Preparation and characterization of poly(piperazineamide) composite nanofiltration membrane by interfacial polymerization of 3,3 ',5,5 '-biphenyl tetraacyl chloride and piperazine

Most nanofiltration (NF) membranes are composite and have a polyamide thin film prepared by interfacial polymerization. Their performances mainly correlate the structure of the thin film and monomers used for its preparation. In this work, a novel thin-film composite (TFC) nanofiltration membrane was successfully prepared from 3,3',5,5'-biphenyl tetraacyl chloride (mm-BTEC) and piperazine (PIP) through interfacial polymerization. Attenuated reflectance infrared (ATR-IR) and X-ray photoelectronic spectroscopy (XPS) were used to characterize the chemical composition of the membrane surface. The membrane performance was optimized by studying preparation parameters including monomer concentration, reaction time, and pH of aqueous phase.

Structural and vibrational characterization of polyaniline nanofibers prepared from interfacial polymerization

This work deals with the structural and vibrational characterization of PANI nanofibers prepared through interfacial polymerization using different concentrations of HCl aqueous solution. The results were compared to those obtained by PANI prepared through the conventional route. X-ray diffraction and small-angle X-ray scattering techniques showed that high concentrations of HCl solutions used in the preparation of the PANI nanofibers reduce their crystallinity. The increase of regions with granular morphology was also observed in the scanning electron microscopy images. The changes in the resonance Raman spectra from 200 to 500 cm(-1), FTIR spectra, and the EPR data of the PANI nanofibers reveal an increase in the torsion angles of C-ring-N-C-ring segments owing the formation of bipolarons in the PANI backbone higher than the PANI samples prepared by conventional route.

Using different structure types of microemulsions for the preparation of poly(alkylcyanoacrylate) nanoparticles by interfacial polymerization

A phase diagram of the pseudoternary system ethyloleate, polyoxyethylene 20 sorbitan mono-oleate/sorbitan monolaurate and water with butanol as a cosurfactant was prepared. Areas containing optically isotropic, low viscosity one-phase systems were identified and systems therein designated as w/o droplet-, bicontinuous- or solution-type microemulsions using conductivity, viscosity, cryo-field emission scanning electron microscopy and self-diffusion NMR. Nanoparticles were prepared by interfacial polymerization of selected w/o droplet, bicontinuous- or solution-type microemulsions with ethyl-2-cyanoacrylate. Morphology of the particles and entrapment of the water-soluble model protein ovalbumin were investigated. Addition of monomer to the different types of microemulsions (w/o droplet, bicontinuous, solution) led to the formation of nanoparticles, which were similar in size (similar to 250 nm), polydispersity index (similar to 0.13), zeta-potential (similar to-17 mV) and morphology. The entrapment of the protein within these particles was up to 95%, depending on the amount of monomer used for polymerization and the type of microemulsion used as a polymerization template. The formation of particles with similar characteristics from templates having different microstructure is surprising, particularly considering that polymerization is expected to occur at the water-oil interface by base-catalysed polymerization. Dynamics within the template (stirring, viscosity) or indeed interfacial phenomena relating to the solid-liquid interface appear to be more important for the determination of nanoparticle morphology and characteristics than the microstructure of the template system. (c) 2005 Elsevier B.V. All rights reserved.

Effects of polymerization conditions on hydrophilic groups in aromatic polyamide thin films

For polyamide used in reverse osmosis (RO) membranes, the content of pendant acid groups is critical to its performance. In this work, FTIR was used to analyze the acid contents in the polyamide films prepared via interfacial polymerization of trimesic acid trichloride (TMC) in hexane and 1,3-phenylenediamine (MPDA) in water, and the effects of reaction conditions, including monomer concentrations, time, and temperature, were studied. It was found that more pendant acid groups are present in the polyramide film at higher TMC concentrations or lower MPDA concentrations, and longer reaction times and lower temperatures also favor the formation of the free acids. These results can be explained by the monomer diffusion in the interfacial polymerization process. This work may help the design and fabrication of RO membranes with different hydrophilicity and target performance.

Desenvolvimento de microcápsulas contendo as antocianinas presentes no corante do extrato do jambo por polimerização interfacial

The industries of food, medicine and cosmetic apply microencapsulation for many reasons, among them, stabilize the active, control the release of encapsulated and separate incompatible components of the formulation. In this context, microencapsulation techniques have been used in the food industry to provide stable liquid and solid ingredients. Anthocyanins have high antioxidant potential, but they are photodegradable. The challenges are therefore directed to the research for techniques that could make this potential remaining active and bioavailable and could be used as a vehicle for the delivery release of bioactive and micronutrients in appropriate conditions and levels. This work has as main objective to propose a method to encapsulate the anthocyanins in the extract of mountain apple using the interfacial polymerization technique. As well as to define the ideal conditions of temperature and agitation system for this procedure. The microparticles were characterized for size, morphology, active distribution, surface charge, degradation, composition and stability. The results, like particle diameter of 5.94 μm and Zeta potential of 7.03 mV, showed that the technique used to obtain these microparticles was satisfactory and has potential for application in cosmetics and food

Preparation of poly (alkylcyanoacrylate) nanoparticles by polymerization of water-free microemulsions

Phase diagrams of the pseudoternary systems ethyloleate, polyoxyethylene 20 sorbitan mono-oleate/sorbitan monolaurate and propylene glycol with and without butanol as a co-surfactant were prepared. Areas containing optically isotropic, one-phase systems were identified and samples therein designated as droplet, bicontinuous or solution type microemulsions using conductivity, viscosity and self-diffusion NMR. Nanoparticles were prepared by polymerization of selected microemulsions with ethyl-2-cyanoacrylate and the morphology of the particles was investigated. Addition of monomer to all types of microemulsions led to the formation of nanoparticles, which had an average size of 244 +/- 25 nm, an average polydispersity index of 0.15 +/- 0.04 and a zeta-potential of -17 +/- 3 mV. The formation of particles from water-free microemulsions of different types is surprising, particularly considering that polymerization is expected to occur at a water-oil interface by base-catalysed polymerization. It would appear that propylene glycol is sufficiently nucleophilic to initiate the polymerization. The use of water-free microemulsions as templates for the preparation of poly (alkylcyanoacrylate) nanoparticles opens up interesting opportunities for the encapsulation of bioactives which do not have suitable properties for encapsulation on the basis of water-containing microemulsions.

Hypercoiling and hydrophobically associating polymers : interfacial synthesis, surface properties and pharmaceutical applications

The objective of the work described was to identify and synthesize a range of biodegradable hypercoiling or hydrophobically associating polymers to mimic natural apoproteins, such as those found in lung surfactant or plasma apolipoproteins. Stirred interfacial polymerization was used to synthesize potentially biodegradable aromatic polyamides (Mw of 12,000-26,000) based on L-Iysine, L-Iysine ethyl ester, L-ornithine and DL-diaminopropionic acid, by reaction with isophthaloyl chloride. A similar technique was used to synthesize aliphatic polyamides based on L-Iysine ethyl ester and either adipoyl chloride or glutaryl chloride resulting in the synthesis of poly(lysine ethyl ester adipamide) [PLETESA] or poly(lysine ethyl ester glutaramide) (Mw of 126,000 and 26,000, respectively). PLETESA was found to be soluble in both polar and non-polar solvents and the hydrophobic/hydrophilic balance could be modified by partial saponification (66-75%) of the ethyl ester side chains. Surface or interfacial tension/pH profiles were used to assess the conformation of both the poly(isophthalamides) and partially saponified PLETESA in aqueous solution. The results demonstrated that a loss of charge from the polymer was accompanied by an initial fall in surface activity, followed by a rise in activity, and ultimately, by polymer precipitation. These observations were explained by a collapse of the polymer chains into non-surface active intramolecular coils, followed by a transition to an amphipathic conformation, and finally to a collapsed hydrophobe. 2-Dimensional NMR analysis of polymer conformation in polar and non-polar solvents revealed intramolecular associations between the hydrophobic groups within partially saponified PLETESA. Unsaponified PLETESA appeared to form a coiled structure in polar solvents where the ethyl ester side chains were contained within the polymer coil. The implications of the secondary structure of PLETESA and potential biomedical applications are discussed.

Microencapsulation of n-eicosane as energy storage material

For heat energy storage application, polyurea. microcapsules containing phase change material, n-eicosane, were synthesized by using interfacial polymerization method with toluene- 2,4-diisocyanate (TDI) and diethylenetriamine (DETA) as monomers in an emulsion system. Poly(ethylene glycol)octyl-phenyl ether (OP), a nonionic surfactant, was the emulsifier for the system. The experimental result indicates that TDI was reacted with DETA in a mass ratio of 3 to 1. FT-IR spectra confirm the formation of wall material, polyurea, from the two monomers, TDI and DETA. Encapsulation efficiency of n-eicosane is about 75%. Microcapsule of n-eicosane melts at a temperature close to that of n-eicosane, while its stored heat energy varies with core material n-eicosane when wall material fixed. Thermo-gravimetric analysis shows that core material n-eicosane, micro-n-eicosane and wall material polyurea can withstand temperatures up to 130, 170 and 250 degreesC, respectively.

Novel thin-film composite membranes with improved water flux from sulfonated cardo poly(arylene ether sulfone) bearing pendant amino groups

A new class of polymeric amine, namely, sulfonated cardo poly(arylene ether sulfone) (SPES-NH2) was synthesized and used for the preparation of thin-film composite membrane. The TFC membranes were prepared on a polysulfone supporting film through interfacial polymerization with trimesoyl chloride (TMC) solutions and amine solutions containing SPES-NH2 and m-phenylenediamine (MPDA). The resultant membranes were characterized with water permeation performance, chemical structure, hydrophilicity of active layer and membrane morphology including top surface and cross-section.

Polyamide thin film composite membranes prepared from isomeric biphenyl tetraacyl chloride and m-phenylenediamine

Three novel of isomeric tetra-functional biphenyl acid chloride: 3,3',5,5'-biphenyl tetraacyl chloride (mm-BTEC), 2,2',4,4'-biphenyl tetraacyl chloride (om-BTEC), and 2,2',5,5'-biphenyl tetraacyl chloride (op-BTEC) were synthesized, and used as new monomers for the preparation of the thin film composite (TFC) reverse osmosis (RO) membranes through interfacial polymerization with m-phenylenediamine (MPDA). The results of membrane performance test showed that membranes prepared from om-BTEC and op-BTEC had higher flux at the expanse of rejection compared with membranes prepared from mm-BTEC.

Polyamide thin film composite membranes prepared from 3,4',5-biphenyl triacyl chloride, 3,3',5,5'-biphenyl tetraacyl chloride and m-phenylenediamine

Two novel of tri- and tetra-functional biphenyl acid chloride: 3,4',5-biphenyl triacyl chloride (BTRC) and 3,3',5,5'-biphenyl tetraacyl chloride (BTEC), were synthesized, and used as new monomers for the preparations of the thin film composite (TFC) reverse osmosis (RO) membranes. The TFC RO membranes were prepared on a polysulfone supporting film through interfacial polymerization with the two new monomers and m-phenylenediamine (MPD). The membranes were characterized for the permeation properties, chemical composition, d-space between polymer chains, hydrophilicity, membrane morphology including top surface and cross-section. Permeation experiment was employed to evaluate the membranes performance including salt rejection and water flux. The surface structure and chemical composition of membranes were analyzed by attenuated total reflectance infrared (ATR-IR) and X-ray photoelectronic spectroscopy (XPS). The results revealed that the active layer of membranes was composed of highly cross-linked aromatic polyamide with the functional acylamide (-CONH-) bonds. The TFC membranes prepared from biphenyl acid chloride exhibit higher salt rejection compared with that prepared from trimesoyl chloride (TMC) at the expanse of some flux.

Anticorrosion performance of polyaniline nanostructures on mild steel

Different one-dimensional nanostructured polyanilines were synthesized in sulfuric acid solutions by conventional polymerization, interfacial polymerization and direct mixed reaction, respectively. The products were characterized with SEM, UV-vis and FTIR and the anticorrosion performance of products on mild steel were studied using electrochemical measurement in 3.5% NaCl aqueous solution. Results showed that the polyaniline nanofibers synthesized by direct mixed reaction have uniform morphology with diameters of 60-100 nm and more excellent protective properties than conventional aggregated polyaniline. Comparative studies revealed that the nanostructure and morphology of polyaniline could influence its anticorrosion performance. (C) 2010 Elsevier B.V. All rights reserved.

Biotransformations of water insoluble substrates in aqueous, two-phase and encapsulated systems /

The biotransformation of water insoluble substrates by mammalian and bacterial cells has been problematic, since these whole cell reactions are primarily performed in an aqueous environment The implementation of a twophase or encapsulated system has the advantages of providing a low water system along with the physiological environment the cells require to sustain themselves. Encapsulation of mammalian cells by formation of polyamide capsules via interfacial polymerization illustrated that the cells could not survive this type of encapsulation process. Biotransformation of the steroid spironolactone [3] by human kidney carcinoma cells was performed in a substrate-encapsulated system, yielding canrenone [4] in 70% yield. Encapsulation of nitrile-metabolizing Rhodococcus rhodochrous cells using a polyamide membrane yielded leaky capsules, but biotransformation of 2-(4- chlorophenyl)-3-methylbutyronitrile (CPIN) [6] in a free cell system yielded CPIN amide [7] in 40% yield and 94% ee. A two-phase biotransformation of CPIN consisting of a 5:1 ratio of tris buffer, pH 7.2 to octane respectively, gave CPIN acid [8] in 30% yield and 97% ee. It was concluded that Rhodococcus rhodochrous ATCC 17895 contained a nonselective nitrile hydratase and a highly selective amidase enzyme.

Photonen-Aufkonversion in Nanokapseln

Die vorliegende Dissertation zeigt eine erfolgreiche Verknüpfung der Triplett-Triplett-Annihilations-Aufkonversion (TTA-UC) mit möglichen biologischen Anwendungen. Die Grundlage für solche Anwendungen ist ein Transfer der TTA-UC aus seinem üblicherweise verwendeten organischen Medium in eine wässrige Umgebung. Um diesen Transfer zu realisieren, wurden, unter Anwendung der Technik des Miniemulsionsprozesses, in Wasser dispergierte Nanokapseln herstellt. Der Kern dieser Nanokapseln besteht aus einem flüssigen hydrophoben Medium (meist Hexadekan oder Phenylheptadekan), in dem die zur TTA-UC notwendigen Farbstoffe gelöst sind. Dieser flüssige Kern ist vollständig von einer festen Polymerhülle umschlossen und somit isoliert von seiner wässrigen Umgebung. Es wurden insgesamt drei Generationen solcher Nanokapseln hergestellt, die sich hauptsächlich im Herstellungsprozess, aber auch beim Material von Kern und Hülle unterscheiden. Mittels dieser Variationen konnten die Nanokapseln in Bezug auf Effizienz, Anregungswellenlänge und Sauerstoffempfindlichkeit optimiert werden. Bei der ersten Generation wurde die radikalische Miniemulsionspolymerisation zur Kapselbildung verwendet. Die zweite Generation wurde durch die Kombination des Lösungsmittelverdampfungsprozesses mit dem Miniemulsionsprozess entwickelt und liefert somit eine alternative Möglichkeit der Kapselbildung unter milden Reaktionsbedingungen, was eine uneingeschränkte Auswahl der UC-Farbstoffpaare ermöglicht. Durch den Einsatz unterschiedlicher Sensitizer konnte die Anregungswellenlänge der TTA-UC in den roten und in den nahen Infrarot-Bereich des sichtbaren Spektrums verschoben werden. Diese Verschiebung ist im biologischen Anwendungsbereich von enormer Bedeutung, da dort eine Überlappung mit dem natürlichen optischen Fenster von menschlicher Haut und Gewebe stattfindet. Dies reduziert die Streuung der Anregungsquelle im zu untersuchende Medium und ermöglicht hohe Eindringtiefen. Mit den Kapseln der zweiten Generation wurde zum ersten Mal TTA-UC in lebenden HeLa-Zellen (Krebszellen) und MSCs (Mesenchymale Stammzellen) nachgewiesen. Die verzögerte Fluoreszenz aus den Zellen wurde mit biologischen Standardverfahren, sowohl mit der Durchflusszytometrie (FACS) als auch am cLSM nachgewiesen. Besondere Vorteile gegenüber direkter Fluoreszenz konnten bei der Bildgebung von Zellen erreicht werden. Die relativ energiearme Anregungswellenlänge und die dazu anti-Stokes verschobene, detektierte verzögerte UC-Fluoreszenz lieferte eine bessere Bildqualität und eine sehr geringe Phototoxizität der Zellen. Die Kapseln der dritten Generation zeichnen sich durch ihre anorganische, tetraedrisch verknüpfte SiO2-Hülle aus und wurden mittels einer Grenzflächenreaktion (Sol-Gel-Prozess) in Miniemulsion hergestellt. Diese Kapseln weisen im Vergleich zu den Polymernanokapseln eine bessere UC-Effizienz auf und sind zusätzlich stabiler und robuster.

Saccharide based nanocapsules - From monomer building blocks to improved capsules properties

In dieser Arbeit wurde der vielfältige Nutzen von Kohlenhydraten in Nanokapsel Systemen untersucht. Drei verschiedene Nanokapsel-Typen wurden durch Reaktion an der Grenzfläche von inversen Miniemulsionen hergestellt. Es wurde gezeigt, dass die Kohlenhydrate nach Modifizierung als Monomer an der Kapselbildung teilnehmen können, oder zur Erhöhung der Sensitivität eines verkapselten Kontrastmittels beitragen können. Im Folgenden werden die Ergebnisse der einzelnen Projekte zusammengefasst. Eine neuartige Grenzflächen-Synthese zur Herstellung von Nanokapseln wurde entwickelt und untersucht. Bei der Reaktion handelt es sich um eine Ruthenium katalysierte Olefin-Kreuzmetathese, welche für die Reaktion an der Grenzfläche angepasst wurde. Als wasserlösliches Macromonomer wurde Dextranacrylat synthetisiert. Der Reaktionspartner war ein öl-löslichen Phosphoester (Phenyldi(undec-10-en-1-yl)phosphat). Anhand von NMR-Spektren wurde gezeigt, dass die Kapselbildung auf Olefin Kreuzmetathese beruht. Im Vergleich zu konventionellen Estern haben Phosphorester eine weitere Möglichkeit zur chemischen Funktionalisierung. Dies wurde exemplarisch durch die Verwendung von fluoreszenzmarkierten Phosphoestern gezeigt. Die Markierung wurde verwendet, um die pH-induzierte Abbaubarkeit der Nanokapseln mittels Fluoreszenz-Korrelations-Spektroskopie zu beobachten. Ziel des zweiten Projekts war es, Nanostrukturen zu entwickeln, um Infektionen mit Antibiotika-resistenten Bakterien lokal zu behandeln. Dazu wurden mit Dextranmethacrylat vernetzte Poly(acrylamid) basierte Nanogele synthetisiert und Zinknitrat zugesetzt. Die Synthese der Nanogele wurde erweitert, um durch Vernetzung freier Alkoholgruppen mit Toluoldiisocyanat eine Kapselschale zu erhalten. Die Schalenbildung spiegelte sich in einer geringeren Quellbarkeit der Gel- Schale-Hybride wieder. Die erhaltenen Gel-Schale-Hybride waren in der Lage das Wachstum von zwei Methicillin-resistenten Bakterienstämmen (S. aureus) zu unterdrücken und verzögern. Die synthetisierten Hybridstrukturen könnten in der Beschichtung von Wundauflagen Verwendung finden, um bakterielle Infektionen lokal und direkt nach Ausbruch zu behandeln. Ziel des dritten Projektes war es, die wichtigen Parameter in der Herstellung von Nanokapseln mit hoher Kontrastmittel Sensitivität zu identifizieren. Relaxivität/Signalsensitivität des Kontrastmittels ist von großer Bedeutung für die Bildgebung mittels MRI, dies kann durch die Begrenzung der Mobilität des Kontrastmittels erreicht werden. Aufgrund seiner hohen Komplexstabilität und seiner klinischen Bedeutung wurde das Kontrastmittel Gadobutrol für die Verkapselung verwendet. Das Kontrastmittel wurde in Polyharnstoff-Kapseln eingeschlossen, die durch einen inversen Miniemulsion-Prozess hergestellt wurden. Um die Viskosität im Inneren der Nanokapsel zu erhöhen, wurden zusätzlich Saccharose, Dextran und Polyacrylsäure verkapselt. In Gegenwart von Saccharose konnte die Relaxivität verdoppelt werden. Dies gründet sich vermutlich auf einem Second-sphere Effekt der Saccharose, einer auf Wasserstoffbrückenbindungen beruhende Interaktion von Kontrastmittel und Saccharose.