CO2 is dominant in precipitation experiments and it has a key role in dissociation and reaction of magnesium hydroxide in precipitation of magnesium carbonate.

Influence of multi-phase phenomena on semibatch crystallization processes of aqueous solutions

Crystal properties, product quality and particle size are determined by the operating conditions in the crystallization process. Thus, in order to obtain desired end-products, the crystallization process should be effectively controlled based on reliable kinetic information, which can be provided by powerful analytical tools such as Raman spectrometry and thermal analysis. The present research work studied various crystallization processes such as reactive crystallization, precipitation with anti-solvent and evaporation crystallization. The goal of the work was to understand more comprehensively the fundamentals, phenomena and utilizations of crystallization, and establish proper methods to control particle size distribution, especially for three phase gas-liquid-solid crystallization systems. As a part of the solid-liquid equilibrium studies in this work, prediction of KCl solubility in a MgCl2-KCl-H2O system was studied theoretically. Additionally, a solubility prediction model by Pitzer thermodynamic model was investigated based on solubility measurements of potassium dihydrogen phosphate with the presence of non-electronic organic substances in aqueous solutions. The prediction model helps to extend literature data and offers an easy and economical way to choose solvent for anti-solvent precipitation. Using experimental and modern analytical methods, precipitation kinetics and mass transfer in reactive crystallization of magnesium carbonate hydrates with magnesium hydroxide slurry and CO2 gas were systematically investigated. The obtained results gave deeper insight into gas-liquid-solid interactions and the mechanisms of this heterogeneous crystallization process. The research approach developed can provide theoretical guidance and act as a useful reference to promote development of gas-liquid reactive crystallization. Gas-liquid mass transfer of absorption in the presence of solid particles in a stirred tank was investigated in order to gain understanding of how different-sized particles interact with gas bubbles. Based on obtained volumetric mass transfer coefficient values, it was found that the influence of the presence of small particles on gas-liquid mass transfer cannot be ignored since there are interactions between bubbles and particles. Raman spectrometry was successfully applied for liquid and solids analysis in semi-batch anti-solvent precipitation and evaporation crystallization. Real-time information such as supersaturation, formation of precipitates and identification of crystal polymorphs could be obtained by Raman spectrometry. The solubility prediction models, monitoring methods for precipitation and empirical model for absorption developed in this study together with the methodologies used gives valuable information for aspects of industrial crystallization. Furthermore, Raman analysis was seen to be a potential controlling method for various crystallization processes.

Carponate precipitation with carbon dioxide gas

The aim of this thesis research work focused on the carbonate precipitation of magnesium using magnesium hydroxide Mg(OH)2 and carbon dioxide (CO2) gas at ambient temperature and pressure. The rate of dissolution of Mg(OH)2 and precipitation kinetics were investigated under different operating conditions. The conductivity and pH of the solution were inline monitored by a Consort meter and the solid samples gotten from the precipitation reaction were analysed by a laser diffraction analyzer Malvern Mastersizer to obtain particle size distributions (PSD) of crystal samples. Also the Mg2+ concentration profiles were determined from the liquid phase of the precipitate by ion chromatography (IC) analysis. Crystal morphology of the obtained precipitates were also investigated and discussed in this work. For the carbonation reaction of magnesium hydroxide in the present work, it was found that magnesium carbonate trihydrate (nesquehonite) was the main product and its formation occurred at a pH of around 7-8. The stirrer speed has a significant effect on the dissolution rate of Mg(OH)2. The highest obtained Mg2+ concentration level was 0.424 mol L-l for the 470 rpm and 0.387 mol L-1 for the 560 rpm which corresponded to the processing time of 45 mins and 40 mins respectively. The particle size distribution shows that the average particle size keeps increasing during the reaction as the CO2 is been fed to the system. The carbonation process is kinetically favored and simple as nesquehonite formation occurs in a very short time. It is a thermodynamically and chemically stable solid product, which allows for a long-term storage of CO2. Since the carbonation reaction is a complex system which includes dissolution of magnesium hydroxide particles, absorption of CO2, chemical reaction and crystallization, the dissolution of magnesium hydroxide was studied in hydrochloric acid (HCl) solvent with and without nitrogen (N2) inert gas. It was found on the dissolution part that the impeller speed had effect on the dissolution rate. The higher the impeller speed the higher the pH of the solution, although for the highest speed of 650rpm it was not the case. Therefore, it was concluded that the optimum speed of the stirrer was 560rpm. The influence of inert gas N2 on the dissolution rate of Mg(OH)2 particles could be seen based on measured pH, electric conductivity and Mg2+ concentration curves.

Aplicação da água residuária das salinas no tratamento de efluente têxtil

The treatment of colored and alkaline effluent has been a challenge to the textile industry. An alternative to remove the colors of those effluents is applying magnesium chloride as a coagulant agent. The magnesium ion, in high pH, hydrolyzes itself, forming the magnesium hydroxide which has a large adsorptive area and positive electrostatic charges able to act as an efficient coagulant. The bittern wastewater from the salt industries has been studied as a potential font of this magnesium ion. Nowadays, this bittern wastewater is evicted into the sea, without any treatment or other use. This thesis has evaluated the potential of applying the wastewater from the salt industries in the treatment of dyeing effluent containing indigo dye and alkaline pH. All the experiments were made in jar tests simulating the chemical coagulation, flocculation and decantation steps ranging the pH and the concentration of magnesium ion. Were obtained removals between 96% and 76% for turbidity, apparent color, and true color, respectively, using 200mg/L Mg2+. The reduction of costs with acid, when were used the salt industries wastewater, comparing with Al2(SO4)3, was 62%. For the degradation of organic matter remaining in the clarified, around 900 mg/L, was applyed the advanced process of oxidation: photo-Fenton. The preliminary results showed 57% reduction in DOC. According to the results obtained, the salt industries wastewater can be applied, as coagulant, in the physical-chemical treatment of the denim dyeing wastewater, so it is not necessary a previous adjust of pH, efficiently and economically

Tamponamento cecal: aspectos clínico, fisiopatológico e terapêutico na laminite experimental em eqüinos

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Concentration of trace elements in samples of sea water determined by use of two methods of concentrating

A device and a specific procedure for simultaneous concentration of trace ele¬ments from sea water by co-precipitating them in precipitate of magnesium hydroxide obtained by electrolytic alkalization of samples in a two-chamber electrolyzer are described. Analyses of sea water samples for zinc, iron, copper, nickel and lead demonstrate that the method produces a thousand-fold concentration and gives results that agree well with those obtained by extractive concentration using diethyldithiocarbamate and 8-hydroxyquinoline in chloroform. Extracts were analyzed by flame atomic absorption. Correlation coefficients of results obtained with use of these two methods of concentration were 0.76-0.87 for zinc, iron, and copper at confidence levels of 0.05-0.07. Average zinc and iron concentrations determined by the method differed by less than 10%.

Phosphate d18O pore-water profiles of sediment core GeoB11807-2 and GeoB11804-4

Phosphorus cycling in the ocean is influenced by biological and geochemical processes that are reflected in the oxygen isotope signature of dissolved inorganic phosphate (Pi). Extending the Pi oxygen isotope record from the water column into the seabed is difficult due to low Pi concentrations and small amounts of marine porewaters available for analysis. We obtained porewater profiles of Pi oxygen isotopes using a refined protocol based on the original micro-extraction designed by Colman (2002). This refined and customized method allows the conversion of ultra-low quantities (0.5 - 1 µmol) of porewater Pi to silver phosphate (Ag3PO4) for routine analysis by mass spectrometry. A combination of magnesium hydroxide co-precipitation with ion exchange resin treatment steps is used to remove dissolved organic matter, anions, and cations from the sample before precipitating Ag3PO4. Samples as low as 200 µg were analyzed in a continuous flow isotope ratio mass spectrometer setup. Tests with external and laboratory internal standards validated the preservation of the original phosphate oxygen isotope signature (d18OP) during micro extraction. Porewater data on d18OP has been obtained from two sediment cores of the Moroccan margin. The d18OP values are in a range of +19.49 to +27.30 per mill. We apply a simple isotope mass balance model to disentangle processes contributing to benthic P cycling and find evidence for Pi regeneration outbalancing microbial demand in the upper sediment layers. This highlights the great potential of using d18OP to study microbial processes in the subseafloor and at the sediment water interface.

Comparativa de métodos de descontaminación de suelos afectados por hidrocarburos. Aplicación a la obra del AVE de Málaga

El objetivo de esta tesis, va a ser la investigación y desarrollo de tratamientos de biorremediación para conseguir la recuperación de los terrenos contaminados situados en el tramo del tren de alta velocidad entre Córdoba y Málaga, reduciendo de esta forma los residuos enviados a vertederos. Para ello, se va a investigar y a desarrollar una tecnología innovadora de descontaminación in situ de suelos con altas concentraciones de hidrocarburos, basándonos en el landfarming y como principal avance la coexistencia con hidróxido de magnesio, elemento no utilizado nunca y potencialmente muy útil. Se va a pretender reducir la concentración final de hidrocarburos y el tiempo de tratamiento, sin transportar a vertedero los residuos. Se desean conseguir las condiciones ambientales óptimas que permitan potenciar la degradación microbiana de los hidrocarburos y sus productos residuales en corto tiempo Se va a investigar el empleo del hidróxido de magnesio como complemento al landfarming y a buscar las sinergias de este compuesto como gran fijador de metales pesados. ABSTRACT The aim of this thesis will be the research and development of bioremediation treatments for the recovery of contaminated land in the stretch of the high speed train between Cordoba and Malaga, thereby reducing waste sent to landfills. To do this, is to research and develop innovative technology for in situ remediation of soil with high concentrations of hydrocarbons, based on the main progress landfarming and coexistence with magnesium hydroxide, item never used and potentially very useful. It will pretend to reduce the final hydrocarbon concentration and treatment time, without transporting waste landfill. They want to get the optimum environmental conditions for enhancing microbial degradation of hydrocarbons and waste products in a short time It will investigate the use of magnesium hydroxide as a complement to landfarming and seek synergies of this compound as a great fixer of heavy metals.