Permability and Porosity of Devonian Dolomites in Northwestern Montana

The purpose of this investigation is to record data per­taining to porosity and permeability derived from physical tests performed on Devonian dolomites occurring in northwestern Montana, and to subsequently summarize the results obtained as an aid in determining the possibility of those dolomites being suitable reservoir rocks for oil and gas accumulation.

The magnesium isotope composition of diagenetic dolomites from ODP Hole 112-685A and 201-1230A of the Peru Margin

The magnesium isotope composition of diagenetic dolomites and their adjacent pore fluids were studied in a 250 m thick sedimentary section drilled into the Peru Margin during Ocean Drilling Program (ODP) Leg 201 (Site 1230) and Leg 112 (Site 685). Previous studies revealed the presence of two types of dolomite: type I dolomite forms at ~ 6 m below seafloor (mbsf) due to an increase in alkalinity associated with anaerobic methane oxidation, and type II dolomite forms at focused sites below ~ 230 mbsf due to episodic inflow of deep-sourced fluids into an intense methanogenesis zone. The pore fluid delta 26Mg composition becomes progressively enriched in 26Mg with depth from values similar to seawater (i.e. -0.8 per mil, relative to DSM3 Mg reference material) in the top few meters below seafloor (mbsf) to 0.8 ± 0.2 per mil within the sediments located below 100 mbsf. Type I dolomites have a delta 26Mg of -3.5 per mil, and exhibit apparent dolomite-pore fluid fractionation factors of about -2.6 per mil consistent with previous studies of dolomite precipitation from seawater. In contrast, type II dolomites have delta 26Mg values ranging from -2.5 to -3.0 per mil and are up to -3.6 per mil lighter than the modern pore fluid Mg isotope composition. The enrichment of pore fluids in 26Mg and depletion in total Mg concentration below ~ 200 mbsf is likely the result of Mg isotope fractionation during dolomite formation, The 26Mg enrichment of pore fluids in the upper ~ 200 mbsf of the sediment sequence can be attributed to desorption of Mg from clay mineral surfaces. The obtained results indicate that Mg isotopes recorded in the diagenetic carbonate record can distinguish near surface versus deep formed dolomite demonstrating their usefulness as a paleo-diagenetic proxy.

Inclination of the two main components of magnetization and 87Sr/86Sr ratios for dolomites at DSDP Hole 77-536

Site 536 terminated in a shallow-water dolomite of unknown age. Paleomagnetic measurements combined with strontium isotope analyses suggest that the dolomite was deposited in the Middle Jurassic to Early Cretaceous time interval. However, the assumptions required to reach this determination make these results less than conclusive.

Magnesium isotope ratios of pore-fluids and dolomites

Magnesium concentrations in deep-sea sediment pore-fluids typically decrease down core due to net precipitation of dolomite or clay minerals in the sediments or underlying crust. To better characterize and differentiate these processes, we have measured magnesium isotopes in pore-fluids and sediment samples from Ocean Drilling Program sites (1082, 1086, 1012, 984, 1219, and 925) that span a range of oceanographic settings. At all sites, magnesium concentrations decrease with depth. At sites where diagenetic reactions are dominated by the respiration of organic carbon, pore-fluid d26Mg values increase with depth by as much as 2 per mil. Because carbonates preferentially incorporate 24Mg (low d26Mg), the increase in pore-fluid d26Mg values at these sites is consistent with the removal of magnesium in Mg-carbonate (dolomite). In contrast, at sites where the respiration of organic carbon is not important and/or weatherable minerals are abundant, pore-fluid d26Mg values decrease with depth by up to 2 per mil. The decline in pore-fluid d26Mg at these sites is consistent with a magnesium sink that is isotopically enriched relative to the pore-fluid. The identity of this enriched magnesium sink is likely clay minerals. Using a simple 1D diffusion-advection-reaction model of pore-fluid magnesium, we estimate rates of net magnesium uptake/removal and associated net magnesium isotope fractionation factors for sources and sinks at all sites. Independent estimates of magnesium isotope fractionation during dolomite precipitation from measured d26Mg values of dolomite samples from sites 1082 and 1012 are very similar to modeled net fractionation factors at these sites, suggesting that local exchange of magnesium between sediment and pore-fluid at these sites can be neglected. Our results indicate that the magnesium incorporated in dolomite is 2.0-2.7 per mil depleted in d26Mg relative to the precipitating fluid. Assuming local exchange of magnesium is minor at the rest of the studied sites, our results suggest that magnesium incorporated into clay minerals is enriched in d26Mg by 0 per mil to +1.25 per mil relative to the precipitating fluid. This work demonstrates the utility of magnesium isotopes as a tracer for magnesium sources/sinks in low-temperature aqueous systems.

Mechanism of red colouration in Tovel-See (”Conclusions” only) [Translation from: Archiv fur Hydrobiologie 38 299-302, 1941]

Cases of red colouration in small lake basins, due to the abundant appearance of microorganisms have long been known. Usually it is caused by a fast, sudden, intensive propagation (so called ”bloom”) of Cyanophycae and bacteria. (e.g. Oscillatoracae, thiobacteria etc.). An exception to this is the red colouration of Tovel-See, an alpine lake basin in the Dolomites of the Brenta group (Trentino), lying at a height of 1178 m and hidden in the woodland of a valley. Here the red bloom has a double rhythm: a daily and a yearly rhythm. The colouration of one part of the lake takes place in the warmest months of the year (i.e. July, August, September) and in the middle hours of the day. The immediate origin of the bloom has been known for a long time: it is caused by the Peridinacae Glenodinium sanguineum. This paper describes the phenomenon of red colouration of the lake and discusses its conditions.

Estudo diagenético aplicado ao Membro Maruim da Formação Riachuelo , na parte terrestre da sub-bacia de Sergipe, Brasil

O Membro Maruim da Formação Riachuelo (Neoalbiano), na parte terrestre da Sub-bacia de Sergipe, contém fácies de água rasa compostas, principalmente, por rudstone/grainstone oncolítico oolítico, com baixo conteúdo e variedade de bioclastos. A correlação dos afloramentos e análise petrográfica detalhada, envolvendo catodoluminescência, microscopia eletrônica de varredura (MEV) e estudos isotópicos e análise química elementar, permitiram a reconstrução da história diagenética do intervalo estudado. As rochas carbonáticas do Membro Maruim estão completamente afetadas por processos diagenéticos associados aos estágios eogenético, mesogenético e telogenético. A dolomitização foi um dos principais produtos diagenéticos observados no estágio eogenético e encontra-se substituindo total ou parcialmente os calcários do Membro Maruim. A dolomitização concentra-se no topo dos ciclos deposicionais descritos na área de estudo e diminuem gradativamente para a base dos mesmos. As relações entre a porosidade e a dolomitização foram estudadas com base nas comparações da fábrica cristalina da dolomita preservada nos afloramentos estudados. Os resultados isotópicos das dolomitas indicam que o processo de dolomitização ocorreu a partir do refluxo de salmouras em um ambiente ligeiramente hipersalino (penesalino). As áreas mais próximas ao contato com a salmoura, fonte dos fluidos dolomitizantes, exibem menor desenvolvimento de porosidade, uma vez que nessas regiões ocorreriam processos de superdolomitização (Pedreira Carapeba). Nestas áreas a assinatura isotópica do carbono e do oxigênio é muito positiva (o valor do δ13C varia de 2.37 a 4.83 e o valor do δ18O oscila entre 0.61 e 3.92), indicando que os processos diagenéticos tardios não teriam alterado significativamente a assinatura isotópica original. As dolomitas geradas nas áreas afastadas da salmoura (pedreiras Massapé, Inorcal I, Inorcal II, Inhumas e Santo Antônio) exibem um maior desenvolvimento de porosidade e têm uma composição isotópica de carbono e oxigênio mais negativa (o valor do δ13C varia de -5.66 a 2.61 e o valor do δ18O oscila entre -4.25 e 0.38). A assinatura isotópica das dolomitas descritas nestas pedreiras também se encontra alterada por processos de dedolomitização. Os cimentos diagenéticos precipitados durante o estágio mesogenético foram os principais responsáveis pela obliteração da porosidade primária e secundária dos calcários do Membro Maruim. Adicionalmente, estes cimentos diagenéticos tardios calcitizaram as dolomitas, fechando parcialmente a porosidade secundária das mesmas. A porosidade das rochas carbonáticas também se encontra fortemente reduzida pela compactação mecânica e química. A dissolução foi o único processo que levou à geração de porosidade secundária no estágio telogenético, porém em porcentagens muito baixas. As fácies dolomíticas são as que apresentam maior desenvolvimento de porosidade secundária, como consequência dos processos de dissolução no ambiente telogenético. A dissolução compreende um dos últimos eventos diagenéticos identificados no intervalo estudado.

Utilização de imagem do sensor Aster para discriminação espectral de rochas carbonáticas aflorantes na região Noroeste do Estado do Rio de Janeiro

Este trabalho teve como objetivo geral avaliar o potencial das imagens do sensor ASTER, utilizando a região do infravermelho de ondas curtas (SWIR), para discriminação espectral de rochas carbonáticas aflorantes na região Noroeste do Estado do Rio de Janeiro, complementando produtos existentes de mapeamento geológico. As rochas carbonáticas servem de matéria-prima para produção de cimento, que atualmente apresenta forte demanda dado o crescimento de obras civis devido à expansão da infraestrutura do Estado do Rio de Janeiro. Este crescimento no consumo oferece desafios às companhias produtoras, tornando-se de vital importância a identificação de novas áreas para exploração de insumos para a indústria civil. Neste sentido, o carbonato tem sofrido grande pressão com relação a sua produção pois é a principal matéria-prima utilizada na fabricação do cimento. Imagens do sensor Aster vem sendo utilizadas na área da geologia com êxito, discriminando litologias e minerais como quartzo, óxido de ferro e calcita. Na região do intervalo de ondas entre 2,235-2,285 μm e 2,295-2,365 μm , as bandas 7 e 8 do sensor ASTER na região do SWIR, mostram-se adequadas para a identificação de minerais de calcita e dolomita. Como metodologia, foram aplicadas as técnicas de razões de bandas para separação de calcários e dolomitos e para a classificação espectral, foi utilizada a técnica SAM. Tornou-se como referência para a classificação espectral amostras de áreas de rochas carbonáticas aflorantes e espectros da biblioteca espectral da USGS. As classificações espectrais obtiveram resultados significativos na discriminação espectral das áreas carbonáticas, no entanto as técnicas de razões de bandas não obtiveram resultados suficientes para a discriminação de calcários e dolomitos. Para trabalhos futuros sugere-se a realização de trabalho de campo para a coleta de espectros, através da espectrorradiometria dos afloramentos dos carbonatos.

塔里木盆地塔北、塔中地区早古生代白云岩形成机理

In Tarim Basin, extensive carbonates of Lower Paleozoic occur, in which thick Cambrian and Lower Ordovician dolostones are widespread and show a potential perspective in hydrocarbon exploration. So they are viewed as an important target for exploration. Tarim Basin is a poly phase composite basin, which underwent multiphase tectonic modification and volcanic activities; these exerted significant influences on the basin-fills and basin fluid evolution, thereby the diagenetic history, particularly on the deep-buried Lower Paleozoic dolostones. Referring to the classification of dolomite texture proposed by Gregg & Sibley (1984) and Sibley & Gregg (1987). In view of crystal size, crystal shape, crystal surface and contact relation, eight genetic textures of dolomite crystals are identified, based on careful petrographic examinatoins. These textures include: 1) micritic dolomite; 2) relict mimetic dolomite; 3)finely crystalline, planar-e(s), floating dolomite; 4)finely crystalline, planar-e(s) dolomite; 5) finely-coarse crystalline, nonplanar-a dolomite; 6)coarse crystalline, nonplanar saddle dolomite; 7) finely-medium crystalline, planar-e(s) dolomite cement; 8) coarse crystalline, nonplanar saddle dolomite cement, in which the former six textures occurs as in matrix, the latter two in the cements. Detailed geochemistry analysis is carried out on the basis of genetic textures of dolomite and related minerals such as quartz and calcite. The result showed that the calcite has the highest average content in Sr, which can be sorted into two groups; micritic dolomite has the highest average content in Sr among all kinds of dolomites; the REE patterns of all kinds of dolomites is similar to those of marine limestone samples. Saddle dolomite cement has δ13C values from -2.44‰ to 1.27‰ PDB, and δ18O values from -13.01‰ to -5.12‰ PDB, which partially overlap with those of matrix dolomite (δ13C values from -2.83‰ to 2.01‰ PDB, δ18O values from -10.63‰ to -0.85‰ PDB). Saddle dolomite cement has 87Sr/86Sr ratios from 0.7086 to 0.7104, which totally overlap with those of matrix dolomite (0.7084 ~ 0.7116). Compared with saddle dolomite derived from other basins all over the world, the saddle dolomites of Tarim Basin have similar δ13C, δ18O and 87Sr/86Sr ratios values with those of matrix dolomite. This scenario reflects the unusual geological setting and special dolomitizing liquid of Tarim Basin. The values of δ18O, δ13C and 87Sr/86Sr ratios of calcite also can be sorted out two groups, which may been resulted from the one stage of extensive uplift of Tarim Basin from Mesozoic to Cenozoic. Fluid inclusion microthermometry data of the diagenetic mineral indicates that matrix dolomite has relatively low homogenization temperatures (Th) of 80～105oC and salinities of 12.3％ (wt% NaCl equivalent); saddle dolomite has highest Th values, which concentrate in 120～160oC and salinities of 13.5～23.7％ (wt% NaCl equivalent); quartz has relatively low Th of 135～155oC and salinities of 17.8～22.5％ (wt% NaCl equivalent); calcite has relatively low Th of 121～159.5oC and salinities of 1.4～17.5％ (wt% NaCl equivalent). These data suggest that the saddle dolomites could have formed in thermal brine fluids. Based on comprehensive petrographical study, detailed geochemistry and fluid inclusion microthermometry analysis on Lower Paleozoic dolomite of Tarim Basin, three types of dolomitisation mechanism are proposed: Penecontemporaneous dolomitisation (Sabkha dolomitisation & Reflux dolomitisation); Burial dolomitisation (shallow-intermediate burial dolomitisation & Deep burial dolomitisation ); Hydrothermal cannibalized dolomitisation. In view of host-specified occurrences of hydrothermal dolomite, the low abundance of saddle dolomite and high geochemical similarities between saddle dolomite and host dolomite, as well as highest Th and high salinities , the hydrothermal dolomite in Tarim Basin is thus unique, which could have been precipitated in modified fluid in the host dolomite through intraformational thermal fluid cannibalization of Mg ions from the host. This scenario is different from the cases that large scale dolomitizing fluid migration took place along the fluid pathways where abundant saddle dolomite precipitated. Detailed observations on 180 petrographic and 60 casting thin sections show original pores in Lower Paleozoic dolomite were almost died out by complicated diagenetic process after a long time geologic evolution. On the other hand, deep-buried dolomite reservoirs is formed by tectonic and hydrothermal reforming on initial dolomites. Therefore, the distribution of structure-controlled hydrothermal dolomite reservoirs is predicted in Tabei and Tazhong Area of Tarim Basin based on the geophysical data.

塔里木盆地柯坪-巴楚露头区白云岩成岩作用机理研究

Through field outcrop dolomite observation, laboratory petrography (macroscopy, microscopy, cathodeluminescence and scan electronic microscopy), geochemistry (carbon-oxygen-strontium isotopes and trace elements) and fluid inclusion microthermometry study in Keping-Bachu area of Tarim Basin, it can be inferred that there are existing eight dolomite texture types within four evolution phases in Keping-Bachu area of Tarim Basin. The paragenesis of different dolomite texture types and associated minerals in Keping-Bachu area has been established. The carbon and oxygen isotopes of saddle dolomites and matrix dolomites overlap greatly. The Strontium isotopes results of Keping-Bachu outcrop area show that the strontium isotopes differentiation of the matrix and saddle dolomites is not obvious, the reason of which is that there is thousands of Cambrian-Ordovician dolomite strata below the stratum bearing the saddle dolomite. In the process of the heat flow upward migration, the isotopes of the heat interacts with the host rock, which leads to the similarity betwwen the strontium of the saddle dolomite and matrix dolomite. The strontium isotope of the saddle dolomite is not very radiogenic. the six types samples within four phases in the study area show Eu negatively. Comparing to the other types of samples, the δEu of saddle dolomite is relatively high falling into the range of 0.510-0.874, which shows that the saddle dolomite forms in the hydrothermal setting and is affected by the hydrothermal activity to some extend.The Lan/Ybn of saddle dolomite is high up to 15.726, which means that the HREE is very rich. It belongs to the typical hydrothermal genesis model. The δCe of saddle dolomite is positive anomaly, which is the result of high effect from the land source debris. The homogeneous temperature of the saddle dolomite falls into two ranges 110-120℃ and 125-160℃, after pressure correction, they are 141-152℃，157.5-196℃, the salinity of the saddle dolomite can reach to 20-25%. With the comparing with the burial history, the Th of the saddle dolomite is high than the ambient strata temperature, these data show that the saddle dolomite is of hydrothermal origin. The evolution trend of different dolomite and associated minerals is from matrix dolomite, dolomite cementation, saddle dolomite, quartz to calcite. Alonging with this evolution trend, the temperature of the diagenetic flow initiated from 80-100℃, after rising to 135-160℃, then gradually declined. Finally, a structurally-controlled dolomitization model is established in Keping-Bachu area of Tarim Basin.