Functional calibration procedure for 3D knee joint angle description using inertial sensors.

Measurement of three-dimensional (3D) knee joint angle outside a laboratory is of benefit in clinical examination and therapeutic treatment comparison. Although several motion capture devices exist, there is a need for an ambulatory system that could be used in routine practice. Up-to-date, inertial measurement units (IMUs) have proven to be suitable for unconstrained measurement of knee joint differential orientation. Nevertheless, this differential orientation should be converted into three reliable and clinically interpretable angles. Thus, the aim of this study was to propose a new calibration procedure adapted for the joint coordinate system (JCS), which required only IMUs data. The repeatability of the calibration procedure, as well as the errors in the measurement of 3D knee angle during gait in comparison to a reference system were assessed on eight healthy subjects. The new procedure relying on active and passive movements reported a high repeatability of the mean values (offset<1 degrees) and angular patterns (SD<0.3 degrees and CMC>0.9). In comparison to the reference system, this functional procedure showed high precision (SD<2 degrees and CC>0.75) and moderate accuracy (between 4.0 degrees and 8.1 degrees) for the three knee angle. The combination of the inertial-based system with the functional calibration procedure proposed here resulted in a promising tool for the measurement of 3D knee joint angle. Moreover, this method could be adapted to measure other complex joint, such as ankle or elbow.

Measurement of multi-segment foot joint angles during gait using a wearable system.

Usually the measurement of multi-segment foot and ankle complex kinematics is done with stationary motion capture devices which are limited to use in a gait laboratory. This study aimed to propose and validate a wearable system to measure the foot and ankle complex joint angles during gait in daily conditions, and then to investigate its suitability for clinical evaluations. The foot and ankle complex consisted of four segments (shank, hindfoot, forefoot, and toes), with an inertial measurement unit (3D gyroscopes and 3D accelerometers) attached to each segment. The angles between the four segments were calculated in the sagittal, coronal, and transverse planes using a new algorithm combining strap-down integration and detection of low-acceleration instants. To validate the joint angles measured by the wearable system, three subjects walked on a treadmill for five minutes at three different speeds. A camera-based stationary system that used a cluster of markers on each segment was used as a reference. To test the suitability of the system for clinical evaluation, the joint angle ranges were compared between a group of 10 healthy subjects and a group of 12 patients with ankle osteoarthritis, during two 50-m walking trials where the wearable system was attached to each subject. On average, over all joints and walking speeds, the RMS differences and correlation coefficients between the angular curves obtained using the wearable system and the stationary system were 1 deg and 0.93, respectively. Moreover, this system was able to detect significant alteration of foot and ankle function between the group of patients with ankle osteoarthritis and the group of healthy subjects. In conclusion, this wearable system was accurate and suitable for clinical evaluation when used to measure the multi-segment foot and ankle complex kinematics during long-distance walks in daily life conditions.

Avaliação de dispositivos de captura de imagens digitais para detecção colorimétrica em microzonas impressas

This report describes a study about the feasibility of using a conventional digital camera, a cell-phone camera, an optical microscope, and a scanner as digital image capture devices on printed microzones. An array containing nine circular zones was drawn using graphics software and printed onto transparency film by a laser printer. Due to its superior analytical performance, the scanner was chosen for the quantitative determination of Fe2+ in pharmaceutical samples. The data achieved using scanned images did not differ statistically from those attained by the reference spectrophotometric method at the confidence level of 0.05.

Coleópteros Saproxílicos de los Bosques de Montaña en el Norte de la Comunidad de Madrid

La fauna saproxílica ha cobrado mucha relevancia en los últimos años. Por una parte, debido a los múltiples papeles que juega en la ecología de los bosques y por otra, por encontrarse muchas especies de ese grupo amenazadas como consecuencia de la intensificación de las actividades forestales. Se supone que los bosques de Europa meridional albergan una fauna saproxílica rica y variada. Sin embargo apenas se han realizado estudios que permitan conocer la composición de las biocenosis saproxílicas, así como el estatus y grado de amenaza a que está sometida cada especie. En esta tesis se han muestreado de forma sistemática las comunidades de coleópteros saproxílicos de cuatro montes del norte de la Comunidad de Madrid, muy diferentes a pesar de su cercanía: Dehesa Bonita de Somosierra, Hayedo de Montejo, Dehesa de Madarcos y Pinar de La Maleza. Para llevar a cabo la recogida de muestras se definió una estación de muestreo tipo, compuesta por cuatro trampas aéreas con cebo oloroso, dos trampas de ventana y una trampa de embudos. En los dos primeros montes mencionados se desplegaron seis estaciones de muestreo, por sólo tres en los otros dos. El primer objetivo de esta tesis fue conocer las especies de coleópteros que constituyen la fauna de los cuatro montes estudiados. Los muestreos sistemáticos reportaron la presencia de un total de 357 especies de coleópteros saproxílicos, siendo el Hayedo de Montejo el bosque con la diversidad más alta, 220 especies; le siguen la Dehesa de Madarcos con 116; el pinar de La Maleza con 115; y la Dehesa de Somosierra con 109, si bien la fauna de este ultimo bosque podría ser mucho más variada dado que la interferencia del ganado con algunos dispositivos de captura hizo que se perdiera parte del material allí recolectado. Se han encontrado nueve especies nuevas para la fauna de la Península Ibérica, y otras muchas desconocidas previamente en el centro peninsular. Un total de 50 especies se encuentran incluidas en la Lista Roja Europea de coleópteros saproxílicos. El segundo objetivo fue estimar la riqueza de fauna de coleópteros saproxílicos en cada bosque. Partiendo de los datos de los respectivo muestreos se calcularon diferentes estimadores, paramétricos y no paramétricos, y se elaboraron las curvas de rarefacción para cada bosque y para el conjunto. El bosque con más biodiversidad ha resultado ser el Hayedo de Montejo, que albergaría entre 254 y 332 especies. En el Pinar de la Maleza se encontrarían de 132 a 223; de 128 a 205 en la Dehesa de Somosierra; y entre 134 y 188 en la Dehesa de Madarcos. Para el conjunto del área se estimó la presencia de entre 411 y 512 especies. El tercer objetivo fue evaluar la influencia de algunos factores como la especie arbórea dominante y la cantidad de madera muerta en la riqueza y diversidad de coleópteros saproxílicos. El estudio se realizó en el Hayedo de Montejo, encontrando una alta correlación positiva entre cantidad y calidad de madera muerta, y diversidad y riqueza de especies de coleópteros saproxílicos. El cuarto objetivo fue evaluar la eficacia y complementariedad de los diferentes tipos de dispositivos de captura empleados en los muestreos. El más eficaz resultó ser la trampa de ventana, seguido por la trampa aérea con cebo oloroso, y finalmente la trampa de embudos. La mayor complementariedad se encontró entre trampas de ventana y aéreas con cebo oloroso. No obstante, si se quiere optimizar la exhaustividad del inventario no se debe prescindir de ninguno de los sistemas. En cualquier caso, puede afirmarse que la efectividad de los tres tipos de dispositivos de captura utilizados en los muestreos fue baja, pues para la gran mayoría de especies presentes se capturó un número de ejemplares realmente bajo. El bajo rendimiento de captura implica un bajo impacto sobre las poblaciones de las especies muestreadas, y esto supone una importante ventaja desde el punto de vista de la conservación. Finalmente, se dejan algunas recomendaciones de manejo a aplicar en cada uno de los montes con el fin de preservar o mejorar los hábitats utilizables por la fauna saproxílica que garanticen el mantenimiento y mejora de dichas comunidades. ABSTRACT The saproxylic fauna has become increasingly important in recent years. It has been due, on the one hand, to the multiple roles they play in the forest ecosystems and, on the other, because of the large proportion of endangered saproxylic species as a result of the intensification of forestry. It is generally assumed that southern Europe forests are home to a rich and diverse saproxylic fauna. However, there are hardly any studies leading to reveal the composition of saproxylic biocenosis, or the stage and extent of the threat each species is suffering. For the purpose of this thesis the communities of saproxylic beetles of four mountain forests in northern Comunidad de Madrid have been systematically sampled: Dehesa Bonita de Somosierra, Hayedo de Montejo, Dehesa de Madarcos and Pinar de La Maleza. They are very different from each other in spite of not being too far apart. In order to carry out sample collection, a standard sampling station was defined as follows: four smelly bait aerial traps, two window traps and one funnel trap. Six sampling stations were deployed in each of the first two forests mentioned above; put only three in each of the other two. The first aim of this thesis was to determine the composition of saproxylic beetles fauna inhabiting each of the four forests studied. Systematic sampling reported the presence of a total of 357 species of saproxylic beetles. Hayedo de Montejo, with 220 species, is the forest with the highest diversity, followed by Dehesa de Madarcos, 116; Pinar de La Maleza, 115, and Dehesa de Somosierra, 109. The fauna of the latter forest, however, could be much more varied, since cattle interference with some capture devices caused the loss of part of the material collected there. Nine new species in the fauna of the Iberian Peninsula were found, and many others previously unknown in the center of the Peninsula. A total of 41 of those species are included in the European Red List of saproxylic beetles. The second aim was to estimate the richness of saproxylic (beetle) fauna in each forest. From the data of the respective sampling, different parametric and nonparametric estimators were calculated, and rarefaction curves for each forest, as well as for the four of them together, were drawn. The most biodiverse forest turned out to be Hayedo de Montejo, which houses between 254 and 332 species. In Pinar de La Maleza, between 132 and 223 species were found; between 128 and 205 in Dehesa de Somosierra, and between 134 and 188 in Dehesa de Madarcos. The estimated diversity of species for the whole area ranges from 411 to 512. The third aim was to evaluate the influence of such factors as the dominant tree species and the amount of dead wood in the richness and diversity of saproxylic beetles. The study was conducted at Hayedo de Montejo, finding a high positive correlation between quantity and quality of coarse woody debris and diversity and richness of saproxylic beetle species. The fourth aim was to evaluate the effectiveness and complementarity of the different sampling methods used in this research work. The most effective proved to be the window trap, followed by the smelly bait aerial trap and the funnel trap, in that order. The greater complementarity was found between window and aerial traps. However, in order to optimize the completeness of the inventory, neither of the systems should be discarded. Nevertheless, the effectiveness of the three types of capture devices used in this piece of research was on the whole rather low, since for the vast majority of species, a significant low number of specimens were captured. Poor trapping performance implies a low impact on the populations of the sampled species, and this is an important advantage in terms of conservation. Finally, this thesis gives some recommendations with regard to the management of each of those four forests, leading to preserve and improve the habitats of the saproxylic wildlife and so ensure the maintenance and growth of their communities.

Arcabouço para construção de jogos ubíquos com foco em reabilitação

Dissertação (mestrado)—Universidade de Brasília, Instituto de Ciências Exatas, Departamento de Ciência da Computação, 2016.

Assessment of bioaerosols and inhalable dust exposure in Swiss sawmills

An assessment of wood workers' exposure to airborne cultivable bacteria, fungi, inhalable endotoxins and inhalable organic dust was performed at 12 sawmills that process mainly coniferous wood species. In each plant, samples were collected at four or five different work sites (debarking, sawing, sorting, planing and sawing cockpit) and the efficiency of sampling devices (impinger or filter) for determining endotoxins levels was evaluated. Results show that fungi are present in very high concentrations (up to 35 000 CFU m(-3)) in all sawmills. We also find that there are more bioaerosols at the sorting work site (mean +/- SD: 7723 +/- 9919 CFU m(-3) for total bacteria, 614 +/- 902 CFU m(-3) for Gram-negative, 19 438 +/- 14 246 CFU m(-3) for fungi, 7.0 +/- 9.0 EU m(-3) for endotoxin and 2.9 +/- 4.8 g m(-3) for dust) than at the sawing station (mean +/- SD: 1938 +/- 2478 CFU m(-3) for total bacteria, 141 +/- 206 CFU m(-3) for Gram-negative, 12 207 +/- 10 008 CFU m(-3) for fungi, 2.1 +/- 1.9 EU m(-3) for endotoxin and 0.75 +/- 0.49 mg m(-3) for dust). At the same time, the species composition and concentration of airborne Gram-negative bacteria were studied. Penicillinium sp. were the predominant fungi, while Bacillus sp. and the Pseudomonadacea family were the predominant Gram-positive and Gram-negative bacteria encountered, respectively. [Authors]

Enhanced capture of healthcare-related harms and injuries in the 11th revision of the International Classification of Diseases (ICD-11).

The World Health Organization (WHO) plans to submit the 11th revision of the International Classification of Diseases (ICD) to the World Health Assembly in 2018. The WHO is working toward a revised classification system that has an enhanced ability to capture health concepts in a manner that reflects current scientific evidence and that is compatible with contemporary information systems. In this paper, we present recommendations made to the WHO by the ICD revision's Quality and Safety Topic Advisory Group (Q&S TAG) for a new conceptual approach to capturing healthcare-related harms and injuries in ICD-coded data. The Q&S TAG has grouped causes of healthcare-related harm and injuries into four categories that relate to the source of the event: (a) medications and substances, (b) procedures, (c) devices and (d) other aspects of care. Under the proposed multiple coding approach, one of these sources of harm must be coded as part of a cluster of three codes to depict, respectively, a healthcare activity as a 'source' of harm, a 'mode or mechanism' of harm and a consequence of the event summarized by these codes (i.e. injury or harm). Use of this framework depends on the implementation of a new and potentially powerful code-clustering mechanism in ICD-11. This new framework for coding healthcare-related harm has great potential to improve the clinical detail of adverse event descriptions, and the overall quality of coded health data.

Studies on Soft Bycatch Reduction Devices for Selective Trawling

Trawling, though an efficient method of fishing, is known to be one of the most non-selective methods of fish capture. The bulk of the wild caught penaeid shrimps landed in India are caught by trawling.In addition to shrimps, the trawler fleet also catches considerable amount of non-shrimp resources. The term bycatch means that portion of the catch other than target species caught while fishing, which are either retained or discarded. Bycatch discards is a serious problem leading to the depletion of the resources and negative impacts on biodiversity. In order to minimize this problem, trawling has to be made more selective by incorporating Bycatch Reduction Devices (BRDs). There are several advantages in using BRDs in shrimp trawling. BRDs reduce the negative impacts of shrimp trawling on marine community. Fishers could benefit economically from higher catch value due to improved catch quality, shorter sorting time, lower fuel costs, and longer tow duration. Adoption of BRDs by fishers would forestall criticism by conservation groups against trawling.

The development of a new dust uplift scheme in the Met Office Unified Model

Aeolian mineral dust aerosol is an important consideration in the Earth's radiation budget as well as a source of nutrients to oceanic and land biota. The modelling of aeolian mineral dust has been improving consistently despite the relatively sparse observations to constrain them. This study documents the development of a new dust emissions scheme in the Met Office Unified ModelTM (MetUM) based on the Dust Entrainment and Deposition (DEAD) module. Four separate case studies are used to test and constrain the model output. Initial testing was undertaken on a large dust event over North Africa in March 2006 with the model constrained using AERONET data. The second case study involved testing the capability of the model to represent dust events in the Middle East without being re-tuned from the March 2006 case in the Sahara. While the model is unable to capture some of the daytime variation in AERONET AOD there is good agreement between the model and observed dust events. In the final two case studies new observations from in situ aircraft data during the Dust Outflow and Deposition to the Ocean (DODO) campaigns in February and August 2006 were used. These recent observations provided further data on dust size distributions and vertical profiles to constrain the model. The modelled DODO cases were also compared to AERONET data to make sure the radiative properties of the dust were comparable to observations. Copyright © 2009 Royal Meteorological Society and Crown Copyright

Application of an auditory steady-state response test to evaluate the attenuation of hearing protection devices

This research aims to present a new method to get real attenuation of hearing protection devices, with good reproducibility and a small standard deviation, without relying on skills and cooperation individual. Thus the authors performed tests in 10 individuals without protection and after with two kinds of ear protections (ear plug and ear muffs), to get the threshold limit value in each of the 3 stages. For this, the research used an electrophysical exam, normally used in speech therapy, named ASSR (auditory steady-state response). The principle of this exam is put on individual’s head 3 electrodes, to capture electrical signs directly in auditory nerve. In summary, the authors presented the final results. The method proposed by ANSI (American National Standards Institute) indicated an attenuation of 27.6 dB for ear plugs, while the value found in this work was 16 dB; and for ear muffs, the ANSI method indicated 29.8 dB while the value found here was 28.5 dB.

Influence of pattern gradation on the design of piezocomposite energy harvesting devices using topology optimization

Piezoelectric materials can be used to convert oscillatory mechanical energy into electrical energy. Energy harvesting devices are designed to capture the ambient energy surrounding the electronics and convert it into usable electrical energy. The design of energy harvesting devices is not obvious, requiring optimization procedures. This paper investigates the influence of pattern gradation using topology optimization on the design of piezocomposite energy harvesting devices based on bending behavior. The objective function consists of maximizing the electric power generated in a load resistor. A projection scheme is employed to compute the element densities from design variables and control the length scale of the material density. Examples of two-dimensional piezocomposite energy harvesting devices are presented and discussed using the proposed method. The numerical results illustrate that pattern gradation constraints help to increase the electric power generated in a load resistor and guides the problem toward a more stable solution. (C) 2012 Elsevier Ltd. All rights reserved.

Vibrating Membrane Devices Deliver Aerosols More Efficient than Standard Devices: A Study in a Neonatal Upper Airway Model

Abstract Background: Aerosol therapy in preterm infants is challenging, as a very small proportion of the drug deposits in the lungs. Aim: Our aim was to compare efficiency of standard devices with newer, more efficient aerosol delivery devices. Methods: Using salbutamol as a drug marker, we studied two prototypes of the investigational eFlow(®) nebulizer for babies (PARI Pharma GmbH), a jet nebulizer (Intersurgical(®) Cirrus(®)), and a pressurized metered dose inhaler (pMDI; GSK) with a detergent-coated holding chamber (AeroChamber(®) MV) in the premature infant nose throat-model (PrINT-model) of a 32-week preterm infant (1,750 g). A filter or an impactor was placed below the infant model's "trachea" to capture the drug dose or particle size, respectively, that would have been deposited in the lung. Results: Lung dose (percentage of nominal dose) was 1.5%, 6.8%, and 18.0-20.6% for the jet nebulizer, pMDI-holding chamber, and investigational eFlow nebulizers, respectively (p<0.001). Jet nebulizer residue was 69.4% and 10.7-13.9% for the investigational eFlow nebulizers (p<0.001). Adding an elbow extension between the eFlow and the model significantly lowered lung dose (p<0.001). A breathing pattern with lower tidal volume decreased deposition in the PrINT-model and device residue (p<0.05), but did not decrease lung dose. Conclusions: In a model for infant aerosol inhalation, we confirmed low lung dose using jet nebulizers and pMDI-holding chambers, whereas newer, more specialized vibrating membrane devices, designed specifically for use in preterm infants, deliver up to 20 times more drug to the infant's lung.

Speed-independent gait identification for mobile devices

Due to the intensive use of mobile phones for diferent purposes, these devices usually contain condential information which must not be accessed by another person apart from the owner of the device. Furthermore, the new generation phones commonly incorporate an accelerometer which may be used to capture the acceleration signals produced as a result of owner s gait. Nowadays, gait identication in basis of acceleration signals is being considered as a new biometric technique which allows blocking the device when another person is carrying it. Although distance based approaches as Euclidean distance or dynamic time warping have been applied to solve this identication problem, they show di±culties when dealing with gaits at diferent speeds. For this reason, in this paper, a method to extract an average template from instances of the gait at diferent velocities is presented. This method has been tested with the gait signals of 34 subjects while walking at diferent motion speeds (slow, normal and fast) and it has shown to improve the performance of Euclidean distance and classical dynamic time warping.

Depth filtering for auto-stereoscopic mobile devices

In this work we address a scenario where 3D content is transmitted to a mobile terminal with 3D display capabilities. We consider the use of 2D plus depth format to represent the 3D content and focus on the generation of synthetic views in the terminal. We evaluate different types of smoothing filters that are applied to depth maps with the aim of reducing the disoccluded regions. The evaluation takes into account the reduction of holes in the synthetic view as well as the presence of geometrical distortion caused by the smoothing operation. The selected filter has been included within an implemented module for the VideoLan Client (VLC) software in order to render 3D content from the 2D plus depth data format.

Work at hand: an exploration of gesture in the context of work and everyday life to inform the design of gestural input devices

This research explores gestures used in the context of activities in the workplace and in everyday life in order to understand requirements and devise concepts for the design of gestural information appliances. A collaborative method of video interaction analysis devised to suit design explorations, the Video Card Game, was used to capture and analyse how gesture is used in the context of six different domains: the dentist's office; PDA and mobile phone use; the experimental biologist's laboratory; a city ferry service; a video cassette player repair shop; and a factory flowmeter assembly station. Findings are presented in the form of gestural themes, derived from the tradition of qualitative analysis but bearing some similarity to Alexandrian patterns. Implications for the design of gestural devices are discussed.