Control mechanisms for gas hydrate production by depressurization in different scale hydrate reservoirs

The methane hydrate was formed in a pressure vessel 38 mm in id and 500 mm in length. Experimental works on gas production from the hydrate-bearing core by depressurization to 0.1, 0.93, and 1.93 MPa have been carried out. The hydrate reservoir simulator TOUGH-Fx/Hydrate was used to simulate the experimental gas production behavior, and the intrinsic hydration dissociation constant (K-0) fitted for the experimental data was on the order of 104 mol m(-2) Pa-1 s(-1), which was one order lower than that of the bulk hydrate dissociation. The sensitivity analyses based on the simulator have been carried out, and the results suggested that the hydrate dissociation kinetics had a great effect on the gas production behavior for the laboratory-scale hydrate-bearing core. However for a field-scale hydrate reservoir, the flow ability dominated the gas production behavior and the effect of hydrate dissociation kinetics on the gas production behavior could be neglected.

Power management and power flow control with back-to-back converters in a utility connected microgrid

This paper proposes a method for power flow control between utility and microgrid through back-to-back converters, which facilitates desired real and reactive power flow between utility and microgrid. In the proposed control strategy, the system can run in two different modes depending on the power requirement in the microgrid. In mode-1, specified amount of real and reactive power are shared between the utility and the microgrid through the back-to-back converters. Mode-2 is invoked when the power that can be supplied by the DGs in the microgrid reaches its maximum limit. In such a case, the rest of the power demand of the microgrid has to be supplied by the utility. An arrangement between DGs in the microgrid is proposed to achieve load sharing in both grid connected and islanded modes. The back-to-back converters also provide total frequency isolation between the utility and the microgrid. It is shown that the voltage or frequency fluctuation in the utility side has no impact on voltage or power in microgrid side. Proper relay-breaker operation coordination is proposed during fault along with the blocking of the back-to-back converters for seamless resynchronization. Both impedance and motor type loads are considered to verify the system stability. The impact of dc side voltage fluctuation of the DGs and DG tripping on power sharing is also investigated. The efficacy of the proposed control ar-rangement has been validated through simulation for various operating conditions. The model of the microgrid power system is simulated in PSCAD.

Active flow control bump design using hybrid Nash-game coupled to evolutionary algorithms

In this paper, the optimal design of an active flow control device; Shock Control Bump (SCB) on suction and pressure sides of transonic aerofoil to reduce transonic total drag is investigated. Two optimisation test cases are conducted using different advanced Evolutionary Algorithms (EAs); the first optimiser is the Hierarchical Asynchronous Parallel Evolutionary Algorithm (HAPMOEA) based on canonical Evolutionary Strategies (ES). The second optimiser is the HAPMOEA is hybridised with one of well-known Game Strategies; Nash-Game. Numerical results show that SCB significantly reduces the drag by 30% when compared to the baseline design. In addition, the use of a Nash-Game strategy as a pre-conditioner of global control saves computational cost up to 90% when compared to the first optimiser HAPMOEA.

Active power flow control in a distribution system using discontinuous voltage controller

stract This paper proposes a hybrid discontinuous control methodology for a voltage source converter (VSC), which is used in an uninterrupted power supply (UPS) application. The UPS controls the voltage at the point of common coupling (PCC). An LC filter is connected at the output of the VSC to bypass switching harmonics. With the help of both filter inductor current and filter capacitor voltage control, the voltage across the filter capacitor is controlled. Based on the voltage error, the control is switched between current and voltage control modes. In this scheme, an extra diode state is used that makes the VSC output current discontinuous. This diode state reduces the switching losses. The UPS controls the active power it supplies to a three-phase, four-wire distribution system. This gives a full flexibility to the grid to buy power from the UPS system depending on its cost and load requirement at any given time. The scheme is validated through simulation using PSCAD.

Fair flow control of ABR service by per-VC virtual queuing

In this paper, a rate-based flow control scheme based upon per-VC virtual queuing is proposed for the Available Bit Rate (ABR) service in ATM. In this scheme, each VC in a shared buffer is assigned a virtual queue, which is a counter. To achieve a specific kind of fairness, an appropriate scheduler is applied to the virtual queues. Each VC's bottleneck rate (fair share) is derived from its virtual cell departure rate. This approach of deriving a VC's fair share is simple and accurate. By controlling each VC with respect to its virtual queue and queue build-up in the shared buffer, network congestion is avoided. The principle of the control scheme is first illustrated by max–min flow control, which is realised by scheduling the virtual queues in round-robin. Further application of the control scheme is demonstrated with the achievement of weighted fairness through weighted round robin scheduling. Simulation results show that with a simple computation, the proposed scheme achieves the desired fairness exactly and controls network congestion effectively.

Network flow-control using asynchronous stochastic approximation

We propose several stochastic approximation implementations for related algorithms in flow-control of communication networks. First, a discrete-time implementation of Kelly's primal flow-control algorithm is proposed. Convergence with probability 1 is shown, even in the presence of communication delays and stochastic effects seen in link congestion indications. This ensues from an analysis of the flow-control algorithm using the asynchronous stochastic approximation (ASA) framework. Two relevant enhancements are then pursued: a) an implementation of the primal algorithm using second-order information, and b) an implementation where edge-routers rectify misbehaving flows. Next, discretetime implementations of Kelly's dual algorithm and primaldual algorithm are proposed. Simulation results a) verifying the proposed algorithms and, b) comparing the stability properties are presented.

Knowledge Transfer within Western Multinationals' Subsidiary Units in China and Finland - The Impact of Headquarter Control Mechanisms, Subsidiary Location and Social Capital (summary section only)

It is suggested that the ability and practices of how the multinational corporation (MNC) manages knowledge transfer among its geographically dispersed subsidiary units are crucial for the building and development of firm competitive advantage. However, cross-border transfer of valuable organizational knowledge is likely to be problematic and laborious, especially within diversified and differentiated MNCs. Using data collected from 164 western multinational companies’ subsidiary units located in China and Finland, this study aims to investigate cross-border knowledge transfer within the MNC. It explores a number of factors that influence the transfer of knowledge among units in the differentiated MNC. The study consists of five individual papers. Paper 1 investigates a range of organizational mechanisms that may positively influence a subsidiary’s propensity to undertake knowledge transfers to other parts of the corporation. Paper 2 explores the impact of subsidiary location on the motivational dispositions of knowledge receiving units to value and accept knowledge from subsidiaries located in economically less advanced countries. Paper 3 examines the influence of social capital variables on knowledge transfer in dyadic relationships between foreign-owned subsidiaries and their sister and patent units. Paper 4 provides some initial insights into potentially different effects of trust and shared vision in intra-organizational vs. inter-organizational relationships. Using a case study setting, Paper 5 explores means and mechanisms used in transferring human resource management practices to Western MNCs’ business units in China from a cultural perspective. The results of the study show that MNC management through choices regarding organizational controls can encourage and enhance corporate-internal knowledge transfer. It also finds evidence that more knowledge is transferred from subsidiaries located in an industrialized country (e.g., Finland) than subsidiaries located in a developing country (e.g., China). While the study has highlighted the importance of social capital in promoting knowledge transfer, it has also uncovered some new findings that the effect of trust and shared vision may be contingent upon different contexts. Finally, in Paper 5, a number of mechanisms used in transferring selected HRM practices and competences to the Chinese business units have been identified. The findings suggest that cultural differences should be taken into consideration in the choice and use of different transfer mechanisms.

Towards Explaining the Use of Control Mechanisms in Foreign Subsidiaries of MNCs (summary section only)

Control is central to management and there is already a considerable body of research on control. However, the emergence and growth of multinational corporations (MNCs) has renewed the interest in control, as MNCs are complex (often large) organizations that face circumstances beyond those of national business organizations. The geographical dispersion of MNC activities means that the headquarters controls subsidiaries that differ with regard to power and that are embedded in different cultural, political, legal and educational systems. Foreign subsidiary control also takes place across language boundaries and physical (i.e. geographical) distances. In face of these challenges, how are foreign subsidiaries controlled? The thesis explores different types of control mechanisms and attempts to explain the degree to which they are used to control foreign subsidiaries. It contributes to existing knowledge on control by exploring how five different control mechanisms are related to each other. Previous research has tended to focus only on one or two control mechanisms and seldom has their effect on each other been explored. The thesis also contributes by including two central aspects of the MNC that have been neglected in much of the research on foreign subsidiary control: language competence of subsidiary staff and physical distance between the headquarters and its subsidiaries. The findings indicate that specific control mechanisms should not be studied in isolation as there are intricate relationships among the different control mechanisms. Language competence of the subsidiary staff can furthermore affect the type and degree of control that the headquarters can exercise over a subsidiary. The findings also indicate that changes in the physical distance between subsidiaries and its headquarters (i.e. a relocation of the headquarters as part of a restructuring process) can have great consequences for the headquarters-subsidiary relationship.

Adaptive load control of the central processor in a distributed system with a star topology

The author presents adaptive control techniques for controlling the flow of real-time jobs from the peripheral processors (PPs) to the central processor (CP) of a distributed system with a star topology. He considers two classes of flow control mechanisms: (1) proportional control, where a certain proportion of the load offered to each PP is sent to the CP, and (2) threshold control, where there is a maximum rate at which each PP can send jobs to the CP. The problem is to obtain good algorithms for dynamically adjusting the control level at each PP in order to prevent overload of the CP, when the load offered by the PPs is unknown and varying. The author formulates the problem approximately as a standard system control problem in which the system has unknown parameters that are subject to change. Using well-known techniques (e.g., naive-feedback-controller and stochastic approximation techniques), he derives adaptive controls for the system control problem. He demonstrates the efficacy of these controls in the original problem by using the control algorithms in simulations of a queuing model of the CP and the load controls.

Experimental study and optimization of Plasma Actuators for Flow control in subsonic regime

Experimental study and optimization of Plasma Ac- tuators for Flow control in subsonic regime PRADEEP MOISE, JOSEPH MATHEW, KARTIK VENKATRAMAN, JOY THOMAS, Indian Institute of Science, FLOW CONTROL TEAM | The induced jet produced by a dielectric barrier discharge (DBD) setup is capable of preventing °ow separation on airfoils at high angles of attack. The ef-fect of various parameters on the velocity of this induced jet was studied experimentally. The glow discharge was created at atmospheric con-ditions by using a high voltage RF power supply. Flow visualization,photographic studies of the plasma, and hot-wire measurements on the induced jet were performed. The parametric investigation of the charac- teristics of the plasma show that the width of the plasma in the uniform glow discharge regime was an indication of the velocity induced. It was observed that the spanwise and streamwise overlap of the two electrodes,dielectric thickness, voltage and frequency of the applied voltage are the major parameters that govern the velocity and the extent of plasma.e®ect of the optimized con¯guration on the performance characteristics of an airfoil was studied experimentally.

An instantaneous control model for flow control in an ATM network

This paper is concerned with the optimal flow control of an ATM switching element in a broadband-integrated services digital network. We model the switching element as a stochastic fluid flow system with a finite buffer, a constant output rate server, and a Gaussian process to characterize the input, which is a heterogeneous set of traffic sources. The fluid level should be maintained between two levels namely b1 and b2 with b1control on the ATM network is considered