An evaluation of fibrous structure and physical characteristics of Cutia nut (Couepia edulis Prance) shell

The Cutia-nut (Couepia edulis Prance), a species originally from the Amazon region, has a kernel with reasonable nutritional value and a hard and thick woody shell that constitute most of the fruit. After the kernel removal, the shells are regarded as waste. The possibility of using such shells, as raw material for burning or charcoal production, as well as milled residue for structural reinforcement materials is quite feasible, considering environmental and economical aspects. There is, however, a complete lack of characterization of the Cutia-nut shell and other similar species which can aggregate desirable qualities for application as engineering material. In this study some analyses are presented aiming at providing information for potential uses of these residues. In general, the shells follow a regular shape with certain dimensional proportionality to the kernel. The shell is a fibrous material with high lignin content, present low water absorption and high resistance to natural degradation.

In situ characterization of porous VPO catalysts with fibrous structure: Identifying the redox behavior and the stability of active sites

Two VPO materials with fibrillar morphology have been prepared by the aid of electrospinning technique. One is a VPO carbon-supported material (VCF200) with fibrous morphology and very high surface area that is stable under oxidizing conditions up to 350C. The other material is a bulk mixed VPO oxide (VPO500) with fibrous structure obtained after optimizing the calcination of the carbon support in VCF200. Despite it is a bulk oxide material, this material exhibits a high surface area (> 60 m2/g). The redox behavior of both samples was monitored by in situ Raman spectroscopy under oxidation/reduction cycles. For the dehydrated supported sample (VCF200), the pyrophosphate phase (VO)2P2O7 (Raman ~930 cm-1) is detected, which has been described as the active phase (see Figure (a) below). This phase is quite stable since it does not disappear upon subsequent oxidation/reduction cycles. Under reduction conditions at 125C, in consecutive cycles, additional Raman bands appear at ~1090 cm-1 that are characteristic of the αII-VOPO4 phase. On the other hand, the bulk phases show a reversible behavior under redox cycles (Figure (b)). Under reducing conditions, a Raman band appears at ~980 cm-1 (β-VPO phase), whereas under oxidation conditions some segregation to VOx oxides occurs. Nevertheless, this segregation is reversible and the β-VPO phase forms again under reducing conditions. Thus, these results demonstrate that the active VPO phases of these fibrous catalysts are quite stable, and that their structure is reversible under several redox cycles, which make them suitable as oxidation catalysts.

Estudo da estabilidade térmica da pele

Mestrado em Engenharia Química

Rat muscle opacity decrease due to the osmosis of a simple mixture

It is known that the fibrous structure of muscle causes light scattering. This phenomenon occurs due to the refractive index discontinuities located between muscle fibers and interstitial fluid. To study the possibility of reducing light scattering inside muscle, we consider its spectral transmittance evolution during an immersion treatment with an optical clearing solution containing ethanol, glycerol, and distilled water. Our methodology consists of registering spectral transmittance of muscle samples while immersed in that solution. With the spectral data collected, we represent the transmittance evolution for some wavelengths during the treatment applied. Additionally, we study the variations that the treatment has caused on the samples regarding tissue refractive index and mass. By analyzing microscopic photographs of tissue cross section, we can also verify changes in the internal arrangement of muscle fibers caused by the immersion treatment. Due to a mathematical model that we develop, we can explain the variations observed in the studied parameters and estimate the amount of optical clearing agent that has diffused into the tissue samples during the immersion treatment. At the end of the study, we observe and explain the improvement in tissue spectral transmittance, which is approximately 65% after 20 min.

Diffusion Tensor Imaging as a Diagnostic and Research Tool: A Study on Preterm Infants

Diffusion tensor imaging (DTI) is an advanced magnetic resonance imaging (MRI) technique. DTI is based on free thermal motion (diffusion) of water molecules. The properties of diffusion can be represented using parameters such as fractional anisotropy, mean diffusivity, axial diffusivity, and radial diffusivity, which are calculated from DTI data. These parameters can be used to study the microstructure in fibrous structure such as brain white matter. The aim of this study was to investigate the reproducibility of region-of-interest (ROI) analysis and determine associations between white matter integrity and antenatal and early postnatal growth at term age using DTI. Antenatal growth was studied using both the ROI and tract-based spatial statistics (TBSS) method and postnatal growth using only the TBSS method. The infants included to this study were born below 32 gestational weeks or birth weight less than 1,501 g and imaged with a 1.5 T MRI system at term age. Total number of 132 infants met the inclusion criteria between June 2004 and December 2006. Due to exclusion criteria, a total of 76 preterm infants (ROI) and 36 preterm infants (TBSS) were accepted to this study. The ROI analysis was quite reproducible at term age. Reproducibility varied between white matter structures and diffusion parameters. Normal antenatal growth was positively associated with white matter maturation at term age. The ROI analysis showed associations only in the corpus callosum. Whereas, TBSS revealed associations in several brain white matter areas. Infants with normal antenatal growth showed more mature white matter compared to small for gestational age infants. The gestational age at birth had no significant association with white matter maturation at term age. It was observed that good early postnatal growth associated negatively with white matter maturation at term age. Growth-restricted infants seemed to have delayed brain maturation that was not fully compensated at term, despite catchup growth.

Obtenção e caracterização de fibras poliméricas e cerâmicas pela técnica de “blow-spinning”

Pós-graduação em Ciência dos Materiais - FEIS

Detecção eletroquímica de ácidos urônicos presentes no bagaço de cana-de-açúcar utilizando eletrodo modificado com nanopartículas de cobre em técnica de HPLC

Pós-graduação em Química - IQ

Determination of uronic acids in sugarcane bagasse by anion-exchange chromatography using an electrode modified with copper nanoparticles

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Otimização do método lignina brometo de acetila na determinação do teor de lignina em plantas forrageiras e comparação com os métodos lignina detergente ácido e lignina Klason

Técnicas analíticas empregadas para a quantificação do teor de lignina em plantas forrageiras, atualmente em uso, são questionáveis quanto às suas acurácias. O método lignina detergente ácido (LDA), que é um dos métodos mais utilizado em Ciência Animal e Agronomia, apresenta algumas falhas, particularmente devido à parcial solubilização da lignina durante a preparação da fibra em detergente ácido (FDA). A lignina Klason (LK), outro método muito usado, apresenta o inconveniente de mensurar a proteína da parede celular como sendo lignina. Em ambos os procedimentos recomenda-se também mensurar cinzas nos resíduos de lignina. A quantificação da concentração de lignina pelo método espectrofotométrico lignina brometo de acetila (LBA) vem ganhando interesse de pesquisadores no Brasil e no exterior. Nesta metodologia, a lignina da planta contida na preparação parede celular (PC) é solubilizada numa solução a 25% de brometo de acetila em ácido acético e a absorbância mensurada é com luz UV a 280 nm. O valor da absorbância é inserido numa equação de regressão e a concentração de lignina é obtida. Para que esta técnica analítica seja mais aceita pelos pesquisadores, ela deve ser, obviamente, convincente e atrativa. O presente trabalho analisou alguns parâmetros relacionados à LBA em 7 gramíneas e 6 leguminosas, em dois estádios de maturidade. Dentre as diferentes temperaturas de pré-secagem, os resultados indicaram que os procedimentos de 55°C com ventilação e liofilização podem ser utilizados com a mesma eficácia. As temperaturas de 55°C sem ventilação e 80°C sem ventilação não são recomendadas, pois aumentaram os valores de FDA e LDA, possivelmente devido ao surgimento de artefatos de técnica como os compostos de Maillard. No método LBA os valores menores das amostras de leguminosas chamaram a atenção e colocaram em questão se a lignina destas plantas seria menos solúvel no reagente brometo de acetila. Dentre algumas alterações na metodologia da técnica LBA, a utilização do moinho de bolas (para diminuir o tamanho particular) nas amostras de PC não mostrou efeito; a hipótese era melhorar a solubilização da lignina usando partículas menores. O uso de um ultrasonicador, que aumenta a vibração das moléculas e assim, facilitaria a solubilização da lignina no reagente brometo de acetila, melhorou a solubilização da lignina em cerca de 10%, tanto nas gramíneas como nas leguminosas. Foi acoplado um ensaio biológico como referência, a degradabilidade in vitro da matéria seca (DIVMS); e como a lignina está intimamente associada à estrutura fibrosa da parede celular, também foi feito um ensaio de degradabilidade in vitro da fibra em detergente neutro (DIVFDN). Os resultados confirmaram o efeito da maturidade, reduzindo a degradabilidade nas plantas mais maduras, e que o teor de lignina de leguminosas é realmente inferior ao de gramíneas. Os resultados de degradabilidade apresentaram coeficientes de correlação mais elevados com o método LBA, quando foi empregada a técnica do ultrasom; o método LK mostrou os menores coeficientes. Também testou-se, com sucesso, a utilização da FDN, como preparação fibrosa, ao invés de PC. A razão é simples: enquanto que a FDN é amplamente conhecida, a preparação PC não o é. Inquestionável que esta manobra facilitará substancialmente a divulgação desse método, tornando-a mais aceitável pela comunidade científica

Eutectic grains in unmodified and strontium-modified hypoeutectic aluminum-silicon alloys

Additions of strontium to hypoeutectic aluminum-silicon alloys modify the morphology of the eutectic silicon phase from a coarse platelike structure to a fine fibrous structure. Thermal analysis, interrupted solidification, and microstructural examination of sand castings in this work revealed that, in addition to a change in silicon morphology, modification with strontium also causes an increase in the size of eutectic grains. The eutectic grain size increases because fewer grains nucleate, possibly due to poisoning of the phosphorus-based nucleants, that are active in the unmodified alloy. A simple growth model is developed to estimate the interface velocity during solidification of a eutectic grain. The model confirms, independent of microstructural observations, that the addition of 100 ppm strontium increases the eutectic grain size by at least an order of magnitude compared with the equivalent unmodified alloy. The model predicts that the growth velocity varies significantly during eutectic growth. At low strontium levels, these variations may be sufficient to cause transitions between flake and fibrous silicon morphologies depending on the casting conditions. The model can be used to rationally interpret the eutectic grain structure and silicon morphology of fully solidified aluminum-silicon castings and, when coupled with reliable thermal data, can be used to estimate the eutectic grain size.

Electrospun hierarchical artificial muscle for soft robotics applications

Nowadays, one of the most ambitious challenges in soft robotics is the development of actuators capable to achieve performance comparable to skeletal muscles. Scientists have been working for decades, inspired by Nature, to mimic both their complex structure and their perfectly balanced features in terms of linear contraction, force-to-weight ratio, scalability and flexibility. The present Thesis, contextualized within the FET open Horizon 2020 project MAGNIFY, aims to develop a new family of innovative flexible actuators in the field of soft-robotics. For the realization of this actuator, a biomimetic approach has been chosen, drawing inspiration from skeletal muscle. Their hierarchical fibrous structure was mimicked employing the electrospinning technique, while the contraction of sarcomeres was designed employing chains of molecular machines, supramolecular systems capable of performing movements useful to execute specific tasks. The first part deals with the design and production of the basic unit of the artificial muscle, the artificial myofibril, consisting in a novel electrospun core-shell nanofiber, with elastomeric shell and electrically conductive core, coupled with a conductive coating, for the realization of which numerous strategies have been investigated. The second part deals instead with the integration of molecular machines (provided by the project partners) inside these artificial myofibrils, preceded by the study of several model molecules, aimed at simulating the presence of these molecular machines during the initial phases of the project. The last part concerns the realization of an electrospun multiscale hierarchical structure, aimed at reproducing the entire muscle morphology and fibrous organization. These research will be joined together in the near future like the pieces of a puzzle, recreating the artificial actuator most similar to biological muscle ever made, composed of millions of artificial myofibrils, electrically activated in which the nano-scale movement of molecular machines will be incrementally amplified to the macro-scale contraction of the artificial muscle.

The effect of solidification rate on the structure of magnesium-aluminium eutectic grains

A magnesium-aluminium alloy of eutectic composition was solidified under two different cooling conditions, producing a low and a high growth rate of the eutectic solid-liquid interface. The high growth rate specimen contained smaller eutectic grains and cells, with a smaller interphase spacing compared with the low growth rate specimen. The high growth rate specimen also contained some primary Mg17Al12 dendrites, suggesting that the coupled zone is skewed towards the Mg phase with increased undercooling, A lamellar eutectic morphology was observed in the low growth rate specimen, while the morphology was fibrous in the high growth rate specimen.

The Effects of Some Furnish and Paper Structure Related Factors on Wet Web Tensile and Relaxation Characteristics

The objective of this thesis was to identify the effects of different factors on the tension and tension relaxation of wet paper web after high-speed straining. The study was motivated by the plausible connection between wet web mechanical properties and wet web runnability on paper machines shown by previous studies. The mechanical properties of wet paper were examined using a fast tensile test rig with a strain rate of 1000%/s. Most of the tests were carried out with laboratory handsheets, but samples from a pilot paper machine were also used. The tension relaxation of paper was evaluated as the tension remaining after 0.475 s of relaxation (residual tension). The tensile and relaxation properties of wet webs were found to be strongly dependent on the quality and amount of fines. With low fines content, the tensile strength and residual tension of wet paper was mainly determined by the mechanical interactions between fibres at their contact points. As the fines strengthen the mechanical interaction in the network, the fibre properties also become important. Fibre deformations caused by the mechanical treatment of pulp were shown to reduce the mechanical properties of both dry and wet paper. However, the effect was significantly higher for wet paper. An increase of filler content from 10% to 25% greatly reduced the tensile strength of dry paper, but did not significantly impair wet web tensile strength or residual tension. Increased filler content in wet web was shown to increase the dryness of the wet web after the press section, which partly compensates for the reduction of fibrous material in the web. It is also presumable that fillers increase entanglement friction between fibres, which is beneficial for wet web strength. Different contaminants present in white water during sheet formation resulted in lowered surface tension and increased dryness after wet pressing. The addition of different contaminants reduced the tensile strength of the dry paper. The reduction of dry paper tensile strength could not be explained by the reduced surface tension, but rather on the tendency of different contaminants to interfere with the inter-fibre bonding. Additionally, wet web strength was not affected by the changes in the surface tension of white water or possible changes in the hydrophilicity of fibres caused by the addition of different contaminants. The spraying of different polymers on wet paper before wet pressing had a significant effect on both dry and wet web tensile strength, whereas wet web elastic modulus and residual tension were basically not affected. We suggest that the increase of dry and wet paper strength could be affected by the molecular level interactions between these chemicals and fibres. The most significant increases in dry and wet paper strength were achieved with a dual application of anionic and cationic polymers. Furthermore, selectively adding papermaking chemicals to different fibre fractions (as opposed to adding chemicals to the whole pulp) improved the wet web mechanical properties and the drainage of the pulp suspension.

Structure and biogenesis of the capsular F1 antigen from Yersinia pestis: Preserved folding energy drives fiber formation

Most gram-negative pathogens express fibrous adhesive virulence organelles that mediate targeting to the sites of infection. The F1 capsular antigen from the plague pathogen Yersinia pestis consists of linear fibers of a single subunit (Caf1) and serves as a prototype for nonpilus organelles assembled via the chaperone/usher pathway. Genetic data together with high-resolution X-ray structures corresponding to snapshots of the assembly process reveal the structural basis of fiber formation. Comparison of chaperone bound Caf1 subunit with the subunit in the fiber reveals a novel type of conformational change involving the entire hydrophobic core of the protein. The observed conformational change suggests that the chaperone traps a high-energy folding intermediate of Caf1. A model is proposed in which release of the subunit allows folding to be completed, driving fiber formation.

Kidney of Minke Whale (Baleanoptera acutorostrata): Architecture and structure

Sarmento C. A. P., Ferreira A. O., Rodrigues E. A. F., Lesnau G. G., Rici R. E. G., Abreu D. K., Biasi C. & Miglino M. A. 2012. [Kidney of Minke Whale (Baleanoptera acutorostrata): Architecture and structure.] Rins de Baleia Minke (Baleanoptera acutorostrata): arquitetura e estrutura. Pesquisa Veterinaria Brasileira 32(8): 807-811. Departamento de Cirurgia, Setor de Anatomia dos Animais Domesticos e Silvestres, Universidade de Sao Paulo, Av. Prof. Dr. Orlando Marques de Paiva 87, Sao Paulo, SP 05508-270, Brazil. E-mail: sarmento@usp.br Among marine mammals, whale is one of the most attention-arousing animals, especially concerning its urinary tract. This system follows the pattern of mammals with regard to its constitution, however, it differs in renal morphology and number of lobes, which, in turn, form complete reniculi, agglutinated in hundreds. This structure is supported by fibrous connective tissue, but highly capable of maintaining electrolyte balance. Six pairs of kidneys of Minke whale (Balaenoptera acutorostrata), collected in 1982, in Cabedelo, Paraiba, Brazil, in the last fishing allowed, were dissected. These kidneys were preserved in 10% formaldehyde and they presented a very large histologic layer of collagen surrounding the medullary wall. The urinary collecting duct form papillary glasses, that reach a single collecting center which discharges in the ureter. It was found that the kidney of Minke whale has a lobe characteristic, with, on average, 700 reniculi; each reniculus has anatomical and functional characteristics of a unipyramidal kidney, with an inner layer (medulla), and an outer layer (cortex), and independent irrigation, with formation of individually arcuate arteries, as observed in unipyramidal terrestrial mammals. However, the set gathering all these reniculi constitutes, in the end, a multilobular and polipyramidal kidney, contrary to the morphology of most terrestrial mammals. It was not possible to distinguish the renicular cortex structures of the Minke whale in the level of light microscopy. Through scanning electron microscopy, it was possible to visualize a cortical layer located between two fibrous capsules. This joint, in turn, consists of connective tissue, which, along with a layer of collagen and elastic fibers, separates the cortex from the medulla; the kidney glomeruli were visualized, completely taken by the glomerular vessels and arranged into several layers. One notices that the glomerular cavity is almost a virtual space into which the glomerular filtrate is drained, and it does not present a globular shape. Vascularization is increased in the medullary region. The difference between the kidneys of terrestrial and marine mammals consists in the arrangement of morphological components, favoring the organ's physiology.