Processamento e caracterização mecânica e metalográfica de compósitos adiamantados à base de cobre-níquel obtidos por hot pressing

Dissertação de mestrado em Engenharia de Materiais

Preparation of Ni-Ti-Mo and Ni-Ti-Mo-Zr Alloys by High-Energy Ball Milling and Subsequent Hot Pressing

This work discusses on the preparation of Ni-45Ti-5Mo, Ni-40Ti-10Mo and Ni-46Ti-2Mo-2Zr (at-%) alloys by high-energy ball milling and hot pressing, which are potentially attractive for dental and medical applications. The milling process was performed in stainless steel balls (19mm diameter) and vials (225 mL) using a rotary speed of 300rpm and a ball-to-powder weight ratio of 10:1. Hot pressing under vacuum was performed in a BN-coated graphite crucible at 900 degrees C for 1 h using a load of 20 MPa. The milled and hot-pressed materials were characterized by X-ray diffraction, electron scanning microscopy, and electron dispersive spectrometry. Peaks of B2-NiTi and Ni4Ti3 were identified in XRD patterns of Ni-45Ti-5Mo, Ni-40Ti-10Mo and Ni-46Ti-2Mo-2Zr powders milled for 1h. The NiTi compound dissolved small Mo amounts lower than 4 at%, which were measured by EDS analysis. Moreover, it was identified the existence of an unknown Mo-rich phase in microstructures of the hot-pressed Ni-Ti-Mo alloys.

alpha-SiAlON-SiC composites obtained by gas-pressure sintering and hot-pressing

The objective of this work was the obtaining in situ of alpha-SiAlON-SiC composite, using an alternative rare-earth oxide mixture, RE2O3, as sintering additive, by two different sintering processes. As sintering additive, 20 vol.% of AlN-RE2O3 in a molar ratio of 90: 10 was mixed to the alpha-Si3N4 powder. In the Si3N4-AlN-RE2O3 powder mixture, 0, 10, 15 and 20wt.% of SiC were added. The powder batches were milled, dried and compacted by cold isostatic pressing. Two different sintering processes were used: gas-pressure sintering at 1950 degrees C for 1 h under 1.5 MPa of N-2 atmosphere, or uniaxial hot-pressing at 1750 degrees C, for 30 min under pressure of 20 MPa. The sintered samples were characterized by X-ray diffraction, scanning electron microscopy and mechanical properties. XRD patterns indicate only alpha-SiAlON (alpha') and beta-SiC as crystalline phases. It was observed that the SiC addition did not influence the alpha-SiAlON formation, although the growth of elongated alpha'-grains is substantially decreased. The hot-pressed composites presented better mechanical properties, exhibiting fracture toughness of 5 MPa m(1/2) and hardness around 21.5 GPa. (c) 2007 Elsevier B.V. All rights reserved.

Hot-pressing of electrolytic, dehydrided, and calcium-reduced thorium powders /

"Contract AT-30-1 GEN-366."

Mechanical properties and porosity of dental glass-ceramics hot-pressed at different temperatures

The objective of this work was to evaluate biaxial-flexural-strength (σf), Vickers hardness (HV), fracture toughness (K Ic), Young's modulus (E), Poisson's ratio (ν) and porosity (P) of two commercial glass-ceramics, Empress (E1) and Empress 2 (E2), as a function of the hot-pressing temperature. Ten disks were hot-pressed at 1065, 1070, 1075 and 1080 °C for E1; and at 910, 915, 920 and 925 °C for E2. The porosity was measured by an image analyzer software and s f was determined using the piston-on-three-balls method. K Ic and HV were determined by an indentation method. Elastic constants were determined by the pulse-echo method. For E1 samples treated at different temperatures, there were no statistical differences among the values of all evaluated properties. For E2 samples treated at different temperatures, there were no statistical differences among the values of σf, E, and ν, however HV and K Ic were significantly higher for 910 and 915 °C, respectively. Regarding P, the mean value obtained for E2 for 925 °C was significantly higher compared to other temperatures.

Hot-pressed 9.5/65/35 PLZT prepared by the polymeric precursor method

A 9.5/65/35 PLZT ceramic with a Pb-0.905 La-0.095 (Zr-0.65 Ti-0.35)(0.976) O-3 + 35 w% PbO formula was prepared using the Pechini method for powder preparation and two-step sintering in an oxygen atmosphere. Thr first step consisted of sintering at 1200 degrees C for 4 h with slow heating and cooling rates. The second step consisted of hot pressing at 1200 degrees C for 3 h, with slow heating and cooling rates and pressing pressures of 20 MPa (initial pressure) and 40 MPa (at sintering temperature). Investigations were made of the powder phase formation and powder morphology, i.e. The structure of sintered and hot-pressed PLZT ceramics. SEM microstructural analyses were carried out on the sintering and hot-pressing processes. (C) 2000 Elsevier B.V. Ltd and Techna S.r.l. All rights reserved.

Tribocorrosion behaviour of hot pressed CoCrMo−Al2O3 composites for biomedical applications

Alumina/alumina wear couple can lower the wear rates and thus metallic ion releasing on load bearing metallic implant materials. However, the low fracture toughness of ceramics is still a major concern. Therefore, the present study aims to process and to triboelectrochemically characterise the 5 and 10 vol.-%Al2O3 reinforced CoCrMo matrix composites. Corrosion and tribocorrosion behaviour of the composites were investigated in 8 g L−1 NaCl solution at body temperature. Corroded and worn surfaces were investigated by a field emission gun scanning electron microscope equipped with energy dispersive X-ray spectroscopy. After tribocorrosion experiments, wear rates were calculated using a profilometer. Results suggest that Al2O3 particle addition decreased the tendency of CoCrMo alloy to corrosion under both static and tribocorrosion conditions. However, no significant influence on the corrosion and wear rates was observed in composites mainly due to increased porosity and insufficient matrix/reinforcement bonding.

Modification of surface properties of Ti-16Si-4B powder alloy by plasma immersion ion implantation

Results of the surface modification of Ti-16Si-4B powder alloy by nitrogen ion implantation are presented, together with the experimental description of the preparation of that powder by high-energy ball milling and hot pressing. The phase structure, chemical composition and morphology of sample surfaces were observed by utilizing X-ray diffractometer (XRD), atomic force microscope (AFM) and scanning electron microscopy (SEM). A tribological characterization was carried out with a ball-on-disc tribometer and an SEM. Friction coefficient is compared with the one obtained for Ti-6Al-4V alloy and the wear scars characterized by SEM/EDS (energy dispersive spectroscopy). The concentration profile of the detected elements have been investigated using Auger electron spectroscopy (AES) depth profiling. Our results show that a shallow implanted layer of oxygen and nitrogen ions were obtained at the Ti-16Si -4B alloy surface, sufficient to modify slightly its tribological properties. Crown Copyright (C) 2011 Published by Elsevier Ltd. All rights reserved.

Material properties and nondestructive evaluation of laminated veneer lumber (LVL) made from Pinus oocarpa and P. kesiya

This study aimed at evaluating the mechanical, physical and biological properties of laminated veneer lumber (LVL) made from Pinus oocarpa Schiede ex Schltdl (PO) and Pinus kesiya Royle ex Gordon (PK) and at providing a nondestructive characterization thereof. Four PO and four PK LVL boards from 22 randomly selected 2-mm thickness veneers were produced according to the following characteristics: phenol-formaldehyde (190 g/m(2)), hot-pressing at 150A degrees C for 45 min and 2.8 N/mm(2) of specific pressure. After board production, nondestructive evaluation was conducted, and stress wave velocity (v (0)) and dynamic modulus of elasticity (E (Md) ) were determined. The following mechanical and physical properties were then evaluated: static bending modulus of elasticity (E (M) ), modulus of rupture (f (M) ), compression strength parallel to grain (f (c,0)), shear strength parallel to glue-line (f (v,0)), shear strength perpendicular to glue-line (f (v,90)), thickness swelling (TS), water absorption (WA), and permanent thickness swelling (PTS) for 2, 24, and 96-hour of water immersion. Biological property was also evaluated by measuring the weight loss by Trametes versicolor (Linnaeus ex Fries) Pilat (white-rot) and Gloeophyllum trabeum (Persoon ex Fries.) Murrill (brown-rot). After hot-pressing, no bubbles, delamination nor warping were observed for both species. In general, PK boards presented higher mechanical properties: E (M) , E (Md) , f (M) , f (c,0) whereas PO boards were dimensionally more stable, with lower values of WA, TS and PTS in the 2, 24, and 96-hour immersion periods. Board density, f (v,0), f (v,90) and rot weight loss were statistically equal for PO and PK LVL. The prediction of flexural properties of consolidated LVL by the nondestructive method used was not very efficient, and the fitted models presented lower predictability.

Characterization tests for insulation boards made from corn cob and natural glues

In recent years there has been a growing interest in developing news solutions for more ecologic and efficient construction, including natural, renewable and local materials, thus contributing in the search for more efficient, economic and environmentally friendly construction. Several authors have assessed the possibility of using various agricultural sub products or wastes, as part of the effort of the scientific community to find alternative and more ecologic construction materials. Corn cob is an agricultural waste from a very important worldwide crop. Natural glues are made from natural materials, non-mineral, that can be used as such or after some modifications to achieve the behaviour and performance required. Two examples of these natural glues are casein and wheat flour-based glues that were used in the present study. Boards with different compositions were manufactured, having as variables the type of glue, the dimension of the corn cob particles and the features of the pressing process. The tests boards were characterized with physical and mechanical tests, such as thermal conductivity (λ) with a ISOMET 2104 and 60 mm diameter contact probe, density (ρ) based on EN 1602:2013, surface hardness (SH) with a PCE Shore A durometer, surface resistance (SR) with a PROCEQ PT pendular sclerometer, bending behaviour (σ) based on EN 12089:2013, compression behaviour (σ10) based on EN 826:2013 and resilience (R) based on EN 1094-1:2008, with a Zwick Rowell bending equipment with 2 kN and 50 kN load cells (Fig. 1), dynamic modulus of elasticity (Ed) with a Zeus Resonance Meter equipment (Fig. 5) based on NP EN 14146:2006 and water vapour permeability (δ) based on EN 12086:2013. The various boards produced were characterized according to the tests and the ones with the best results were C8_c8 (casein glue, grain size 2,38-4,76 mm, cold pressing for 8 hours), C8_c4 (casein glue, grain size 2,38-4,76 mm, cold pressing for 4 hours), F8_h0.5 (wheat flour glue, grain size 2,38-4,76 mm, hot pressing for 0,5 hours), FEV8_h0.5 (wheat flour, egg white and vinegar glue, grain size 2,38-4,76 mm, hot pressing for 0,5 hours) and FEVH68_c4 (wheat flour, egg white, vinegar and 6 g of sodium hydroxide glue, grain size 2,38-4,76 mm, cold pressing for 4 hours). Taking into account the various boards produced and respective test results the type of glue and the pressure and pressing time are very important factors which strongly influence the final product. The results obtained confirmed the initial hypotheses that these boards have potential as a thermal and, eventually, acoustic insulation material, to use as coating or intermediate layer on walls, floors or false ceilings. This type of board has a high mechanical resistance when compared with traditional insulating materials.The integrity of these boards seems to be maintained even in higher humidity environments. However, due to biological susceptibility and sensitivity to water, they would be more adequate for application in dry interior conditions.

Otimização dos parâmetros de processamento em Laser Melting

Dissertação de mestrado integrado em Engenharia Mecânica

Wear of PEEK-Ti6Al4V systems under micro-abrasion and linear sliding conditions

Dissertação de mestrado integrado em Engenharia Biomédica

Processamento e caracterização de compósitos de Ti-HAP para aplicações biomédicas

Dissertação de mestrado integrado em Engenharia de Materiais

Levyteollisuuden energia-, kustannus- ja ympäristövaikutukset

Kuluvien vuosien aikana ei ole tehty kattavia tutkimuksia levyteollisuuden sähkönkulutuksista, joten on aika selvittää suurimpien sähkökäyttöjen kulutukset sekä muodostaa tutkittaville tehtaille energiataseet. Tutkittavia tehtaita ovat OSB- ja lastulevytehtaat. Yksittäisten sähkömoottoreiden kulutukset saadaan selville käyttämällä hyväksi teoreettisia lähteitä, kenttä-ja laboratoriotutkimusta. Ympäristölainsäädäntö ja siihen kiinteästi liittyvä lupakäytäntö muodostavat levyteollisuudelle yhden viimeaikojen suurimmista haasteista. Tulevaisuudessa lainsäädäntö tulee vielä entisestäänkin kiristymään. Euroopan ympäristölainsäädäntö perustuu pitkälti yhtenäislupadirektiiviin eli IPPC-direktiiviin. Direktiivin keskeinen osa on ympäristöluvan hankkiminen, koska teollista toimintaa ei voi harjoittaa ilman hyväksyttyä viranomaisen lupaa. Lupa myös velvoittaa toiminnanharjoittajan käyttämään parasta käyttökelpoista tekniikkaa päästöjen kontrolloinnissa. Yhdysvalloissa parhaan käyttökelpoisen tekniikan (BAT) vaatimus on sisälletty ympäristövirasto EPA:n MACT-standardeihin. Levyteollisuuden tehtaista syntyvät päästöt ovat hyvin samankaltaisia. Tehtaista on helposti erotettavissa kaksi suurta päästölähdettä, joita ovat kuivaus ja kuumapuristus. Merkittävimpiä päästöjä ovat haihtuvat orgaaniset yhdisteet, hiukkaset, typen oksidit, hiilimonoksidi ja rikkidioksidit. Työn loppuosa on varattu tuotantojen kustannusvaikutusten ja tunnuslukujen tarkasteluille. Saatavilla tiedoilla on keskeinen rooli tehtaiden jokapäiväisessä toiminnassa. Analysoinnin tarpeeseen vaikuttaa osaltaan nykyisen toimintaympäristön muutosherkkyys ja levymarkkinoiden kireä kilpailutilanne.

Ekologisen kuorilevyn valmistaminen puunjalostusteollisuuden sivutuotteista

Puunjalostusteollisuudessa syntyy huomattavia määriä sivutuotteita, joiden hyödyntäminen on vielä vajavaista. Sahajauhon ja puukuoren pääasiallinen käyttö rajoittuu energiantuotantoon eli polttamiseen voimalaitoksissa. Selostettavassa tutkimustyössä, joka on tehty Lappeenrannan teknillisen yliopiston puunjalostustekniikan levylaboratoriossa, on pyritty selvittämään kotimaisten kuusi-, mänty- ja koivukuorten käyttömahdollisuuksia raaka-aineina lastulevyn tapaan ns. ekologisen kuorilevyn valmistamisessa, mutta ilman liimaa. Tutkimusmateriaalina käytettiin puunjalostusteollisuudesta hankittua tuoretta kuusen ja männyn rumpukuorintajätettä sekä koivun roottorikuorintajätettä, joista kukin raaka-aine pienennettiin kahteen eri partikkelikokoon käyttäen oksasilppuria ja vasaramyllyä. Raaka-ainemäärät mitattiin ja kaadettiin viiran päällä olevaan puusta valmistettuun muottiin ja muotin poisnostamisen jälkeen levyaihio puristettiin 1-välikuumapuristimessa sykleittäin. Valmistetut kuorilevyt olivat 1 -kerroksisia. Koelevyistä tutkittiin kosteuspitoisuus, tilavuuspaino, taivutuslujuus ja Brinell -kovuus.Saadut tulokset osoittavat, että kuusen, männyn ja koivun kuoresta voidaan valmistaa kuorilevyä ilman liima-ainetta, sillä puukuoren sisältämät omat liimaavuutta parantavat uuteaineet antavat riittävän vaikutuksen kuorilevyn rakenteen stabiloimiseksi. Tällaisen kuorilevyn taivutuslujuus on kuitenkin huomattavasti heikompi kuin puulastulevyllä. Kaikki jauhetusta raaka-aineesta sekä pelkästään silputusta koivuraaka-aineesta valmistetut kuorilevyt täyttävät taivutuslujuuden osalta kuitenkin huokoiselle, A-lujuusluokan standardi-kuitulevylle asetetut vaatimukset. Tarkasteltaessa eri raaka-aineista valmistettujen levyjen ominaisuuksia, voidaan todeta, että tilavuuspainoltaan suurinta sekä kovuudeltaan ja taivutuslujuudeltaan parasta levyä saadaan valmistettua jauhetusta koivukuoresta. Jokaisen valmistetun kuorilevyn kovuusarvo ylittää Suomen johtavan lastulevyn valmistajan lastulevyn kovuusarvon lukuun ottamatta pelkästään silputuista kuusi- ja mäntykuorista valmistettuja levyjä.Vaikka tulokset ovat suuntaa-antavia, osoittavat ne selvästi millaisia mahdollisuuksia tarjoaa puun kuoren tai sahajauhon käyttäminen lastulevyn tapaan valmistettavien levyjen raaka-aineena. Koko tutkimuskenttä on tässä käsiteltävänä olevalla alueella varsin laaja, ja tässä tutkimuksessa selvitetyt asiat ovat siitä vain pieni osa antaen kuitenkin suunnan useille tärkeille jatkossa selvitettäville asioille. Näistä mainittakoon mm. ekologisen levyn jatkojalostus ja tuotesuunnittelu, levyn valmistuksen taloudellisuus ja tuotteiden markkinointi, kuorilevyn valmistusprosessin kehittäminen sekä eri raaka-aineyhdistelmien kokeilu kuorilevyn raaka-aineena.