Quality of natural coffee subjected to different rest periods during the drying process

O parcelamento da secagem pode ser eficiente tanto no que diz respeito à qualidade final do café, quanto na redução do consumo específico de energia. Diante disso, objetivou-se, com o presente trabalho, avaliar o efeito do teor de água dos frutos no momento da interrupção da secagem e do período de repouso até a retomada da secagem na qualidade do café natural, por meio da análise sensorial e dos testes de condutividade elétrica e lixiviação de potássio. Frutos de café maduros foram colhidos manual e seletivamente e, em seguida, secados ao sol em terreiros de concreto por dois dias e, então, submetidos à secagem mecânica em secadores de camada fixa. Quando o café atingiu os teores de água de 20%, 17% e 14% (base úmida, bu), a secagem foi interrompida e o café permaneceu em repouso por cinco, quinze e trinta dias e, posteriormente, foi secado em secadores mecânicos até o teor de água de 11% (bu). O controle constituiu-se na secagem completa em terreiro. Observou-se que as combinações entre o menor teor de água e o maior período de repouso e entre o maior teor de água e o menor período de repouso, proporcionam menores valores de lixiviação de potássio. A qualidade da bebida melhora progressivamente com o aumento do período de repouso. A interrupção da secagem com teores de água de 17% e 20% (bu) não altera a qualidade do café natural, comparativamente à secagem completa em terreiro.

COMPARATIVE-STUDY OF CA4Y6(SIO4)(6)O-A PHOSPHORS PREPARED BY SOL-GEL AND DRY METHODS (A=PB2+,EU3+, TB3+,DY3+)

Ca4Y6(SiO4)(6)O:A (A = Pb2+, Eu3+, Tb3+, Dy3+) phosphors have been prepared by two methods: the sol-gel method and the conventional dry method. The crystallization processes and the luminescence characteristics of the phosphors were studied, The sol-gel method features low-temperature formation of the phosphor, leading to successful preparation of Pb2+-activated phosphors which could not be prepared by the dry method at high temperature. The (4f)(8-)(4f)(7)(5d)(1) absorption band of Tb3+ and the charge-transfer (CT) band of Eu3+ have higher energies and narrower half-widths in the sol-gel-derived phosphors than in the phosphors prepared by the dry method, respectively. The Tb3+ and Dy3+ ions show stronger emission in the former than in the latter. Both the yellow-to-blue intensity ratio (Y:B) of Dy3+ and the red-to-orange intensity ratio (R:O) of Eu3+ in the sol-gel-derived phosphors are smaller than those for the phosphors derived by the dry method.

Qualidade do café natural e despolpado após secagem em terreiro e com altas temperaturas

Objetivou-se no presente trabalho verificar a qualidade do café natural e despolpado durante a secagem em terreiro e secagem com ar aquecido a 40º e 60ºC. O trabalho foi realizado no Departamento de Engenharia e no Pólo de Tecnologia em Pós-Colheita do Café da Universidade Federal de Lavras (UFLA). A colheita do café, cultivar Topázio, foi seletiva. Parte do café foi despolpado e outra parte processado de forma natural. Uma parcela de cada tipo de café foi conduzida para a secagem em terreiro e outra parcela para secagem com temperaturas de 40ºC e 60ºC. Para avaliação da qualidade, foram feitos teste de condutividade elétrica e lixiviação de potássio; determinação de acidez titulável total; teste de acidez graxa; açúcares totais e redutores. Os resultados obtidos permitem concluir que: o tempo para secagem é afetado pelos diferentes tipos de secagem e processamentos; a condutividade elétrica, a lixiviação de potássio, a acidez titulável total e a acidez graxa aumentam com a elevação da temperatura de secagem, independente do tipo de processamento; os açúcares redutores e os açúcares totais diminuem com o aumento da tem peratura de secagem independente do tipo de processamento; a secagem com temperatura de 60ºC afetou negativamente a qualidade do café.

Contamination routes and control of Listeria monocytogenes in Food Production

Listeria monocytogenes is the causative agent of the severe foodborne infection listeriosis. The number of listeriosis cases in recent years has increased in many European countries, including Finland. Contamination of the pathogen needs to be minimized and growth to high numbers in foods prevented in order to reduce the incidence of human cases. The aim of this study was to evaluate contamination routes of L. monocytogenes in the food chain and to investigate methods for control of the pathogen in food processing. L. monocytogenes was commonly found in wild birds, the pig production chain and in pork production plants. It was found most frequently in birds feeding at landfill site, organic farms, tonsil samples, and sites associated with brining. L. monococytogenes in birds, farms, food processing plant or foods did not form distinct genetic groups, but populations overlapped. The majority of genotypes recovered from birds were also detected in foods, food processing environments and other animal species and birds may disseminate L. monocytogenes into food chain. Similar genotypes were found in different pigs on the same farm, as well as in pigs on farms and later in the slaughterhouse. L. monocytogenes contamination spreads at farm level and may be a contamination source into slaughterhouses and further into meat. Incoming raw pork in the processing plant was frequently contaminated with L. monocytogenes and genotypes in raw meat were also found in processing environment and in RTE products. Thus, raw material seems to be a considerable source of contamination into processing facilities. In the pork processing plant, the prevalence of L. monocytogenes increased in the brining area, showing that the brining was an important contamination site. Recovery of the inoculated L. monocytogenes strains showed that there were strain-specific differences in the ability to survive in lettuce and dry sausage. The ability of some L. monocytogenes strains to survive well in food production raises a challenge for industry, because these strains can be especially difficult to remove from the products and raises a need to use an appropriate hurdle concept to control most resistant strains. Control of L. monocytogenes can be implemented throughout the food chain. Farm-specific factors affected the prevalence of L. monocytogenes and good farm-level practices can therefore be utilized to reduce the prevalence of this pathogen on the farm and possibly further in the food chain. Well separated areas in a pork production plant had low prevalences of L. monocytogenes, thus showing that compartmentalization controls the pathogen in the processing line. The food processing plant, especially the brining area, should be subjected to disassembling, extensive cleaning and disinfection to eliminate persistent contamination by L. monocytogenes, and replacing brining with dry-salting should be considered. All of the evaluated washing solutions decreased the populations of L. monocytogenes on precut lettuce, but did not eliminate the pathogen. Thus, the safety of fresh-cut produce cannot rely on washing with disinfectants, and high-quality raw material and good manufacturing practices remain important. L. monocytogenes was detected in higher levels in sausages without the protective culture than in sausages with this protective strain, although numbers of L. monocytogenes by the end of the ripening decreased to the level of < 100 MPN/g in all sausages. Protective starter cultures provide an appealing hurdle in dry sausage processing and assist in the control of L. monocytogenes.

Electrochemical Detection of Bisphenol A Using Graphene-Modified Glassy Carbon Electrode

Graphene's nano-dimensional nature and excellent electron transfer properties underlie its electrocatalytic behavior towards certain substances. In this light, we have used graphene in the electrochemical detection of bisphenol A. Graphene sheets were produced via soft chemistry route involving graphite oxidation and chemical reduction. X-ray diffraction, Fourier transform infra-red (FT-IR) and Raman spectroscopy were used for the characterization of the as-synthesized graphene. Graphene exhibited amorphous structure in comparison with pristine graphite from XRD spectra. FTIR showed that graphene exhibits OH and COOH groups due to incomplete reduction. Raman spectroscopy revealed that multi-layered graphene was produced due to low intensity of the 2D-peak. Glassy carbon electrode was modified with graphene by a simple drop and dry method. Cyclic voltammetry was used to study the electrochemical properties of the prepared graphene-modified glassy carbon electrode using potassium ferricyanide as a redox probe. The prepared graphene- modified glassy carbon electrode exhibited more facile electron kinetics and enhanced current of about 75% when compared to the unmodified glassy carbon electrode. The modified electrode was used for the detection of bisphenol A. Under the optimum conditions, the oxidation peak current of bisphenol A varied linearly with concentration over a wide range of 5 x 10(-8) mol L-1 to 1 x 10(-6) mol L-1 and the detection limit of this method was as low as 4.689 x 10(-8) M. This method was also employed to determine bisphenol A in a real sample

High-performance nanowire oxide photo-thin film transistor.

A gate-modulated nanowire oxide photosensor is fabricated by electron-beam lithography and conventional dry etch processing.. The device characteristics are good, including endurance of up to 10(6) test cycles, and gate-pulse excitation is used to remove persistent photoconductivity. The viability of nanowire oxide phototransistors for high speed and high resolution applications is demonstrated, thus potentially expanding the scope of exploitation of touch-free interactive displays.

双聚焦偏移速度估计与可分表示叠前弹性反演

In exploration seismology, the geologic target of oil and gas reservoir in complex medium request the high accuracy image of the structure and lithology of the medium. So the study of the prestack image and the elastic inversion of seismic wave in the complex medium come to the leading edge. The seismic response measured at the surface carries two fundamental pieces of information: the propagation effects of the medium and the reflections from the different layer boundaries in the medium. The propagation represent the low-wavenumber component of the medium, it is so-called the trend or macro layering, whereas the reflections represent the high-wavenumber component of the medium, it is called the detailed or fine layering. The result of migration velocity analysis is the resolution of the low-wavenumber component of the medium, but the prestack elastic inversion provided the resolution of the high-wavvenumber component the medium. In the dissertation, the two aspects about the migration velocity estimation and the elastic inversion have been studied.Firstly, any migration velocity analysis methods must include two basic elements: the criterion that tell us how to know whether the model parameters are correct and the updating that tell us how to update the model parameters when they are incorrect, which are effected on the properties and efficiency of the velocity estimation method. In the dissertation, a migration velocity analysis method based on the CFP technology has been presented in which the strategy of the top-down layer stripping approach are adapted to avoid the difficult of the selecting reduce .The proposed method has a advantage that the travel time errors obtained from the DTS panel are defined directly in time which is the difference with the method based on common image gather in which the residual curvature measured in depth should be converted to travel time errors.In the proposed migration velocity analysis method, the four aspects have been improved as follow:? The new parameterization of velocity model is provided in which the boundaries of layers are interpolated with the cubic spline of the control location and the velocity with a layer may change along with lateral position but the value is calculated as a segmented linear function of the velocity of the lateral control points. The proposed parameterization is suitable to updating procedure.? The analytical formulas to represent the travel time errors and the model parameters updates in the t-p domain are derived under local lateral homogeneous. The velocity estimations are iteratively computed as parametric inversion. The zero differential time shift in the DTS panel for each layer show the convergence of the velocity estimation.? The method of building initial model using the priori information is provided to improve the efficiency of velocity analysis. In the proposed method, Picking interesting events in the stacked section to define the boundaries of the layers and the results of conventional velocity analysis are used to define the velocity value of the layers? An interactive integrate software environment with the migration velocity analysis and prestack migration is built.The proposed method is firstly used to the synthetic data. The results of velocity estimation show both properties and efficiency of the velocity estimation are very good.The proposed method is also used to the field data which is the marine data set. In this example, the prestack and poststack depth migration of the data are completed using the different velocity models built with different method. The comparison between them shows that the model from the proposed method is better and improves obviously the quality of migration.In terms of the theoretical method of expressing a multi-variable function by products of single-variable functions which is suggested by Song Jian (2001), the separable expression of one-way wave operator has been studied. A optimization approximation with separable expression of the one-way wave operator is presented which easily deal with the lateral change of velocity in space and wave number domain respectively and has good approach accuracy. A new prestack depth migration algorithm based on the optimization approximation separable expression is developed and used to testing the results of velocity estimation.Secondly, according to the theory of the seismic wave reflection and transmission, the change of the amplitude via the incident angle is related to the elasticity of medium in the subsurface two-side. In the conventional inversion with poststack datum, only the information of the reflection operator at the zero incident angles can be used. If the more robust resolutions are requested, the amplitudes of all incident angles should be used.A natural separable expression of the reflection/transmission operator is represented, which is the sum of the products of two group functions. One group function vary with phase space whereas other group function is related to elastic parameters of the medium and geological structure.By employing the natural separable expression of the reflection/transmission operator, the method of seismic wave modeling with the one-way wave equation is developed to model the primary reflected waves, it is adapt to a certain extent heterogeneous media and confirms the accuracy of AVA of the reflections when the incident angle is less than 45'. The computational efficiency of the scheme is greatly high.The natural separable expression of the reflection/transmission operator is also used to construct prestack elastic inversion algorithm. Being different from the AVO analysis and inversion in which the angle gathers formed during the prstack migration are used, the proposed algorithm construct a linear equations during the prestack migration by the separable expression of the reflection/transmission operator. The unknowns of the linear equations are related to the elasticity of the medium, so the resolutions of them provided the elastic information of the medium.The proposed method of inversion is the same as AVO inversion in , the difference between them is only the method processing the amplitude via the incident angle and computational domain.

Effect of two different rice dehusking procedures on total arsenic concentration in rice

Pollution of subterranean water by arsenic (As) in Asia has resulted in the worst chemical disaster in human history. For populations living on subsistence rice diets, As contamination of rice grain contributes greatly to dietary As exposure. The main objectives of this study were to compare two dehusking processes: (a) wet process (soaking of rice, boiling and mechanical hulling) and (b) dry process (mechanical hulling), and recommend the method leading to a lower As content in commercial rice. In general, hulling of paddy rice (373 mu g As kg(-1)) significantly decreased As content in rice grain (311 mu g As kg(-1)). The final As concentrations in boiled rice (final product of the wet process) and atab rice (dry process) were 332 and 290 mu g kg(-1). Thus, the dry method is recommended for dehusking paddy rice if not As-free water is available. However, villagers can reduce the As content in the wet system by discarding the soaking water and using new water for the light boiling. Finally, it is not recommended to use rice husk for feeding animals because the As concentration is very high, approximately 1,000 mu g As kg(-1).

STUDIES ON THE QUALITY AND PROCESS CONTROL FACTORS DURING THE PRODUCTION AND STORAGE OF SALTED DRIED FISH PRODUCTS

In this study the quality and process control factors during the production and storage of salted dried fish products. The study reveals that quantity of dry fish production in the state is decreasing and dry fish processing industry should be encouraged by central and state governments. The dry and wet salting may be carried out to a period of 4 to 8 hours respectively and time may depend on temperature, size, and concentration of medium. Demand is an unavoidable factor for sale of fish. The packed dry salted lots kept at room temperature are useful only for 20 days. The refrigerator- stored lots had more storage life and nutritional content are good up to 3 months. The cold storage stored dry salted lot had more storage life than the wet salted lot. The use of preservatives in salting is encouraged to reduce pH. The low temperature preservation maintains the nutritional value and quality for long period. It further encourages the labeling of nutritional value of dry fish as in tinned products.

Avaliação dos efeitos ambientais nas propriedades do compósito de poliamida 6,6/fibras de carbono

This graduation work done study of polyamide 6.6/composite carbon fibres, since its processing, characterization of the main properties. Besides the influence of temperature, UV radiation, salt spray and moisture on the mechanical and viscoelastic behavior. To achieve this goal, the first composite was processed from the heat compression molding using known variables of the process and using the empirical method to find the best value for other parameters. The method processing molding was chosen because it common in composites processing in order to evaluate the influence of crystallinity of the properties that influence the mechanical and viscoelastic behavior laminates. From the obtained laminate specimens were evaluated in weathering, such as: in hygrothermal chamber, UV, salt spray and thermal shock. In another step, the effect produced by these constraints were evaluated by optical microscopy, ultrasound, dynamic mechanical analysis and vibration tests. This project was conducted at the Department of Technology and Materials of UNESP in Guaratingueta, where all the equipment and techniques for the implementation of this project met available. After the tests proved the applicability of the composite polyamide 6.6/carbon fibers in aeronautical applications with resistance the main climatic influences

Critical Issues of Centralized and Cloudified LTE-FDD Radio Access Networks

Cloudification of the Centralized-Radio Access Network (C-RAN) in which signal processing runs on general purpose processors inside virtual machines has lately received significant attention. Due to short deadlines in the LTE Frequency Division Duplex access method, processing time fluctuations introduced by the virtualization process have a deep impact on C-RAN performance. This paper evaluates bottlenecks of the OpenAirInterface (OAI is an open-source software-based implementation of LTE) cloud performance, provides feasibility studies on C-RAN execution, and introduces a cloud architecture that significantly reduces the encountered execution problems. In typical cloud environments, the OAI processing time deadlines cannot be guaranteed. Our proposed cloud architecture shows good characteristics for the OAI cloud execution. As an example, in our setup more than 99.5% processed LTE subframes reach reasonable processing deadlines close to performance of a dedicated machine.

Investigation on performance characteristics of dense graded hot mix asphalt with RAP and Crumb Rubber

The use of recycled materials in asphalt mixtures such as reclaimed asphalt pavements (RAP) have become widely accepted as a replacement for virgin asphalt binder or virgin aggregates. In this study, the RAP content was 30%, and CR additives were blended with the soft unmodified binder by using dry processes. The objective of this study was to investigate and evaluate the engineering properties of dry method application of crumb rubber influences on reclaimed asphalt pavement (RAP) mixtures. To evaluate the effect of rubber-bitumen interaction on the mixture’s mechanical properties, a laboratory investigation has been conducted on a range of dense graded and 30% RAP by dry process crumb rubber modified (CRM) asphalt mixtures containing 0% (control), 1% crumb rubber by the total aggregate mass. The experimental program in this research include the binder extraction for estimating the amount of aged binder in the both fine and coarse RAP material. Before extracting the binder the RAP sieve analysis, have been done to provide the Black grading curve. In continue after the binder extraction the material sieved again to providing the white curve. The comparison of Black and White curve indicated that there is a remarkable difference between the aggregate grading even for the fine RAP. The experimental program was continued by fabricating 12 specimens in different 4 types of mixtures. For the first group no RAP, no rejuvenator and no crumb rubber were used. For the second group 30% of virgin aggregates substituted by RAP material and the third group was similar to the second group just with 0.01% rejuvenator. the forth group was the group, which in that the specimens contain RAP, rejuvenator and crumb rubber. Finally the specimens were tested for Indirect tensile strength. The results indicated that the addition of crumb rubber increased the optimum amount of binder in the mixture with 30% RAP.

Chemical modification of smectite clays

Today, speciality use organoclays are being developed for an increasingly large number of specific applications. Many of these, including use in cosmetics, polishes, greases and paints, require that the material be free from abrasive impurities so that the product retains a smooth `feel'. The traditional `wet' method preparation of organoclays inherently removes abrasives naturally present in the parent mineral clay, but it is time-consuming and expensive. The primary objective of this thesis was to explore the alternative `dry' method (which is both quicker and cheaper but which provides no refining of the parent clay) as a process, and to examine the nature of the organoclays produced, for the production of a wide range of commercially usable organophilic clays in a facile way. Natural Wyoming bentonite contains two quite different types of silicate surface (that of the clay mineral montmorillonite and that of a quartz impurity) that may interact with the cationic surfactant added in the `dry' process production of organoclays. However, it is oil shale, and not the quartz, that is chiefly responsible for the abrasive nature of the material, although air refinement in combination with the controlled milling of the bentonite as a pretreatment may offer a route to its removal. Ion exchange of Wyoming bentonite with a long chain quaternary ammonium salt using the `dry' process affords a partially exchanged, 69-78%, organoclay, with a monolayer formation of ammonium ions in the interlayer. Excess ion pairs are sorbed on the silicate surfaces of both the clay mineral and the quartz impurity phases. Such surface sorption is enhanced by the presence of very finely divided, super paramagnetic, Fe2O3 or Fe(O)(OH) contaminating the surfaces of the major mineral components. The sorbed material is labile to washing, and induces a measurable shielding of the 29Si nuclei in both clay and quartz phases in the MAS NMR experiment, due to an anisotropic magnetic susceptibility effect. XRD data for humidified samples reveal the interlamellar regions to be strongly hydrophobic, with the by-product sodium chloride being expelled to the external surfaces. Many organic cations will exchange onto a clay. The tetracationic cyclophane, and multipurpose receptor, cyclobis(paraquat-p-phenylene) undergoes ion exchange onto Wyoming bentonite to form a pillared clay with a very regular gallery height. The major plane of the cyclophane is normal to the silicate surfaces, thus allowing the cavity to remain available for complexation. A series of group VI substituted o-dimethoxybenzenes were introduced, and shown to participate in host/guest interactions with the cyclophane. Evidence is given which suggests that the binding of the host structure to a clay substrate offers advantages, not only of transportability and usability but of stability, to the charge-transfer complex which may prove useful in a variety of commercial applications. The fundamental relationship between particle size, cation exchange capacity and chemical composition of clays was also examined. For Wyoming bentonite the extent of isomorphous substitution increases with decreasing particle size, causing the CEC to similarly increase, although the isomorphous substitution site: edge site ratio remains invarient throughout the particle size range studied.

Characterisation and processing of amorphous binary mixtures with low glass transition temperature

The number of drug substances in formulation development in the pharmaceutical industry is increasing. Some of these are amorphous drugs and have glass transition below ambient temperature, and thus they are usually difficult to formulate and handle. One reason for this is the reduced viscosity, related to the stickiness of the drug, that makes them complicated to handle in unit operations. Thus, the aim in this thesis was to develop a new processing method for a sticky amorphous model material. Furthermore, model materials were characterised before and after formulation, using several characterisation methods, to understand more precisely the prerequisites for physical stability of amorphous state against crystallisation. The model materials used were monoclinic paracetamol and citric acid anhydrate. Amorphous materials were prepared by melt quenching or by ethanol evaporation methods. The melt blends were found to have slightly higher viscosity than the ethanol evaporated materials. However, melt produced materials crystallised more easily upon consecutive shearing than ethanol evaporated materials. The only material that did not crystallise during shearing was a 50/50 (w/w, %) blend regardless of the preparation method and it was physically stable at least two years in dry conditions. Shearing at varying temperatures was established to measure the physical stability of amorphous materials in processing and storage conditions. The actual physical stability of the blends was better than the pure amorphous materials at ambient temperature. Molecular mobility was not related to the physical stability of the amorphous blends, observed as crystallisation. Molecular mobility of the 50/50 blend derived from a spectral linewidth as a function of temperature using solid state NMR correlated better with the molecular mobility derived from a rheometer than that of differential scanning calorimetry data. Based on the results obtained, the effect of molecular interactions, thermodynamic driving force and miscibility of the blends are discussed as the key factors to stabilise the blends. The stickiness was found to be affected glass transition and viscosity. Ultrasound extrusion and cutting were successfully tested to increase the processability of sticky material. Furthermore, it was found to be possible to process the physically stable 50/50 blend in a supercooled liquid state instead of a glassy state. The method was not found to accelerate the crystallisation. This may open up new possibilities to process amorphous materials that are otherwise impossible to manufacture into solid dosage forms.

Wood properties and processing outcomes for plantation grown African mahogany (Khaya senegalensis) trees from Clare, Queensland (18 and 20 year-old trees) and Katherine, Northern Territory (14 year-old trees).

Khaya senegalensis, African mahogany, a high-value hardwood, was introduced in the Northern Territory (NT) in the 1950s; included in various trials there and at Weipa, Q in the 1960s-1970s; planted on ex mine sites at Weipa (160 ha) until 1985; revived in farm plantings in Queensland and in trials in the NT in the 1990s; adopted for large-scale, annual planting in the Douglas-Daly region, NT from 2006 and is to have the planted area in the NT extended to at least 20,000 ha. The recent serious interest from plantation growers, including Forest Enterprises Australia Ltd (FEA), has seen the establishment of some large scale commercial plantations. FEA initiated the current study to process relatively young plantation stands from both Northern Territory and Queensland plantations to investigate the sawn wood and veneer recovery and quality from trees ranging from 14 years (NT – 36 trees) to 18-20 years (North Queensland – 31 trees). Field measures of tree size and straightness were complemented with log end splitting assessment and cross-sectional disc sample collection for laboratory wood properties measurements including colour and shrinkage. End-splitting scores assessed on sawn logs were relatively low compared to fast grown plantation eucalypts and did not impact processing negatively. Heartwood proportion in individual trees ranged from 50% up to 92 % of butt cross-sectional disc area for the visually-assessed dark coloured central heartwood and lighter coloured transition wood combined. Dark central heartwood proportion was positively related to tree size (R2 = 0.57). Chemical tests failed to assist in determining heartwood – sapwood boundary. Mean basic density of whole disc samples was 658 kg/m3 and ranged among trees from 603 to 712 kg/m3. When freshly sawn, the heartwood of African mahogany was orange-red to red. Transition wood appeared to be pinkish and the sapwood was a pale yellow colour. Once air dried the heartwood colour generally darkens to pinkish-brown or orange-brown and the effect of prolonged time and sun exposure is to darken and change the heartwood to a red-brown colour. A portable colour measurement spectrophotometer was used to objectively assess colour variation in CIE L*, a* and b* values over time with drying and exposure to sunlight. Capacity to predict standard colour values accurately after varying periods of direct sunlight exposure using results obtained on initial air-dried surfaces decreased with increasing time to sun exposure. The predictions are more accurate for L* values which represent brightness than for variation in the a* values (red spectrum). Selection of superior breeding trees for colour is likely to be based on dried samples exposed to sunlight to reliably highlight wood colour differences. A generally low ratio between tangential and radial shrinkages was found, which was reflected in a low incidence of board distortion (particularly cupping) during drying. A preliminary experiment was carried out to investigate the quality of NIR models to predict shrinkage and density. NIR spectra correlated reasonably well with radial shrinkage and air dried density. When calibration models were applied to their validation sets, radial shrinkage was predicted to an accuracy of 76% with Standard Error of Prediction of 0.21%. There was also a strong predictive power for wood density. These are encouraging results suggesting that NIR spectroscopy has good potential to be used as a non-destructive method to predict shrinkage and wood density using 12mm diameter increment core samples. Average green off saw recovery was 49.5% (range 40 to 69%) for Burdekin Agricultural College (BAC) logs and 41.9% (range 20 to 61%) for Katherine (NT) logs. These figures are about 10% higher than compared to 30-year-old Khaya study by Armstrong et al. (2007) however they are inflated as the green boards were not docked to remove wane prior to being tallied. Of the recovered sawn, dried and dressed volume from the BAC logs, based on the cambial face of boards, 27% could potentially be used for select grade, 40% for medium feature grade and 26% for high feature grades. The heart faces had a slightly higher recovery of select (30%) and medium feature (43%) grade boards with a reduction in the volume of high feature (22%) and reject (6%) grade boards. Distribution of board grades for the NT site aged 14 years followed very similar trends to those of the BAC site boards with an average (between facial and cambial face) 27% could potentially be used for select grade, 42% for medium feature grade, 26% for high feature grade and 5% reject. Relatively to some other subtropical eucalypts, there was a low incidence of borer attack. The major grade limiting defects for both medium and high feature grade boards recovered from the BAC site were knots and wane. The presence of large knots may reflect both management practices and the nature of the genetic material at the site. This stand was not managed for timber production with a very late pruning implemented at about age 12 years. The large amount of wane affected boards is indicative of logs with a large taper and the presence of significant sweep. Wane, knots and skip were the major grade limiting defects for the NT site reflecting considerable amounts of sweep with large taper as might be expected in younger trees. The green veneer recovered from billets of seven Khaya trees rotary peeled on a spindleless lathe produced a recovery of 83% of green billet volume. Dried veneer recovery ranged from 40 to 74 % per billet with an average of 64%. All of the recovered grades were suitable for use in structural ply in accordance to AS/NZ 2269: 2008. The majority of veneer sheets recovered from all billets was C grade (27%) with 20% making D grade and 13% B grade. Total dry sliced veneer recovery from the logs of the two largest logs from each location was estimated to be 41.1%. Very positive results have been recorded in this small scale study. The amount of colour development observed and the very reasonable recoveries of both sawn and veneer products, with a good representation of higher grades in the product distribution, is encouraging. The prospects for significant improvement in these results from well managed and productive stands grown for high quality timber should be high. Additionally, the study has shown the utility of non-destructive evaluation techniques for use in tree improvement programs to improve the quality of future plantations. A few trees combined several of the traits desired of individuals for a first breeding population. Fortunately, the two most promising trees (32, 19) had already been selected for breeding on external traits, and grafts of them are established in the seed orchard.