Evaluation of dichroic material for enhancing light pipe/natural ventilation and daylighting in an integrated system

Integration of natural ventilation and daylighting in a single installation would make both technologies more attractive. One method for the integration is the use of concentric light pipe and ventilation stack. By constructing the light pipe using dichroic materials, the infrared part of the solar radiation is allowed to be transmitted to the stack but the visible light is guided by the light pipe into a room. The heat gain to the interior can be reduced and the thermal stack effect strengthened. Work presented here involved the experimental and computational evaluation of dichroic materials for enhancing both natural stack ventilation and daylighting. The transmittance of a dichroic light pipe was found to be similar to that of a light pipe with a 95% specular reflectance. The infra-red radiation transmitted through the dichroic material into a passive stack was found to enhance the natural ventilation flow by up to 14%. The effect is greater in summer than in winter, which is highly desirable as there is often a lack of driving force for natural stack ventilation in summer.

Raytracing simulation for predicting light pipe transmittance

Daylighting systems can offer energy savings primarily by reducing electric lighting usage. Accurate predictive models of daylighting system performances are crucial for effective design and implementation of this renewable energy technology. A comparative study of predictive methods was performed and the use of a commercial raytracing software program was validated as a method of predicting light pipe performance. Raytracing simulation was shown to more accurately predict transmission effi ciency than existing analytical methods.

Post occupancy evaluation of a building employing windcatchers for summer ventilation

A combined windcatcher and light pipe (SunCatcher) was installed in the seminar room at the University of Reading, UK. Monitoring of indoor environment in real weather conditions was conducted to evaluate the application of windcatchers for natural ventilation. In addition, a subjective occupancy survey was undertaken. External weather conditions and internal indoor air quality indicators were recorded. The “tracer-gas decay” method using SF6 was used to establish air change rate for various conditions. The results indicated that the ventilation rate achieved through the windcatcher depends on the difference between internal and external air temperatures, and on wind speed and direction, in agreement with other published work in the area. The indoor air quality parameters were found to be within acceptable levels when the windcatcher was in operation. The measured air change rate was between 1.5ac/h and 6.8ac/h. Occupants’ questionnaires showed 75 per cent satisfaction with the internal conditions and welcomed the installation of the systems in UK buildings.

Comparing detection and location performance of perpendicular and parallel broadside GPR antenna orientations

GPR (Ground Penetrating Radar) results are shown for perpendicular broadside and parallel broadside antenna orientations. Performance in detection and localization of concrete tubes and steel tanks is compared as a function of acquisition configuration. The comparison is done using 100 MHz and 200 MHz center frequency antennas. All tubes and tanks are buried at the geophysical test site of IAG/USP in Sao Paulo city, Brazil. The results show that the long steel pipe with a 38-mm diameter was well detected with the perpendicular broadside configuration. The concrete tubes were better detected with the parallel broadside configuration, clearly showing hyperbolic diffraction events from all targets up to 2-m depth. Steel tanks were detected with the two configurations. However, the parallel broadside configuration was generated to a much lesser extent an apparent hyperbolic reflection corresponding to constructive interference of diffraction hyperbolas of adjacent targets placed at the same depth. Vertical concrete tubes and steel tanks were better contained with parallel broadside antennas, where the apexes of the diffraction hyperbolas better corresponded to the horizontal location of the buried target disposition. The two configurations provide details about buried targets emphasizing how GPR multi-component configurations have the potential to improve the subsurface image quality as well as to discriminate different buried targets. It is judged that they hold some applicability in geotechnical and geoscientific studies. (C) 2009 Elsevier B.V. All rights reserved.

The influence of the flow of the reacting gas on the conditions for a thermal explosion

The classical problem of thermal explosion is modified so that the chemically active gas is not at rest but is flowing in a long cylindrical pipe. Up to a certain section the heat-conducting walls of the pipe are held at low temperature so that the reaction rate is small and there is no heat release; at that section the ambient temperature is increased and an exothermic reaction begins. The question is whether a slow reaction regime will be established or a thermal explosion will occur. The mathematical formulation of the problem is presented. It is shown that when the pipe radius is larger than a critical value, the solution of the new problem exists only up to a certain distance along the axis. The critical radius is determined by conditions in a problem with a uniform axial temperature. The loss of existence is interpreted as a thermal explosion; the critical distance is the safe reactor’s length. Both laminar and developed turbulent flow regimes are considered. In a computational experiment the loss of the existence appears as a divergence of a numerical procedure; numerical calculations reveal asymptotic scaling laws with simple powers for the critical distance.

Development of a non-intrusive heat transfer coefficient gauge and its application to high pressure die casting Effect of the process parameters

A heat transfer coefficient gauge has been built, obeying particular rules in order to ensure the relevance and accuracy of the collected information. The gauge body is made out of the same materials as the die casting die (H13). It is equipped with six thermocouples located at different depths in the body and with a sapphire light pipe. The light pipe is linked to an optic fibre, which is connected to a monochromatic pyrometer. Thermocouples and pyrometer measurements are recorded with a data logger. A high pressure die casting die was instrumented with one such gauge. A set of 150 castings was done and the data recorded. During the casting, some process parameters have been modified such as piston velocity, intensification pressure, delay before switch to the intensification stage, temperature of the alloy, etc.... The data was treated with an inverse method in order to transform temperature measurements into heat flux density and heat transfer coefficient plots. The piston velocity and the initial temperature of the die seem to be the process parameters that have the greatest influence on the heat transfer. (c) 2005 Elsevier B.V. All rights reserved.

Analysis of long-term light-trap data for Helicoverpa spp. (Lepidoptera : Noctuidae) in Australia: the effect of climate and crop host plants

Regression analyses of a long series of light-trap catches at Narrabri, Australia, were used to describe the seasonal dynamics of Helicoverpa armigera (Hubner). The size of the second generation was significantly related to the size of the first generation, to winter rainfall, which had a positive effect, and to spring rainfall which had a negative effect. These variables accounted for up to 96% of the variation in size of the second generation from year to year. Rainfall and crop hosts were also important for the size of the third generation. The area and tonnage of many potential host crops were significantly correlated with winter rain. When winter rain was omitted from the analysis, the sizes of both the second and third generations could be expressed as a function of the size of the previous generation and of the areas planted to lucerne, sorghum and maize. Lucerne and maize always had positive coefficients and sorghum a negative one. We extended our analysis to catches of H. punctigera (Wallengren), which declines in abundance after the second generation. Winter rain had a positive effect on the sizes of the second and third generations, and rain in spring or early summer had a negative effect. Only the area grown to lucerne had a positive effect on abundance. Forecasts of pest levels from a few months to a few weeks in advance are discussed, along with the improved understanding of the seasonal dynamics of both species and the significance of crops in the management of insecticide resistance for H. armigera.

Argon ion laser and halogen lamp activation of a dark and light resin composite: microhardness after long-term storage

The objective of this study was to evaluate in vitro light activation of the nano-filled resin composite Vita shade A1 and A3 with a halogen lamp (QTH) and argon ion laser by Knoop microhardness profile. Materials and methods: Specimens of nanofilled composite resin (Z350-3 M-ESPE) Vita shade A1 and A3 were prepared with a single increment inserted in 2.0-mm-thick and 3-mm diameter disc-shaped Teflon mold. The light activation was performed with QTH for 20 s (with an intensity of approximately 1,000 mW/cm(2) and 700 mW/cm(2)) and argon ion laser for 10 s (with a power of 150 mW and 200 mW). Knoop microhardness test was performed after 24 h and 6 months. The specimens were divided into the 16 experimental groups (n = 10), according to the factors under study: photoactivation form, resin shade, and storage time. Knoop microhardness data was analyzed by a factorial ANOVA and TukeyA ` s tests at the 0.05 level of significance. Results: Argon ion laser was not able to photo-activate the darker shade of the nanofilled resin composite evaluated but when used with 200 mW it can be as effective as QTH to photo-activate the lighter shade with only 50% of the time exposure. After 6 months storage, an increase in the means of Knoop microhardness values were observed. Conclusions: Light-activation significantly influenced the Knoop microhardness values for the darker nanofilled resin composite.

Differential effect of long versus short wavelength light exposure on pupillary re-dilation in patients with outer retinal disease.

BACKGROUND: In patients with outer retinal degeneration, a differential pupil response to long wavelength (red) versus short wavelength (blue) light stimulation has been previously observed. The goal of this study was to quantify differences in the pupillary re-dilation following exposure to red versus blue light in patients with outer retinal disease and compare them with patients with optic neuropathy and with healthy subjects. DESIGN: Prospective comparative cohort study. PARTICIPANTS: Twenty-three patients with outer retinal disease, 13 patients with optic neuropathy and 14 normal subjects. METHODS: Subjects were tested using continuous red and blue light stimulation at three intensities (1, 10 and 100 cd/m2) for 13 s per intensity. Pupillary re-dilation dynamics following the brightest intensity was analysed and compared between the three groups. MAIN OUTCOME MEASURES: The parameters of pupil re-dilation used in this study were: time to recover 90% of baseline size; mean pupil size at early and late phases of re-dilation; and differential re-dilation time for blue versus red light. RESULTS: Patients with outer retinal disease showed a pupil that tended to stay smaller after light termination and thus had a longer time to recovery. The differential re-dilation time was significantly greater in patients with outer retinal disease (median = 28.0 s, P < 0.0001) compared with controls and patients with optic neuropathy. CONCLUSIONS: A differential response of pupil re-dilation following red versus blue light stimulation is present in patients with outer retinal disease but is not found in normal eyes or among patients with visual loss from optic neuropathy.

Formulazione e messa a punto di una metodologia per il progetto di ventilatori per gallerie del vento con applicazione al "long-pipe" del laboratorio CICLoPE : analisi attraverso l'impiego di modelli matematici in MATLAB

Nell'ottica di un futuro riprogetto, totale o parziale, del ventilatore della galleria del vento del progetto CICLoPE dell'Università di Bologna, è stato messo a punto, grazie a modelli matematici di letteratura, un algoritmo per la determinazione della geometria delle pale di un fan. La procedura si basa su ipotesi di incompressibilità e assenza di vortici di estremità ed è in grado di fornire la geometria del ventilatore una volta che sono state fissate: le condizioni richieste nella sezione di test, l'efficienza del tunnel e alcune proprietà del ventilatore stesso (ad esempio tipologia di profilo aerodinamico e numero di pale). L'algoritmo è in grado di lavorare solamente con la configurazione ventilatore seguito da profili raddrizzatori, ma è in previsione un'estensione che consentirà di studiare anche la configurazione a fan controrotanti (come quella del CICLoPE). Con questo software sono state progettate numerose soluzioni diverse per studiare il legame tra rendimento e geometria del ventilatore. Inoltre sono stati individuati i parametri che permettono di ottenere una pala con rastremazione e svergolatura trascurabili, con lo scopo di abbassare i costi del manufatto. In particolare è stato dimostrato come le configurazioni con diametro della nacelle grande (superiore al 65\% del diametro della sezione di potenza) siano particolarmente adatte a fornire rendimenti alti con la minima complicatezza della pala. Per quanto riguarda l'efficienza aerodinamica del profilo, i test comparativi indicano che questo parametro influisce relativamente poco sul rendimento del macchinario ma modifica profondamente la geometria della pala. Efficienze elevate tendono, secondo lo studio, a richiedere pale estremamente rastremate e poco svergolate; questo porta a preferire l'adozione di profili mediamente efficienti ma dall'ampio intervallo operativo in termini di angolo di attacco.

Analisi sperimentale di un sistema per il posizionamento e la movimentazione di sensori in galleria del vento, con applicazione al "long-pipe" in CICLoPE

Analisi di un sistema per il posizionamento e la movimentazione di sensori in galleria del vento. In particolare l’analisi è stata focalizzata sul sistema di movimentazione sonde (traversing) presente nel long-pipe in CICLoPE (Center for International Cooperation in Long Pipe Experiments). La struttura menzionata nasce per far fronte ad alcuni dei limiti presenti negli attuali laboratori fluidodinamici per lo studio della turbolenza ad alti numeri di Reynolds. Uno degli obiettivi del centro è quello di caratterizzare le più piccole strutture caratteristiche della turbolenza. Al fine di permettere tale studio era necessario migliorare il traversing esistente per ottenere movimenti ad alta precisione, in modo da raggiungere lo stesso ordine di grandezza delle scale più piccole della turbolenza. Il miglioramento di tale strumentazione è stato necessario anche per fornire un valido supporto alle metodologie esistenti per la determinazione della distanza tra sonde e parete, che resta una delle difficoltà nello studio della turbolenza di parete. L’analisi del traversing, svolta attraverso più test, ha fatto emergere problemi sia nella struttura del sistema, sia nel software che gestisce il motore per la movimentazione. La riprogrammazione del software e la rettifica di alcuni componenti del sistema hanno permesso di eliminare gli errori emersi. Le piccole imprecisioni restanti durante la movimentazione, non eliminabili con un’implementazione software, verranno totalmente superate grazie all’impiego del nuovo motore dotato di un encoder rotativo che sarà in grado di retroazionare il sistema, fornendo il reale spostamento effettuato.

Anemometria a filo caldo: studio di un sistema di calibrazione per sonde a due fili con applicazione al "long pipe" in CICLoPE

L’anemometro a filo caldo (in inglese hot wire) é lo strumento maggiormente usato per studiare sperimentalmente la turbolenza. A seconda di quante componenti della velocitá interessa studiare, esistono anemometri a uno, due o tre fili. Questo elaborato di tesi si concentra su sonde a due fili. Per prima cosa, ogni volta che si utilizza questo strumento bisogna effettuare una calibrazione, fase molto importante perché permette di relazionare le tensioni che ogni filo acquisisce con la velocitá reale del flusso. Sono presentati tre differenti metodi utilizzati per sonde a due fili e, dopo averli analizzati, sono stati applicati a dati acquisiti prima al CAT (Coaxial Aerodinamic Tunnel), struttura presente a Forlí, nell’hangar dell’Universitá di Bologna e poi al CICLoPE (Center for International Cooperation in Long Pipe Experiments), Long-Pipe costruito a Predappio, utilizzato per lo studio della turbolenza. La calibrazione per sonde a due fili si puó dividere in due parti, quella di velocitá e quella per gli angoli. Mentre al CAT é possibile effettuarle entrambi, al CICLoPE non é attualmente possibile eseguire la calibrazione angolare perché non esiste alcuno strumento utilizzabile per regolare la sonda all’angolo desiderato. Lo scopo di questo elaborato di tesi è trovare un metodo di calibrazione per sonde a due fili applicabile al CICLoPE eseguendo sul posto solamente una calibrazione di velocitá e adattando quella angolare effettuata precedentemente al CAT. Questo puó provocare dei problemi perché la calibrazione risulta fortemente dipendente da condizioni interne dei fili, come la resistenza, ma anche da condizioni al contorno, come la temperatura e la pressione dell’ambiente esterno. Dopo aver eseguito due campagne sperimentali di test, una al CAT e una al CICLoPE, i dati acquisiti sono stati elaborati per valutare l’efficacia dei vari metodi.

Long-Distance Electronic Energy Transfer in Light-Harvesting Supramolecular Polymers.

The efficient collection of solar energy relies on the design and construction of well-organized light-harvesting systems. Herein we report that supramolecular phenanthrene polymers doped with pyrene are effective collectors of light energy. The linear polymers are formed through the assembly of short amphiphilic oligomers in water. Absorption of light by phenanthrene residues is followed by electronic energy transfer along the polymer over long distances (>100 nm) to the accepting pyrene molecules. The high efficiency of the energy transfer, which is documented by large fluorescence quantum yields, suggests a quantum coherent process.