Electrocoagulation as a pre-treatment stage to reverse osmosis units

Reverse osmosis (RO) is used by coal seam gas (CSG) operators to treat produced water as it is a well-established and proven technology worldwide. Despite the suitability of RO, there are problems associated with RO technology such as membrane fouling which although not preventing use of RO does decrease effectiveness and increase operating costs. Hence, effective pre-treatment of water samples is essential. Electrocoagulation (EC) potentially can provide improved water purification compared to conventional coagulation prior to an RO unit. This paper provides the first reported study of EC for CSG water pre-treatment and compares the performance to a range of aluminium and iron based coagulants. It was found that EC was superior in terms of removal of silica, calcium, magnesium, barium and strontium in the produced water.

Evaluation of electrocoagulation for the pre-treatment of coal seam water

This work explored the applicability of electrocoagulation (EC) using aluminium electrodes for the removal of contaminants which can scale and foul reverse osmosis membranes from a coal seam (CS) water sample, predominantly comprising sodium chloride, and sodium bicarbonate. In general, the removal efficiency of species responsible for scaling and fouling was enhanced by increasing the applied current density/voltage and contact times (30–60 s) in the EC chamber. High removal efficiencies of species potentially responsible for scale formation in reverse osmosis units such as calcium (100%), magnesium (87.9%), strontium (99.3%), barium (100%) and silicates (98.3%) were achieved. Boron was more difficult to eliminate (13.3%) and this was postulated to be due to the elevated solution pH. Similarly, fluoride removal from solution (44%) was also inhibited by the presence of hydroxide ions in the pH range 9–10. Analysis of produced flocs suggested the dominant presence of relatively amorphous boehmite (AlOOH), albeit the formation of Al(OH)3 was not ruled out as the drying process employed may have converted aluminium hydroxide to aluminium oxyhydroxide species. Evidence for adsorption of contaminants on floc surface sites was determined from FTIR studies. The quantity of aluminium released during the electrocoagulation process was higher than the Faradaic amount which suggested that the high salt concentrations in the coal seam water had chemically reacted with the aluminium electrodes.

Treatment of Acral Persistent Papular Mucinosis with Electrocoagulation

Background: Acral persistent papular mucinosis is a rare localized form of lichen myxedematosus with few case reports and no documented therapeutic options.Objective: To report full resolution of acral persistent papular mucinosis after electrocoagulation.Methods: Case report of a 51-year-old white female diagnosed with an acral persistent papular mucinosis. The clinical and histopathologic features, treatment provided, and response to treatment are detailed.Results: Acral persistent papular mucinosis presented as multiple asymptomatic normochromic papules on the wrists. Treatment with topical and intralesional steroids was unsatisfactory. Gentle electrocoagulation led to complete resolution of the lesions and negligible scarring. The favorable results remained for 6 months of follow-up, and no new lesions have emerged.Conclusion: Our case of acral persistent papular mucinosis was successfully treated with electrocoagulation and long-lasting, excellent cosmetic results.

Electrocoagulation/flotation followed by fluidized bed anaerobic reactor applied to tannery effluent treatment

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Strategies for the management and treatment of coal seam gas associated water

Coal seam gas (CSG) is a growing industry in Queensland and represents a potential major employer and deliverer of financial prosperity for years to come. CSG is a natural gas composed primarily of methane and is found trapped underground in coal beds. During the gas extraction process, significant volumes of associated water are also produced. This associated water could be a valuable resource, however, the associated water comprises of various salt constituents that make it problematic for beneficial use. Consequently, there is a need to implement various water treatment strategies to purify the associated water to comply with Queensland’s strict guidelines and to mitigate environmental risks. The resultant brine is also of importance as ultimately it also has to be dealt with in an economical manner. In some ways it can be considered that the CSG industry does not face a water problem, as this has inherent value to society, but rather has a “salt issue” to solve. This study analyzes the options involved in both the water treatment and salt recovery processes. A brief overview of the constituents present in Queensland CS water is made to illustrate the challenges involved and a range of treatment technologies discussed. Water treatment technologies examined include clarification (ballasted flocculation, dissolved air flotation, electrocoagulation), membrane filtration (ultrafiltration), ion exchange softening and desalination (ion exchange, reverse osmosis desalination and capacitance deionization). In terms of brine management we highlighted reinjection, brine concentration ponds, membrane techniques (membrane distillation, forward osmosis), thermal methods, electrodialysis, electrodialysis reversal, bipolar membrane electrodialysis, wind assisted intensive evaporation, membrane crystallization, eutectic freeze crystallization and vapor compression. As an entirety this investigation is designed to be an important tool in developing CS water treatment management strategies for effective management in Queensland and worldwide.

Avaliação do processo de tratamento de chorume do aterro sanitário de Jardim Gramacho utilizando a técnica de Eletro-Fenton

Este trabalho compara a utilização do tratamento eletrolítico e do tratamento Eletro-Fenton, em corrente alternada (CA), no chorume proveniente do aterro de Gramacho, no estado do Rio de Janeiro. O tratamento eletrolítico consiste em utilizar eletrodos de Fe em contato com a eletricidade, que em pH adequado, sofrem dissolução formando o agente coagulante in situ. O tratamento Eletro-Fenton consiste na geração de um dos componentes do reagente de Fenton pelo método eletrolítico. Nesse trabalho o reagente de Fenton é formado pelos íons ferro gerados pelo tratamento eletrolítico unindo-se ao peróxido de hidrogênio 30% adicionado exteriormente. Amostras do chorume foram caracterizadas pelos parâmetros pH, condutividade, salinidade, temperatura, turbidez, sólidos totais dissolvidos (STD) e Demanda Química de Oxigênio (DQO). O uso do tratamento eletrolítico só mostrou resultados de remoção para DQO e cor. Para garantir um melhor desempenho na remoção de DQO e cor e encontrar valores de remoção para a turbidez foi necessário o uso do tratamento Eletro-Fenton. Alguns parâmetros são importantes no uso dessa técnica, tais como pH, dosagem de peróxido, intensidade de corrente e tempo reacional. Os resultados obtidos para a remoção de DQO, cor e turbidez, foram respectivamente, 74%, 95% e 95%, nas condições operacionais: pH 4, dosagem de 5 mL de peróxido de hidrogênio a 30 %, intensidade de corrente de 2A e tempo reacional de 30 minutos. O tratamento Eletro-Fenton se mostrou mais favorável, pois o tratamento eletrolítico nas mesmas condições operacionais, só apresentou resultado de remoção de DQO que foi de 56%, mesmo sendo o consumo energético idêntico para ambos os processos (0,6 k W h m-3)

Emprego dos processos de eletrofloculação e osmose inversa no tratamento de águas oleosas

A descarga desenfreada de águas residuais no meio ambiente, ao longo dos últimos anos, vem acelerando o processo de contaminação e degradação dos corpos hídricos no mundo. Tais rejeitos apresentam elevada carga de contaminantes e de concentração de matéria orgânica o que leva a mortandade das espécies pela concorrência ao oxigênio e, em casos extremos, a aceleração dos processos de eutrofização. Pensando nisso, o presente trabalho estudou um sistema híbrido, em batelada, de tratamento de águas oleosas simuladas em laboratório pela adição de um determinado óleo lubrificante em uma solução aquosa de agentes emulsificantes e eletrólito suporte. O sistema de tratamento foi composto de duas etapas, onde na primeira avaliou-se o uso da técnica da eletrofloculação, responsável por quebrar a estabilidade das emulsões óleo/água e de uma segunda que avaliou o uso de processos de separação com membranas visando à remoção do metal adicionado ao efluente na etapa anterior. O sistema de eletrofloculação foi avaliado em relação ao uso de eletrodos de alumínio e ferro com correntes elétricas de 1A, 2A e 3A, nos modos contínuo e alternado. Os resultados apontaram um maior consumo evidente de massa de eletrodos quando do uso da corrente contínua, 4,0337g 0,0132 para o alumínio e 3,8260g 0,0181 para o ferro ao passo que o consumo foi de 2,1400g 0,0099 para o alumínio e 2,4121g 0,0127 para o ferro quando do o uso da corrente alternada. Foram alcançadas remoções máximas de 98 % 0 da DQO, 99,77 % 0,27 de remoção da cor e 100 % 0 de remoção da turbidez para o uso de corrente alternada e eletrodos de alumínio enquanto se alcançaram remoções máximas 96 % 1 da DQO, 99,46 % 0,82 de remoção da cor e também 100 % 0 de remoção da turbidez no uso de eletrodos de ferro. Na segunda etapa do estudo, a osmose inversa, o sistema utilizado atingiu rejeições de 99,53 % 0,12; 99,56 % 0,13 e de 98,87 % 0,36, para pressões respectivas de 10, 20 e 30 bar. Além disso, foram obtidos fluxos crescentes de permeado 10,87 L/h.m2 0,25; 15,67 L/h.m2 0,53; 18,49 L/h.m2 0,74 com o também aumento da pressão. Ao final do estudo alcançou-se um efluente final com baixa carga orgânica e de metais, estando o mesmo apto ao lançamento nos corpos receptores. Entretanto, mecanismos de controle, sobretudo de pH devem ser incluídos no projeto desses sistemas uma vez que esse parâmetro sofre alterações ao longo do processo

Estudo dos processos eletroquímicos: eletrooxidação e eletrocoagulação

O tratamento físico-químico de águas residuais, de origem industrial, mais comum é o tratamento baseado na adição de coagulante e floculante a um efluente. No entanto, o tratamento eletroquímico é um tipo de tratamento que tem vindo a ser explorado e estudado com mais ênfase ao longo dos últimos anos. O tratamento eletroquímico é uma tecnologia AOP (Processos de Oxidação Avançada) e divide-se em eletrólise direta (oxidação e redução) e indireta (eletrocoagulação-flotação e eletrooxidação). A eletrocoagulação e eletrooxidação divergem apenas pelo tipo de reações que ocorrem, devido ao material que constitui os elétrodos. São processos complexos com uma multiplicidade de mecanismos que operam sinergicamente para remover poluentes da água. Tendo em conta a sua complexidade e ainda dificuldade de compreensão, existem na literatura diferentes versões acerca de quais os mecanismos chave, assim como diversas configurações geométricas de reatores e elétrodos. Atualmente, este tipo de tratamento tem vindo a evoluir, tornando-se num método economicamente viável para o tratamento de uma grande variedade de águas residuais, nomeadamente, aquelas que possuem compostos recalcitrantes na sua composição. O presente trabalho foi realizado nas instalações da VentilAQUA S.A. e, tendo em conta a sua área de especialidade, o trabalho exposto focou-se no desenvolvimento de soluções técnicas de AOP, nomeadamente na área eletroquímica (eletrocoagulação e eletrooxidação),para estudo dos parâmetros operacionais numa nova configuração geométrica para os elétrodos. Tendo por base os contributos da revisão bibliográfica, o estudo incidiu num reator tubular, com elétrodos de inox dispostos de forma concêntrica, à mesma distância entre si. Com este reator foram executados variados testes, com diferentes efluentes, que permitiram obter resultados operacionais de otimização de funcionamento, tendo em vista a remoção de poluentes. O estudo financeiro associado permitiu concluir que a eletrooxidação é significativamente mais económica que o tratamento físico-químico, nas condições operacionais e para os efluentes tratados. Relativamente ao Acompanhamento e Gestão de ETAR’s (Capítulo 4) foi possível verificar que todos os casos em estudo apresentam uma boa eficiência de remoção de matéria orgânica, permitindo a descarga do seu efluente com uma carga poluente que cumpre com os requisitos legais de descarga em meio hídrico.

Endoscopic mucosal resection in the esophagus with a new rigide device : an animal study

Résumé: Introduction : L'utilisation de méthodes endoscopiques peu invasives est en constante augmentation pour le traitement des lésions tumorales précoces de l'oesophage. Le but du traitement comprend l'éradication complète de tous les foyers de dysplasie ou de carcinome in situ, notamment dans les métaplasies intestinales de l'oesophage de Barrett, qui peuvent dégénérer en adénocarcinome. Plusieurs techniques d'ablation de la muqueuse oesophagienne (laser, argon plasma, electrocoagulation, photothérapie dynamique, résection endoscopique) ont été utilisées jusqu'à présent, mais aucune n'a vraiment donné entière satisfaction. Les techniques actuelles de résections endoscopiques par fibroscopie sont entre autres limitées par le grand nombre de séances nécessaires à l'éradication complète de la lésion et par la petite taille des fragments de muqueuse obtenus, ce qui rend l'analyse histologique difficile. Dans notre étude animale, nous avons évalué la faisabilité, l'efficacité et la sécurité d'une méthode de résection endoscopique à l'aide d'un nouvel oesophagoscope rigide. Matériel et méthode : Le résectoscope est formé d'un oesophagoscope rigide avec une fenêtre distale transparente à travers laquelle la muqueuse et une partie de la sous-muqueuse sont aspirées et ensuite réséquées avec une anse thermique. Les diverses fenêtres utilisées ont une taille comprise entre 2.2 et 4.4 cm. Le mouton a été choisi en raison de la ressemblance de son oesophage avec celui de l'humain en ce qui concerne l'épaisseur de son oesophage et sa structure histologique. Nous avons effectué 55 résections hémi-circonférentielles sur 21 animaux et 11 résections circonférentielles sur 11 autres. La Mitomycine-C, une substance qui inhibe la prolifération fibroblastique, a été utilisée dans 8 résections circonférentielles à différents intervalles de temps afin d'empêcher la survenue de sténoses oesophagiennes. Résultats : Toutes les résections hémi-circonférentielles ont permis d'obtenir des fragments compacts de tissu avec des bords nets, ce qui permet une excellente étude histologique. La surface du tissu prélevé était en corrélation avec la taille de la fenêtre du resectoscope. Nous avons ainsi pu obtenir des fragments avec des dimensions comprises entre 6 et 12 cm2. Pour les résections circonférentielles, les tissus étaient obtenus en 2 parties, en inversant de 180° la position de l'appareil. La profondeur de la résection a été optimale dans 58 cas sur 65 avec une découpe précise au niveau de la sous-muqueuse sans lésion de la couche musculaire sous- jacente. Il n'y a pas eu de complications après les résections hémi-circonférentielles. Les complications engendrées par les résections circonférentielles (sténose, perforation) n'ont plus été rencontrées après application locale de Mitomycine-C administrée à des intervalles de temps bien précis. Conclusion : Notre méthode de résection endoscopique de la muqueuse oesophagienne offre une nouvelle approche très prometteuse par rapport aux options déjà disponibles. Elle apparaît supérieure en ce qui concerne la taille de tissu prélevé, la précision et régularité de la profondeur de résection, ainsi que la facilité et sûreté du diagnostic histologique et des marges de sécurité. Les résections hémi-circonférentielles se sont révélées sûres chez le modèle animal. Cette nouvelle technique mérite de plus amples investigations pour les résections circonférentielles avant son utilisation chez l'humain. Abstract: Background and Study Aims: We undertook this retrospective study to evaluate the frequency and prognosis of endoscopic treatment of laterally spreading tumors (LSTs) in the rectum. The recurrence rate for lesions of the lower rectum was compared with that of the upper rectum. Patients and Methods: During the period from July 1989 to June 2002, a total of 1237 rectal tumors were detected. LSTs accounted for 6.9% (85/1237) of all rectal tumors. A total of 224 tumors of the lower rectum were detected among the 1237 rectal tumors. LSTs accounted for 16.1 % (36/224) of all the lower rectal tumors. From 85 LST lesions, 67 were evaluated for their prognosis after endoscopic mucosal resection (EMR). Patients whose LSTs had been resected were followed up by endoscopy at the following frequencies: once 15 (22.4%); twice (more than 1 year), 20 (29.9%); three times (more than 3 years), 21(31.3%); and four times or more (more than 5 years), 11 (16.4%). Results: A total of 67 patients with endoscopically treated LSTs were followed up by endoscopy. We observed recurrences in two lesions of the upper rectum (2/38, 5.3%) and five lesions of the lower rectum (5/29, 17.2%) (P = 0.2364); all seven lesions were resected piecemeal. LSTs whose horizontal margin reached the pectinate line frequently recurred in the lower rectum, at a rate of 80% (4/5). However, all patients were completely cured by additional endoscopic resections, the greatest number of treatments being four. Conclusion: For early detection of recurrence and successful endoscopic cure, further colonoscopic examination within a few months after the first treatment is necessary.

Estudo da remoção de Ba2+, Ni2+, Cd2+, Cu3+, Cr3+, Sr2+, Zn2+ por eletrocoagulação em água associada à produção de petróleo

Among the waste generated in the petrochemical industry water associated with oil production is the most important. It is considered one of the great challenges due to the presence of considered toxic chemicals present in this composition. The presence of these substances difficult to reuse the water associated with the enhanced recovery processes, so that prior to their reuse or disposal, treatment is necessary. This paper aimed to study the removal efficiency of chemical species: Ba2+, Ni2+, Cd2+, Cu2+, Cr3+, Sr2+ and Zn2+, present in the composition of the water associated with oil production by electrocoagulation. The evaluation of removal of these chemical species was performed by laboratory tests using electrochemical batch reactors and continuous flow. Initial tests were performed with electrocoagulation of synthetic wastewater in batch reactor using iron electrode. Results of removal of Zn2+ and Ni2+ were 78 % and 59 % respectively. While the percentage of removed Ba2+ was 19 % by 30 minutes of treatment and by applying current of 1.10 A. The tests were performed on effluent batch reactor applying the electrochemical technique with stainless steel electrodes 304, the objective was to remove part of the dispersed oil and also of organic compounds in the effluent. Under the experimental conditions used, the maximum result was obtained TOG was 60 % and TOC was approximately 50 % compared to the initial concentration. In the experiments carried out in continuous reactor, with effluent semisynthetic, have been used electrodes of iron and aluminum and the results were 100 % removal of Cd2+, Cu2+, Cr3+ and Zn2+ and 77 % of Sr2+. These percentages were only attainable through the use of the iron electrode. However, when the electrode was replaced by aluminum, there was a reduction in the percentage of removal to 65 %, using the same flow rate and current. Therefore according to the results obtained using the iron electrode was more effective in removing these metals and the conditions of lower current and lower flow rate was satisfactory, as observed in the experimental design adopted

Tratamento eletroquímico de água produzida sintética para remoção de hidrocarbonetos policíclicos aromáticos

The aim of this work is the treatment of produced water from oil by using electrochemical technology. Produced water is a major waste generated during the process of exploration and production in the oil industry. Several approaches are being studied aiming at the treatment of this effluent; among them can be cited the biological process and chemical treatments such as advanced oxidation process and electrochemical treatments (electrooxidation, electroflotation, electrocoagulation, electrocoagulation). This work studies the application of electrochemical technology in the treatment of the synthetic produced water effluent through the action of the electron, in order to remove or transform the toxic and harmful substances from the environment by redox reactions in less toxic substances. For this reason, we used a synthetic wastewater, containing a mixture H2SO4 0,5M and 16 HPAs, which are: naphthalene, acenaphthylene, acenaphthene, fluorene, phenanthrene, anthracene, fluoranthene, pyrene, benzo (a) anthracene, chrysene, benzo(b)fluoranthene, benzo(k) fluoranthene, benzo(a)pyrene, indeno(1,2,3-cd)pyrene, dibenzo(a, h)anthracene, benzo(g, h, i)perylene. Bulk electrochemical oxidation experiments were performed using a batch electrochemical reactor containing a pair of parallel electrodes, coupled with a power supply using a magnetic stirrer for favoring the transfer mass control. As anodic material was used, a Dimensionally Stable Anode (DSA) of Ti/Pt, while as cathode was used a Ti electrode. Several samples were collected at specific times and after that, the analysis of these samples were carried out by using Gas Chromatography Coupled to Mass Spectrometry (GC - MS) in order to determine the percentage of removal. The results showed that it was possible to achieve the removal of HPAs about 80% (in some cases, more than 80%). In addition, as an indicator of the economic feasibility of electrochemical treatment the energy consumption was analyzed for each hour of electrolysis, and based on the value kWh charged by ANEEL, the costs were estimated. Thus, the treatment costs of this research were quite attractive

Degradação eletroquímica de benzeno, tolueno e xileno via oxidação eletroquímica utilizando eletrodo Ti/Pt

This work is directed to the treatment of organic compounds present in produced water from oil using electrochemical technology. The water produced is a residue of the petroleum industry are difficult to treat , since this corresponds to 98 % effluent from the effluent generated in the exploration of oil and contains various compounds such as volatile hydrocarbons (benzene, toluene, ethylbenzene and xylene), polycyclic aromatic hydrocarbons (PAHs), phenols, carboxylic acids and inorganic compounds. There are several types of treatment methodologies that residue being studied, among which are the biological processes, advanced oxidation processes (AOPs), such as electrochemical treatments electrooxidation, electrocoagulation, electrocoagulation and eletroredution. The electrochemical method is a method of little environmental impact because instead of chemical reagents uses electron through reactions of oxide-reducing transforms toxic substances into substances with less environmental impact. Thus, this paper aims to study the electrochemical behavior and elimination of the BTX (benzene, toluene and xylene) using electrode of Ti/Pt. For the experiment an electrochemical batch system consists of a continuous source, anode Ti/Pt was used, applying three densities of current (1 mA/cm2, 2,5 mA/cm2 and 5 mA/cm2). The synthetic wastewater was prepared by a solution of benzene, toluene and xylene with a concentration of 5 ppm, to evaluate the electrochemical behavior by cyclic voltammetry and polarization curves, even before assessing the removal of these compounds in solution by electrochemical oxidation. The behavior of each of the compounds was evaluated by the use of electrochemical techniques indicate that each of the compounds when evaluated by cyclic voltammetry showed partial oxidation behavior via adsorption to the surface of the Ti/Pt electrode. The adsorption of each of the present compounds depends on the solution concentration but there is the strong adsorption of xylene. However, the removal was confirmed by UV-Vis, and analysis of total organic carbon (TOC), which showed a percentage of partial oxidation (19,8 % - 99,1 % TOC removed), confirming the electrochemical behavior already observed in voltammetry and cyclic polarization curves