ESEM observations of SCC initiation for 4340 high strength steel in distilled water

The stress corrosion cracking (SCC) initiation process for 4340 high strength steel in distilled water at room temperature was studied using a new kind of instrument: an environmental scanning electron microscope (ESEM). It was found that the applied stress accelerated oxide film formation which has an important influence on the subsequent SCC initiation. SCC was observed to initiate in the following circumstances: (1) cracking of a thick oxide film leading to SCC initiation along metal grain boundaries, (2) the initiation of pits initiating SCC in the metal and (3) SCC initiating from the edge of the specimen. All these three SCC initiation circumstances are consistent with the following model which couples SCC initiation with cracking of a surface protective oxide. There is a dynamic interaction between oxide formation, the applied stress, oxide cracking, pitting and the initiation of SCC. An aspect of the dynamic interaction is cracks forming in a protective surface oxide because of the applied stress, exposing to the water bare metal at the oxide crack tip, and oxidation of the bare metal causing crack healing. Oxide crack healing would be competing with the initiation of intergranular SCC if an oxide crack meets the metal surface at a grain boundary. If the intergranular SCC penetration is sufficiently fast along the metal grain boundary, then the crack yaws open preventing healing of the oxide crack. If intergranular SCC penetration is not sufficiently fast, then the oxidation process could produce sufficient oxide to fill both the stress corrosion crack and the oxide crack; in this case there would be initiation of SCC but only limited propagation of SCC. Stress-induced cracks in very thin oxide can induce pits which initiate SCC, and under some conditions such stress induced cracks in a thin oxide can directly initiate SCC.

Hardness and compressive strength of indirect composite resins: effects of immersion in distilled water

The aim of this study was to evaluate the effect of ageing in distilled water on the hardness and compressive strength of a direct composite resin Z100, a feldspatic porcelain (Noritake) and three indirect composites (Artglass, Solidex and Targis). For the Vickers hardness tests, five disk-shaped specimens (2 x 4 mm) of each material were prepared according to the manufacturers' instructions. The hardness tests were conducted using a Vickers diamond indentor. Compressive strength measurements were recorded on cylindrical specimens with a diameter of 6 mm and a length of 12 mm. The compression tests were carried out with a constant cross-head speed of 0.5 mm min(-1) on a mechanical test machine. For each material, 10 specimens were tested after 7 days of dry storage at 37 +/- 1 degreesC and 10 specimens were tested after water storage at 37 +/- 1 degreesC for 180 days. Noritake porcelain specimens showed higher hardness values than the composites. Among the composite materials, Z100 promoted the highest VHN values, regardless of the ageing periods. The results showed that Solidex and Z100 had the highest compressive strength values. Ageing in water reduced the hardness for all composites, but had no long-term effect on the compressive strength.

Occurrence of molds on laminated paperboard for aseptic packaging, selection of the most hydrogen peroxide- and heat-resistant isolates and determination of their thermal death kinetics in sterile distilled water

This study aimed at enumerating molds (heat-labile and heat-resistant) on the surface of paperboard material to be filled with tomato pulps through an aseptic system and at determining the most heat-and hydrogen peroxide-resistant strains. A total of 118 samples of laminated paperboard before filling were collected, being 68 before and 50 after the hydrogen peroxide bath. Seven molds, including heat-resistant strains (Penicillium variotii and Talaromyces flavus) with counts ranging between 0.71 and 1.02 CFU/cm(2) were isolated. P. variotii was more resistant to hydrogen peroxide than T. flavus and was inactivated after heating at 85 degrees C/15 min. When exposed to 35 % hydrogen peroxide at 25 degrees C, T. flavus (F5E2) and N. fischeri (control) were less resistant than P. variotti (F1A1). P. citrinum (F7E2) was shown to be as resistant as P. variotti. The D values (the time to cause one logarithmic cycle reduction in a microbial population at a determined temperature) for spores of P. variotii (F1A1) and N. fischeri (control) with 4 months of age at 85 and 90 degrees C were 3.9 and 4.5 min, respectively. Although the contamination of packages was low, the presence of heat-and chemical-resistant molds may be of concern for package sterility and product stability during shelf-life. To our knowledge, this is the first report that focuses on the isolation of molds, including heat-resistant ones, contaminating paperboard packaging material and on estimating their resistance to the chemical and physical processes used for packaging sterilization.

How to prolong life : an inquiry into the cause of old age and natural death, showing the diet and agents best adapted for a lengthened prolongation of human life on earth : rejuvenescence by means of phosphorus & distilled water /

Mode of access: Internet.

The solubility of carbon dioxide in distilled water, synthetic sea water and synthetic sea-water concentrates,

Mode of access: Internet.

The response of lichen growth to additions of distilled water, rainwater and water from a rock surface

Three lichen species were wetted in the field with distilled water, rainwater or water which had run off a rock surafce, during July 1974 to February 1975. The radial growth rate of Parmelia glabratula ssp. fuliginosa was not influenced by the wetting treatments. The radial growth rate of P. conspersa with the distilled water was greater than the control, rainwater and runoff treatments. The radial growth rate of Physcia orbicularis was lower with rainwater and runoff treatmentss than the control and distilled water treatment. These results may be explained by the effect of wetting on the carbon balance of the lichens and by the influence of water chemistry.

Evaluation of HA negatively charged membranes in the recovery of human adenoviruses and hepatitis A virus in different water matrices

Human adenoviruses (HAdV) and hepatitis A virus (HAV) are shed in the faeces and consequently may be present in environmental waters, resulting in an increase in pathogen concentration that can affect water quality and human health. The aim of this study was to evaluate an adsorption-elution method which utilizes negatively charged membrane HA to determine the efficient recovery of HAdV and HAV from different water matrices and to combine this procedure with a qualitative molecular method (nested RT-PCR and nested PCR). The best efficiency recovery was achieved in distilled water and treated wastewater effluent (100%) for both viruses and in recreational lagoon water for HAV (100%). The efficiency recovery was 10% for HAdV and HAV in seawater and 10% for HAdV in lagoon water. The viral detection limit by nested PCR for HAV in water samples ranged between 20-0.2 FFU/mL and 250 and 25 TCID50/mL for HAdV. In conclusion, these results suggest that the HA negatively charged membranes vary their efficiency for recovery of viral concentration depending upon the types of both enteric viruses and water matrices.

Effect of water contamination on the shear bond strength of five orthodontic adhesives

Objectives: To evaluate the shear bond strength and site of failure of brackets bonded to dry and wet enamel. Study design: 50 teeth were divided into ten groups of 5 teeth each (10 surfaces). In half the groups enamel was kept dry before bonding, and in the other half distilled water was applied to wet the surface after etching. The following groups were established: 1)Acid/Transbond-XT (dry/wet) XT; 2) Transbond Plus Self Etching Primer (TSEP)/Transbond-XT paste (dry/wet); 3) Concise (dry), Transbond MIP/Concise (wet), 4) FujiOrtho-LC (dry/wet); 5) SmartBond (dry/wet). Brackets were bonded to both buccal and lingual surfaces. Specimens were stored in distilled water (24 hours at 37ºC) and thermocycled. Brackets were debonded using a Universal testing machine (cross-head speed 1 mm/min). Failure sites were classified using a stereomicroscope. Results: No significant differences in bond strength were detected between the adhesives under wet and dry conditions except for Smart- Bond, whose bond strength was significantly lower under dry conditions. For all the adhesives most bond failures were of mixed site location except for Smartbond, which failed at the adhesive-bracket interface. Conclusions: Under wet conditions the bonding capacity of the adhesives tested was similar than under dry conditions, with the exception of SmartBond which improved under wet conditions

Water uptake by Annona diversifolia Saff. and A. purpurea Moc. & sessé ex dunal seeds (Annonaceae)

Annonaceae seeds are known by presenting dormancy mechanisms, whose reports ranging from coating impermeable to the physiological dormancy. By this way, the present study aimed to evaluate water uptake in Annona diversifolia Saff and Annona purpurea Moc & Sessé ex Dunal seeds. For this study, seeds were placed under immersion in distilled water, and used four replicates of 25 seeds of each species, which were weighed during the 480 hours that were immersed. To determine the place of purchase of water, Annona diversifolia seeds were sealed with paraffin at different locations. Based on the results, seeds from both species reached the phases I and II of water uptake, which indicates they are not hard; however, germination (Phase III) was not reached. Annona diversifolia seeds completed Phase I with, 50h and Annona purpurea with 70h from imbibitions begin, which shows that even slowly, water is acquire.

Central lead administration inhibits water intake and sodium appetite in rats

We have demonstrated that acute third ventricle injections of lead acetate (PbAc) exert a powerful antidipsogenic effect and induce a significant increase in renal sodium excretion. In the present study we confirm the antidipsogenic effect of lead and demonstrate that central administration of this metal, in minute amounts, significantly reduces salt intake both during dehydration and after central angiotensinergic stimulation. Adult male Wistar rats had the third ventricle cannulated seven days before the experiments. During this period they had free access to distilled water and hypertonic saline solution (1.5%). After a 24-h period of fluid deprivation, experimental animals received third ventricle injections of PbAc (0.3, N = 8 and 3.0 nmol/rat, N = 14) while controls received sodium acetate (NaAc; 3.0 nmol/rat, N = 10). Rats treated with PbAc at the highest dose showed a significant reduction (P<0.05) both in water and hypertonic saline intake when compared to controls. When the effect of lead administration on angiotensin II-induced water and salt intake was studied, normohydrated animals received third ventricle injections of angiotensin II (9.6 nmol/rat) after pretreatment with 3.0 nmol/rat of PbAc (experimental group, N = 10) or NaAc (controls, N = 8). The group pretreated with PbAc presented a significant reduction (P<0.05) in both water and salt intake compared to controls. Thus, this study confirms the antidipsogenic effect of central lead injections and demonstrates that the presence of lead in the brain exerts a significant inhibition of sodium appetite.

Effects of the mechanical damage on the water absorption process by corn kernel

The purpose of this study was to investigate and model the water absorption process by corn kernels with different levels of mechanical damage Corn kernels of AG 1510 variety with moisture content of 14.2 (% d.b.) were used. Different mechanical damage levels were indirectly evaluated by electrical conductivity measurements. The absorption process was based on the industrial corn wet milling process, in which the product was soaked with a 0.2% sulfur dioxide (SO2) solution and 0.55% lactic acid (C3H6O3) in distilled water, under controlled temperatures of 40, 50, 60, and 70 ºC and different mechanical damage levels. The Peleg model was used for the analysis and modeling of water absorption process. The conclusion is that the structural changes caused by the mechanical damage to the corn kernels influenced the initial rates of water absorption, which were higher for the most damaged kernels, and they also changed the equilibrium moisture contents of the kernels. The Peleg model was well adjusted to the experimental data presenting satisfactory values for the analyzed statistic parameters for all temperatures regardless of the damage level of the corn kernels.

Shear Bond Strength of Different Repair Systems to Titanium After Water Aging

This study evaluated the shear bond strength (SBS) and stability of commercially pure titanium (CP Ti)/repair material interfaces promoted by different repair systems. One hundred CP Ti cast discs were divided into five repair system groups: 1) Epricord (EP); 2) Bistite 11 DC (BT); 3) Cojet (CJ); 4) Scotchbond Multi-Purpose Plus (SB) (control group); and 5) Cojet Sand plus Scotchbond Multi-Purpose Plus (CJSB). The specimens were stored in distilled water for 24 hours at 37 degrees C, thermal cycled (5000 cycles, 5 degrees-55 degrees C) and stored under the same conditions for either 24 hours or six months (n=10). SBS was tested and the data were analyzed by two-way analysis of variance (ANOVA) and Tukey test (alpha=.05). Failure mode was determined with a stereomicroscope (20x). The repair system, storage time, and their interaction significantly affected the SBS (p<0.001). At 24 hours, CJSB exhibited the highest SBS value, followed by CJ. At six months, these two groups had similar mean SBS (p>0.05) and higher means in comparison to the other groups. For both storage times, BT presented the lowest SBS, while the EP and SB groups did not differ significantly from one another (p>0.05). There were no significant differences in SBS between the storage times for the groups EP and CJ (p>0.05). The groups BT, SB, and CJSB showed 100% adhesive failure, irrespective of storage time. The CJSB group showed the highest SBS at both storage times. At six months, the CJ group exhibited a similar SBS mean value when compared to the CJSB group. Water storage adversely affected the groups BT, SB (control group), and CJSB. Considering SBS values, stability, and the failure mode simultaneously, the CJ group showed the best CP Ti repair performance.

Degradation of sulfamethoxazole in water by solar photo-Fenton. Chemical and toxicological evaluation

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

EFFECT OF WATER POTENTIAL ON GERMINATION OF SEEDS OF STYLOSANTHES-GUIANENSIS (AUBL) SW

Effect of water potential on germination of seeds of Slylosanthes guianensis (Aubl.) Sw. To evaluate the water potential effect on germination of S. guianensis two experiments were performed.The first one used osmotic pre-treatment in the imbibition phase and after this period (14 h) the seeds were germinated on filter paper moistened with distilled water. In the second experiment, besides the imbibition phase, seeds were kept in a range of water potentials during all the process. The potentials ranged from 0 to -18 bars, with 3 bars increments, induced by mannitol or by polyethylene glycol. Each treatment was replicated 3 times with 100 seeds per replication. The seeds pre-treated during imbibition had high germination percentage, the highest being the ones in polhyetylene glycol. In the second experiment the polyethylene glycol solutions reduced dramatically the germination percentage in relation to mannitol. From -12 bars on germination ceased in the polyethylene glycol treatments, while in mannitol solution there was 52,67% of germination, in the same water potential.