Ecotoxicity tests using the green algae chlorella vulgaris — a useful tool in hazardous effluents management

The treatment efficiency of laboratory wastewaters was evaluated and ecotoxicity tests with Chlorella vulgaris were performed on them to assess the safety of their environmental discharge. For chemical oxygen demand wastewaters, chromium (VI), mercury (II) and silver were efficiently removedby chemical treatments.Areduction of ecotoxicitywas achieved; nevertheless, an EC50 (effective concentration that causes a 50% inhibition in the algae growth) of 1.5% (v/v) indicated still high level of ecotoxicity. For chloride determination wastewaters, an efficient reduction of chromium and silver was achieved after treatment. Regarding the reduction of ecotoxicity observed, EC50 increased from 0.059% to 0.5%, only a 0.02% concentration in the aquatic environment would guarantee no effects. Wastewaters containing phenanthroline/iron (II) complex were treated by chemical oxidation. Treatmentwas satisfactory concerning chemical parameters, although an increase in ecotoxicitywas observed (EC50 reduced from 0.31% to 0.21%). The wastes from the kinetic study of persulphate and iodide reaction were treated with sodium bisulphite until colour was removed. Although they did not reveal significant ecotoxicity, only over 1% of the untreated waste produced observable effects over algae. Therefore, ecotoxicity tests could be considered a useful tool not only in laboratory effluents treatment, as shown, but also in hazardous wastewaters management.

From spent Mg/Al layered double hydroxide to porous carbon materials

Adsorption has been considered as an efficient method for the treatment of dye effluents, but properdisposal of the spent adsorbents is still a challenge. This work attempts to provide a facile methodto reutilize the spent Mg/Al layered double hydroxide (Mg/Al-LDH) after the adsorption of orange II(OII). Herein, the spent hybrid was carbonized under the protection of nitrogen, and then washedwith acid to obtain porous carbon materials. Thermogravimetric analysis results suggested that thecarbonization could be well achieved above 600◦C, as mass loss of the spent hybrid gradually stabilized. Therefore, the carbonization process was carried out at 600, 800, and 1000 ◦C, respectively. Scanning electron microscope showed that the obtained carbon materials possessed a crooked flaky morphology. Nitrogen adsorption–desorption results showed that the carbon materials had large BET surface area and pore volume, e.g., 1426 m2/g and 1.67 cm3/g for the sample carbonized at 800 ◦C. Moreover, the pore structure and surface chemistry compositions were tunable, as they were sensitive to the temperature. Toluene adsorption results demonstrated that the carbon materials had high efficiency in toluene removal. This work provided a facile approach for synthesizing porous carbon materials using spent Mg/Al-LDH.

Eutrofização e qualidade da água na piscicultura: consequências e recomendações

The eutrophication (cultural or anthropogenic) is induced by man and can have different origins, such as domestic sewage, industrial and agricultural activities, including the effluent still breeding systems of aquatic organisms. The expansion of aquaculture, with production of biomass and increase of nutrients in water may cause acceleration of productivity of algae, changing the ecology of aquatic systems. In addition, these waste water may present a risk to health through the transfer of pathogens from manure, plant residues, composted material, among others that are major sources of organic waste in some farming systems. Depending on the trophic level of fish ponds, which are dynamic environments, different planktonic species with short reproductive cycle and adapted to the changes contained in these systems can appear in high abundance. Water quality in the systems for raising fish is related to several factors, such as water source, management (liming, fertilizing, cleaning), cultivated species and quantity and composition of exogenous food. In order to minimize environmental impacts, there are techniques to improve the quality of water in fish farming systems and thus satisfactory answers can be obtained through the application of management practices. This paper aims to review the subject that deals with changes in water quality resulting from the activity of freshwater fish culture in Brazil. Search also recommend techniques of good management practices to minimize the impact generated by the activity.

Estudo dos parâmetros de extração de fenol de efluentes aquosos por um tensoativo não iônico

Environmental sustainability has become one of the topics of greatest interest in industry, mainly due to effluent generation. Phenols are found in many industries effluents, these industries might be refineries, coal processing, pharmaceutical, plastics, paints and paper and pulp industries. Because phenolic compounds are toxic to humans and aquatic organisms, Federal Resolution CONAMA No. 430 of 13.05.2011 limits the maximum content of phenols, in 0.5 mg.L-1, for release in freshwater bodies. In the effluents treatment, the liquid-liquid extraction process is the most economical for the phenol recovery, because consumes little energy, but in most cases implements an organic solvent, and the use of it can cause some environmental problems due to the high toxicity of this compound. Because of this, exists a need for new methodologies, which aims to replace these solvents for biodegradable ones. Some literature studies demonstrate the feasibility of phenolic compounds removing from aqueous effluents, by biodegradable solvents. In this extraction kind called "Cloud Point Extraction" is used a nonionic surfactant as extracting agent of phenolic compounds. In order to optimize the phenol extraction process, this paper studies the mathematical modeling and optimization of extraction parameters and investigates the effect of the independent variables in the process. A 32 full factorial design has been done with operating temperature and surfactant concentration as independent variables and, parameters extraction: Volumetric fraction of coacervate phase, surfactant and residual concentration of phenol in dilute phase after separation phase and phenol extraction efficiency, as dependent variables. To achieve the objectives presented before, the work was carried out in five steps: (i) selection of some literature data, (ii) use of Box-Behnken model to find out mathematical models that describes the process of phenol extraction, (iii) Data analysis were performed using STATISTICA 7.0 and the analysis of variance was used to assess the model significance and prediction (iv) models optimization using the response surface method (v) Mathematical models validation using additional measures, from samples different from the ones used to construct the model. The results showed that the mathematical models found are able to calculate the effect of the surfactant concentration and the operating temperature in each extraction parameter studied, respecting the boundaries used. The models optimization allowed the achievement of consistent and applicable results in a simple and quick way leading to high efficiency in process operation.

Assessment of by-products of chlorination and photoelectrocatalytic chlorination of an azo dye

The present work describes a more efficient methodology for the chlorination of water containing disperse dyes, where the chlorinated byproducts identified by mass spectra are compared. this investigation, we tested the degradation of Cl Disperse Blue 291 dye, 2-[(2-Bromo-4,6-dinitrophenyl)azo]-5-(diethylamino)-4-methoxyacetanilide) a commercial azo dye with mutagenic properties. The present work evaluates the photoelectrocatalytic efficiency of removing the Cl Disperse Blue 291 dye from a wastewater of the textile industry. We employed NaCl as a supporting electrolyte. It should be noted that photoelectrocatalytic techniques are non-conventional method of generating chlorine radicals. The by-products formed in this process were analyzed using spectrophotometry, liquid chromatography, dissolved organic carbon, mass spectral analysis and mutagenicity assays. The process efficiency was compared with the conventional chlorination process adopted during sewage and effluents treatment processes. This conventional chlorination process is less efficient in removing color, total organic carbon than the photoelectrochemistry technique. Furthermore, we shall demonstrate that the mutagenicity of the generated by-products obtained using photoelectrocatalysis is completely different from that obtained by the conventional oxidation of chloride ions in the drinking wafer treatment process. (C) 2012 Published by Elsevier B.V.

Redução de crômio hexavalente por substâncias húmicas aquáticas imobilizadas em aminopropil sílica

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Sewage sludge coke estimation using thermal analysis

The imposition of more stringent legislation by CETESB in the State of So Paulo (Brazil) governing the disposal and utilization of sewage sludge, coupled with the growth in its generation has prompted a drive for alternative uses of sewage sludge. One option that is especially promising, due to its potential to valorize sludge, is its conversion into carbonaceous adsorbents or coke for industrial effluents treatment. Thus, a methodology is presented to estimate the coke produced from the sludge of a sewage treatment station using thermal analysis. The used sewage sludge, which comes from aerobic treatment, was collected in the wastewater treatment station of Barueri, one of the largest of the So Paulo metropolitan area. The sludge samples were collected, dried, ground, and milled until they passed an ABNT 200 sieve. The inert ambient used during its thermal treatment produces inorganic matter and coke as residual materials. Coke formation occurs in the 200-500 A degrees C range and, between 500 and 900 A degrees C, its thermal decomposition occurs. The highest formation of coke occurs at 500 A degrees C.

Utilização de biofiltro aerado submerso no tratamento de efluentes de curtume submetido a processo de pré-tratamentos físico-químico e anaeróbio

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Produção de carvão ativado a partir da biomassa residual da castanha do Brasil (Bertholletia excelsa L.) para adsorção de cobre (II)

Produziu-se carvão ativado a partir da casca da castanha-do-Brasil (Bertholletia excelsa L.) para ser utilizado na remoção de cobre (II), no processo de adsorção em sistema de batelada. A casca é resíduo do beneficiamento da castanha, que foi coletada, selecionada, lavada em água corrente e depois secada em estufa a 150ºC por 24 h. Os carvões foram carbonizados a 400 ºC por 3 h e ativados termicamente a 800ºC em tempos de 1, 2 e 3 h, quando receberam as respectivas codificaçõesCA1, CA2 e CA3. Depois foram caracterizadas quanto: à área superficial específica, ao volume e tamanho de poros, à difração de raios-X, à microscopia eletrônica de varredura (MEV) acoplada ao EDS(sistema de energia dispersiva por raios-X) e à espectroscopia de infravermelho com transformada de Fourier (FTIR). Ensaios preliminares foram realizados para avaliar a eficiência dos carvões quanto à remoção de cobre (II) em solução sintética de concentração inicial 50 mg L^-1. Como os resultados foram satisfatórios para CA1, CA2 e CA3 (93,43, 97,23 e 96, 92 % para os respectivos carvões), decidiu-se pelo que apresentou maior percentual de remoção. O CA2 foi produzido e caracterizado quanto: às densidades reais e aparentes, à porosidade em leito fixo, ao pH, à umidade (em base úmida), às cinzas, ao carbono fixo e aos grupos funcionais pelo método de Boehm. Realizaram-se ensaios para determinar a eficiência de remoção de cobre (II) quanto à influência do diâmetro da partícula do carvão, ao pH da solução, à influência do tempo de contato e à variação da concentração inicial. Os resultados de maior percentual de remoção foram para o diâmetro 0,595≤D≤1,19mm, pH 5,09, tempo de 5 min e concentrações de 50, 100 e 150mg L^-1.O modelo cinético de adsorção que melhor se ajustou aos dados foi o de pseudo2^a ordem. Os dados experimentais apresentaram bom ajuste aos modelos matemáticos de isotermas de Langmuir e Frendlich. Sendo assim, obteve-se carvão ativado de baixo custo a partir da casca da castanha-do-Brasil a qual apresentou boa eficiência na remoção de cobre (II) (acima de 90 % para maioria das análises) possibilitando também a utilização no tratamento de efluentes.

Spatial and temporal quality of water in the Itupararanga Reservoir, Alto Sorocaba basin (SP), Brazil

Considering the great importance of the Itupararanga Reservoir, Upper Alto Sorocaba basin/SP, this study aimed to report the variations of some parameters of water quality in the spatial and temporal gradients in this multipurpose res- ervoir. The eutrophication of this reservoir was checked using the Carlson Index Modified and the results indicate that the surface water were classified as eutrophic and mesotrophic in wet and dry periods, being characterized the better quality of water in wet period. In the vertical gradient the results showed a stratiphication in all parameters analyzed, except for the electrical conductivity, with good correlation between total phosphorous and chlorophyll-a, indicating that eutrophication of the reservoir changes the conditions of algal growth, mainly in its initial area. Immediate inter- ventions are needed, which must be directed to planning of land use, domestic effluents treatment, taking to an inte- grated management of this important watershed located in the São Paulo State.

The characteristics and pollutional problems associated with petrochemical wastes; summary report.

Cover title: Petrochemical effluents treatment practices.

Eutrofização e qualidade da água na piscicultura: consequências e recomendações

The eutrophication (cultural or anthropogenic) is induced by man and can have different origins, such as domestic sewage, industrial and agricultural activities, including the effluent still breeding systems of aquatic organisms. The expansion of aquaculture, with production of biomass and increase of nutrients in water may cause acceleration of productivity of algae, changing the ecology of aquatic systems. In addition, these waste water may present a risk to health through the transfer of pathogens from manure, plant residues, composted material, among others that are major sources of organic waste in some farming systems. Depending on the trophic level of fish ponds, which are dynamic environments, different planktonic species with short reproductive cycle and adapted to the changes contained in these systems can appear in high abundance. Water quality in the systems for raising fish is related to several factors, such as water source, management (liming, fertilizing, cleaning), cultivated species and quantity and composition of exogenous food. In order to minimize environmental impacts, there are techniques to improve the quality of water in fish farming systems and thus satisfactory answers can be obtained through the application of management practices. This paper aims to review the subject that deals with changes in water quality resulting from the activity of freshwater fish culture in Brazil. Search also recommend techniques of good management practices to minimize the impact generated by the activity.

Disinfection of aquarium effluents by chlorination and UV treatment

The study was conducted to investigate the efficacy of chlorine and UV irradiation in disinfecting aquarium effluent. A non-agglutinating, a virulent strain of Aeromonas salmonicida (NCIMB 11 02) was used as the test organism. Effluents from a fish tank were inoculated with a suspension of test organisms and subsequently treated with different concentrations of hypochlorite and UV irradiation separately and simultaneously. When used alone, 1.0 ppm hypochlorite reduced the viable cell count from 6.5 log to 3.0 log within 20 minutes of contact period. On the other hand, when used in combination with UV irradiation only 0.5 ppm hypochlorite exerted the same bactericidal effect within the same contact period as was observed with 1.0 ppm hypochlorite alone. This result indicated that required dose of disinfectant for the disinfection of aquarium effluents can be considerably reduced when it is used in combination with UV irradiation.

Treatment of effluents contaminated with prions. Chemical reactor design

The control and elimination of prionic infective agents that may be present in the effluents, turns out to be a complicated mechanism inside a High Containment bological Facility. There are two ways to carry out this neutralization: Installation of thermal systems to ensure achieve a minimum temperature of 134 ° C sterilization plateau for a residence time of 18 minutes, and the use of chemical reactors based on the addition of sodium hypochlorite so the mixture maintained 2% of free chlorine during the reaction period. This study presents the design phases, elements and benefits, of a chemical reactor that allows the treatment of prion effluents in order to serve as a model to biocontainment facilities with areas of animal experimentation, who want to develop their work with prions.