The performance of a cathodic protection system in reinforced concrete structure: Monitoring and Service Life Modelling

The use of cathodic protection in reinforced concrete is becoming increasingly common with such systems being installed on a number of structures throughout the United Kingdom and Ireland. However the prescribed design lives (or service life) of each cathodic protection system vary widely. The aim of this project was to assess the effectiveness of a sacrificial anode cathodic protection system and to predict its design life through a series of laboratory based experiments. The experimental plan involved casting a number of slabs which represented a common road bridge structure. The corrosion of the steel within the experimental slabs was then accelerated prior to installation of a cathodic protection system. During the experiment corrosion potential of the steel reinforcement was monitored using half-cell measurement. Additionally the current flow between the cathodic protection system and the steel reinforcement was recorded to assess the degree of protection. A combination of theoretical calculations and experimental results were then collated to determine the design life of this cathodic protection system. It can be concluded that this sacrificial anode based cathodic protection system was effective in halting the corrosion of steel reinforcement in the concrete slabs studied. Both the corrosion current and half-cell potentials indicated a change in passivity for the steel reinforcement once sacrificial anodes were introduced. The corrosion current was observed to be sensitive to the changes to the exposure environment. Based on the experimental variables studied the design life of this sacrificial anode can be taken as 26 to 30 years.

Detection of Bridge Dynamic Parameters using an Instrumented Vehicle

Highway structures such as bridges are subject to continuous degradation primarily due to ageing and environmental factors. A rational transport policy requires the monitoring of this transport infrastructure to provide adequate maintenance and guarantee the required levels of transport service and safety. In Europe, this is now a legal requirement - a European Directive requires all member states of the European Union to implement a Bridge Management System. However, the process is expensive, requiring the installation of sensing equipment and data acquisition electronics on the bridge. This paper investigates the use of an instrumented vehicle fitted with accelerometers on its axles to monitor the dynamic behaviour of bridges as an indicator of its structural condition. This approach eliminates the need for any on-site installation of measurement equipment. A simplified half-car vehicle-bridge interaction model is used in theoretical simulations to test the possibility of extracting the dynamic parameters of the bridge from the spectra of the vehicle accelerations. The effect of vehicle speed, vehicle mass and bridge span length on the detection of the bridge dynamic parameters are investigated. The algorithm is highly sensitive to the condition of the road profile and simulations are carried out for both smooth and rough profiles

Monitoring Bridge Dynamic Behaviour using an Instrumented Two Axle Vehicle

Highway structures such as bridges are subject to continuous degradation primarily due to ageing, loading and environmental factors. A rational transport policy must monitor and provide adequate maintenance to this infrastructure to guarantee the required levels of transport service and safety. Increasingly in recent years, bridges are being instrumented and monitored on an ongoing basis due to the implementation of Bridge Management Systems. This is very effective and provides a high level of protection to the public and early warning if the bridge becomes unsafe. However, the process can be expensive and time consuming, requiring the installation of sensors and data acquisition electronics on the bridge. This paper investigates the use of an instrumented 2-axle vehicle fitted with accelerometers to monitor the dynamic behaviour of a bridge network in a simple and cost-effective manner. A simplified half car-beam interaction model is used to simulate the passage of a vehicle over a bridge. This investigation involves the frequency domain analysis of the axle accelerations as the vehicle crosses the bridge. The spectrum of the acceleration record contains noise, vehicle, bridge and road frequency components. Therefore, the bridge dynamic behaviour is monitored in simulations for both smooth and rough road surfaces. The vehicle mass and axle spacing are varied in simulations along with bridge structural damping in order to analyse the sensitivity of the vehicle accelerations to a change in bridge properties. These vehicle accelerations can be obtained for different periods of time and serve as a useful tool to monitor the variation of bridge frequency and damping with time.

A review of road structure data in six European countries

The European Union has expanded significantly in recent years. Sustainable trade within the Union, leading to economic growth to the benefit of the ‘old’ and ‘new’ member states is thus extremely important. The road infrastructure is strategic and vital to such development since an uneven transport infrastructure, in terms of capacity and condition, has the potential to reinforce uneven development trends and hinder economic convergence of old and new member states. In the decades since their design and construction, loading conditions have significantly changed for many major highway infrastructure elements/networks owing primarily to increased freight volumes and vehicle sizes. This, coupled with the gradual deterioration of a significant number of highway structures due to their age, and the absence of a pan-European assessment framework, can be expected to affect the smooth functioning of the infrastructure in its as-built condition. Increased periods of reduced flow can be expected owing to planned and unplanned interventions for repair/rehabilitation. This paper reports the findings of a survey regarding the current status of the highway infrastructure elements in six countries within the European Union as reported by the owners/operators. The countries surveyed include a cross-section of ‘existing’ older countries and ‘new’ member states. The current situations for bridges, culverts, tunnels and retaining walls are reported, along with their potential replacement costs. The findings act as a departure point for further studies in support of a centralised and/or synchronised EU approach to infrastructure maintenance management. Information in the form presented in this paper is central to any future decision-making frameworks in terms of trade route choice and operations, monetary investment, optimised maintenance, management and rehabilitation of the built infrastructure and the economic integration of the newly joined member states.

Standard specifications for highway bridges and incidental structures.

Mode of access: Internet.

A pictorial report on highway bridges and structures in the District of Columbia.

Mode of access: Internet.

Benchmark Control Problem for Highway Bridge based on FLC

Fuzzy logic control (FLC) systems have been applied as an effective control system in various fields, including vibration control of structures. The advantage of this approach is its inherent robustness and ability to handle non‐linearities and uncertainties in structural behavior and loading. The study evaluates the three‐dimensional benchmark control problem for a seismically excited highway bridge using an ANFIS driven hydraulic actuators. An ANN based training strategy that considers both velocity and acceleration feedback together with a fuzzy logic rule base is developed. Present study needs only 4 accelerometers and 4 fuzzy rule bases to determine the control force, instead of 8 accelerometers and 4 displacement transducers used in the benchmark study problem. The results obtained are better than that obtained from the benchmark control algorithm.

Embodied Energy and Gas Emissions of Retaining Wall Structures

The embodied energy (EE) and gas emissions of four design alternatives for an embankment retaining wall system are analyzed for a hypothetical highway construction project. The airborne emissions considered are carbon dioxide (CO 2), methane (CH 4), nitrous oxide (N 2O), sulphur oxides (SO X), and nitrogen oxides (NO X). The process stages considered in this study are the initial materials production, transportation of construction machineries and materials, machinery operation during installation, and machinery depreciations. The objectives are (1) to determine whether there are statistically significant differences among the structural alternatives; (2) to understand the relative proportions of impacts for the process stages within each design; (3) to contextualize the impacts to other aspects in life by comparing the computed EE values to household energy consumption and car emission values; and (4) to examine the validity of the adopted EE as an environmental impact indicator through comparison with the amount of gas emissions. For the project considered in this study, the calculated results indicate that propped steel sheet pile wall and minipile wall systems have less embodied energy and gas emissions than cantilever steel tubular wall and secant concrete pile wall systems. The difference in CO 2 emission for the retaining wall of 100 m length between the most and least environmentally preferable wall design is equivalent to an average 2.0 L family car being driven for 6.2 million miles (or 62 cars with a mileage of 10,000 miles/year for 10 years). The impacts in construction are generally notable and careful consideration and optimization of designs will reduce such impacts. The use of recycled steel or steel pile as reinforcement bar is effective in reducing the environmental impact. The embodied energy value of a given design is correlated to the amount of gas emissions. © 2011 American Society of Civil Engineers.

National Conference on Wood Transportation Structures /

Cover title.

Refinement of finite element analysis of automobile structures under crash loading. Volume I. Summary final report.

National Highway Traffic Safety Administration, Washington, D.C.

Mathematical simulation models for crashworthiness qualification of motor vehicle structures. Phase I. Final report.

National Highway Safety Bureau, Washington, D.C.

Feasibility study of ballistic cutting of vehicle structures. Final report.

National Highway Safety Bureau, Washington, D.C.

Laboratory evaluation of existing breakaway structures. Volume I: executive summary. Final report.

Federal Highway Administration, Office of Research, Washington, D.C.