Relationships between skin follicle characteristics and fibre properties of Suri and Huacaya alpacas and Peppin Merino sheep

We aimed to quantify the number, type and arrangement of skin follicles in Huacaya and Suri alpaca skin and correlate their follicle characteristics with fibre traits of harvested fibre and compared these relationships with those of Merino sheep. Fibre and skin samples were collected from the mid-side of 12 Huacaya alpacas, 24 Suri alpacas and 10 Merino sheep. The mean fibre diameter (MFD ± s.e.) of the Huacaya and Suri were: 35.5 ± 0.9 and 28.3 ± 1.0 μm, respectively. The follicle groups found for alpacas were very different from the normal trio of primary follicles found in sheep and goats. The follicle group of the alpacas consisted of a single primary follicle surrounded by a variable number of secondary follicles. The mean ± s.e. primary follicle density was 3.1 ± 0.3 and 2.7 ± 0.1 follicles/mm² for Huacaya and Suri, respectively. The mean ± s.e. secondary follicle density (SFD) was 13.7 ± 1.2 and 17.5 ± 0.6 follicles/mm² for Huacaya and Suri, respectively. The mean ± s.e. ratio of secondary to primary follicles (S/P ratio) was 5.1 ± 0.5 for the Huacaya and 7.3 ± 0.2 for the Suri alpacas. The sheep had higher S/P ratios and SFD, lower MFD and produced significantly heavier fleeces. The key correlations found between traits in alpacas include a negative correlation between SFD and MFD (r = –0.71, P = 0.001) and a negative correlation between S/P ratio and MFD (r = –0.44, P = 0.003) and a positive correlation between S/P ratio and total follicle density (r = 0.38, P = 0.010). The study revealed that important relationships exist between alpaca skin follicle characteristics and fibre characteristics. It was the number of secondary follicles in a group that imparts density and a corresponding reduced MFD.

Fibre properties affecting the softness of wool and other keratins

The emerging market for next-to-skin knitwear requires wool to satisfy the consumer’s tactile requirements for softness. The role of the fibre’s surface and physical properties on fibre and fabric softness was examined. The fibre’s cuticle properties were found to have a greater influence on softness than the fibre’s mechanical properties.

Measuring the influence of fibre-to-fabric properties on the pilling of wool fabrics

This study ranks the contribution of various fibre, yarn and fabric attributes to the pilling of wool knitwear. On the basis of an artificial neural network modelling, a combination of sensitivity analysis, forwards/backwards search and genetic algorithms was used to identify the importance of various fibre/yarn/fabric input parameters. The three different techniques show broad similarities in their assessment of which input parameters are important or are not important in affecting fabric pilling. The ranking shows that fabric cover factor has the most effect on pilling, followed by yarn count and thin places, fibre length, yarn twist, etc. It is further illustrated that the directional trend of the predicted pilling outputs for a selection of inputs was in line with the expected behaviour. To verify the findings of input feature selection, input factors deemed to have a small effect on the predicted pilling output, such as fibre length and diameter variations and curvature, were removed and the subsequent performance statistically compared to the original multi-layer perceptron. Differences between the outputs predicted by the original and pruned models are found not to be statistically significant at the 5% significance level. Results from this study may help manufacturers and knitwear designers in choosing the most appropriate materials and structures to reduce the pilling propensity of wool knitwear.

Parametric Analysis of Effective Material Properties of Thickness-Shear Piezoelectric Macro-Fibre Composites

A previous study on the characterization of effective material properties of a d(15) thickness-shear piezoelectric Macro-Fibre Composite (MFC) made of seven layers (Kapton, Acrylic, Electrode, Piezoceramic Fibre and Epoxy Composite, Electrode, Acrylic, Kapton) using a finite element homogenization method has shown that the packaging reduces significantly the shear stiffness of the piezoceramic material and, thus, leads to significantly smaller effective electromechanical coupling coefficient k(15) and piezoelectric stress constant e(15) when compared to the piezoceramic fibre properties. Therefore, the main objective of this work is to perform a parametric analysis in which the effect of the variations of fibre volume fraction, Epoxy elastic modulus, electrode thickness and active layer thickness on the MFC effective material properties is evaluated. Results indicate that an effective d(15) MFC should use relatively thick fibres having relatively high shear modulus and relatively stiff epoxy filler. On the other hand, the electrode thickness does not affect significantly the MFC performance.

Parametric analysis of effective material properties of thickness-shear piezoelectric macro-fibre composites

A previous study on the characterization of effective material properties of a d15 thickness-shear piezoelectric Macro-Fibre Composite (MFC) made of seven layers (Kapton, Acrylic, Electrode, Piezoceramic Fibre and Epoxy Composite, Electrode, Acrylic, Kapton) using a finite element homogenization method has shown that the packaging reduces significantly the shear stiffness of the piezoceramic material and, thus, leads to significantly smaller effective electromechanical coupling coefficient k15 and piezoelectric stress constant e15 when compared to the piezoceramic fibre properties. Therefore, the main objective of this work is to perform a parametric analysis in which the effect of the variations of fibre volume fraction, Epoxy elastic modulus, electrode thickness and active layer thickness on the MFC effective material properties is evaluated. Results indicate that an effective d15 MFC should use relatively thick fibres having relatively high shear modulus and relatively stiff epoxy filler. On the other hand, the electrode thickness does not affect significantly the MFC performance.

Eri silk fibre attributes and sliver preparation

Eri silk produced by Philosamia cynthia ricini silkworm is a fibre not well-known to the silk industry, in spite of the fact that Eri silk is finer, softer, and has better mechanical and thermal properties than most animal fibres. Eri silk has a high commercial potential, as the host plants of Eri silk worms are widespread in diverse geographical locations, and the worms also have a higher degree of disease resistance than most other silk worms. Mills are often not aware of the properties of Eri for designing appropriate end products. Thus, Eri silk yarn is traditionally produced by hand spinning, and Eri silk usually ends up as material for handwoven shawls. The potential for bulk fibre processing and the development of soft luxurious novel Eri silk products is yet to be discovered. To better understand the material and its processing behaviour, Eri silk was characterised and cocoons were processed into tops through degumming, opening, and cutting filaments into different lengths, followed by a worsted spun silk processing route. Fibre properties such as fineness, crimp, strength and length at different processing stages up to combed tops were measured. The results indicate that staple Eri silk can be processed via the worsted topmaking route, using a cut length of 200 mm or 150 mm for filament sheets prepared from degummed cocoons.

Fibre-based devices for next generation photonics communication systems

The future broadband information network will undoubtedly integrate the mobility and flexibility of wireless access systems with the huge bandwidth capacity of photonics solutions to enable a communication system capable of handling the anticipated demand for interactive services. Towards wide coverage and low cost implementations of such broadband wireless photonics communication networks, various aspects of the enabling technologies are continuingly generating intense research interest. Among the core technologies, the optical generation and distribution of radio frequency signals over fibres, and the fibre optic signal processing of optical and radio frequency signals, have been the subjects for study in this thesis. Based on the intrinsic properties of single-mode optical fibres, and in conjunction with the concepts of optical fibre delay line filters and fibre Bragg gratings, a number of novel fibre-based devices, potentially suitable for applications in the future wireless photonics communication systems, have been realised. Special single-mode fibres, namely, the high birefringence (Hi-Bi) fibre and the Er/Yb doped fibre have been employed so as to exploit their merits to achieve practical and cost-effective all-fibre architectures. A number of fibre-based complex signal processors for optical and radio frequencies using novel Hi-Bi fibre delay line filter architectures have been illustrated. In particular, operations such as multichannel flattop bandpass filtering, simultaneous complementary outputs and bidirectional nonreciprocal wavelength interleaving, have been demonstrated. The proposed configurations featured greatly reduced environmental sensitivity typical of coherent fibre delay line filter schemes, reconfigurable transfer functions, negligible chromatic dispersions, and ease of implementation, not easily achievable based on other techniques. A number of unique fibre grating devices for signal filtering and fibre laser applications have been realised. The concept of the superimposed fibre Bragg gratings has been extended to non-uniform grating structures and into Hi-Bi fibres to achieve highly useful grating devices such as overwritten phase-shifted fibre grating structure and widely/narrowly spaced polarization-discriminating filters that are not limited by the intrinsic fibre properties. In terms of the-fibre-based optical millimetre wave transmitters, unique approaches based on fibre laser configurations have been proposed and demonstrated. The ability of the dual-mode distributed feedback (DFB) fibre lasers to generate high spectral purity, narrow linewidth heterodyne signals without complex feedback mechanisms has been illustrated. A novel co-located dual DFB fibre laser configuration, based on the proposed superimposed phase-shifted fibre grating structure, has been further realised with highly desired operation characteristics without the need for costly high frequency synthesizers and complex feedback controls. Lastly, a novel cavity mode condition monitoring and optimisation scheme for short length, linear-cavity fibre lasers has been proposed and achieved. Based on the concept and simplicity of the superimposed fibre laser cavities structure, in conjunction with feedback controls, enhanced output performances from the fibre lasers have been achieved. The importance of such cavity mode assessment and feedback control for optimised fibre laser output performance has been illustrated.

Recovery of glass fibre and carbon fibres from reinforced thermosets by batch pyrolysis and investigation of fibre re-using as reinforcement in LDPE matrix

A semi-batch pyrolysis process was used to recover samples carbon fibre and glass fibre from their respective wastes. The mechanical properties of the recovered fibres were tested and compared to those of virgin fibres, showing good retention of the fibre properties. The recovered fibres were then used to prepare new LDPE composite materials with commercial and laboratory-synthesized compatibilizers. Mild oxidation of the post-pyrolysis recovered fibres and the use of different compatibilizers gave significant improvements in the mechanical properties of the LDPE composites; however some of the manufactured composites made from recovered fibres had properties similar to those made from virgin fibres.

Addressing factory needs in cane variety selection

Cane fibre content has increased over the past ten years. Some of that increase can be attributed to new varieties selected for release. This paper reviews the existing methods for quantifying the fibre characteristics of a variety, including fibre content and fibre quality measurements – shear strength, impact resistance and short fibre content. The variety selection process is presented and it is reported that fibre content has zero weighting in the current selection index. An updated variety selection approach is proposed, potentially replacing the existing selection process relating to fibre. This alternative approach involves the use of a more complex mill area level model that accounts for harvesting, transport and processing equipment, taking into account capacity, efficiency and operational impacts, along with the end use for the bagasse. The approach will ultimately determine a net economic value for the variety. The methodology lends itself to a determination of the fibre properties that have a significant impact on the economic value so that variety tests can better target the critical properties. A low-pressure compression test is proposed as a good test to provide an assessment of the impact of a variety on milling capacity. NIR methodology is proposed as a technology to lead to a more rapid assessment of fibre properties, and hence the opportunity to more comprehensively test for fibre impacts at an earlier stage of variety development.

The soft impact of composite sandwich beams with a square-honeycomb core

The dynamic response of end-clamped monolithic beams and sandwich beams of equal areal mass have been measured by loading the beams at mid-span with metal foam projectiles to simulate localised blast loading. The sandwich beams were made from carbon fibre laminate and comprised identical face sheets and a square-honeycomb core. The transient deflection of the beams was determined as a function of projectile momentum, and the measured response was compared with finite element simulations based upon a damage mechanics approach. A range of failure modes were observed in the sandwich beams including core fracture, plug-type shear failure of the core, debonding of the face sheets from the core and tensile tearing of the face sheets at the supports. In contrast, the monolithic beams failed by a combination of delamination of the plies and tensile failure at the supports. The finite element simulations of the beam response were accurate provided the carbon fibre properties were endowed with rate sensitivity of damage growth. The relative performance of monolithic and sandwich beams were quantified by the maximum transverse deflection at mid-span for a given projectile momentum. It was found that the sandwich beams outperformed both monolithic composite beams and steel sandwich beams with a square-honeycomb core. However, the composite beams failed catastrophically at a lower projectile impulse than the steel beams due to the lower ductility of the composite material. © 2011 Elsevier Ltd. All rights reserved.

Improvement of the efficiency of energy transfer in the hydro-entanglement process

Hydro-entanglement is a versatile process for bonding non-woven fabrics by the use of fine, closely-spaced, high-velocity jets of water to rearrange and entangle arrays of fibres. The cost of the process mainly depends on the amount of energy consumed. Therefore, the economy of the process is highly affected by optimisation of the energy required. In this paper a parameter called critical pressure is introduced which is indicative of the energy level requirement. The results of extensive experimental work are reported and analysed to give a clear understanding of the effect of the web and fibre properties on the critical pressure in the hydro-entanglement process. Furthermore, different energy-transfer distribution schemes are tested on various fabrics. The optimum scheme which involves the lowest energy consumption and the best fabric properties is identified. © 2001 Published by Elsevier Science Ltd. All rights reserved.

Cuticle modifications and dyeing property of ultrasonically scoured wool

Ultrasonics has the potential to reduce the cost and environmental impact of textile processing. This work investigates the effects of utrasonic irradiation during wool scouring on fibre surface properties and fibre dyeing rate. A range of ultrasonic frequencies were used in the scouring bath to examine the forms of fibre cuticle damage. It was shown that ultrasonically scoured wool underwent some modifications of the fibre surface structure which resulted in a higher rate of dye uptake by the fibres, when compared with the conventionally scoured wool. The lower the ultrasonic frequency the more sever was the cuticle damage to wool during scouring, hence the higher the fibre dye uptake.

Frequency dependence of ultrasonic wool scouring

Conventional aqueous scouring of greasy wool promotes wool felting and can be energy and water intensive. Ultrasonic wool scouring could be an alternative technology to minimise the negative impact, provided that the cleaning efficiency and fibre quality are not compromised. This study  examined the influence of ultrasonic irradiation frequency and ultrasonic power variations on wool scouring performance at different liquor ratios. Scoured fibre, residual ash content, residual grease content, whiteness and yellowness were evaluated. The impact of liquor degassing on wool scouring effectiveness was studied. Fibre surface damage was also assessed in this work. It was observed that while there was no significant influence of ultrasonic frequency on the whiteness or yellowness of the scoured fibres, wool scoured at frequencies of 28 kHz and 80 kHz had more grease and dirt removed than that scoured at 45 kHz. Low ultrasonic power and degassed bath liquor increased wool grease removal ability. Ultrasonic treatment caused scale cracking/peeling in some wool fibres. More severe cuticle damage was observed in fibres scoured at the lower frequency. This damage resulted in increased dye uptake by the fibres.