Sequential injections as an alternative to gradient exploitation for implementing differential kinetic analysis in a flow injection system

A novel flow-based strategy for implementing simultaneous determinations of different chemical species reacting with the same reagent(s) at different rates is proposed and applied to the spectrophotometric catalytic determination of iron and vanadium in Fe-V alloys. The method relies on the influence of Fe(II) and V(IV) on the rate of the iodide oxidation by Cr(VI) under acidic conditions, the Jones reducing agent is then needed Three different plugs of the sample are sequentially inserted into an acidic KI reagent carrier stream, and a confluent Cr(VI) solution is added downstream Overlap between the inserted plugs leads to a complex sample zone with several regions of maximal and minimal absorbance values. Measurements performed on these regions reveal the different degrees of reaction development and tend to be more precise Data are treated by multivariate calibration involving the PLS algorithm The proposed system is very simple and rugged Two latent variables carried out ca 95% of the analytical information and the results are in agreement with ICP-OES. (C) 2010 Elsevier B V. All rights reserved.

A comparison of methods for differential expression analysis of RNA-seq data.

BACKGROUND: Finding genes that are differentially expressed between conditions is an integral part of understanding the molecular basis of phenotypic variation. In the past decades, DNA microarrays have been used extensively to quantify the abundance of mRNA corresponding to different genes, and more recently high-throughput sequencing of cDNA (RNA-seq) has emerged as a powerful competitor. As the cost of sequencing decreases, it is conceivable that the use of RNA-seq for differential expression analysis will increase rapidly. To exploit the possibilities and address the challenges posed by this relatively new type of data, a number of software packages have been developed especially for differential expression analysis of RNA-seq data. RESULTS: We conducted an extensive comparison of eleven methods for differential expression analysis of RNA-seq data. All methods are freely available within the R framework and take as input a matrix of counts, i.e. the number of reads mapping to each genomic feature of interest in each of a number of samples. We evaluate the methods based on both simulated data and real RNA-seq data. CONCLUSIONS: Very small sample sizes, which are still common in RNA-seq experiments, impose problems for all evaluated methods and any results obtained under such conditions should be interpreted with caution. For larger sample sizes, the methods combining a variance-stabilizing transformation with the 'limma' method for differential expression analysis perform well under many different conditions, as does the nonparametric SAMseq method.

Differential proteome analysis of mature and germinated embryos of Araucaria angustifolia

Araucaria angustifolia is an endangered Brazilian native conifer tree. The aim of the present work was to identify differentially expressed proteins between mature and germinated embryos of A. angustifolia, using one and two dimensional gel electrophoresis approaches followed by protein identification by tandem mass spectrometry. The identities of 32 differentially expressed protein spots from two dimensional gel maps were successfully determined, including proteins and enzymes involved in storage mobilization such as the vicilin-like storage protein and proteases. A label free approach, based on spectral counts, resulted in detection of 10 and 14 mature and germinated enriched proteins, respectively. Identified proteins were mainly related to energetic metabolism pathways, translational processes. oxidative stress regulation and cellular signaling. The integrated use of both strategies permitted a comprehensive protein expression overview of changes in germinated embryos in relation to matures, providing insights into the this process in a recalcitrant seed species. Applications of the data generated on the monitoring and control of in vitro somatic embryos were discussed. Published by Elsevier Ltd.

Differential proteomic analysis of Acidithiobacillus ferrooxidans cells maintained in contact with bornite or chalcopyrite: Proteins involved with the early bacterial response

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

A preliminary differential proteomic analysis of the periplasmic fraction in Acidithiobacillus ferrooxidans planktonic and attached cells exposed to chalcopyrite

The Acidithiobacillus ferrooxidans periplasmic space is known to have proteins involved in the respiratory chains. There are no reports about the expression of the periplasmic proteins in A. ferrooxidans cells attached to chalcopyrite. In this preliminary work, it was compared the periplasmic protein profiles of A. ferrooxidans planktonic and attached cells after exposure to chalcopyrite for 2 hours. The bacterial response to chalcopyrite was investigated by a proteomic approach (two- dimensional gel electrophoresis and mass spectrometry). Four proteins differentially expressed between planktonic and attached cells after exposure to chalcopyrite were identified. Two of these proteins, repressed in chalcopyrite- attached cells, were both identified as superoxide dismutase, whereas the single strand binding protein (SSB) and the PspA/IM30 protein were induced. These results showed that A. ferrooxidans chalcopyrite- attached and planktonic cells show differential expression of the periplasmic proteins and that a proteomic approach can provide a valuable tool to detect proteins related to the A. ferrooxidans response to attachment to the mineral substrates. © (2009) Trans Tech Publications.

Differential Proteomic Analysis of Noncardia Gastric Cancer from Individuals of Northern Brazil

Gastric cancer is the second leading cause of cancer-related death worldwide. The identification of new cancer biomarkers is necessary to reduce the mortality rates through the development of new screening assays and early diagnosis, as well as new target therapies. In this study, we performed a proteomic analysis of noncardia gastric neoplasias of individuals from Northern Brazil. The proteins were analyzed by two-dimensional electrophoresis and mass spectrometry. For the identification of differentially expressed proteins, we used statistical tests with bootstrapping resampling to control the type I error in the multiple comparison analyses. We identified 111 proteins involved in gastric carcinogenesis. The computational analysis revealed several proteins involved in the energy production processes and reinforced the Warburg effect in gastric cancer. ENO1 and HSPB1 expression were further evaluated. ENO1 was selected due to its role in aerobic glycolysis that may contribute to the Warburg effect. Although we observed two up-regulated spots of ENO1 in the proteomic analysis, the mean expression of ENO1 was reduced in gastric tumors by western blot. However, mean ENO1 expression seems to increase in more invasive tumors. This lack of correlation between proteomic and western blot analyses may be due to the presence of other ENO1 spots that present a slightly reduced expression, but with a high impact in the mean protein expression. In neoplasias, HSPB1 is induced by cellular stress to protect cells against apoptosis. In the present study, HSPB1 presented an elevated protein and mRNA expression in a subset of gastric cancer samples. However, no association was observed between HSPB1 expression and clinicopathological characteristics. Here, we identified several possible biomarkers of gastric cancer in individuals from Northern Brazil. These biomarkers may be useful for the assessment of prognosis and stratification for therapy if validated in larger clinical study sets.

Differential expression analysis for sequence count data via mixtures of negative binomials

The recent advent of Next-generation sequencing technologies has revolutionized the way of analyzing the genome. This innovation allows to get deeper information at a lower cost and in less time, and provides data that are discrete measurements. One of the most important applications with these data is the differential analysis, that is investigating if one gene exhibit a different expression level in correspondence of two (or more) biological conditions (such as disease states, treatments received and so on). As for the statistical analysis, the final aim will be statistical testing and for modeling these data the Negative Binomial distribution is considered the most adequate one especially because it allows for "over dispersion". However, the estimation of the dispersion parameter is a very delicate issue because few information are usually available for estimating it. Many strategies have been proposed, but they often result in procedures based on plug-in estimates, and in this thesis we show that this discrepancy between the estimation and the testing framework can lead to uncontrolled first-type errors. We propose a mixture model that allows each gene to share information with other genes that exhibit similar variability. Afterwards, three consistent statistical tests are developed for differential expression analysis. We show that the proposed method improves the sensitivity of detecting differentially expressed genes with respect to the common procedures, since it is the best one in reaching the nominal value for the first-type error, while keeping elevate power. The method is finally illustrated on prostate cancer RNA-seq data.

Use of differential display analysis to assess the effect of human cytomegalovirus infection on the accumulation of cellular RNAs: Induction of interferon-responsive RNAs

We used differential display analysis to identify mRNAs that accumulate to enhanced levels in human cytomegalovirus-infected cells as compared with mock-infected cells. RNAs were compared at 8 hr after infection of primary human fibroblasts. Fifty-seven partial cDNA clones were isolated, representing about 26 differentially expressed mRNAs. Eleven of the mRNAs were virus-coded, and 15 were of cellular origin. Six of the partial cDNA sequences have not been reported previously. All of the cellular mRNAs identified in the screen are induced by interferon α. The induction in virus-infected cells, however, does not involve the action of interferon or other small signaling molecules. Neutralizing antibodies that block virus infection also block the induction. These RNAs accumulate after infection with virus that has been inactivated by treatment with UV light, indicating that the inducer is present in virions. We conclude that human cytomegalovirus induces interferon-responsive mRNAs.

Phase transitions of cassava starch dispersions prepared with glycerol solutions

The aim of this work was to study the glass transition, the glass transition of the maximally freeze-concentrated fractions, the ice melting and the gelatinization phenomenon in dispersions of starch prepared using glycerol- water solutions. The starch concentration was maintained constant at 50 g cassava starch/100 g starch dispersions, but the concentration of the glycerol solutions was variable (C-g= 20, 40, 60, 80 and 100 mass/mass%). The phase transitions of these dispersions were studied by calorimetric methods, using a conventional differential scanning calorimeter (DSC) and a more sensitive equipment (micro-DSC). Apparently, in the glycerol diluted solutions (20 and 40%), the glycerol molecules interacted strongly with the glucose molecules of starch. While in the more concentrated glycerol domains (C-g> 40%), the behaviour was controlled by migration of water molecules from the starch granules, due to a hypertonic character of glycerol, which affected all phase transitions.

Microinjection molding of polyamide 6/carbon nanotube composites

Microinjection molding of polymer composites with carbon nanotubes (CNT) requires previous production of the nanocomposites, often by melt extrusion. Each processing step has a thermo-mechanical effect on the polymer melt, conveying different properties to the final product. In this work, polyamide 6 and its composites with pristine and functionalized CNT (f-CNT) were processed by a mini twin-screw extrusion, followed by microinjection molding. The morphology induced on the polymer by each process was analyzed by differential scanning calorimetry and wide angle X-ray diffraction. Calorimetric analysis showed a secondary crystallization for the microinjected materials, absent for the extruded materials. The characterization of microinjected polyamide 6 by X-ray diffraction revealed a large contribution of the c phase to the total crystallinity, mainly in the skin region, while the nanocomposites and extruded materials were characterized by a larger contribution of the a phase. Functionalization of CNT did not affect significantly the polymer morphology compared to composites with pristine CNT.

RNA-seq analysis of the Quercus suber root response to drought

Dissertação de mestrado em Plant Molecular Biology, Biotechnology and Bioentrepreneurship

Análisis de sistemas bucoadhesivos

[spa]Objetivo: El objetivo de este estudio es el diseño de un parche bucoadhesivo para la administración transbucal de clorhidrato de doxepina utilizando diferentes polímeros así como la caracterización de dichos sistemas en cuanto al análisis calorimétrico y la capacidad de hinchamiento.Materiales y métodos: Se ha utilizado clorhidrato de doxepina y diferentes polímeros, carboximetilcelulosa sódica, hidroxipropilmetilcelulosa y chitosan. La calorimetría diferencial de barrido (DSC) se ha realizado en un dispositivo Mettler FP 80 equipado con un horno FP 85 y la capacidad de hinchamiento utilizando placas de agar.Resultados: Se obtienen termogramas de los parches y las mezclas físicas donde se observan transiciones endotérmicas entre 30 y 120º C y el pico endotérmico del principio activo en las mezclas físicas binarias. La entalpía de deshidratación es similar en los polímeros de carboximetilcelulosa sódica y chitosan (281 J/g) siendo menor en la película de hidroxipropilmetilcelulosa (251 J/g), al igual que el porcentaje de hidratación donde se demuestra que los parches elaborados con hidroxipropilmetilcelulosa presenta menor tendencia a captar agua (55,91 %) frente al 67,04 % y 67,30 % de la carboximetilcelulosa sódica y chitosan, respectivamente.Conclusión: Los resultados obtenidos muestran que existe compatibilidad entre los componentes de la formulación y los datos de entalpía se correlacionan con los datos obtenidos en el ensayo de hinchamiento.[eng]The aim of this study is to design a bucoadhesive patch for the transbuccal administration of doxepin hydrochloride using different polymers as well as the characterization of these systems for calorimetric analysis and the swelling capacity. Materials and methods: Doxepin hydrochloride was used as well as various polymers; carboxymethylcellulose sodium, hydroxypropylmethyl cellulose and chitosan. Differential scanning calorimetry (DSC) was carried out using a Mettler FP 80 device equipped with a FP 85 oven and the swelling capacity using agar plates. Results: Thermograms obtained patches and physical mixtures where there are endothermic transitions between 30 and 120º C and the endothermic peak of the active principle in binary physical mixtures. Dehydration enthalpy is similar in polymers of carboxymethylcellulose sodium and chitosan (281 J/g), the film having less hydroxypropylmethylcellulose (251 J/g), the percentage of moisture shows that the patches prepared with hydroxypropylmethylcellulose have less tendency to collect water (55.91 %) compared to 67.04 % and 67.30 % with sodium carboxymethylcellulose and chitosan, respectively. Conclusion: The results show that there is compatibility between the components of the formulation and the enthalpy data correlate

Análisis de sistemas bucoadhesivos

[spa]Objetivo: El objetivo de este estudio es el diseño de un parche bucoadhesivo para la administración transbucal de clorhidrato de doxepina utilizando diferentes polímeros así como la caracterización de dichos sistemas en cuanto al análisis calorimétrico y la capacidad de hinchamiento.Materiales y métodos: Se ha utilizado clorhidrato de doxepina y diferentes polímeros, carboximetilcelulosa sódica, hidroxipropilmetilcelulosa y chitosan. La calorimetría diferencial de barrido (DSC) se ha realizado en un dispositivo Mettler FP 80 equipado con un horno FP 85 y la capacidad de hinchamiento utilizando placas de agar.Resultados: Se obtienen termogramas de los parches y las mezclas físicas donde se observan transiciones endotérmicas entre 30 y 120º C y el pico endotérmico del principio activo en las mezclas físicas binarias. La entalpía de deshidratación es similar en los polímeros de carboximetilcelulosa sódica y chitosan (281 J/g) siendo menor en la película de hidroxipropilmetilcelulosa (251 J/g), al igual que el porcentaje de hidratación donde se demuestra que los parches elaborados con hidroxipropilmetilcelulosa presenta menor tendencia a captar agua (55,91 %) frente al 67,04 % y 67,30 % de la carboximetilcelulosa sódica y chitosan, respectivamente.Conclusión: Los resultados obtenidos muestran que existe compatibilidad entre los componentes de la formulación y los datos de entalpía se correlacionan con los datos obtenidos en el ensayo de hinchamiento.[eng]The aim of this study is to design a bucoadhesive patch for the transbuccal administration of doxepin hydrochloride using different polymers as well as the characterization of these systems for calorimetric analysis and the swelling capacity. Materials and methods: Doxepin hydrochloride was used as well as various polymers; carboxymethylcellulose sodium, hydroxypropylmethyl cellulose and chitosan. Differential scanning calorimetry (DSC) was carried out using a Mettler FP 80 device equipped with a FP 85 oven and the swelling capacity using agar plates. Results: Thermograms obtained patches and physical mixtures where there are endothermic transitions between 30 and 120º C and the endothermic peak of the active principle in binary physical mixtures. Dehydration enthalpy is similar in polymers of carboxymethylcellulose sodium and chitosan (281 J/g), the film having less hydroxypropylmethylcellulose (251 J/g), the percentage of moisture shows that the patches prepared with hydroxypropylmethylcellulose have less tendency to collect water (55.91 %) compared to 67.04 % and 67.30 % with sodium carboxymethylcellulose and chitosan, respectively. Conclusion: The results show that there is compatibility between the components of the formulation and the enthalpy data correlate

Caracterização físico-química do óleo essencial da Siparuna guianensis Aublet

Thermal and spectroscopic analyses of essential oil extracted from Siparuna guianensis Aublet, an aromatic plant belonging to medicinal ethnobotany family Siparunaceae, were carried out. The plant is known throughout the North and Northeast of Brazil by the name negramina and has wide application as a natural insect repellent. Thermogravimetric analyses were correlated with the Arrhenius Equation to provide kinetic parameters of evaporation, including activation energy and frequency factor. Differential scanning calorimetric analysis showed the presence of an exothermic oxidation peak, probably as a result of transformations and decomposition of the solid structure before melting.