Optimum mix design of concrete made with dune sand as fine aggregate

The use of dune sand for replacing ordinary fine aggregate in concrete has environmental benefits and the feasibility has been demonstrated in China and some Middle East countries. However, the use of dune sand tends to decrease the engineering properties (compressive strength and workability) of concrete. To improve engineering properties of dune sand concrete (DSC), the current paper is to check which strength andslump levels can be obtained by optimization of mix proportions. Results show that the ratio of cement to sand (C/S) has significant influence on the engineering properties of DSC. At low C/S ratio, the engineeringproperties of DSC are inferior to those of concretes made with normal sand (NSC). However, when C/S ratio exceeds 0.75, DSC has comparable or even better engineering properties compared to NSC. In the range ofinvestigated C/S ratio, DSC has comparable tensile splitting strength and elastic modulus to its reference NSC.Based on the experimental results, the Australia dune sand can be used as fine aggregate whenever mix proportions are properly controlled.

The properties of fly ash based geopolymer mortars made with dune sand

Geopolymer cement utilises industrial by-products and is associated with low CO2 emissions. The use of dune sand as fine aggregate could reduce the environmental impact of mining activities. The present study is to examine the feasibility of using dune sand in geopolymer-based construction materials. The geopolymer mortars made with dune sand (DSM) were prepared by using alkali activators of different cations(Na, K and Na/K). In order to compare, the corresponding geopolymer mortars made with normal sand (NSM) were also prepared. It was found that dune sand has little influence on the strength of geopolymer mortars, especially for K based mortars. However, the alkali cation has significant influence on the compressive strength of geopolymer mortars. This influence was found to be correlated to porosity. Low compressive strength is associated with high porosity. For all investigated alkali cations, the tensile strengths of DSM compare favourably to those predicted by the relevant Standards for construction materials. Based on the experimental results, Australian dune sand can be used as fine aggregate for the production of geopolymer based construction materials.

The properties of fly ash based geopolymer mortars made with dune sand

This paper reports the properties of fly ash based geopolymer mortars made with dune sand. The geopolymer mortars of different cation type, namely sodium based (Na), potassium based (K) and a mixed Na/K, were prepared with dune sand (DS) and river sand (RS). The corresponding geopolymer pastes were also prepared. A series of tests including compressive strength, modulus of elasticity, splitting tensile strength, microanalysis (using scanning electron microscopy), porosity (using mercury intrusion porosimetry), sorptivity and air void (using section analysis method) were carried out. The results showed a strong correlation between strength and porosity of geopolymeric materials. The addition of DS had influences on the chemical compositions and physical properties of geopolymer mortars. These influences were dependent on the type of cation. Based on the results of mechanical properties, DS can be utilised as the fine aggregate for the production of geopolymer based construction material.

塔克拉玛干沙漠地球化学研究

The Taklamakan Desert, lying in the center Tarim Basin of sourthern Xinjiang, is the largest sand sea in China and well known in the world as its inclemency. For understanding the formation and evolution of the Taklamakan Desert, it is very important to identify the provenance of aeolian sediments in the extensive dune fields, but the opinions from earlier studies are quite different. In this study, we examined the major- and trace-element compositions, mineral compositions and grain-size distributions of some Quaternary aeolian and nonaeolian sediments collected from the Taklamakan Desert, together with the variation of chemical and mineralogical compositions of different grain-size fraction. At the same time, we also studied the chemistries of some natural water samples (river water and groundwater) with the items of TDS, pH, Alkalinity, conductivity and major cation and anion compositions. Our results of analysis show some significant opinions as follow: Most of the frequency-distribution curves of grain size of dune sand samples are simgle peak, but that of the river and lacustrine sediment are most double peak or multi-peak. The grain-size distribution of dunefield sand changed gradually from north to south with the major wind direction in large scale, but there are many differences in regional scale. The major, REE, trace element compositions and mineral compositions are very different among the coarse, fine fraction and bulk samples due to the influence of grain-size. Most of the fine fractions are geochemically homogenous, but the coarse fractions and bulk samples are heterogenous. All the surface and ground waters are limnetic or sub-salty, their chemical compositions are mainly controlled by rock-weathering and crystallization- evaporation processes, and mainly come from the evaporate, while the contributions of the carbonate and silicate are little, excluding the influence on oasis water by carbonate. The mineral compositions of selected samples are stable, mainly composed of the strongly resistant mineral types. The mineral maturity of them are more immature at whole compared with other sandy sediments in the world, and they have experienced less degree of chemical weathering and recycling, being lying in the early stage of continental weathering. Among these sediments, the river sediments are relatively primitive. The sources of these sediments are maybe mainly terrigenous, silicic and subaluminous/ metalunious rocks, such as the granodiorite and its metamorphic rock. The geochemical compositions of dunefield sand are similar with those of the river sediments and dune sands near the river way; There are not only the resemblances but also the differences on geochemistry and granularity between north and south dunesands; The sediments from same section have different age but same trace-element compositions; The sediments from the south edge of Tarim Basin are all somewhat geochemically similar with the palaeo-river-sediment on the south edge of studying area. The REE data support the idea that the south dunesands are a little older than the north dunesands, and the tectonic settings of source area are mainly active continental margin based on the major-element compositions, so they indicate that the sediment of Taklamakan Desert maybe come mainly from the rock-weathering production of north part of the Kunlun Mountains. Compared with the sands of other dune field in north of China, the sands of the Taklamakan Desert are distinct by REE composition, but similar with the Luochuan loess, center China, and the two sandy dusts of Beijing, eastern China.

细粒沉积物多组分粒度特征及其成因机制研究

By using high-resolution laser grain size instrument Mastersizer 2000, the grain size distribution of windblown depositions (loess and sandy dunes), aqueous sediments (lake, river, riverside and foreshore sand), weathering crust, sloping materials and other fine-grain sediments are systemically measured. The multimodal characteristics of grain size distribution of these sediments are carefully studied. The standard patterns and their grain size characteristics of various sediments are systemically summarized. The discrepancies of multimodal distribution among windblown depositions, aqueous sediments and other sediments are concluded and the physical mechanisms of grain size multimodal distribution of various sediments are also discussed in this paper. The major conclusions are followed: 1. The multimodal characteristic of grain size distribution is a common feature in all sediments and results from properties of transportation medium, dynamic intensity, transportation manner and other factors. 2. The windblown depositions are controlled by aerodynamic forcing, resulting in that the median size of the predominant mode gradually decreases form sandy dunes to loess. Similarly, the aqueous sediments are impacted by dynamic forces of water currents and the median grain size of the predominant mode decreases gradually from river to lake sediments. Because the kinetic viscidity of air is lower than of water, the grain size of modes of windblown depositions is usually finer than that of corresponding modes of aqueous sediments. Typical characteristics of sediments grain size distribution of various sediments have been summarized in the paper: (1) Suspended particles which diameters are less than 75μm are dominant in loess and dust. There are three modes in loess’ grain size distribution: fine, median and coarse (the median size is <1μm、1-10μm、10-75μm, respectively). The coarse mode which percentage is larger than that of others is controlled by source distance and aerodynamic intensity of dust source areas. Some samples also have a saltation mode which median size is about 300-500μm. Our analysis demonstrates that the interaction of wind, atmospheric turbulence, and dust grain gravity along the dust transportation path results in a multimodal grain size distribution for suspended dust. Changes in the median sizes of the coarse and medium modes are related to variation in aerodynamic forcing (lift force related to vertical wind and turbulence) during dust entrainment in the source area and turbulence intensity in the depositional area. (2) There is a predominant coarse saltation mode in grain size distribution of sandy dunes, which median size is about 100-300μm and the content is larger than that of other modes. The grain size distribution curve is near axis symmetric as a standard logarithm normal function. There are some suspended particles in some samples of sandy dunes, which distribution of the fine part is similar to that of loess. Comparing with sandy samples of river sediments, the sorting property of sandy dunes is better than of river samples although both they are the saltation mode. Thus, the sorting property is a criterion to distinguish dune sands and river sands. (3) There are 5~6 modes (median size are <1μm, 1-10μm, 10-70μm, 70-150μm, 150-400μm, >400μm respectively) in grain size distribution of lacustrine sediments. The former 4 modes are suspensive and others are saltated. Lacustrine sediments can be divided into three types: lake shore facies, transitional facies and central lake facies. The grain size distributions of the three facies are distinctly different and, at the same time, the transition among three modes is also clear. In all these modes, the third mode is a criteria to identify the windblown deposition in the watershed. In lake shore sediments, suspended particles are dominant, a saltation mode sometimes occurs and the fourth mode is the most important mode. In the transitional facies, the percentage of the fourth mode decreases and that of the second mode increases from lake shore to central lake. In the central lake facies, the second mode is dominant. A higher content of the second mode indicates its position more close to the central lake. (4) The grain size distribution of river sediments is the most complex. It consist of suspension, saltation and rolling modes. In most situations, the percentage of the saltation mode is larger than that of other modes. The percentage of suspension modes of river sediments is more than of sandy dunes. The grain size distribution of river sediments indicates dynamic strength of river currents. If the fourth mode is dominant, the dynamic forcing of river is weaker, such as in river floodplain. If the five or sixth mode is dominant, the water dynamic forcing of rivers is strong. (5) Sediments can be changed by later forcing in different degree to form some complicated deposition types. In the paper, the grain size distribution of aqueous sediments of windblown deposition, windblown sediments of aqueous deposition, weathering crust and slope materials are discussed and analyzed. 3. The grain size distribution characteristics of different sediments are concluded: (1) Modal difference: Usually there are suspended and saltation modes in the windblown deposition. The third mode is dominant in loess dust and the fifth mode is predominant in sandy dunes. There are suspended, saltation and rolling particles in aqueous sediments. In lacustrine sediments, the second and fourth mode are predominant for central lake facies or lake shore facies, respectively. In river sediments, the fourth, or fifth, or sixth mode is predominant. Suspended modes: the grain size of suspended particles of windblown depositions usually is less than 75μm. The content of suspended particles is lower or none in sandy dunes. However, suspended particles of aqueous sediments may reach 150μm. Difference in grain size of suspended modes represents difference between transitional mediums and the strength of dynamic forcing. Saltation modes: the median size of saltation mode of sandy dunes fluctuates less than that of river sediments. (2) Loess dust and lacustrine sediment: Their suspended particles are clearly different. There is an obvious pit between the second and the third modes in grain size distribution of lacustrine sediments. The phenomenon doesn’t occur in loess dust. In lacustrine sediments, the second mode can be a dominant mode, such as central lake facies, and contents of the second and the third modes change reversely. However, the percentage of the third mode is always the highest in loess dust. (3) Dune Sand and fluvial sand: In these two depositions, the saltation particles are dominant and the median sizes of their saltation modes overlay in distribution range. The fifth mode of dune sand fluctuates is sorted better than that of fluvial sand. (4) Lacustrine and fluvial sediments: In lacustrine sediments, there are 5-6 modes and suspended particles can be predominant. The second mode is dominant in central lake facies and the third mode is dominant in lake shore facies. Saltation or roll modes occurred in central lake facies may indicate strong precipitation events. In fluvial sediments, saltation particles (or rolling particles) usually dominant. 4. A estimation model of lake depth is firstly established by using contents of the second, the third and the fourth modes. 5. The paleoenvironmental history of the eastern part of SongLiao basin is also discussed by analyzing the grain size distribution of Yushu loess-like sediments in Jilin. It was found that there is a tectonic movement before 40ka B.P. in SongLiao basin. After the movement, loess dust deposited in Yushu area as keerqin desert developed. In recent 2000 years, the climate became drier and more deserts activated in the eastern part of Song-Liao basin.

An extension of the well-known quaternary section at Godrevy, St Ives Bay, West Cornwall: analysis and review

The well-known Quaternary section at Godrevy, west Cornwall has been often described during the past half century, however, a further section, about a kilometre to the south is considered for the first time since a brief mention at the beginning of the last century. This 200m long exposure rests upon a raised shore platform and consists of a basal raised beach and littoral sand, overlain by a local diamict revealing evidence of post-depositional frost disturbance and finally Holocene dune sand. It is proposed that this Strap Rock site be included within the general discussion of the Godrevy section.

The Wabar impact craters, Saudi Arabia, revisited

The very young Wabar craters formed by impact of an iron meteorite and are known to the scientific community since 1933. We describe field observations made during a visit to the Wabar impact site, provide analytical data on the material collected, and combine these data with poorly known information discovered during the recovery of the largest meteorites. During our visit in March 2008, only two craters (Philby-B and 11 m) were visible; Philby-A was completely covered by sand. Mapping of the ejecta field showed that the outcrops are strongly changing over time. Combining information from different visitors with our own and satellite images, we estimate that the large seif dunes over the impact site migrate by approximately 1.0–2.0 m yr␣1 southward. Shock lithification took place even at the smallest, 11 m crater, but planar fractures (PFs) and undecorated planar deformation features (PDFs), as well as coesite and stishovite, have only been found in shock-lithified material from the two larger craters. Shock-lithified dune sand material shows perfectly preserved sedimentary structures including cross-bedding and animal burrows as well as postimpact structures such as open fractures perpendicular to the bedding, slickensides, and radiating striation resembling shatter cones. The composition of all impact melt glasses can be explained as mixtures of aeolian sand and iron meteorite. We observed a partial decoupling of Fe and Ni in the black impact glass, probably due to partitioning of Ni into unoxidized metal droplets. The absence of a Ca-enriched component demonstrates that the craters did not penetrate the bedrock below the sand sheet, which has an estimated thickness of 20–30 m.

Distribution of benthos in late Quaternary turbidite layers of sediment cores from the North-West African continental margin

The CaCO3-contents and the fractions > 40 µm have been analysed from 5 kastenloten, one piston core and two kastengreifer taken between Senegal and Cape Verde Islands. Numerous benthonic and planktonic organisms and different terrigenous components have been distinguished. The four cores off Senegal reach middle Wuerm sediments; cores GIK12329-6 and TAG72-1 reach the V-zone and core GIK12331-4 the X-zone (Eem); the two kastengreifer contain sediments of Holocene age. Correlation of the cores has been made. Holocene sedimentation rates decrease from the shallow cores (6-11 cm/1000 years) to the deep-sea (1-2 cm/1000 years). The following climatic variations could be deduced from the sediments off the Senegal: during Holocene climate was in general as today, the Senegal river transporting fine grained material to the sea. The upper Wuerm was arid with no river influence but with red dune sand transported to the continental slope. During middle Wuerm the climate was humid again. The deep-sea cores have been influenced by eolian material from arid regions during glacial and interglacial periods, indicated by relatively high "Wuestenquarz-numbers". However, during Wuerm "Wuestenquarz-numbers" are higher than during Holocene and Eem, indicating that more intensely red coloured sediment was exposed to wind activity on the continent during this period. Varying amounts of terrigenous material and CaCO3-contents indicate varying wind strengths (lower in Holocene and Eem than during Wuerm). The boundary between humid and arid Wuerm climate was at approximately 20 °N. Influence of upwelling is difficult to establish in the sediments off Senegal, because river influence, while increasing fertility also dilutes the diatoms which are typical for upwelling. High amounts of organic carbon, low plankton/benthos ratios of foraminifers and low plankton foraminifer/radiolarian ratios in Holocene sections might be interpreted as influenced by upwelling. Turbidites occur in cores 72 and 31 and at the Holocene/Pleistocene boundary of core GIK12329-6. Their composition indicates provenance from the continental shelf of the Cape Verde Islands for core 31 and the continental shelf and slope off Senegal for core TAG72-1. Volcanic material, rare in the normal pelagic sediment of core GIK12331-4 is more frequent in the turbidites.

Characteristics and distribution of Neogene turbidites at ODP Site 108-657

Numerous and variable silty-sandy siliciclastic turbidites were observed in Neogene pelagic sediments (late Miocene to Holocene) at Site 657: (1) thick-bedded, coarse-grained and thin-bedded, fine-grained turbidites; and (2) turbidites composed of eolian dune sand and shallow-water bioclasts or of fluvial-sand or mixed sandy component assemblages. The stratigraphic distribution of these turbidites indicates five periods during which climatic conditions and material sources change. Turbidite occurrence prior to 6.2 Ma (late Miocene) is sparse; the deposits contain coarse and fine-grained turbidites with quartz grains of eolian or mixed origin suggesting the existence of arid conditions at about 8.5 and 6.5 Ma. A coarse-grained turbidite of fluvial origin, recording a humid climate, occurs at about 6.2 Ma. During the early Pliocene, turbidites are frequent (15/Ma); they contain only fine-grained sequences comprising material of mixed origin, which indicates a more humid climate perhaps. The late Pliocene starts with rare coarse-grained turbidites of wind-transported sand while the uppermost Pliocene deposits show a higher frequency of fine-grained sequences (10/0.7 Ma) composed mainly of fluvial material. During the early Pleistocene, similar high turbidite frequency was observed (20/1.3 Ma) but with a total lack of eolian supply. During the last 0.7 Ma, the frequency decreases and the sequences are characterized by highly variable sediment components that could be related to strong variations of climatic conditions. The sedimentary characteristics of turbidites are mainly controlled by sediment source and climate. The frequency must be influenced by sea-level variations, by cyclic processes of climatic origin, and possibly by variations in the continental slope morphology. Clay mineral assemblages suggest a south Saharan source of terrigenous material during the late Miocene and the Pliocene and a northwest Saharan source during the Pleistocene.

Geomorphological constraining of tsunami (?) run-up in the Alcantarilha coastal lowland (Central Algarve, Portugal)

The Alcantarilha lowland, partly barred by a well developed barrier, including foredunes covering Pleistocene-Holocene beachrock and aeolianite, develops across the Alcantarilha infilled estuary, the beach-dune extending further SE until the Salgados lagoon. A topographic and coring survey revealed a peculiar feature at the leeward toe of the dune ridge close to the inlet area: a sandy fan with location, shape and morphology suggesting emplacement by single or multiple overwash of the barrier tip rather than tidal forcing. Its storm or tsunami origin and age are under investigation, and the only time-constrain available at present is that it should post-date ca. 6600 cal BP, the most recent in situ aeolianite (Moura et al., 2007) dated so far. METHODS, DATA SET AND RESULTS The fan boundaries are distinctive in aerial photos and satellite images: it is roughly ellipsoidal, ~200 m wide and ~300 m elongated paralleling the shoreline, rising ~ 0.9-1.2 m above the surrounding floodplain surface. Detailed topography shows that its short axis aligns with SW-NE elongated (though irregular) depressions in the dune crest, which link the beach with the fan. This could have favoured funnelling of, or erosion by, water overtopping the barrier but, in either case, the fan should correspond to extreme and abrupt event(s) of coastal flooding. 18 trenches and cores were performed in the exposed area of the fan and nearby flood plain to obtain samples and data on its sedimentology, lithostratigraphy and geometry. The fan consists of well sorted and rounded sand (Fig. 2). It thins away and wedges out landwards of the apex (located near Alc29T) where it is partly covered by dune sand. Its lower boundary is undulating and marked by textural contrast between sand (fan) and underlying mud (alluvial/lagoonal); an accumulation of marine-sourced perforated pebbles showing limited lateral continuity may pinpoint this boundary near the foredune (core Alc 25, ca. 80 m westward of profile in Fig.1); mud-balls were also observed immediately above this surface in cores and trenches. As the washover was probably emplaced in a barred lagoonal/estuarine floodplain setting, the fan’s northern outer belt is enclosed by low-energy sediments (not shown in Fig. 2).

Monitoring report: sand dune reconstruction and restoration, at the Moss Landing Marine Laboratories

The Plan for Sand Dune Reconstruction and Restoration (and Biological Assessment) at Moss Landing Marine Laboratories (ABA Consultants, April 1, 1992) described reconstruction of dune contours and biological restoration with native dune plants to be carried out over the 8 acre site formerly occupied by the marine labs (prior to the Loma Prieta earthquake of October 1989). The plan called for annual reports in letter form which would present data on plant abundance, a short narrative description of changes on the site, progress towards recovery of the plant community, and assessment of progress based on restoration goals and further steps to be taken. This monitoring report [dated April 25, 1994] addresses those points and also contains a summary of other activities integral in dune restoration -- education, public participation, school and conservation organization field trips, as well as the associated activities of restoration, plant collecting, propagation, and weed control.