The combined tensile and torsional behavior of irregular fibers

Most fibers are irregular, and they are often subjected to combined loading conditions during processing and end-use. In this paper, polyester and wool fibers under the combined tensile and torsional loads have been studied for the first time, using the finite element method (FEM). The dimensional irregularities of these fibers are simulated with sine waves of different magnitude and frequency. The breaking load and breaking extension of the fibers at different twist or torsion levels are then calculated from the finite element model. The results indicate that twist and level of fiber irregularity have a major impact on the mechanical properties of the fiber and the effect of the frequency of irregularity is relatively small.

Modeling the tensile behavior of fibers with geometrical and structural irregularities

Virtually all fibers exhibit some dimensional and structural irregularities. These include the conventional textile fibers, the high-performance brittle fibers and even the newly developed nano-fibers. In recent years, we have systematically examined the effect of fiber dimensional irregularities on the mechanical behavior of the irregular fibers. This paper extends our research to include the combined effect of dimensional and structural irregularities, using the finite element method (FEM). The dimensional irregularities are represented by sine waves with a 30 % magnitude of diameter variation while the structural irregularities are represented by longitudinal and horizontal cavities distributed within the fiber structure. The results indicate that fiber geometrical or dimensional variations have a marked influence on the tensile properties of the fiber. It affects not only the values of the breaking load and extension, but also the shape of the load-extension curves. The fiber structural irregularities simulated in this study appear to have little effect on the shape of the load-extension curves.

Numerical modeling of the dynamic tensile behavior of irregular fibers

Most fibers are irregular, and they are often subjected to rapid straining during mechanical processing and end-use applications. In this paper, the effect of fiber dimensional irregularities on the dynamic tensile behavior of irregular fibers is examined, using the finite element method (FEM). Fiber dimensional irregularities are simulated with sine waves of different magnitude (10%, 30% and 50% level of diameter variation). The tensile behavior of irregular fibers is examined at different strain rates (333%/sec, 3,333%/sec and 30,000%/sec). The breaking load and breaking extension of irregular fibers at different strain rates are then calculated from the finite element model. The results indicate that strain rate has a significant effect on the dynamic tensile behavior of an irregular fiber, and that the position of the thinnest segment along the fiber affects the simulation results markedly. Under dynamic conditions, an irregular fiber does not necessarily break at the thinnest segment, which is different from the quasi-static results.

Modeling the tensile behavior of fiber bundles with irregular constituent fibers

In this paper, the effect of fiber dimensional irregularities on the tensile behavior of fiber bundles is modeled, using the finite element method (FEM). Fiber dimensional irregularities are simulated with sine waves of different magnitude. The specific stress-strain curves of fiber bundles and the constituent single fibers are obtained and compared. The results indicate that fiber diameter irregularity along fiber length has a significant effect on the tensile behavior of the fiber bundle. For a bundle of uniform fibers of different diameters, all constituent fibers will break simultaneously regardless of the fiber diameter. Similarly, if fibers within a bundle have the same pattern and level of diameter irregularity along fiber length, the fibers will break at the same time also regardless of the difference in average diameter of each fiber. In these cases, the specific stress and strain curve for the bundle overlaps with that of the constituent fibers. When the fiber bundle consists of single fibers with different levels of diameter irregularity, the specific stress-strain and load-elongation curves of the fiber bundle exhibit a stepped or “ladder” shape. The fiber with the highest irregularity breaks first, even when the thinnest section of the fiber is still coarser than the diameter of a very thin but uniform fiber in the bundle. This study suggests that fiber diameter irregularity along fiber length is a more important factor than the fiber diameter itself in determining the tensile behavior of a fiber bundle consisting of irregular fibers.

The limiting irregularity of single wool fibers

Fiber irregularity affects fiber mechanical properties. This study has, for the first time, introduced the concept of limiting irregularity to single wool fibers. The limiting irregularity is the minimum variation in fiber cross sectional area that can be expected of a single wool fiber, assuming a random length-wise distribution of its constituent cortical cells. Cortical cells were extracted from merino wool fibers and their dimensions were measured from SEM images to calculate their cross sectional area variations both between cortical cells and within cortical cells, and to work out the average number of cortical cells in the cross section of wool fibers of a given diameter. Single wool fibers were also measured at 5 µm interval along length for fiber diameter variations. These variations were found to be larger than that based on fiber limiting irregularity.

Mechanical behaviour of irregular fibre materials

This work investigates the effect of fibre irregularities on the mechanical behaviour of the irregular fibres using the finite element method (FEM). The first part of this work examines that the effect of fibre dimensional irregularities on the linear and non-linear tensile behaviour of the fibres, using a two-dimensional (2D) finite element models. In the linear simulation, a concept of method Young’s modulus is introduced. The method Young’s modulus, breaking load and breaking extension are affected by the magnitude and frequency of diameter variation in the fibre specimen. Fibre dimensional variation and the gauge length effect are also simulated. In the non-linear analysis, some additional information is obtained on changes in the yield and post-yield regions, which are clearly shown in the load-extension curves. Further investigation is focused on the flexural buckling behaviour of fibres with dimensional irregularities. A three-dimensional (3D) finite element model is used to simulate the buckling deformation of dimensionally irregular fibres, and the critical buckling load of the simulated fibre is calculated. Two parameters, the effective length and the average diameter within the effective length of an irregular fibre, are considered to be the key factors that influence the buckling behaviour of the fibre. An important aspect of this work is the calculation of the effective length of an irregular fibre specimen during buckling. This method has not been reported before. The third part of this work is on the combined tensile and torsional behaviour of fibres with dimensional irregularities, using a three-dimensional (3D) finite element model. Two types of fibres, polyester and wool, are simulated with sine waves of different level (magnitude) and frequency at different twist levels. For the polyester fibre, experiment verification of the simulation results has been carried out, and the results indicate the FE model is well acceptable for the simulation. The final part of this work examines the combined effect of dimensional and structural irregularities on the fibre tensile behaviour. Three-dimensional (3D) finite element models are used to simulate the cracks (transverse, longitudinal, combined transverse and longitudinal cracks) and cavities distributed in uniform fibres and fibres with 30% level of diameter variation, respectively. One of important conclusions is that under the simulated conditions, the dimensional irregularity of fibre influences the tensile behaviour of fibres more than the fibre structural irregularity. The fibre dimensional irregularity affects not only the values of the breaking load and breaking extension, but also the shape of load-extension curves. However, the fibre structural irregularity simulated in the study appears to have little effect on the shape of the load-extension curves. In addition, the effect of crack or cavity size, type and distribution on fibre tensile properties is also investigated.

Decision support in using fibre reinforced polymer (FRP) composites in rehabilitation of concrete bridge structures

This paper compares and reviews the recommendations and contents of the guide for the design and construction of externally bonded FRP systems for strengthening concrete structures reported by ACI committee 440 and technical report of Externally bonded FRP reinforcement for RC structures (FIB 14) in application of carbon fiber reinforced polymer (CFRP) composites in strengthening of an aging reinforced concrete headstock. The paper also discusses the background, limitations, strengthening for flexure and shear, and other related issues in use of FRP for strengthening of a typical reinforced concrete headstock structure such as durability, de-bonding, strengthening limits, fire and environmental conditions. A case study of strengthening of a bridge headstock using FRP composites is presented as a worked example in order to illustrate and compare the differences between these two design guidelines when used in conjunction with the philosophy of the Austroads (1992) bridge design code.

Corneal confocal microscopy : a novel means to detect nerve fibre damage in idiopathic small fibre neuropathy

Patients with idiopathic small fibre neuropathy (ISFN) have been shown to have significant intraepidermal nerve fibre loss and an increased prevalence of impaired glucose tolerance (IGT). It has been suggested that the dysglycemia of IGT and additional metabolic risk factors may contribute to small nerve fibre damage in these patients. Twenty-five patients with ISFN and 12 aged-matched control subjects underwent a detailed evaluation of neuropathic symptoms, neurological deficits (Neuropathy deficit score (NDS); Nerve Conduction Studies (NCS); Quantitative Sensory Testing (QST) and Corneal Confocal Microscopy (CCM)) to quantify small nerve fibre pathology. Eight (32%) patients had IGT. Whilst all patients with ISFN had significant neuropathic symptoms, NDS, NCS and QST except for warm thresholds were normal. Corneal sensitivity was reduced and CCM demonstrated a significant reduction in corneal nerve fibre density (NFD) (Pb0.0001), nerve branch density (NBD) (Pb0.0001), nerve fibre length (NFL) (Pb0.0001) and an increase in nerve fibre tortuosity (NFT) (Pb0.0001). However these parameters did not differ between ISFN patients with and without IGT, nor did they correlate with BMI, lipids and blood pressure. Corneal confocal microscopy provides a sensitive non-invasive means to detect small nerve fibre damage in patients with ISFN and metabolic abnormalities do not relate to nerve damage.

An investigation of rail condition monitoring by Fibre Bragg Grating sensors

Condition monitoring on rails and train wheels is vitally important to the railway asset management and the rail-wheel interactions provide the crucial information of the health state of both rails and wheels. Continuous and remote monitoring is always a preference for operators. With a new generation of strain sensing devices in Fibre Bragg Grating (FBG) sensors, this study explores the possibility of continuous monitoring of the health state of the rails; and investigates the required signal processing techniques and their limitations.